Related
Hi Guys
I have a problem with my TyTN at the moment.
My device is not charging.
Yesterday i put it in my Docking Station and wait a little time.
But Now the Tynt isnt charged.
I think ist a Problem with my TyTN Hardware.
I have all Power Supplys used they i have, but it doesent work.
Can you help me?
Its this a problem with the accu or a fuse on the circuit ?
Sorry for my broken english i hope you understand me.
Regards Patrik Laube
Hello,
first of all, try to soft reset the device.
If it fails, hard reset it.
If it doesn't work, go the service center.
Good luck
The above advice is fine. But you did not say if any of the LEDs are lit.
Do you get the red NO CHARGE LED?
Does your phone operate normally except for not charging?
Mike
Hello
My Phone is working fine but i cant charge it with the original HTC adapter.
I must load the accu with a special loader.
USB and Charge dont work....
And i have no warranty I cant send it to my operator.
When i plug in the USB Cable it doesent make everthing.
I think it was a to high voltage on the USB or the USB Ground ( - ) had a electrical Power for a litte moment.
Have you an idea?
Thanks for yur help.
Regards Patrik
I had a similar problem, which was sorted by a new rom, but I ascertained it was software problem when I realised it charged when powered off.
PatrikLaube said:
Hello
USB and Charge dont work....
And i have no warranty I cant send it to my operator.
Have you an idea?
Thanks for yur help.
Regards Patrik
Click to expand...
Click to collapse
hi,
try this: when your device is connected via usb, tab on the battery icon in the taskbar on you device, go to the register "advanced" and check/uncheck "When Device is turned on, do not charge the battery when connected to the pc"
thats it
greetz
mizi
I'm having an issue along these lines, also.
My phone has been working fine untill the other night when I tried to charge it via the wall electrical outlet. It will not charge at all, the battery has been drained to nothing and I can't turn it on. The yellowish light doesn't turn on when I plug it in like it used to.
I don't know if this is a battery issue or an issue with the USB connection inside of the phone. On a side note, when it did have power and I tried to connect it to the USB via the PC; it didn't work. The phone was on, but the computer didn't even notice the phone was plugged in. That leads me to believe it would be a connection issue; but I'm not quite sure.
If anyone has anything they can add to this I would appreciate it, thank you.
P.S. Bringing it to a service center is a bit out of the question in the mean time seeing as it was bought on eBay and funds are limited for the time-being.
MiZi666 said:
hi,
try this: when your device is connected via usb, tab on the battery icon in the taskbar on you device, go to the register "advanced" and check/uncheck "When Device is turned on, do not charge the battery when connected to the pc"
thats it
greetz
mizi
Click to expand...
Click to collapse
Hello, I cannot find the "When Device is turned on, do not charge the battery when connected to the pc" in my device. My Rom is WM6.1 CE OS 5.2.20273 cooked by dvha79_ddt.
My HTC TyTN has the sample problem, but i can use the USB to charge normally. It cannot work using my AC adapter Only when the device is open...
About your Battery Issue.
I'll tell you exactly why ur phone isnt charging anymore... If you have been charging it alot on the USB or pretty much any!! charging on the USB u have killed ur battery, never charge your phone on the USB it kinda sucks they should make these phones able to be Sync'd thru USB without a battery cause these batteries should not be powered thru the USB over Time... from syncing to your pc will kill these batteries i have noticed that when u sync this Tytn Ithru USB and the device is at say 70% it charges up to 100% pretty fast i would recommand to you and anyone who reads this dont sync your TYTN or any HTCC phone for to long to the USB Cause it will Trash your batteries Life down the road... Hope this was HELPFUL.
Cheers
Paul
PatrikLaube said:
Hello
My Phone is working fine but i cant charge it with the original HTC adapter.
I must load the accu with a special loader.
USB and Charge dont work....
And i have no warranty I cant send it to my operator.
When i plug in the USB Cable it doesent make everthing.
I think it was a to high voltage on the USB or the USB Ground ( - ) had a electrical Power for a litte moment.
Have you an idea?
Thanks for yur help.
Regards Patrik
Click to expand...
Click to collapse
hi, did anyone solve this problem ? ive got the same problem with my htc touch cruise, i think it charges when turned off but doesnt when on. the orange light doesnt turn on when i plug usb to charge it and it doesnt sync thru the PC neither.
Does anyone has a solution to this ?Thanks a lot!
does anyone has a solution to this ?
hi, did anyone solve this problem ? ive got the same problem with my htc touch cruise, i think it charges when turned off but doesnt when on. the orange light doesnt turn on when i plug usb to charge it and it doesnt sync thru the PC neither.
Does anyone has a solution to this ?Thanks a lot!
^I'm having the same problem with my herm200. I did the soft reset, hard reset changed ROMs but still the same problem. I don't think it's the usb connector because if it is it wouldn't have been able to charge the phone even if it's turned off. Before I'm able to charge it turned on but it would take a few minutes before the orange led turns on, but when I use the phone or if I receive a text the orange led would turn off it's like the charger disconnects but after a few minutes it would go back again. Now it just wouldn't charge turned on, sometimes it gets worse where it just wouldn't charge on or off.
Now I'm already planning to buy an external battery charger.
gypsygirl13 said:
^I'm having the same problem with my herm200. I did the soft reset, hard reset changed ROMs but still the same problem. I don't think it's the usb connector because if it is it wouldn't have been able to charge the phone even if it's turned off. Before I'm able to charge it turned on but it would take a few minutes before the orange led turns on, but when I use the phone or if I receive a text the orange led would turn off it's like the charger disconnects but after a few minutes it would go back again. Now it just wouldn't charge turned on, sometimes it gets worse where it just wouldn't charge on or off.
Now I'm already planning to buy an external battery charger.
Click to expand...
Click to collapse
Are you using an official 1000mA charger? (Not a 500mA one) 500mA ones work, but they are under-powered and can cause strange behaviour, like not charging whilst turned on or whilst on a call. Similar problems can be found with car-chargers that will not charge until the device is soft reset.
Mike
^no it's not the official charger, I have this usb wall charger called Power Juice (phone and mp3 charger).
Input Voltage: AC100-240V
Output Voltage: 5V
Output Current:1000mAh
Do you think it's because I'm not using the original charger?
fixed my charging problems
The boyfriend told me to try a new cable for my charger so he bought me a 5pin usb cable, tried it at home and it worked! I still need to turn off the screen sometimes but that's ok at least I don't have to turn off the phone anymore. Now my battery charges less than 3 hours.
Hold both SoftKeys and Then press the Power button
Or you can also hold both softkeys and then put your stylus into the reset hole.
answer why it does not charge through the usb
Sorry for the very very late response. Under electrical legislation all hand held electrical devices must be insulated and fused. Some of the chargers that you can purchase are sealed without fuse which indicates that the phone has a fuse contained within its circuitry (or there may be 2 fuses one in each device) .
The problem you have encountered is that you have connected your phone to a computer or mains supply to charge. There has been a surge in the electrical supply either on connection or by un-connecting from these supplies (e.g. connect to the computer as it is booting would see a 65w signal through the USB) and this more often than not blows the fuse which sits on the PCB (printed circuit board) just after the usb connection internally to the phone.
you can either have the fuse fixed for 20/25 gbp or you can purchase a new circuit board or you can use an external charger for the battery. As it is only the power input point that is faulty.
hope this helps
Since we are at this non-charging & battery issue, I would like to ask this question on the D838pro. My battery won't charge even after 24 hours of charging. The red LED blinks thru the whole process. The LED did not turn on to orange or green. It is the battery problem because my spare battery works well. I would like to know what is wrong with the battery as I am willing to strip down the battery. Could it be the battery circuit or wiring that had fired?
cyberdroxxx said:
Since we are at this non-charging & battery issue, I would like to ask this question on the D838pro. My battery won't charge even after 24 hours of charging. The red LED blinks thru the whole process. The LED did not turn on to orange or green. It is the battery problem because my spare battery works well. I would like to know what is wrong with the battery as I am willing to strip down the battery. Could it be the battery circuit or wiring that had fired?
Click to expand...
Click to collapse
Never tried stripping down a battery, some things... well, just don't seem worth it. However as a learning exercise it might be interesting. Without lots of testing on a good battery with a multimeter then I have no clue what the readings should be between all the contacts. (Now there's a little job for you) It is as likely the internal structure of the battery is screwed as it is to be a wiring problem.
If you solve it you can certainly report back here
Mike
when i connect my phone to the charger/ usb cable it does not charge or connect to the pc. woul dthis be a battery problem or a hardware malfunction? also my phone is flashed and i have no battery life left, so i am unable to reflash to the original rom and send it for a warranty.
anyone know how i could fix this?
PS: thankyou in advance
Hi,
i have the same problem. Suddently, my touch dont charge anymore. Connector is dusty but seems ok, the touch boot but low battery. Any idea ? Have you solved this problem ?
thanks
Here is a solution, to send for warrenty, get a new battery from ebay.
Flash to stock rom and 2.x HardSpl and IPL and send back to warrenty.
I did that for mine.
--
Talking about your port, You guys can try to look for parts online and DIY it.
Are you guys sure that it is not the cable / adapter causing problems?
Didy ou try to charge directly using a travel charger (not through PC) and also try another cable another usb port in the PC or another PC
Yeah, i've tryed to plug it directly to AC charger, but without result, and my touch isn't warranty anymore. I'll try to open it but i've to find first the right tool !
I think that it could be a loose or burnt connection in the motherboard or the hardware cables which links to the charging port.
Hello,
I have strange problem, since today I cannot charge my HD while its being on, when I plug in usb charger nothing happens, i tried charging through PC usb port, and nothing happens.
I cannot even establish connection with a pc, don't get 3 choice menu (active sync, hdd, and nothing) on HD when usb is plugged in.
I suspected that the usb port is defected, but when the unit is switched off, it's charging even though there is no amber led on.
It has original rom and radio in it...
Did anybody had similar problem? The phone is under warranty, should I send it for repair?
Thanks in advance.
Very weird. I would definately advise you to send it in for repair. I haven't heard of anything like this before :O.
Good luck!
ICe051 said:
Hello,
I have strange problem, since today I cannot charge my HD while its being on, when I plug in usb charger nothing happens, i tried charging through PC usb port, and nothing happens.
I cannot even establish connection with a pc, don't get 3 choice menu (active sync, hdd, and nothing) on HD when usb is plugged in.
I suspected that the usb port is defected, but when the unit is switched off, it's charging even though there is no amber led on.
It has original rom and radio in it...
Did anybody had similar problem? The phone is under warranty, should I send it for repair?
Thanks in advance.
Click to expand...
Click to collapse
Hi, I got the exactly same issue as you described today. Have you got it fixed?
Looking forward to your response.
Thanks,
This has already been discussed:
Battery Not Charging
1.Hard Reset after backing up data.
2.Check if SPL/ROM mismatch - if U flashed a custom ROM or SPL.
3.Short circuiting pins in battery compartment of HD after disconnecting of power/USB and removing battery. (Don't short the battery - it may explode).
Try the solutions, if it doesn't work then go for warranty.
Too many ppl seem to have this problem and no one uses search
crajee said:
This has already been discussed:
Battery Not Charging
1.Hard Reset after backing up data.
2.Check if SPL/ROM mismatch - if U flashed a custom ROM or SPL.
3.Short circuiting pins in battery compartment of HD after disconnecting of power/USB and removing battery. (Don't short the battery - it may explode).
Try the solutions, if it doesn't work then go for warranty.
Too many ppl seem to have this problem and no one uses search
Click to expand...
Click to collapse
I did search it before and got 8-9 pages of results. I tried all the approaches but none could fix it. This guy described the exactly the same symptom I have so I really wanted to know how he ended up doing with the issue before I sent it off for warranty.
The problem right now is really on the USB connection, even in the boot loader mode, it couldn't recognize the USB but it could do it just one day before.
Thanks for your reply. I appreciate if you could have some new ideas for me to try.
frankw45 said:
I did search it before and got 8-9 pages of results. I tried all the approaches but none could fix it. This guy described the exactly the same symptom I have so I really wanted to know how he ended up doing with the issue before I sent it off for warranty.
The problem right now is really on the USB connection, even in the boot loader mode, it couldn't recognize the USB but it could do it just one day before.
Thanks for your reply. I appreciate if you could have some new ideas for me to try.
Click to expand...
Click to collapse
Have you tried updating your USB drivers?
Have you tried different usb cables?
Some of my usb cables no longer works. I believe my mini usb connector have become slightly looser and I have experienced a cable will charge the phone but won't come up with any options.
Wotth a shot.
The USB driver seems ok since I used the USB connection to flash ROMs and SPLs the day before without any problem.
As for the cables, I tried 5 or 6 total including the stock one but it didn't help.
As stated before, the only time the phone is charging is when I turn it off completely and it charges fairly quickly. However, the bottom (close to the USB end) part of the phone is very hot during the charge. If I turn it on or put it in standby mode, there is no charge or ActiveSync activity.
I have a similar problem.. My phone charges when I plug it in. But I am not presented with any options and ActiveSync doesn´t recognise the device..
same problem here
I am in the same situation. I flashed back the stock ROM, but with no USB, I am unable to put 6.5 back on....any advice is appreciated.
I sent the bad phone (Telstra T8285) back to the seller (an AUS ebayer) and he nicely sent me back a new phone but the story didn't end here. The second phone worked for one day until I plugged in my usb universal car charger. Damn, the exactly same problem happened again at the very moment I pushed in the usb connector. Now I know what the issue has been. I frankly told the seller what happened and he told me what their repair guy found about my first phone, that the fault was from reverse polarity of power supply. I was very surprised because I have been using the same car charger for my previous 3 PDA phones w/o any issues and it's still working for those devices. What's special about the Touch HD?! Does USB have different polarity specs?
Anyhow the seller said he can replace it again but I need to pay the return shipping this time.
What is baffling me is that the phone can still charge when it's off completely but can't when it's on. Does it look like hardware or software problem? Also the USB can't be recognized in the bootloader mode but it could before being faulted by the charger. Does anyone have experience on faulted connector and is there a fix besides replacing the entire motherboard?
Your help and suggestion is much appreciated. Thanks!
The Advanced config Utility has an option for "USB Charging" maybe you could install it and see if the option says yes?
also me... now i figured out what the real problem
i used my old miniusb car charger about one full day before and the same problem start with me with slight different which is charge if i keep it plug in long time...(start charging after 5 min.)
i'm really lucky by not completly dameged
this issued must be listed and get real answer from HTC compeny if the mini usb for hd is different
Hi guys!
Recently I have been using tyting's NexusHD2 ROM and have been having strange charging problems - the phone would charge slowly and inefficiently no matter the battery (I have two original batteries) and the charger (I have two original chargers as well). Yesterday the phone would not charge at all, although there were indications of it - the LED light and so on... I decided to have full wipe by installing the original Windows and I did not have any problems doing it, but the charging problem remained.
What is the problem - it is obviously not faulty USB since I managed to install WinMo, neither it is from the battery or the chargers.
Is repairing difficult (and hence - expensive ) and can it be done by anyone with decent hardware and electronics knowledge? Or should I just buy external wall charger?
Thank you in advance! :good:
JediAndrey said:
Hi guys!
Recently I have been using tyting's NexusHD2 ROM and have been having strange charging problems - the phone would charge slowly and inefficiently no matter the battery (I have two original batteries) and the charger (I have two original chargers as well). Yesterday the phone would not charge at all, although there were indications of it - the LED light and so on... I decided to have full wipe by installing the original Windows and I did not have any problems doing it, but the charging problem remained.
What is the problem - it is obviously not faulty USB since I managed to install WinMo, neither it is from the battery or the chargers.
Is repairing difficult (and hence - expensive ) and can it be done by anyone with decent hardware and electronics knowledge? Or should I just buy external wall charger?
Thank you in advance! :good:
Click to expand...
Click to collapse
IMHO your usb port is faulty even your usb data transfer is still running, but charging is not...
Repairing/replacing your usb port is up for professionals with appropriate tools, skills&knowledge.
bib*oops said:
IMHO your usb port is faulty even your usb data transfer is still running, but charging is not...
Repairing/replacing your usb port is up for professionals with appropriate tools, skills&knowledge.
Click to expand...
Click to collapse
Well, that is odd. I thought it could be the voltage controller in the motherboard. In any case, it seems that is a hardware problem, which sucks...
Hello boys! I have a very serious problem with my LE PRO 3. Since yesterday, the following is happening BUG: When I connect the charger, it does not load immediately. It only loads if I reboot the device. And if I take it out and put it back, it stops loading again. This also happens when I connect to the PC. The device only recognizes if I leave the cable connected and restart. With the headset the same thing. It only recognizes if I leave it connected and restart the device. I'm on the Cydrass Google edition ROM, and my device is the x720 version. I have already switched to other ROMs (LineageOs, Ressuection Remix, and even the Chinese STOCK ROM 26s, and the problem still persists!) Apparently it's a serious problem recognizing my USB port I do not know what else to do! Please, help me!
even first buy , do you have problem ?
To Vitor_147
Remember, if you change the stock original LeEco rom you cannot say "have a problem with my LePro3", it's no longer the original combo "LePro3" (hardware + software) so expect (and accept) anything (better or worse!) and report the defects to the rom developer.
Now some helping things!
Apart to clean the phone usb c port and to try a new usb cable, you can:
With the usb cable connected, switch the usb debug off (or on) (developer options) then check if your computer detect your phone.
Even if your computer doesn't detect the phone or your phone seems not charging battery, if the usb cable (and charger) is good in 99% of the cases it charges the battery even if not at full charge rate (expect a minimum 4 hours charge time).
Before to give up, the last try is to bring your phone back to factory conditions with everything (but everything!) under the exact conditions of how it came out of the factory, then you can start over there and have an idea of whether the phone has a hardware defect or if it's just a matter of software.
I hope you solve the problem, if you find the right solution please report it here, so other users can learn how to solve this problem! Cheers!
orsonbear said:
To Vitor_147
Remember, if you change the stock original LeEco rom you cannot say "have a problem with my LePro3", it's no longer the original combo "LePro3" (hardware + software) so expect (and accept) anything (better or worse!) and report the defects to the rom developer.
Now some helping things!
Apart to clean the phone usb c port and to try a new usb cable, you can:
With the usb cable connected, switch the usb debug off (or on) (developer options) then check if your computer detect your phone.
Even if your computer doesn't detect the phone or your phone seems not charging battery, if the usb cable (and charger) is good in 99% of the cases it charges the battery even if not at full charge rate (expect a minimum 4 hours charge time).
Before to give up, the last try is to bring your phone back to factory conditions with everything (but everything!) under the exact conditions of how it came out of the factory, then you can start over there and have an idea of whether the phone has a hardware defect or if it's just a matter of software.
I hope you solve the problem, if you find the right solution please report it here, so other users can learn how to solve this problem! Cheers!
Click to expand...
Click to collapse
I already wrote this up in Omni thread, so I'll keep it short. I've also been experiencing this same issue for a while now, it first happened on stock rom, reboot solves it. Darko tried a fix in his eas kernel, seems to fix it (so maybe somehow kernel related). I believe it might be somehow related to the usb-c controller, cause I found cases online of similar issues with pixel phones (i believe the controller manufacturer is the same as in our phones). I actually know the exact moment when my problems first began, after I used my OTG adapter to connect a usb mouse. Few hours after that, the phone wouldnt charge.
{Disclaimer - this part is purely my theory}
I think it maybe somehow related to a safety "switch/fuse" of sorts, or something to do with static discharge or something similar, and here's why. I did a loot of trial and error since the first time it happened to me cause it scared the sh*t outta me, thinkin my phone is broken. I am vigilant about careful handling of usb ports and such, (ocd-ish really) so theres no way I physically damaged it, its not loose one bit, cleaned it out, tried wiggling the cable around anyway, has no effect, so I excluded the possibility of a faulty port/soldering. A few occurences to note
No1 - if I plug my phone in the charger first, and then plug the charger in the outlet, it breaks the port, I have to reboot to fix it. But plug the charger in the outlet first, then the cable to the phone - no problem. (Static discharge of sorts?)
No2 - since it started happening, the only way my usb-c OTG adapter works is if i first plug the adapter in the phone, and then the desired usb device in the adapter. If i try to plug the adapter in the phone w/say a usb stick already connected to it - no go, doesnt work.
Oh... I'm sorry for what happens to your phone! It's true the safest way to charge a phone avoiding current surge/spikes/shocks is to plug first the charger to AC outlet, then the usb c plug to the phone, then the usb plug to the charger. If possible, never plug/unplug the charger to/from the AC outlet if the phone is connected to the charger.
When the phone is full charged, first unplug the cable, not important which side first, then unplug the charger. If the phone is still charging, better unplug first the cable from the charger side to avoid micro spikes on the usb c port.
If you cannot obtain a normal behavior of the usb c port neither with reflashing the phone with the "qfil" system, perhaps a logic port of the usb c port is burned or simply in undetermined state, in the last case a total battery discharge may reset the logic port state and the phone can works fine once fully recharged. I'm sorry I can't help you better at this time! Cheers!
Sent from my LEX720 using XDA Labs
@orsonbear, thats my train of thought aswell, micro discharges occuring while plugging/unplugging causing the controller to freak out, or potentially damage the tiny connections (micro usb only had 4 wires vs 24! in usb-c). But I believe the problem lies somewhere on the software/firmware side, mainly because a reboot solves any issue I have. And also I just remembered, the first time it happened to me was a couple of days after I updated my firmware while updating to 19s, or 20s, cant recall precisely. Anywho, for me it's a minor nuissance, not like the OP who can only connect his phone once before rebooting (I can go for weeks before it occurs).
orsonbear said:
Oh... I'm sorry for what happens to your phone! It's true the safest way to charge a phone avoiding current surge/spikes/shocks is to plug first the charger to AC outlet, then the usb c plug to the phone, then the usb plug to the charger. If possible, never plug/unplug the charger to/from the AC outlet if the phone is connected to the charger.
When the phone is full charged, first unplug the cable, not important which side first, then unplug the charger. If the phone is still charging, better unplug first the cable from the charger side to avoid micro spikes on the usb c port.
If you cannot obtain a normal behavior of the usb c port neither with reflashing the phone with the "qfil" system, perhaps a logic port of the usb c port is burned or simply in indeterminated state, in the last case a total battery discharge may reset the logic port state and the phone can works fine once fully recharged. I'm sorry I can't help you better at this time! Cheers!
Sent from my LEX720 using XDA Labs
Click to expand...
Click to collapse
Yes,
I thought about letting the phone down completely, and see if that does not happen anymore!
Same problem here
Days ago it start happen, exactly how you say, i never change the stock software and it start happen randomly, I have to reboot to recognize anything that I plug into the USB c port, I try factory reset and change from 26s to 23s and it keeps happening so maybe I'm pretty ****ed, someone help me, in my country no one will fix the port u.u (sorry for my English).
Hellao! I'm having a very similar issue, charging works fine and the pc detects the phone but OTG and the audio on my headset is not working. Did someone of you find a solution to this problem?
1. x720, x722 or x727?
2. Where did you buy the phones? (Store names)
3. What kind of USB-C cable were you using? The one that came in the box? Have you used other USB-C cables and adapters to see if it works?
This could be hardware failure due to a lack of QCing from LeEco (just your average hardware issue) or a USB-C cable issue. It's ver. 1.0 on all LeEco Pro 3 models (right)? So I can't say it's the cable for sure. Has anyone attempted to take the phone apart to replace the port? do they even sell the port replacement?
Similar problem for me. About a month ago my headset stop working and the phone did not recognize it at all, tried with the adaptor to 3,5 mm jack and did not work either. Charging worked though.
Found a replacement chip with usb c port and ordered. Yesterday i replaced the charging port, but still the headset do not work at all, and connection to PC does not work ether. Charging still works as usual.
I ordered the phone from grossoshop 7 month ago with their rom. Tried this evening to upgrade the rom from 5.8.018 to 5.9.020, still grossoshop but no difference... It should not be a hardware problem as i replaced the type c port.
Should i try to flash another rom to see if there's any difference?
Any other suggestions?
Thankful for any ideas
Linkan78 said:
Similar problem for me. About a month ago my headset stop working and the phone did not recognize it at all, tried with the adaptor to 3,5 mm jack and did not work either. Charging worked though.
Found a replacement chip with usb c port and ordered. Yesterday i replaced the charging port, but still the headset do not work at all, and connection to PC does not work ether. Charging still works as usual.
I ordered the phone from grossoshop 7 month ago with their rom. Tried this evening to upgrade the rom from 5.8.018 to 5.9.020, still grossoshop but no difference... It should not be a hardware problem as i replaced the type c port.
Should i try to flash another rom to see if there's any difference?
Any other suggestions?
Thankful for any ideas
Click to expand...
Click to collapse
Have you tried switching cables? Could you have broken a contact or something while swapping the port out? Have you tried putting the old port back in to see if the computer recognizes the phone with it? Unfortunately you're gonna have to try everything, even if opening it back up again is tough. LeEco phones aren't exactly known for their build quality. Are you x720? Well, flash whatever ROMs you can, I guess. Might as well try everything.
sk8223 said:
Have you tried switching cables? Could you have broken a contact or something while swapping the port out? Have you tried putting the old port back in to see if the computer recognizes the phone with it? Unfortunately you're gonna have to try everything, even if opening it back up again is tough. LeEco phones aren't exactly known for their build quality. Are you x720? Well, flash whatever ROMs you can, I guess. Might as well try everything.
Click to expand...
Click to collapse
Yes, I have tried to switch the cables so no problem with them. Have not done a swap back again as the problem seem to be similar as before, so maybe a change to a different rom will be the next step for me. If change of rom does not work, maybe then I'll try to swap port again.
And yes, It's a X720
Thanks for fast reply.
Linkan78 said:
Yes, I have tried to switch the cables so no problem with them. Have not done a swap back again as the problem seem to be similar as before, so maybe a change to a different rom will be the next step for me. If change of rom does not work, maybe then I'll try to swap port again.
And yes, It's a X720
Thanks for fast reply.
Click to expand...
Click to collapse
Maybe it's not plugged in or attached correctly so the phone doesn't detect it. Sounds like a hardware issue to me, in all honesty. I once took apart my iPhone 5 to replace the non-functional home button and it wouldn't work no matter what I tried. I had to remove the battery, reseat it, and then attach the home button again. It finally worked after a reboot.
just report in on this thread, I as well recently purchased an x727 experienced the similar issue. Basically as described above no matter what roms i test is always have some sort of camera errors when charging.
sometimes charging doesn't work or camera doesn't work I have to reboot to get it to work. extremely annoying. I think it is hardware related.
Anybody else have a solution?
blanktape said:
just report in on this thread, I as well recently purchased an x727 experienced the similar issue. Basically as described above no matter what roms i test is always have some sort of camera errors when charging.
sometimes charging doesn't work or camera doesn't work I have to reboot to get it to work. extremely annoying. I think it is hardware related.
Anybody else have a solution?
Click to expand...
Click to collapse
i got charging problem dude after second day of use just got it last night x727.ffs.
i replace the usb board and the problem persist, i don't know what to do anymore, if someone has passed this problem please speak I am about to smash this damn bugged phone
Anthp said:
i replace the usb board and the problem persist, i don't know what to do anymore, if someone has passed this problem please speak I am about to smash this damn bugged phone
Click to expand...
Click to collapse
This my advice to anybody considering buying this phone don't why you will get zero support from letv.
I got luckey I have zero problems with phone .
I recommend spending more money and getting a supported phone by the maker.
If you do buy one buy it from Amazon where get a warranty on it.
Sent from my LEX727 using xda premium
Somebody fixed thuis allready as my le2 x626 only detects charging by USB when in fact its connected to the AC adapter.
And extremly slow charging from 9 to 100 % more then ó hours.
Also the phone`s microphone is nog working at all!! And the headphone is nog working!
please help