Hello boys! I have a very serious problem with my LE PRO 3. Since yesterday, the following is happening BUG: When I connect the charger, it does not load immediately. It only loads if I reboot the device. And if I take it out and put it back, it stops loading again. This also happens when I connect to the PC. The device only recognizes if I leave the cable connected and restart. With the headset the same thing. It only recognizes if I leave it connected and restart the device. I'm on the Cydrass Google edition ROM, and my device is the x720 version. I have already switched to other ROMs (LineageOs, Ressuection Remix, and even the Chinese STOCK ROM 26s, and the problem still persists!) Apparently it's a serious problem recognizing my USB port I do not know what else to do! Please, help me!
even first buy , do you have problem ?
To Vitor_147
Remember, if you change the stock original LeEco rom you cannot say "have a problem with my LePro3", it's no longer the original combo "LePro3" (hardware + software) so expect (and accept) anything (better or worse!) and report the defects to the rom developer.
Now some helping things!
Apart to clean the phone usb c port and to try a new usb cable, you can:
With the usb cable connected, switch the usb debug off (or on) (developer options) then check if your computer detect your phone.
Even if your computer doesn't detect the phone or your phone seems not charging battery, if the usb cable (and charger) is good in 99% of the cases it charges the battery even if not at full charge rate (expect a minimum 4 hours charge time).
Before to give up, the last try is to bring your phone back to factory conditions with everything (but everything!) under the exact conditions of how it came out of the factory, then you can start over there and have an idea of whether the phone has a hardware defect or if it's just a matter of software.
I hope you solve the problem, if you find the right solution please report it here, so other users can learn how to solve this problem! Cheers!
orsonbear said:
To Vitor_147
Remember, if you change the stock original LeEco rom you cannot say "have a problem with my LePro3", it's no longer the original combo "LePro3" (hardware + software) so expect (and accept) anything (better or worse!) and report the defects to the rom developer.
Now some helping things!
Apart to clean the phone usb c port and to try a new usb cable, you can:
With the usb cable connected, switch the usb debug off (or on) (developer options) then check if your computer detect your phone.
Even if your computer doesn't detect the phone or your phone seems not charging battery, if the usb cable (and charger) is good in 99% of the cases it charges the battery even if not at full charge rate (expect a minimum 4 hours charge time).
Before to give up, the last try is to bring your phone back to factory conditions with everything (but everything!) under the exact conditions of how it came out of the factory, then you can start over there and have an idea of whether the phone has a hardware defect or if it's just a matter of software.
I hope you solve the problem, if you find the right solution please report it here, so other users can learn how to solve this problem! Cheers!
Click to expand...
Click to collapse
I already wrote this up in Omni thread, so I'll keep it short. I've also been experiencing this same issue for a while now, it first happened on stock rom, reboot solves it. Darko tried a fix in his eas kernel, seems to fix it (so maybe somehow kernel related). I believe it might be somehow related to the usb-c controller, cause I found cases online of similar issues with pixel phones (i believe the controller manufacturer is the same as in our phones). I actually know the exact moment when my problems first began, after I used my OTG adapter to connect a usb mouse. Few hours after that, the phone wouldnt charge.
{Disclaimer - this part is purely my theory}
I think it maybe somehow related to a safety "switch/fuse" of sorts, or something to do with static discharge or something similar, and here's why. I did a loot of trial and error since the first time it happened to me cause it scared the sh*t outta me, thinkin my phone is broken. I am vigilant about careful handling of usb ports and such, (ocd-ish really) so theres no way I physically damaged it, its not loose one bit, cleaned it out, tried wiggling the cable around anyway, has no effect, so I excluded the possibility of a faulty port/soldering. A few occurences to note
No1 - if I plug my phone in the charger first, and then plug the charger in the outlet, it breaks the port, I have to reboot to fix it. But plug the charger in the outlet first, then the cable to the phone - no problem. (Static discharge of sorts?)
No2 - since it started happening, the only way my usb-c OTG adapter works is if i first plug the adapter in the phone, and then the desired usb device in the adapter. If i try to plug the adapter in the phone w/say a usb stick already connected to it - no go, doesnt work.
Oh... I'm sorry for what happens to your phone! It's true the safest way to charge a phone avoiding current surge/spikes/shocks is to plug first the charger to AC outlet, then the usb c plug to the phone, then the usb plug to the charger. If possible, never plug/unplug the charger to/from the AC outlet if the phone is connected to the charger.
When the phone is full charged, first unplug the cable, not important which side first, then unplug the charger. If the phone is still charging, better unplug first the cable from the charger side to avoid micro spikes on the usb c port.
If you cannot obtain a normal behavior of the usb c port neither with reflashing the phone with the "qfil" system, perhaps a logic port of the usb c port is burned or simply in undetermined state, in the last case a total battery discharge may reset the logic port state and the phone can works fine once fully recharged. I'm sorry I can't help you better at this time! Cheers!
Sent from my LEX720 using XDA Labs
@orsonbear, thats my train of thought aswell, micro discharges occuring while plugging/unplugging causing the controller to freak out, or potentially damage the tiny connections (micro usb only had 4 wires vs 24! in usb-c). But I believe the problem lies somewhere on the software/firmware side, mainly because a reboot solves any issue I have. And also I just remembered, the first time it happened to me was a couple of days after I updated my firmware while updating to 19s, or 20s, cant recall precisely. Anywho, for me it's a minor nuissance, not like the OP who can only connect his phone once before rebooting (I can go for weeks before it occurs).
orsonbear said:
Oh... I'm sorry for what happens to your phone! It's true the safest way to charge a phone avoiding current surge/spikes/shocks is to plug first the charger to AC outlet, then the usb c plug to the phone, then the usb plug to the charger. If possible, never plug/unplug the charger to/from the AC outlet if the phone is connected to the charger.
When the phone is full charged, first unplug the cable, not important which side first, then unplug the charger. If the phone is still charging, better unplug first the cable from the charger side to avoid micro spikes on the usb c port.
If you cannot obtain a normal behavior of the usb c port neither with reflashing the phone with the "qfil" system, perhaps a logic port of the usb c port is burned or simply in indeterminated state, in the last case a total battery discharge may reset the logic port state and the phone can works fine once fully recharged. I'm sorry I can't help you better at this time! Cheers!
Sent from my LEX720 using XDA Labs
Click to expand...
Click to collapse
Yes,
I thought about letting the phone down completely, and see if that does not happen anymore!
Same problem here
Days ago it start happen, exactly how you say, i never change the stock software and it start happen randomly, I have to reboot to recognize anything that I plug into the USB c port, I try factory reset and change from 26s to 23s and it keeps happening so maybe I'm pretty ****ed, someone help me, in my country no one will fix the port u.u (sorry for my English).
Hellao! I'm having a very similar issue, charging works fine and the pc detects the phone but OTG and the audio on my headset is not working. Did someone of you find a solution to this problem?
1. x720, x722 or x727?
2. Where did you buy the phones? (Store names)
3. What kind of USB-C cable were you using? The one that came in the box? Have you used other USB-C cables and adapters to see if it works?
This could be hardware failure due to a lack of QCing from LeEco (just your average hardware issue) or a USB-C cable issue. It's ver. 1.0 on all LeEco Pro 3 models (right)? So I can't say it's the cable for sure. Has anyone attempted to take the phone apart to replace the port? do they even sell the port replacement?
Similar problem for me. About a month ago my headset stop working and the phone did not recognize it at all, tried with the adaptor to 3,5 mm jack and did not work either. Charging worked though.
Found a replacement chip with usb c port and ordered. Yesterday i replaced the charging port, but still the headset do not work at all, and connection to PC does not work ether. Charging still works as usual.
I ordered the phone from grossoshop 7 month ago with their rom. Tried this evening to upgrade the rom from 5.8.018 to 5.9.020, still grossoshop but no difference... It should not be a hardware problem as i replaced the type c port.
Should i try to flash another rom to see if there's any difference?
Any other suggestions?
Thankful for any ideas
Linkan78 said:
Similar problem for me. About a month ago my headset stop working and the phone did not recognize it at all, tried with the adaptor to 3,5 mm jack and did not work either. Charging worked though.
Found a replacement chip with usb c port and ordered. Yesterday i replaced the charging port, but still the headset do not work at all, and connection to PC does not work ether. Charging still works as usual.
I ordered the phone from grossoshop 7 month ago with their rom. Tried this evening to upgrade the rom from 5.8.018 to 5.9.020, still grossoshop but no difference... It should not be a hardware problem as i replaced the type c port.
Should i try to flash another rom to see if there's any difference?
Any other suggestions?
Thankful for any ideas
Click to expand...
Click to collapse
Have you tried switching cables? Could you have broken a contact or something while swapping the port out? Have you tried putting the old port back in to see if the computer recognizes the phone with it? Unfortunately you're gonna have to try everything, even if opening it back up again is tough. LeEco phones aren't exactly known for their build quality. Are you x720? Well, flash whatever ROMs you can, I guess. Might as well try everything.
sk8223 said:
Have you tried switching cables? Could you have broken a contact or something while swapping the port out? Have you tried putting the old port back in to see if the computer recognizes the phone with it? Unfortunately you're gonna have to try everything, even if opening it back up again is tough. LeEco phones aren't exactly known for their build quality. Are you x720? Well, flash whatever ROMs you can, I guess. Might as well try everything.
Click to expand...
Click to collapse
Yes, I have tried to switch the cables so no problem with them. Have not done a swap back again as the problem seem to be similar as before, so maybe a change to a different rom will be the next step for me. If change of rom does not work, maybe then I'll try to swap port again.
And yes, It's a X720
Thanks for fast reply.
Linkan78 said:
Yes, I have tried to switch the cables so no problem with them. Have not done a swap back again as the problem seem to be similar as before, so maybe a change to a different rom will be the next step for me. If change of rom does not work, maybe then I'll try to swap port again.
And yes, It's a X720
Thanks for fast reply.
Click to expand...
Click to collapse
Maybe it's not plugged in or attached correctly so the phone doesn't detect it. Sounds like a hardware issue to me, in all honesty. I once took apart my iPhone 5 to replace the non-functional home button and it wouldn't work no matter what I tried. I had to remove the battery, reseat it, and then attach the home button again. It finally worked after a reboot.
just report in on this thread, I as well recently purchased an x727 experienced the similar issue. Basically as described above no matter what roms i test is always have some sort of camera errors when charging.
sometimes charging doesn't work or camera doesn't work I have to reboot to get it to work. extremely annoying. I think it is hardware related.
Anybody else have a solution?
blanktape said:
just report in on this thread, I as well recently purchased an x727 experienced the similar issue. Basically as described above no matter what roms i test is always have some sort of camera errors when charging.
sometimes charging doesn't work or camera doesn't work I have to reboot to get it to work. extremely annoying. I think it is hardware related.
Anybody else have a solution?
Click to expand...
Click to collapse
i got charging problem dude after second day of use just got it last night x727.ffs.
i replace the usb board and the problem persist, i don't know what to do anymore, if someone has passed this problem please speak I am about to smash this damn bugged phone
Anthp said:
i replace the usb board and the problem persist, i don't know what to do anymore, if someone has passed this problem please speak I am about to smash this damn bugged phone
Click to expand...
Click to collapse
This my advice to anybody considering buying this phone don't why you will get zero support from letv.
I got luckey I have zero problems with phone .
I recommend spending more money and getting a supported phone by the maker.
If you do buy one buy it from Amazon where get a warranty on it.
Sent from my LEX727 using xda premium
Somebody fixed thuis allready as my le2 x626 only detects charging by USB when in fact its connected to the AC adapter.
And extremly slow charging from 9 to 100 % more then ó hours.
Also the phone`s microphone is nog working at all!! And the headphone is nog working!
please help
Related
Hi everybody.
I don't know, what is going on with my Att 8525.
I bought this earphones for it like 3 months ago, and they do work. I mean, the audio is coming out from the USB Connector.
But, when I plug it to my computer, it does not detected at all. I plug in to power and does not charge. But if I connected back to the earphones, sounds comes out.
I already try to do a soft reset, delete everything, and start from scratch, but it does not wants to charge or connect to Activesync.
If there is someone, that can help me, please tell me.
I'm guessing here, but it seems to me that the constant use of the EXT port (via inserting/removing your headphones) has possibly damaged the EXT port internally (ie dislodged it from PCB). I believe the ports on WM machines in general tend to be a major point of failure due to the physical stress due to insertion/removal
I had a 2.5mm port on my HP rw6828/Atom clone fail on me after using it for a while to connect my headphones.
The thing is, I only used the Headphones one time.
I was at work watching some comedy show on my phone. So battery was running low. I close down everything, disconnected the headphones and connected to my works computer through USB, but then Activesync didnt detected nor the phone.
So i reseted the phone, and try again to connected to the computer and yet still didnt want to connect.
I went home, and tried to connected to laptop as well, and the charger and nothing. It didnt want to charge at all.
So I had to buy a battery charger to charge the battery, that's the only way to charge my phone.
If you have any idea, what's going on, please help me, to resolve this problem.
hey did you get solution to your problem? if yes please let me know..i have same problem except i dint check with ear phones..
teluguone12 said:
hey did you get solution to your problem? if yes please let me know..i have same problem except i dint check with ear phones..
Click to expand...
Click to collapse
If after a hard reset the problem persists then:
As suggested above, it is likely a cracked solder joint on the USB to motherboard OR a bent pin in the phones USB port. Check this with a magnifying glass.
Mike
thanks for reply..do you have any idea where can i fix if it is problem with connection to motherboard
Perhaps if you say the city/town where you live someone might be able to suggest a shop that does repairs without sending your phone away.
Mike
iam in tampa,florida. if you can suggest me any shop that would be helpful..although this is my backup phone i dont want to keep it idle..
teluguone12 said:
iam in tampa,florida. if you can suggest me any shop that would be helpful..although this is my backup phone i dont want to keep it idle..
Click to expand...
Click to collapse
I don't know but does anyone in Tampa know of a shop that does on site repairs?
Mike
thanks...will enquire it..
will the phone charge with the wall plug, or only fails charge connected to computer? I had a problem with the computer once, I just went into device manager and uninstalled the USB hubs, they reinstalled fine afterwards and work great (have to do this every few months, probably because I never use the safely remove crap)
koikaze said:
will the phone charge with the wall plug, or only fails charge connected to computer? I had a problem with the computer once, I just went into device manager and uninstalled the USB hubs, they reinstalled fine afterwards and work great (have to do this every few months, probably because I never use the safely remove crap)
Click to expand...
Click to collapse
no its not working either with usb or wall charger......
Hello,
I have strange problem, since today I cannot charge my HD while its being on, when I plug in usb charger nothing happens, i tried charging through PC usb port, and nothing happens.
I cannot even establish connection with a pc, don't get 3 choice menu (active sync, hdd, and nothing) on HD when usb is plugged in.
I suspected that the usb port is defected, but when the unit is switched off, it's charging even though there is no amber led on.
It has original rom and radio in it...
Did anybody had similar problem? The phone is under warranty, should I send it for repair?
Thanks in advance.
Very weird. I would definately advise you to send it in for repair. I haven't heard of anything like this before :O.
Good luck!
ICe051 said:
Hello,
I have strange problem, since today I cannot charge my HD while its being on, when I plug in usb charger nothing happens, i tried charging through PC usb port, and nothing happens.
I cannot even establish connection with a pc, don't get 3 choice menu (active sync, hdd, and nothing) on HD when usb is plugged in.
I suspected that the usb port is defected, but when the unit is switched off, it's charging even though there is no amber led on.
It has original rom and radio in it...
Did anybody had similar problem? The phone is under warranty, should I send it for repair?
Thanks in advance.
Click to expand...
Click to collapse
Hi, I got the exactly same issue as you described today. Have you got it fixed?
Looking forward to your response.
Thanks,
This has already been discussed:
Battery Not Charging
1.Hard Reset after backing up data.
2.Check if SPL/ROM mismatch - if U flashed a custom ROM or SPL.
3.Short circuiting pins in battery compartment of HD after disconnecting of power/USB and removing battery. (Don't short the battery - it may explode).
Try the solutions, if it doesn't work then go for warranty.
Too many ppl seem to have this problem and no one uses search
crajee said:
This has already been discussed:
Battery Not Charging
1.Hard Reset after backing up data.
2.Check if SPL/ROM mismatch - if U flashed a custom ROM or SPL.
3.Short circuiting pins in battery compartment of HD after disconnecting of power/USB and removing battery. (Don't short the battery - it may explode).
Try the solutions, if it doesn't work then go for warranty.
Too many ppl seem to have this problem and no one uses search
Click to expand...
Click to collapse
I did search it before and got 8-9 pages of results. I tried all the approaches but none could fix it. This guy described the exactly the same symptom I have so I really wanted to know how he ended up doing with the issue before I sent it off for warranty.
The problem right now is really on the USB connection, even in the boot loader mode, it couldn't recognize the USB but it could do it just one day before.
Thanks for your reply. I appreciate if you could have some new ideas for me to try.
frankw45 said:
I did search it before and got 8-9 pages of results. I tried all the approaches but none could fix it. This guy described the exactly the same symptom I have so I really wanted to know how he ended up doing with the issue before I sent it off for warranty.
The problem right now is really on the USB connection, even in the boot loader mode, it couldn't recognize the USB but it could do it just one day before.
Thanks for your reply. I appreciate if you could have some new ideas for me to try.
Click to expand...
Click to collapse
Have you tried updating your USB drivers?
Have you tried different usb cables?
Some of my usb cables no longer works. I believe my mini usb connector have become slightly looser and I have experienced a cable will charge the phone but won't come up with any options.
Wotth a shot.
The USB driver seems ok since I used the USB connection to flash ROMs and SPLs the day before without any problem.
As for the cables, I tried 5 or 6 total including the stock one but it didn't help.
As stated before, the only time the phone is charging is when I turn it off completely and it charges fairly quickly. However, the bottom (close to the USB end) part of the phone is very hot during the charge. If I turn it on or put it in standby mode, there is no charge or ActiveSync activity.
I have a similar problem.. My phone charges when I plug it in. But I am not presented with any options and ActiveSync doesn´t recognise the device..
same problem here
I am in the same situation. I flashed back the stock ROM, but with no USB, I am unable to put 6.5 back on....any advice is appreciated.
I sent the bad phone (Telstra T8285) back to the seller (an AUS ebayer) and he nicely sent me back a new phone but the story didn't end here. The second phone worked for one day until I plugged in my usb universal car charger. Damn, the exactly same problem happened again at the very moment I pushed in the usb connector. Now I know what the issue has been. I frankly told the seller what happened and he told me what their repair guy found about my first phone, that the fault was from reverse polarity of power supply. I was very surprised because I have been using the same car charger for my previous 3 PDA phones w/o any issues and it's still working for those devices. What's special about the Touch HD?! Does USB have different polarity specs?
Anyhow the seller said he can replace it again but I need to pay the return shipping this time.
What is baffling me is that the phone can still charge when it's off completely but can't when it's on. Does it look like hardware or software problem? Also the USB can't be recognized in the bootloader mode but it could before being faulted by the charger. Does anyone have experience on faulted connector and is there a fix besides replacing the entire motherboard?
Your help and suggestion is much appreciated. Thanks!
The Advanced config Utility has an option for "USB Charging" maybe you could install it and see if the option says yes?
also me... now i figured out what the real problem
i used my old miniusb car charger about one full day before and the same problem start with me with slight different which is charge if i keep it plug in long time...(start charging after 5 min.)
i'm really lucky by not completly dameged
this issued must be listed and get real answer from HTC compeny if the mini usb for hd is different
I recently flashed my Defy with 3.4.2-179-2 CEE DEBLUR and it reboots every time I plug in my usb cable. It doesn't matter if it's connected to a PC or to the power adapter. Anyone have the same issue and know of a solution?
I did a google search and found someone complaining of the same issue but didn't see a solution.
More background:
I had an issue with my phone and when I went to do a factory reset I was stuck on the google screen. My power ended up running low to the point where I couldn't run the bootloader. I had to charge the battery manually with a battery charger and some wires. I monitored the voltage throughout to make sure the battery was ok. After flashing the new SBF I found that things worked fine except whenever I plugged in a USB cable it would reset. I put CM7 on the phone hoping it'd help but the problem still lingers.
I will probably attempt to flash another SBF or maybe reflash the existing one.
Does this problem only exists if the phone is fully booted or does it happen if you plug it in while booting also? Because if its happening while booting too maybe your usb cable is broken and theres a short in the cable that makes the defy reboot. Have you tried another cable? And what about plugging the cable in before booting the phone? Tried this already?
I encountered this problem occasionally before. Dunno why.
There's 3 possible issues here apart from software/firmware causes.
1) The USB cable might shorted.
- This can be confirmed by using multimeter to test the usb cable. You will see a shorting between to wire in the USB cable.
2) The Phone USB port might shorted.
- This can be confirmed by using another good/new usb cable and test it with multimeter.
3) Phone battery broken(happened when you charge it using wire and external charger).
- This can be confirmed by trying another Defy battery and charge it.
hi farsight,
upon further inspection i'm pretty sure the usb port is shorted because if i squeeze the bottom of the case the phone will reboot.
is there any way i could fix this? I've looked at some videos for the disassembly of the defy.
hi iregistry,
yes the issue occurs if the phone is fully booted and when it's booting.
quit risky la.. if under warranty, why not claim/RMA?
hi adie, i bought it new on ebay and i'm not sure how the warranty works on that.
[solved!]
after further testing I believe it was because the battery contacts were not as close together as they were originally due to me manually charging the battery. It must have been right on the very edge because it would work normally but just squeezing it would make it lose connection.
I used a pin to push the contacts closer together and hope this solves the issue. I've plugged in the usb and squeezed the case and so far everything seems ok.
IMO this is a poor design on motorola's part. the raised contacts on the phone are nice but the contacts on the battery are poor.
Thank you everyone for responding.
Had the same issue. Your solution worked on mine as well. Pushed the contacts on + and - in, and it worked! Thank you!
I had the similar issue. I had attempted to charge battery with external universal charger and looks like since then this issue where "phone would reboot upon unplugging the power source" started. Now as mentioned in this post, put the +/- pins bit closer and tried unplug and no issue observed so far.
Thanks. :good:
I too have the same issue. I tried to charge the battery with some direct USB.
Today I dropped the phone on my bed from 2' height and it got restart. But its quite surprise to see the effect of the USB plugin with the battery connector loosing up
I am thinking of putting a small alumunium wrapper on the +/- connector. Let see.
It is hard to describe, but I am desperate about this issue as Google/Huawei and Dealer say things that I cannot understand.
With the Nexus 6p I got 2 cables: USB-C-to-UCB-C (similar, symmetric ends) and USB-C-to-USB-2/3 (for the MAC/PC, not similar ends).
I am pretty sure that the issue started since one of the OTA updates, but take it as speculation.
The issue: if I connect the phone to a MAC it starts charging no matter how I insert the USB-C end into the phone itself (let's say the C end has two surfaces - I am talking about ONE end of the cable) BUT when I connect the phone to the wall charger via USB-C-USB-C cable it starts charging only in one particular position of the cable and does not start if I insert the cable while turning one end upside-down (surface 1 - there is charging, surface 2 of the same end does not charge in the same upward position)! The issue appears even if swipe the ends.
If the USB port in the phone was faulty - I would expect the issue to appear with both cables, but the issue appears only with C-C cable. Moreover, I went to the store where I bought the phone and they used THEIR C-C cable with the same issue
They say me: "charge the phone in this position only"! But the idea of USB-C is symmetry, thus I do not understand what the issue is.
Could someone suggest any technical explanation??
is it the wall brick that came with the phone? if so, I would say the brick is bad.
charging works fine here with usb c to usb c and wall brick regardless of how either end is plugged in, even swapping which end is plugged into the brick makes no difference.
uicnren said:
is it the wall brick that came with the phone? if so, I would say the brick is bad.
charging works fine here with usb c to usb c and wall brick regardless of how either end is plugged in, even swapping which end is plugged into the brick makes no difference.
Click to expand...
Click to collapse
thanks for the answer, Unfortunately... the issue is still there with another charger (power bank)... so I am still confused.
Unfortunately, if you have tried every possible combination of cables and chargers and the issue persists, then there must be something wrong with your phone. The only thing I might suggest is to do a factory reset. And if that doesn't work, you'll have to contact support for a replacement. They'll likely request that you try a factory reset before they'd replace it anyhow.
BillyTheRatKing said:
Unfortunately, if you have tried every possible combination of cables and chargers and the issue persists, then there must be something wrong with your phone. The only thing I might suggest is to do a factory reset. And if that doesn't work, you'll have to contact support for a replacement. They'll likely request that you try a factory reset before they'd replace it anyhow.
Click to expand...
Click to collapse
thanks for answer - if I perform a factory reset - will Google Store keep my ownership on Apps I bought? I never did it before and I do not know how to backup the phone as well...
Thanks
Notizer said:
thanks for answer - if I perform a factory reset - will Google Store keep my ownership on Apps I bought? I never did it before and I do not know how to backup the phone as well...
Thanks
Click to expand...
Click to collapse
Yeah you will be able to download all your apps again. The paid ones will show up as purchased in the play store.
murphyjasonc said:
Yeah you will be able to download all your apps again. The paid ones will show up as purchased in the play store.
Click to expand...
Click to collapse
I did factory reset - the charging issue is still persisting. If I understand it correctly only Huawei can check and fix the device. I am so sad I should send the device to them... %( I do not have any replacement at the moment...
Notizer said:
I did factory reset - the charging issue is still persisting. If I understand it correctly only Huawei can check and fix the device. I am so sad I should send the device to them... %( I do not have any replacement at the moment...
Click to expand...
Click to collapse
I was reading your original post again and I agree that it seems unlikely that it's an issue with the usb port if the problem isn't there when you charge with a PC. Have you tried a non Google charger or maybe a custom ROM? It's just a shot in the dark but I would cover all bases before sending it back.
murphyjasonc said:
I was reading your original post again and I agree that it seems unlikely that it's an issue with the usb port if the problem isn't there when you charge with a PC. Have you tried a non Google charger or maybe a custom ROM? It's just a shot in the dark but I would cover all bases before sending it back.
Click to expand...
Click to collapse
The phone is under warranty this is why I won't try custom roms etc. I tried power bank and the issue persisted. For me it is very strange - how the PC cable can provide power no matter how I insert C-end, and the USB-C-USB-C cable works only in one particular way (as I described)...
I am afraid that if I send to phone to Huawei they will not check it (will not turn the cable upside down) and will return it as is...
Notizer said:
The phone is under warranty this is why I won't try custom roms etc. I tried power bank and the issue persisted. For me it is very strange - how the PC cable can provide power no matter how I insert C-end, and the USB-C-USB-C cable works only in one particular way (as I described)...
I am afraid that if I send to phone to Huawei they will not check it (will not turn the cable upside down) and will return it as is...
Click to expand...
Click to collapse
Trying a custom ROM won't affect your warranty. If it doesn't work you can always flash the stock Google image and relock your bootloader before sending it back.
murphyjasonc said:
Trying a custom ROM won't affect your warranty. If it doesn't work you can always flash the stock Google image and relock your bootloader before sending it back.
Click to expand...
Click to collapse
I am desperate... I've got another C-C cable - the issue persists on 2 chargers while connecting the phone (the original and power bank). The power bank charges itself while connected to the original charger via C-C cable (in any combination of connections) , thus nor cable, not original charger are faulty.
What I fail to understand, WHY USB-2/3-to-USB-C charging is working no matter how I insert USB-C end.
In my understanding there is something with usb C-C charging and phone together %(
I do not know what to do... I am sure if I send the phone to Huawei it will come back as "no faults found"...
Finally, I sent the phone to the manufacturer and they found the charging port was faulty - they repaired it and the phone is on its way back.
Thanks for the update
Sent from my Nexus 6P using Tapatalk
Have the exact problem on my N6p. It's been driving me crazy—glad to know I can get it replaced before my warranty expires next month.
I Have the same problem. And now it starting to have trouble charging at all. And I only got the phone for 1,5 months
I have been facing the issue of slow charging from 3 days now. It takes 9-10 hrs to charge completely. Interestingly I just plugged my phone to my PC and USB not recognized pops up every time. I tried changing USB Cables and Chargers , nothing helped. I think these two issues are closely related and some chip is blown up inside. Any idea if what could be causing this?
Use custom kernels
you find the solution ???? please help me if u can !!!
Same issue happened with me when actually Imy phone was bricked,I changed and used other usb cable,then I got solved my issue,then after 3 months,tht cable stopped to work only for my mobile (works in other mobiles still),so I have to keep changing cord n adaptor for fast charging,now iam currently using Moto turbo charging,n from 6 months it's working properly,n never use phone while charging
if pc says that the last usb you plugged is malfunction... than thats the problem with me also.. i guess phone usb port is damage some how... coz my phone also takes 5hrs to charge and pc plug say usb malfunction
You need to get your motherboard change if usb charging board is not seperate. i experienced the sam eissue on my zenfone 5, i did a thourough check, even bought its psu and relaced it. turns out its motherboard was buggy and a slight water drop on the cable mouth caused this issue. better get it replaced if its still in warranty else you will have to buy a new mobo.
jpdmostwanted said:
I have been facing the issue of slow charging from 3 days now. It takes 9-10 hrs to charge completely. Interestingly I just plugged my phone to my PC and USB not recognized pops up every time. I tried changing USB Cables and Chargers , nothing helped. I think these two issues are closely related and some chip is blown up inside. Any idea if what could be causing this?
Click to expand...
Click to collapse
I have same problem you have to change mobile usb charger connector i.e. charging port of mobile. then it will be solved.
Dude do these 3 :
1.check with another adaptor, along with ampere app make sure charging is 2A
2. Change the usb configuration, dont charge from pc it chaarges slow bcoz its DC
3. Change your rom, use custom ones or reflash whatever u r on.