switch on by its self - Sable

hi team
have ipaq hp 6945 fist had problem whith password its solve it but when expart get buck my device its comes whith another problem when i plug the battery on it its starts to boot it its self please can you tell me what is the problem of my device ?
thanks and Regards
Kibanzi

there is a micro -switch on the mainboard that the plastic parts behind the battery cover needs to touch to turn on the device. make sure your battery cover is not loose. hope this heps...

Related

hardware repair-mdaII

Does anyone know of a usa company or person that can repair the mdaII ...the part where the cradel fits in to power and sinyc got loose and then the metal prongs got jamed and are crossed...it happened with the charger in nth car...., the unit is fine.. when i charge the battery and manually put back in ... iam sure i need this piece thats inside the unit... i also want to update to the win05 so i don't loose the info.. thanks

HELP with Trinity- No Switch

Dear Forum
I have a HTC P3600. . Recently I faced a problem to switch on the device. Accidentally the battery has been replaced with another Nokia battery and perhaps the poles are changed and then a red light has appeared for a while. After that moment I can not switch on the device.
There is no Garantie more...
I would kindly ask somebody from the Forum for any idea, about my Problem?...
It's like throwing your device into a bowl of water!
You may have damaged your mainboard...which can't be repared!

Help needed with touch screen

HI
I have a htc shift and the touch screen doesn't work in snap vue and in vista....i tried reinstalling the drivers in vista and no succes..i tried to hard reset snap vue still no succes..i tried anything that i can imagine... the shif is new and the touch screen worked for 5 minutes and after that it stoped..the guys from htc in dubai said that if i leave my htc there it will be ready in 1 month beacouse they don't know what the problem is...and i took it home to see if i figure out a solution..any sugestions??pls help
Maybe the cable connecting the display part to the main part is slightly misplaced.
This connector is aprox. under the keys T, Y, U, try pressing those keys and around them with the Shift turned off.
If that doesn't work, you can try removing the keyboard pushing it from the battery compartment with a straightened paper clip, and reseating the connector yourself.
Good luck.
dproldan said:
Maybe the cable connecting the display part to the main part is slightly misplaced.
This connector is aprox. under the keys T, Y, U, try pressing those keys and around them with the Shift turned off.
If that doesn't work, you can try removing the keyboard pushing it from the battery compartment with a straightened paper clip, and reseating the connector yourself.
Good luck.
Click to expand...
Click to collapse
I tried everything...i got the service manual and looked...and the problem was the display..i went to htc in dubai and they fixed the screen....and now i have another problem...the battery doesn't fully charge..it freeze at 99% and the batt time is very poor even if vista is shut down...the guy's at the service said that they don't know why it's doing this...the batt is ok the charger is ok the mainboard it's ok...and there's nothing left that coud cause this....so i tride reinstalling vista also i tried to charge with all off..still no result...so pls help

HTC is turning off :(

Hello everyone! I have problem with my phone because sometimes is turning off without any reason, I bought brand new battery and is still same when is switched off and I want to put it back on i must take off battery for couple of minutes, then put battery back and then switch on anybody know whats happened?? And how to fix it!!
It's the most standard problem with htc models touch and elf...
This problem is hardware based! in this condition there are only 2 things you can do:
1.send the device to a htc service center and get the motherboard changed for $300+ if you are out of warranty.
2.Or open the mobile and put a piece of thin plastic in between the omap prosessor chip and the steel piece tha goes over it and then put the second cover on top in order to apply pressure to it because the solder pins that are in between the cpu and the mobo are not connecting properly and lose contact so the phone goes off or freezes then goes off and some times stays off. Make sure that there is enough but not to much pressure applied to it! it worked for mine but i did it because it was out of warranty... its a temporary fix but if you are gentile to it after it will surely work for a few more months...
IF YOU HAVE NEVER DONE SOMETHING LIKE THIS BEFORE OR YOUR TOUCH/ELF IS STILL IN WARRANTY DO NOT TRY IT!
I will post a pic that i took when i did mine if anyone is interested... Let me know...
Thanks for reply!
Uff.... first way to fix it is a little bit too expensive! And 2 way to do it seems quite easy, so i try to do it this way Could you add any picture of this and just tell me how to open this phone?
Many thanks!
@Firestarter42
Thanks man!!!!
did what you said, the plastic trik, and the phone is back to life (it was totally dead and didn't charge) you save a life today!!!
I had the same problem untill one day when he didn`t want to turn on and now i do not know what to do with it how to make it work again
Dear Sir,
I have just tried method 2.
My elf didnt have a metal cover on the processor, lol... got it used from someone... or should I say abused? lol
anyway, I hope it works. will update...
here's a link for the demonstrated tutorial:
http://forum.xda-developers.com/showthread.php?t=476152
Thanks a lot again.
I haved the same problem.....and i realize after many times that I didn't change my ipl and uspl!!!so my cocked rom frequentely turn off my device!!!now it's all right!!!!!!!
i had the same problm too....
it kept turning off and just a few weeks ago it would never turn on...
i did try that trick of keeping the plastic thingy on the omap processor ... it worked for a few weeks max after tht it happened as above
finally took my phone to htc.. told them it was gift and i dont have the invoice... actually purchased frm ebay for 150$ .....
they checked it was in warranty,.. they replaced the board... hurray... my elfin is alive again.. and in wm6.1
hope htc fixes this crap issue as many face this problem
My HTC elf was freezing, rbooting and so on, i was thinking that it was a windows/flash/third party programs problems ....
BUT I confirm that the method "open the mobile and put a piece of thin plastic in between the omap prosessor chip and the steel piece tha goes over it"
brings my htc elf to life again ... stable !
(i've done it with a metal piece and not plastic.)
Thanks for the advice !!!!
my elf was freezing and turning off so i try this 2. method and it works, and elf is much faster then before in my case...
I've never had this problem before but this week my phone switched itself off (so had to boot up again) a couple of times. I did try a new custom rom but I've also been using a different charger (USB mains adaptor) and a replacement battery (this seems to be a poor replacement battery which seems to make up the battery level.
So I don't know what was causing it. For some reason, removing the SD card and re-inserting it seems to have done the trick for now but I'll keep watching it.
Hi guys
My phone is, usually at night when there is no use, switching the screen off, the earphone green indicator flashes but the phone will not turn on when I press the power button, I have to do a soft reset each time to get it back on again (even though it appears to be on with the flashing green light). I cannot get calls or text and my alarm fails to sound. Have overslept a few times now!. Also, its battery has gone for a ball of ^&*%. Will this trick help? Thanks a lot!
Turn off as in literally 'poof!' or, it will restart?
The only way to get it to restart is to do a soft reset, or remove and replace the battery. The phone's green light will flash but there is no way to the screen to activate or use the phone - make calls, use the alarm, receive etc. The screen stays black, no use trying the power button either...
Firestarter42 said:
It's the most standard problem with htc models touch and elf...
This problem is hardware based! in this condition there are only 2 things you can do:
1.send the device to a htc service center and get the motherboard changed for $300+ if you are out of warranty.
2.Or open the mobile and put a piece of thin plastic in between the omap prosessor chip and the steel piece tha goes over it and then put the second cover on top in order to apply pressure to it because the solder pins that are in between the cpu and the mobo are not connecting properly and lose contact so the phone goes off or freezes then goes off and some times stays off. Make sure that there is enough but not to much pressure applied to it! it worked for mine but i did it because it was out of warranty... its a temporary fix but if you are gentile to it after it will surely work for a few more months...
IF YOU HAVE NEVER DONE SOMETHING LIKE THIS BEFORE OR YOUR TOUCH/ELF IS STILL IN WARRANTY DO NOT TRY IT!
I will post a pic that i took when i did mine if anyone is interested... Let me know...
Click to expand...
Click to collapse
Thankx your solutions worked out with my HTC Touch and i get replaced omap processor
power problem on Elf (not the usual)
hello guys, i have an Elf T-mobile that someone "lost" i found it, but was bricked...i unbricked following the awesome guides on the forum and installed on it the original italian rom (obviously am not german)
but...here's the problem, when i press the power button (should get it into stand by mode like every pda does) or also when goes on stand by itself, just shuts down !!!
then the pda auto soft resets, until the end...doesn't have the "auto power off problem" like i readed on the forums...however it tried but didn't solve the problem
i think is a problem with the radio, or the IPL or SPL (i tried 1.11.0002 IPL and 1.11.000 SPL...then 2.2x.xxxx IPL and SPL...now i tried 3.14.0002 IPL and 3.14.0000 SPL, also tried different radios...
but the problem remains...
EDIT: Problem solved, changed the little battery in the motherborad, it worked for me
help
Firestarter42 said:
It's the most standard problem with htc models touch and elf...
This problem is hardware based! in this condition there are only 2 things you can do:
1.send the device to a htc service center and get the motherboard changed for $300+ if you are out of warranty.
2.Or open the mobile and put a piece of thin plastic in between the omap prosessor chip and the steel piece tha goes over it and then put the second cover on top in order to apply pressure to it because the solder pins that are in between the cpu and the mobo are not connecting properly and lose contact so the phone goes off or freezes then goes off and some times stays off. Make sure that there is enough but not to much pressure applied to it! it worked for mine but i did it because it was out of warranty... its a temporary fix but if you are gentile to it after it will surely work for a few more months...
IF YOU HAVE NEVER DONE SOMETHING LIKE THIS BEFORE OR YOUR TOUCH/ELF IS STILL IN WARRANTY DO NOT TRY IT!
I will post a pic that i took when i did mine if anyone is interested... Let me know...
Click to expand...
Click to collapse
can any one provide some sought of tutorial for this please
thanks
ishaan_chd88 said:
can any one provide some sought of tutorial for this please
thanks
Click to expand...
Click to collapse
I'm presuming you mean for option 2, as 1 is quite obvious
Anyways, I haven't done this, but I am posting my best guess (untried, untested, just a theory).
Open your phone up and completely dissamble as described here. Completely strip it down so you only have your mainboard. Clearly take all the necessary precautions before hand (backup, etc etc.)
When done, you will see there are blank shields above where the chips will be, if you look, you can see little dimples, you can ease these off here. This will get you into where the omap processor is. You can then put the plastic on top, and make sure it is done as described. Should literally be a case of putting it all together and hoping for the best after that. I will have a look at some point (can't promise when) and see if I can take some photos of where this will go etc.
An alternative would be to try and reflow the joints of solder with a heat gun... very dangerous considering how tight the components are packed in, and overkill.
captainstu72 said:
I'm presuming you mean for option 2, as 1 is quite obvious
Anyways, I haven't done this, but I am posting my best guess (untried, untested, just a theory).
Open your phone up and completely dissamble as described here. Completely strip it down so you only have your mainboard. Clearly take all the necessary precautions before hand (backup, etc etc.)
When done, you will see there are blank shields above where the chips will be, if you look, you can see little dimples, you can ease these off here. This will get you into where the omap processor is. You can then put the plastic on top, and make sure it is done as described. Should literally be a case of putting it all together and hoping for the best after that. I will have a look at some point (can't promise when) and see if I can take some photos of where this will go etc.
An alternative would be to try and reflow the joints of solder with a heat gun... very dangerous considering how tight the components are packed in, and overkill.
Click to expand...
Click to collapse
thanks man but i guess am so dumb that am not getting where is this processor located anyways currently my phone is working fine but in few days I'll get the tools & open it...let see than
if you can arrange any pic of processor(where we have to fit plastic) it will be extremely helpful...
anyways thanks for helping
tc
where to get small battery on mother board

Replaced the digitizer, Smartphone only boots when not in housing

Hi guys,
hopefully somebody can help me with the problem I have with my beloved HD2. I've successfully replaced the digitizer within my HD2. My problem is though, that the phone only boots when it's not in its housing. When I take the mainboard out of the phone's housing, the phone boots just like it should. But as soon as I put the mainboard back in, the phone doesn't boot, it only vibrates and then shows a black screen (with the backlight turned on).
Any ideas on this? I'm kinda desparate right now . Any help is highly appreciated.
Thanks in advance
propably bad used screen without scratches! happened same.. just digitizer dont working when in housing..
HD2
HD2 the best of the best
May a bad cable connection be the reason?
Or a slack joint?
- Discover "Bosnian Pyramids" on you smartphone and tablet devices;
hi
hi i too have the same problem i spent 3k to change its display and touch pad and now he sasys theres a problem with a strip and demanding 1k . now i feel like thrashing the phone . dies any body know the solution for this ... it boots magldr and then showsup android logo and restarts this is what it happens continuosly

Categories

Resources