Database Users

XDA Exec, STUCK ON SPLASH SCREEN

Ok, Ive got a new problem with my XDA Exec.
Opened it up and tryied to turn on the backlight and nothing. tried a soft reset, nothingtried a hard reset now it just sticks on the splash screen, the red writing comes up on the right and side and just hangs there forever!
Please help

You're stuck. apparently the only remedy is turning it in to repair. For most of us it is under warranty.

Just off the phone to 02. Theres sending me a new one via courier on monday. it's less than a day old.
Is this a comon fault with the Exec?

erm ... I managed to experience this problem.
I was trying to uninstall SPB GPRS thingy that comes with the O2 package, and it just wouldn't go. I ended up deleting the program files and getting an error when it started up, so I deleted the GPRSNotify file under Startup. It never worked again ...
I got the splash screen, tried soft and hard resetting and various permutations (including standing on one leg and while holding breath) ... nothing. Did try to install fresh ROM, but startup wouldn't get far enough to let PC load ROM over USB.
Ended up contacting O2 who sent me a nice shiny new one, as it was only three weeks old. This time I haven't installed GPRS monitor thingy, and I don't intend to fiddle with it again ... or at least until I've forgotten my lesson ...

Sorry i ment to give you guys an update on this. I did manage to get it working again, although i still accepted the new one the sent to me.
What i did was installed a new rom off the 02 website. at 1st the computer couldnt see the phone so wot i did was enter what i think was the programming side of the phone. i found the instructions on how to this on the net. i think i pressed the 2 soft keys and the light switch while pressing the reset switch with the stylus (i think that was the buttons but unsure as i cant find the page again) when the screen light up again there was some faint writing on the screen with the word serial or usb. Double clicked on the rom file and 30mins later my phone was revived.
Funny it was the gprs monitor that i too installed before the phone screwed up? ive since installed it again on the new phone and have had no problems with it since.

trickydickyd said:
I think i pressed the 2 soft keys and the light switch while pressing the reset switch with the stylus (i think that was the buttons but unsure as i cant find the page again) when the screen light up again there was some faint writing on the screen with the word serial or usb.
Click to expand...
Click to collapse
Otherwise known as Bootloader mode

Aye, thats the one.
Cheers

Locked up, please help

Hi,
I have a tmobile MDA (wizard). I attempted to install some software on it, but disconnected and rebooted before it was complete (it appeared to be just spinning).
Now after a soft reset, screen shows only 'Windows Mobile' after booting, and none of the buttons work and I can't advance from this screen.
Is there a way to hard reset that doesn't involve using the OS (ie, I can't click on anything because it's not getting to that point).
Also in this state activesync isn't detecting device.
Thanks in advance! - Chris

Hold down (and keep holding) the camera button while depressing the reset button. Hopefully it boots into a tri-color screen. If so, plug it into the USB port and, at the bottom of the screen, it should display "USB". If that happens, flash it with a *known good rom*, such as a stock T-Mobile rom. Don't try to be clever, the object is to get the phone working. Once the flash has started, *get up and walk away* for 15 or 20 minutes. Don't check in on it, leave it alone, It takes some time. When you hear it's little chime, it's done, rebooted and ready. If any of the above doesn't happen or the flash outright fails, then you may have trashed it permanently. It doesn't sound like it's beyond hope yet, however.

i have the wizard and im having the same problem after installing a ROM from this website...it just goes to the windows mobile screen with the numbers then shuts off...id really like to save my phone is there anything else i can try because that hard reset thing isnt working

axxeman001 said:
Hi,
I have a tmobile MDA (wizard). I attempted to install some software on it, but disconnected and rebooted before it was complete (it appeared to be just spinning).
Now after a soft reset, screen shows only 'Windows Mobile' after booting, and none of the buttons work and I can't advance from this screen.
Is there a way to hard reset that doesn't involve using the OS (ie, I can't click on anything because it's not getting to that point).
Also in this state activesync isn't detecting device.
Thanks in advance! - Chris
Click to expand...
Click to collapse
Well same thing happened to me a few days back.. I had to Cold Reset [which restored it to factory defaults], but hey I got it working again..
Press Communication Button [Top Left] and Record Button [Top Right] at the same time and use the stylus to soft reset..
You will get a black screen, asking you to press "Send" to reset to "Factory defaults"
Press "Send".
Hopefully you should get your MDA working again ...
I read the "Above" in the HTC Wizard Service Manual [PDF] on the *last page* under the "Cold-reset" Section..

TOTALLY DEAD Htc Tytn

Hey everyone,
Firstly this is my first post and so I am not quite sure whether I am posting in the right place. Accept my apologies if I have made a mistake. I own a Htc Tytn which I purchased this January 2007. I read in several forums that some users are experiencing certain problems with the device like screen allignment etc. I was very glad to find out thart my device was a very stable one. Surprisingly it never froze. I did perform some soft resets at times just to ensure everything stays all right. I also did not have any keyboard or allighnment issue. Today when I was speaking on the phone suddenly my Tytn shut down. When I restarted it the screen went white. Firstly I tried performing a soft reset which didn't work and then a hard reset which didn't work as well. Then i thought of entering the bootloader mode so that I can install the ROM again but it wouldn't go into the boot loader mode ( I did press the right sequence of buttons for the hard, soft reset and for entering bootloader mode). Even the htc logo doesn't appear. Whenever the power button is pressed the screen goes white. Also whenever I tried the different reset and tried entering bootloader mode the screen went white as well. My device had almost full charge when this happened. Also one more thing, as the screen goes white the green button( send/ receive)button blinks( weird!!!!) but the red button is not lit and doesn't blink at all. Lastly I think I have made it clear that I was not trying to upgrade the ROM or anything when this disaster happened. I WOULD reaaallly appreciate if somebody could help me sort this problem out with my Tytn before I am forced to send this device back to HTC for repair( which I don't want to). Thanks everyone.

Check the TyTn Wiki:
http://wiki.xda-developers.com/index.php?pagename=HTC_Hermes
There's a section in there on the solid white screen, phone doesn't boot. I think it's in the "Common Upgrade Problems" section but the advice there may be applicable to your situation. Good luck!

Wizard is Frozen - It won't start. Someone help pls??

Hi, I would really appreciate anyones help with this. My brother went on holiday and left me his 02 XDA Mini S (I found out here its also called a Wizard?), and I had no problems using it for about 3 days - was just testing the various features.
I found my brothers contacts - and since its now a hand me down so I wanted to remove all these etc - I asked my brother what to do and he said do a Hard Reset. I found out in the Manual how to do it - I press the Communication Button and the voice command button and use the reset and nothing happened. I asked my brother and he said use the communication and voice button and then turn it on, that sometimes works - and it did. The screen showed:
Press Send to restore factory default...
I pressed the send button and it said it formatted. I was happy, it turned on, I did the set up - everything was working. Then at the end of the day I turned it off and in the morning I turned it on - all the screen shows now is the screen which first comes on - 02 with and underwater bubbles thing, and four lines -
IPL 2.21.0001
SPL 2.21.0001
GSM 02.07.10
OS 2.21.4.1
in red.
It won't go to the next screen - which I think says windows mobile. It just stays at the first screen when I turn it on - and has these four lines
Can anyone help me please? My brother will be back from holiday soon and he will be very upset with me if he finds I ruined his phone
please please please help me - i'm not as good with technology as you guys
Jocelyn

Try and get into bootloader mode by holding down the camera button and soft resetting your device. From bootloader mode you can flash back to the factory rom that was on the phone or wizard love.

Hi
I found how to go into Bootloader mode - my phone now shows three colours. But I'm not sure how to do the rest you mentioned. Could you explain how I should do it step by step please? Sorry!
Jocelyn

He means that you download the orginal rom from your provider and flash it back onto the phone.

Ok
I have made no progress
Here's what I did (please don't laugh - I'm new at all this)
1. I downloaded the active sync software from microsoft, and also downloaded a file i searched through on the forum mentioned by peter, called Wizard Love.
2. I pressed the camera button and soft rest the wizard to go into boot mode
3. I ran active sync - it said no connection.I connected the Wizard and searched - it said that no device was found (but the computer made a sound like it always makes when USB is plugged in). Also on the phone, it showed the word USB at the bottom left of the screen.
4. I extracted the wizard love and double clicked on the file newromupdateutility_wizard_noid.exe
5. When I got to the screen about existing software on the phone it was blank in that section, but it had the option to use the new one, so I proceeded.
6. The Wizard screen switched to a bar and completed 100% within about 5 minutes. Same thing on the computer screen.
7. It shows congratulations - etc.
8. I clossed everything and shut off the computer. Disconnected the wizard and there was a picture like some love cartoon characters - and thats all.it just stayed at that screen for a long time. Finally i thot maybe i should turn it off, but the power button does not work.
9. I used the stylus and did it a soft reset - the phone still froze at the start, with a wizard love cartoon - but the 4 lines i mentioned in my first post were different - it showed different numbers. But it still stuck there.
10. I thought maybe the wizard love is not compatible with my phone? So I went to the 02 XDA mini site, and downloaded the software from there - Xda_Minis_Upgrade_v2.21.4.101. I redid the whole thing, this time with this software.
11. At the end I saw Congratulations! again, but this time the screen had gone back to 02 - and the numbers went back to what was in my original posting. But still the phone does not start - its just stuck at that 02 screen with the 4 red lines.
12. Somone help me please!!! Have I made it worse???
Jocelyn

The Love ROM should work on your phone since it it does not have IPL/SPL (AFAIKnow). However, it seems that the phone itself already have a bit of problem itself. Using the "Xda_Minis_Upgrade_v2.21.4.101" to flash the phone in bootloader mode is the wise thing to do. Probably you'll need to hardreset it again (i.e. what you've done in the very first post).
As far as I can see, you've did nothing wrong on your first post. It seems to be the phone problem. ANYWAY, you may want to note the little issues. Example, do not have the miniSD card in the phone when doing all the stuff said above.. and possible, remove the SIM as well.
Also, sometimes, it takes ages for it to boot up. I'm not sure how long you've waited, but I would say.. give it a good 5 mins to do its bootup to confirm it hanged.

Sorry
I should have mentioned - in both cases when I ran the utility, once I waited at the splash screen for more than 10 minutes and nothing happened, i just tried to do a hard reset. In both cases the words came up, press send to do a reset etc...
but when I press the left (green phone) button (i think that is the send button?) it says format failed everytime.
I searched at some other thread and followed what Zabardast_1 says about flashing and I tried that, it does not work. Is there any other option? Oh i also tried it another time, this time disabling Anti Virus first - but still no luck
Jocelyn

Hmm.. I'm sorry to tell you. Since you have a 'Format fail', you 'officially' have a bricked device. That has something to do with the hardware.. or stuff that doesnt have any thing to do with your flashing.. probably CID unlocking may cause this problem.
ANYWAY, it seems that your only choice is to get it to somewhere to have it fixed. probably you want to make it as official (i.e. use the O2 ROM) before taking it to O2 to have it fixed.

Stupid Problem with P3452

Hi all
first post and i got an interesting problem with my phone which i qualify as stupid. It all started when when my virtually keyborad started becoming unresponsive and when i tried to do a factory reset, i could not enter the 1234 number to start it. i left the phone for a while and then i could not get into the setting even . But i could receive calls but i could not call since i could not access any numbers on the dial pad( by pressing on the numbers of coruse but from dial log screen i could)
Anyway long story short while fiddling with the phone , i thought the lock feature was on that is why some of the touch functions was not totally responsive but to my sadness, i activated the lock and now the phone is stuck on the front page and i cannot access anything since i must press unlock at the far corner of the down screen but stupidly, while pressing on the unlock, since it is unresponsive, i cannot unlock the phone to get to the normal menu and so on.The only thing working is the square pad which tells me to press cancel then unlock to free the phone for normal use
By the way the lock feature is the one that blocks the phone so that you do not accidentally press on the touch screen and activate a program and not the lock thing operators put to limit your phone
I want to know if anyone can help me unlock the screen so that i can reset the phone or alternatively any other method via usb to reset my phone to factory settings. Any special buttons on the phone i can do to do that?
I tired leaving battery out for 24 hours but that did not work to unfreeze the touch buttons
Was thinking to reload the windows mobile completely via the micro card (which i read here) but i am not sure it will work or i fear it might brick my phone
Any suggestions will be welcome please.... thanks

Use myMobiler to control device from Pc through usb
Good luck
Ps: you'll probably have to change digitiser afterwards

Well tried the mobiler but the thing is that it asks the phone to allow the program to conenct and i cannot press yes on the touch screen since it is frozen or something so i am stuck again.

Very strange, it doesn't ask anything on my device...
Why don't you hard reset: press green and red buttons and while pressing, poke the stylus shortly in the reset hole then release the 2 buttons. It will ask something that you probably won't see, just press the action button and wait for it to restart.

Don't flash another on just yet - it may well cause issues as it sounds like your digitizer is broken. Don't hard reset either
Does it pick up anything at all? Have you tried tapping all over the place in that region to try and get a response, sometimes just under the screen also works. Do you use a screen protector? If not, try it with one, if yes, try it without, it may be interferring with it, or it may help the touch be picked up by the phone (Stupid, I know, but this is something I found to work before with my elfs, and omnias)
When it is locked, is activesync picking the phone up? You may be able to put the remote.exe into the windows folder (for myMobilier) and do it that way.
A digitizer costs about £6-£10. But due to the age of this device, as sad as it is, I would suggest trying a new phone out if funds allow for it.

ok so far i tried the hard reset (red button and green and pressed the on off button but nothing. When i press on off button alone it switches off but not hard reset. I did not know i had a reset hole at the bottom of the phone.I did that with red and green button but nothing. Only when i poke the hole alone it does a hard reset i think but when i switches back on it is still unresponsive and locked screen
I tried poking under screen protector nothing. Also i think screen is still responsive because when i tap on it, the screen lights brighter
I tired putting remote exe file on the phone( active sync is working and i can read files on the phone) but i have two remote files..which one to use ? the one that ends with 40 one or 50 .Also where to put it specifically..which folder.I tried my windows mobile based device but nothing.Also tried program files and data application nothing.
Mobiler cannot connect since from pc alone because it asks my phone permission
and i cannot tap yes to accept program.
so any more suggestions please

Hi
Maybe I wasn't clear enough, here's the exact procedure, it should work since you have to use only hardware buttons:
Hold down send/reject buttons (green/red at the front) and reset with the stylus; release the stylus but keep holding the buttons till you get 'this will erase all your personal data' message, then press 'action' (big front button) to hard reset.
If Hard reset doesn't work then your device hardware is faulty.

If he hard resets he will liekly not be able to align the screen on initial setup tito12.
Avanisha. If you try to run one of the remote.exe it will say this is not a valid windows application, thats the one that needs to go into windows on your phone.

captainstu72 said:
If he hard resets he will liekly not be able to align the screen on initial setup tito12.
Click to expand...
Click to collapse
Hi captainstu72, i was under the impression that he messed up something in his system so a hard reset would hopefully solve the problem. In case he still can't align the screen after HR then he has to replace the digitiser. Mymobiler will not solve anything, pls read the 1st post: he wanted to do a factory reset. He just have to sync before HR.

thks tito 12..problem was solved with your help.J ust did not get the steps of hard reset right. Phone is working ok now and screen is ok as well as tap function. thank god i don't need a digitizer. thanks to captainstu72 for the help as well .You were right tito..seems i ran a program and then all hell broke on my phone. I wanted to factory reset but as you know the pad was locked.

Glad I could help, enjoy your device

Ahh okay, guess i mis read something! Sorry
Glad its all sorted though, I was just concerned he may end up in an annoying align screen loop