Hi! i've bought an used Qtek 9090. the problem is that this Qtek don't power on! it doesn't go on bootloader mode, doesn't go on hard reset ecc... but when i charge it, the red led turns on!
what can i do? please help me
well try to charge the battery only in the cradle
if this not help try to borrow working battery from someone, if your device does not start even with working battery then you are screwed (a hardware problem of some kind)
no i think the battery is ok.
there is a way to restore the bootloader? i've read about the jtag, but i don't know anything... can you explain?
Battery is charging only when the LED is orange/amber. Red means problems with charging - that's why xplode proposed putting the baterry directly in the cradle, as it can "fix" the battery.
Well the red light means there is problem, the most comon problem is the battery, but the red light is also shown with motherboard, bootloader, kernel, and other problems
one more option is there. if the battery is not charged from a long time it needs a shock before recharging to activate the electrons. u should apply some 12v at 1 or 1.5 amp for 15-30 sec. than battery will get a little charge which is sufficient to turn on the phone once.................... but do not apply this voltage regularly or for long time.
Related
got an spv m500,i think its the same as the old xda mini?
it will only power up when the charger is plugged in,but only stays at the windows logo screen which also displays the rom details etc.
the charge indicator doesnt light up either!
any ideas?, could the battery be duff!
Well if the battery doesn't give out power, and the charge indicator doesn't light, then its probably safe to say that the battery is gone. But there is the possibility that your USB charging port is faulty - which might need a bit of solder work.
As for the ROM not starting up, how long have you waited? Some ROMs, especially BigStoraged ones, can take up to 10 minutes on their first start. If it still fails to start, a reflashing of the ROM might be in order - though you can't do this with a dead or not-so-good battery.
hi ive tried this:
"Problem 6: Device doesn't turn on, shows red LED only
In this case you can try:
Remove battery
Connect Hermes to charger or USB
Insert the battery while Hermes is connected to charger
Red light should turn Amber
Soft Reset "
but i dnt get any lights coming on it was working last nyt and i took a call after the call finished i put it on standby and i went to use it 20 mins later and it wasnt turning on ive done a soft reset nothing happened, cant do a hard reset and the above witrh the charger or usb didnt work anybody know wat might hav happened i havent done any upgrades its a standard m3100 from orange
mrcopyright said:
hi ive tried this:
"Problem 6: Device doesn't turn on, shows red LED only
In this case you can try:
Remove battery
Connect Hermes to charger or USB
Insert the battery while Hermes is connected to charger
Red light should turn Amber
Soft Reset "
but i dnt get any lights coming on it was working last nyt and i took a call after the call finished i put it on standby and i went to use it 20 mins later and it wasnt turning on ive done a soft reset nothing happened, cant do a hard reset and the above witrh the charger or usb didnt work anybody know wat might hav happened i havent done any upgrades its a standard m3100 from orange
Click to expand...
Click to collapse
The problem appears to be caused when battery has more or less zero charge and perhaps fooling the charging circuitry into not recognising a battery is in place.
So - Force charge the battery without the Charger
If your problems remain you could always try the following to manually charge the battery a little (enough to let the Hermes know the battery is present when you put it back in) credit for this goes to triposte as the following is adapted from his suggestion:
Those with a basic knowledge of circuitry and things technical will fair better with this solution. The electrical contacts are all important, poor contacts will render this a worthless exercise.
I leave it to you to decide how you connect the wires. If you have no other means you could enlist the help of someone to hold the batteries and wires together while you connect to the Hermes battery!
1) Remove the battery from the phone!
2) Take 3 fresh AAA batteries in series (total 3 x 1.5V = 4.5V)
3) Connected the (+) wire to (+) on the battery
4) Connected the (-) wire to (-) on the battery
5) Hold this in place for 60 seconds.(possibly longer you are trying to charge it enough for charging circuitry to recognise there is a battery installed.)
6) Put the battery in your phone
7) Switch on phone and start charging (via USB)
Hopefully you will get the Amber charging light.
It may be worth repeating this a few times if not successful on the first try.
Warning - Do not connect a mains based transformer to the battery with an incorrect charge rate (mAh) and voltage (V). Any attempt to force charge using mains transformers could be extremely hazardous (explosive). Only a qualified/competent person should attempt to charge the battery in this way. Similarly, even if you are using batteries to do this task, do not leave them connected for more than a few minutes and stop immediately if either set of batteries become warm.
If the problem persists it is worth re-trying the solution you mentioned in your post as well as the above, before giving up.
The final resort - a new battery.
Mike
hi ive tried wat you hav asked but still not red light or amber ligh it shws no light at all i dnt understand how its gone from working 1 minute to completely not working in another
mrcopyright said:
hi ive tried wat you hav asked but still not red light or amber ligh it shws no light at all i dnt understand how its gone from working 1 minute to completely not working in another
Click to expand...
Click to collapse
Yes, I know. It has been reported by quite a few and is actually quite a common problem (relatively speaking) across several phone brands and types.
The solutions you have tried have worked for some, not all. One or two found that it randomly (seemingly) just started charging again.
Your problem is whether to return the device as defective (hopefully under warranty) or whether to chance just getting a new battery. A battery will be fine if it is the usual battery problem, but if not then you'd have wasted money. If you have access to a retailer where you could access a battery just to test it that would be ideal.
Mike
I seem to remember having the same (similar?) problem on my old Universal - I think the solution in that case was to take the battery out for 10 minutes, then put it back in and then connect the phone up to the mains charger, rather than to the USB connection on your PC. The phone needed to be left off (not difficult with a completely flat battery ) and then seemed to charge....
Just a thought, not sure if it's been tried in this case?
Mark.
Mine is Cingular 8125
I flashed RUU_Prodigy_1060701_101_11310_QTEK_WWE_Ship to get IPL/SPL 1.06 and Redio 1.xx (I don't quite remember it).
then I flashed WM6 roms 5.2.1921(build 18521) which does not involve IPL/SPL and Radio.
Everything seems normal.
I leave it charge for all night, I saw 100% this morning, but the it drop to 50 after half an hour, and completely died after 1 hour.
I cannot recharge it when the phone is off, all lights are off, no flashing.
of course, I cannot turn it on.
Few days ago, when I was using WM5 with IPL/SPL 2.26, I can charge the battery, and I can use the phone with GSM and Wifi on for at least one day without recharge.
Need help, thank you.
Please Email me: [email protected]
I solved me problem with an universial car charger for variable voltage.
This charger is not for this phone, but it for many other things, such as PSP, Radio, etc.
I set the voltage as 4.5V, and I use two wires to take over the electrisity from + and - to the back of my phone.(there are a + sign and - sign on the battery), I hooked on the phone's + and - brush, and use this universial charger bootup my phone, then put on the battery, the battery would be charge for a little while, and enough to do another boot.
Dont use this method to charge the battery, it may burn your phone. and dont use higher than 4.5V for first bootup.
the same problem with you.the battery seems not so stable after I flash wm6 rom
PLease help me
I have a similar problem one night i was charging my cingular 8125 then after i wake up i look my cingular and it dont turn on!!!!
I put again to charge and it make the led red and if u leave the battery the red led continue, please help me!
Same problem but solved somehow
Same thing happened to me and I somehow solved it. It is not normal for a battery to suddenly drop dead. The problem is I think the battery has 2 cells inside and sometimes one is charged and the other gets stuck uncharged when the battery is old.
What I did is:
drain down the battery fully until the phone does not turn on any more. So the two cells get ballanced at 0 charge.
Plug in the official wall charger when the phone is off.
Press the turn on button. So it charges a little while phone is off. Wait 1 minute
Press power button again to turn the phone on, and leave it on until (if at all) charges to 100%.
Just my experience maybe it will work for you too. Worth trying! Correct me if i'm wrong ... good luck
Help....seems that my Magician is dead....making a long phone call (1 h) after call end, display switch off and Notification led become fix Blue (bluethoot was off) and then i try to hard reset. Led switch off and no results. I try then to put the power supply cable and the led become RED.... !!! (neve seen red.....) pda is not switching on anymore...any details on the reason of this RED light ???....please.....
thanks in advance
Red LED means the battery isn't connected or the device can't charge.
Try taking the battery out for a few hours and try to switch the device on again.
My brother in-law had the red LED issue too, we solved it by 'kick starting' the battery with two wires and a 9v battery. (At your own risk of course).
Good luck!
helterskelter said:
Red LED means the battery isn't connected or the device can't charge.
Try taking the battery out for a few hours and try to switch the device on again.
My brother in-law had the red LED issue too, we solved it by 'kick starting' the battery with two wires and a 9v battery. (At your own risk of course).
Good luck!
Click to expand...
Click to collapse
Red Led doesn't mean that the battery is not connect with the device. It simply means the cover is not properly intact. Try taking out the battery off the device, put it back in the slot. Place the cover carefully and completely. And then connect the device to AC power supply. It would definitely come *alive*
still dead....grrrr
so cover is ok...it seems to be properly fixed, even the smal swithch that create some unwanted crash few months ago is now working properly...
i made a 1 h long phone call with battery and charger (usb from pc) and after line felt down, bluetooth led blue on (was off) and screen with phone but no changement by touching it. so switch off by power off and ...dead...now without battery but with charger (or usb from PC) RED led on. With batttery AND charger RED on, and with battery all dead. i cannot reset anyhow with or without battery /charger....need it...sh*t.....(ops...sorry)
thanks a lot anyway....
omino_ribelle said:
so cover is ok...it seems to be properly fixed, even the smal swithch that create some unwanted crash few months ago is now working properly...
i made a 1 h long phone call with battery and charger (usb from pc) and after line felt down, bluetooth led blue on (was off) and screen with phone but no changement by touching it. so switch off by power off and ...dead...now without battery but with charger (or usb from PC) RED led on. With batttery AND charger RED on, and with battery all dead. i cannot reset anyhow with or without battery /charger....need it...sh*t.....(ops...sorry)
thanks a lot anyway....
Click to expand...
Click to collapse
what I will suggest is, you should get a new battery instead!!
Got the same problem now!
Both my wife and me got a Magician. Hers is dead now - same symptoms.
First guess was dead battery as well. But I exchanged it with mine fully loaded. No difference!
Usually when you plug the powercord into the device orange flashes up and device boots. Here nothing happens.
I'll have some electrician have a look at both. Maybe he can find the fault by comparison. But I don't expect a lucky outcome.
on back side of ur device when u remove the battery cover, u see a small black switch on the right side just next to the battery.
put the device on charge..with cover off---it will show red light contunuously on.
now manually press gently that black switch and see if ur device starts to charge.
if u see a yellow light any point of time doing this u may have to get this little switch repaired or do a temporary work urself by kepping it at place manually bu something.
try and tell
Now it works!
I think we all knew about that little switch. But thanks for your thoughts.
Anyway, hers is running again!
Two days ago I took it fully apart. No obvious fault noticeable. I left it the way it was now to prepare it for shipping. Today my wife asked me I should try it just once again. So I held the battery on the connector and plugged the USB cable and then: it booted!
But the internal battery doesn't seem to recover. It stays at 0% (1h "charging" since then).
I have to correct myself: Even the internal battery is charging (but it takes its time).
my magician is also dead and just the red LED is burning when i put it in the USB! Can anybody help me?
Still ned solution!
Can some one who was having the same problem help?
your device battery detector switch(little switch) is broken or logged-out of Main Board.
when it broken,the red LED is on at all.
it is the greatest weakness of magician...
z_qz54 said:
your device battery detector switch(little switch) is broken or logged-out of Main Board.
when it broken,the red LED is on at all.
it is the greatest weakness of magician...
Click to expand...
Click to collapse
i am opening my jam case,bring the switch out and conecting sides of switch by a piece of wire.now a day there no problem with openning the battery case or.. but my WM cant recognize the battery level.it's alway 0%.and even the charger is connected no orange led i can see.but the charger charge the battery and battery works for more than one day!!!!!!!!
any one with the same problem!????
or any one having solution!
REGARDS
I'm gettingn red led light too when charging from wall outlet. Charging from usb is fine. a weird thing is when my battery came down to 50%, imate jam will shut down and won't successfully reboot. some people from this form mentioned it's an indicator that the battery is dying.
Hi i have a problem. Yesterday my Prophet battery goes to 0%, when i back to the home I plug-in it to charger. The light-emitting diode start flashing, but i can't turn on my phone. After 8 hours connected to charger Prophet still won't work. DO you have any idea? Maybe this is battery problem?
PS. Sorry for my poor english.
same with me,my dopod 818 pro won't turn on after 2 month not use,i try to charge,but the led not light..its off..i have no idea witn this problem,please help me to solve.thanks
Same problem with my Prophet.
After 3 month of no use wont charge and wont go on, no light of chargin nothing.
Is the orange light on when it is plugged into power without battery???
Any one solve this problem????
Thank you
UPDATE
I open the battery and fill it with 3,5V directly on battery inner contacts for few minutes
( directly on battery contacts red + and black - and I control it with multimeter to see how the voltage rising up. )
After aprox 3 minutes I try to power it up.
AND IT WORKS!
I put it on charge and the orange light went on and strat charging the battery. The phone now works.
So it is the battery issue. ( Last night I put it on power over the night and nothing no charge at all, what a stupid system )
errhec said:
Same problem with my Prophet.
After 3 month of no use wont charge and wont go on, no light of chargin nothing.
Is the orange light on when it is plugged into power without battery???
Any one solve this problem????
Thank you
UPDATE
I open the battery and fill it with 3,5V directly on battery inner contacts for few minutes
( directly on battery contacts red + and black - and I control it with multimeter to see how the voltage rising up. )
After aprox 3 minutes I try to power it up.
AND IT WORKS!
I put it on charge and the orange light went on and strat charging the battery. The phone now works.
So it is the battery issue. ( Last night I put it on power over the night and nothing no charge at all, what a stupid system )
Click to expand...
Click to collapse
Oh.. great! do you know which pin of the battery is (+) and which pin is (-) pole? I want to charge the battery by a balance charger.
happened to me couple months ago
and i used desktop charger for 5 minutes directly on the battery
then plug it in and charged normally with usb connector
used the desktop charger on the first and last pins on the battery
Hello, i'm sorry, my english is bad. but i wanna help.
Now, before 1 week i have the same problem, my qtek s200 after update whit wm6.1. OK 1 month everything was ok, but after that /i don't now where i go wrong but no matter/ that my phone start stuck in bootloader. I let it one night on to see, maybe will turn,and at the morning he wont start, even the light wont start wen i put the carger on. I take one charger/from sony erricson/ cut cable, there are 2 cables, take off the battery of my pda, put directly cables from sony charger in to battery, black is minus, red is plus, but don't worry, there is no problem if you make mistake.Let it like that 1-2 hours, put battery back on pda and everything will be OK.Now in my case my ROM fu** up, i go to tree color screen/see more info how to do that/ and replace the ROM.and next time do not full dry the battery.Hope i help.