Database Users

Wallaby won't reset - help

My TMobile pocket pc phone edition (sx-56) won't soft, or hard reset. It hangs on the "welcome to TMobile" screen. There is some red lettered text in the lower right hand corner that says:
G324e4
R6.25.02
4.01.16
When I press the on/off switch at the same time as the hard reset switch I get a tri-colored screen that says:
WALLABY
Bootloader
V5.22
GSM OK
And it will hang on that screen too. Any ideas??
Thanks!
Tom Finnegan

tom30215 said:
G324e4
R6.25.02
4.01.16
Click to expand...
Click to collapse
That looks quite normal. No problem with this output....
tom30215 said:
When I press the on/off switch at the same time as the hard reset switch I get a tri-colored screen that says:
Click to expand...
Click to collapse
Are you sure? Normaly you enter the bootloader by pressing soft reset and power button. Have you tired a "normal" hard reset? You have to unscrew your pen and put the small pin into the little hole down under the earphone connector. This had to be done twice.
tom30215 said:
WALLABY
Bootloader
V5.22
GSM OK
And it will hang on that screen too.
Click to expand...
Click to collapse
In bootloader mode this is normal too.....
http://wiki.xda-developers.com/index.php?pagename=WallabyBootloader
Here you can get further information on it.
If the hard reset do not work for you i would suggest to flash the ROM again. How this can be done could be read here:
http://wiki.xda-developers.com/index.php?pagename=Wallaby_HT_FlashSD
HTH
Stefan

new rom made my jasjar a brick :(

I used the new rom from i-mate JASJAR_WWE_13076_164_10900_wwe_ship, it gave me an error message error 116, i followed instructions to recover, no use, i cannot even hard reset any more (it gives me the white screen, and when i press 0, it just goes back to be switched off).
I am going to put back the previous rom if it works...
anyone had this problem? any suggestion how to solve it?
help much appreciated
Nabil

Can u put back on bootloader menu?
In my upgrade it did the same, but it could go to bootlader... then i tryed to flash it again and it worked ok.

bootloader how?
I only get a white screen when i hard resest with x and 0 option...
how do i get to bootloader?
help much appreciated

Reset (stylus) + Power + Light
A thing like that

Bootloader mode: Hold light and power buttons together and reset with stilus.

i get the usb bootloader message
thanx for the tip...
i get the message on the device upgrading the radio stack, so i have access to the bootlaoder, then i get an error message on the pc side...
so i made progress, but still not working to completion

started working at third attempt
hope it works thanx a million dude u really rock!

steps
Since this helped me, I will write the procedure again here:
You need to have access to the bootloader.
Connect the jasjar to pc usb
Access bootloader
To do that u press together the power button and the light button (light button is 3rd button in the front) and reset button (with stylus), u might need to put stylus in mouth to do that as it is a bit fiddly.
The screen will be dark but if u use flash light on it u can see usb written on the screen
Then start the upgrade from PC, u might need to try all of this a few times, it took me three attempts to get the upgrade started
You will also be able to see the message upgrade in progress on the jasjar screen which will be still dark.
Nabil out

Glad that your universal is up.
:lol:

T-Mobile MDA USA weird, "fixies" dont work, stuck in "press send to restore"

T-Mobile MDA USA weird, "fixies" dont work, stuck in "press send to restore"
Hi, sorry for my poor English is not my first language
I have a T-Mobile MDA USA and happened a weird thing, my phone works properly, was CID unloked and sim unloked with TNT_5.0_Wizard_TouchFLO ROM but 3 days ago I put the USB (PC)to charge the battery, lately when I back to pickup my phone I see in the screen of the phone open and close or put an quit windows explorer(mobil) repetitively, i try to close manually tapping in the "X" but explorer continues opening, then I see in the bar where you put the web address the number "3" and "8" was typing continuously, like when you hold pressing the buttons, but nothing was pressing or making pressure to do that, since I cant close the explorer with the "X" I turn off the phone, when I turn on instead to load normally, appears the Align Screen and for some reason will not recognize the Screen Tapping to align the screen, so, I turn off/on again, but in this time shows a black screen with "Press Send to Restore Factory Defaults, Other Key to Quit" in withe letters, it is stuck in there since, before to put this tread I have read this forum and still I am lost, because i do a Soft Reset or Hard Reset #1,#2,#3, I enter into a bootloader mode to re-flash the ROM with CUSTOM__RUU_Wizard_1050412_WWE_101_11210_WWE ... IPL/SPL 1.01 and when finish to flash, its suppose the phone restart and windows loading but instead that I get again the same black screen with "Press Send to Restore Factory Defaults, Other Key to Quit" in withe letters, ok, maybe with other recently ROM, then I enter into a bootloader mode to re-flash the ROM... AGAIN... but now with ruu_prodigy_226102_22610105_022511_tmous_wwe_ship... IPL/SPL 2.26 ... and AGAIN I get the same black screen with "Press Send to Restore"... I try to press send key always, but nothing happens, is still stuck there always, I could not get past that, I would really appreciate any help. Thank you so much.

I hate to ask this, at the risk of sounding too obvious, but are you sure that it was CID unlocked properly? I have a Cingular 8125 with IPL/SPL 2.25 and I know it was a hell of an effort to get it CID unlocked, five or six tries before it worked properly and I was able to flash successfully.

l33tphreak said:
I hate to ask this, at the risk of sounding too obvious, but are you sure that it was CID unlocked properly? I have a Cingular 8125 with IPL/SPL 2.25 and I know it was a hell of an effort to get it CID unlocked, five or six tries before it worked properly and I was able to flash successfully.
Click to expand...
Click to collapse
yes was CID unlocked properly, I do it with lokiwiz02b like 3 moths ago and I use Wizard Service Tool to see was really unlocked, I could flash any ROM since was unlocked I could use crosbow,faria, Molski even TNT.20273_Professional ROM's but I prefer use TNT_5.0_Wizard_TouchFLO because I feel my phone works more stable and speedy... searching in treads I see Im not the only one with the same problem (stuck in a black screen with the legend " Press Send to restore factory default, other keys to quit" in white letters) but in that treads no one get answer how fix this problem or how get out of the black screen.
like I say before I could put my phone in bootloader mode and re.flash the ROM wherever I want to try running ROMUpdateUtility and always I reach 100% then, when its suppose the phone restart and you will see the windows logo or T-mobile, don't happen that, instead I see the famous black screen with white legend, so the legend says me "press send"... I press send, or any key and nothing happens... I read in other treads when you press send the phone formating but this is not the case, just don't do nothing,.... realy I need some help here
thanks

Hey!
I have the same problem as described above. I've been using CR96 Touch HD WM 6.1 with soft SPL unlock for couple of months with no problems until tonight when I noticed that my phone is hanged. I did a soft reset, but the phone gets stucked at "press send to restore factory default, other keys to quit" screen. At that none of the buttons work, soft resetting just puts it back to this screen, the same goes for taking the battery out. There have been no software or registry changes within weeks - just using basic phone functions. Is there any way how to fix this or what could be the problem?
Thanks in advance

no one want reply me :=(

with big mistake i was flashing my ELF with a wrong rom( svp s650)..
it unbootable I tried everytings hard reset soft reset nothing changes: = (just the green light that stays on ..
help plz and thanks
Reply With Quote

muslim2009 said:
with big mistake i was flashing my ELF with a wrong rom( svp s650)..
it unbootable I tried everytings hard reset soft reset nothing changes: = (just the green light that stays on ..
help plz and thanks
Reply With Quote
Click to expand...
Click to collapse
Hi
Sorry to hear your problem, try to read this guide http://forum.xda-developers.com/showthread.php?t=406721 and the stickies in the Elf Upgrading
Hope you can save your device

i have read it but i dont find the sollution :=(
can you help me plz ????

muslim2009 said:
i have read it but i dont find the sollution :=(
can you help me plz ????
Click to expand...
Click to collapse
Hi
Does it go into bootloader (3 colors )?

no no bootloader...
just the green light that stays on
i was tried bootloader and soft resest and hard reset nothing :=(

nothing again
no no bootloader...
just the green light that stays on
i was tried bootloader and soft resest and hard reset nothing :=(..
if you can give a vedio explean how i can result this problem..
and big thanks from morrocco

muslim2009 said:
no no bootloader...
just the green light that stays on
i was tried bootloader and soft resest and hard reset nothing :=(..
if you can give a vedio explean how i can result this problem..
and big thanks from morrocco
Click to expand...
Click to collapse
Hi muslim2009
I tried a few searches but all the results say you need the bootloader screen , are you sure you didn't miss a step in hard reset or bootloader mode :
To enter the bootloader:
Hold down the camera button and reset device with the stylus. Keep holding the camera button until you see 'tricolor' bootloader screen.
An alternative way to enter bootloader:
Switch the device off by long pressing O/I (power) button. hold down the camera button while pressing the O/I button about 1 second. Keep holding the camera button until you see 'tricolor' bootloader screen.
Alternative(universal?) bootloader(3)
As almost all htc smartphones with onboard camera, when you push and hold the camera(photo) button, and plug in usb adapter. Even a "stupid" usb power adapter will work.
To hard reset:
Hold down send/reject buttons (green/red at the front) and reset with the stylus; release the stylus but keep holding the buttons till you get 'this will erase all your personal data' message, then press 'action' (big front button) to hard reset.
I sincerely hope it helps
I was also born in Morrocco at Casablanca and lived there until age 16. Anyway I'll continue searching.
Tito

thanks for help,but it won't work :=(..
[email protected]
add me if i can show you my htc ..
thanks from morocco

I'm not sure if it's possible with the HTC Touch, but I know when I was playing around with an old iMate SP3i (smartphone) I was able to do a ROM upgrade from files on the memory card.. Took me a few attempts to get it right, but it worked. I think I also upgrade my SP5 to WM6 from WM5 that way, but I'm not too sure about that.
Either way, a basic idea of what I'm talking about can be found here, but that is obviously for a different phone.. Maybe some of the more common members here would have better luck finding a similar process on a Touch....?

maybe its will be workin but what marterial i will need for this opperation??

On some HTC devices (cheetah, for example) if you put the ROM file (.bin) in the root directory of the SD card, the phone will flash directly from the SD card.
I think you do require to put the phone into bootloader for that to work though ... not 100% sure, but probably worth looking up.

Ok... Been trying to search for more information for you, but with not really knowing all the correct terminology it's taken me a while longer than I thought. I've found two threads that have some of the information I was looking for:
Recover / Revive your dead / bricked HTC ELF or ELFIN
Recover HTC Touch from tricolors RUU boot-loader (Mtty)
The second link is actually found inside the 2nd post (I think) of the first thread I mentioned here, looks like they are linked in some way. Your best bet is to read through and see if it is something that may help. Let us know if this works for you...?

thanks you man,i was read the first link befor..i will see for the second
hope will work.thank you again

[Q] HTC Touch HD problem !

Hello guys.. well i have a Blackstone HTC Touch HD..
I've got a big problem !
The htc wont start ! Nothing happens when i push the on/off button..
When i put in the charger.. the orange light turns on for some seconds.. then it turns off.. and then the phone turns on.. it shows "Smart Mobility" and vibrates..
Then it restarts.. and shows it again.. and again..
It keeps doing that..
What is the problem ? Can i solve this ?
Thanks !

YouBou1992 said:
Hello guys.. well i have a Blackstone HTC Touch HD..
I've got a big problem !
The htc wont start ! Nothing happens when i push the on/off button..
When i put in the charger.. the orange light turns on for some seconds.. then it turns off.. and then the phone turns on.. it shows "Smart Mobility" and vibrates..
Then it restarts.. and shows it again.. and again..
It keeps doing that..
What is the problem ? Can i solve this ?
Click to expand...
Click to collapse
Is this a new device? Have you recently flashed any new roms/software onto device?
If I where you I'd try a hard reset. To hard reset device:
1. Turn off device
2. Hold down vol up & vol down
3. Continue to hold down vol up & vol down and press power on button at top of HD
4. You will be presented qith a white screen & blue text
5. Follow instruction and restore factory settings (Hard reset) by pressing vol up.
If this doesn't work and device is still playing up and its a new device without any new rom/software on it I'd return it and get a replacement. The alternative would be to flash a new rom on it, but if its faulty device from start I wouldn't recommend this and I'd return it.

Fallen Spartan said:
Is this a new device? Have you recently flashed any new roms/software onto device?
If I where you I'd try a hard reset. To hard reset device:
1. Turn off device
2. Hold down vol up & vol down
3. Continue to hold down vol up & vol down and press power on button at top of HD
4. You will be presented qith a white screen & blue text
5. Follow instruction and restore factory settings (Hard reset) by pressing vol up.
If this doesn't work and device is still playing up and its a new device without any new rom/software on it I'd return it and get a replacement. The alternative would be to flash a new rom on it, but if its faulty device from start I wouldn't recommend this and I'd return it.
Click to expand...
Click to collapse
its new yeah.. after hard reset it still doesnt work
in bootloader it says : BLAC100 32M
SPL-1.14.0000
MicroP-BlackStone (LED) v6
i just fount the mobile somewhere

YouBou1992 said:
its new yeah.. after hard reset it still doesnt work
in bootloader it says : BLAC100 32M
SPL-1.14.0000
MicroP-BlackStone (LED) v6
i just fount the mobile somewhere
Click to expand...
Click to collapse
TC,
You lost me right there. Did you just say you FOUND the mobile somewhere!?
Cheers.

YouBou1992 said:
its new yeah.. after hard reset it still doesnt work
in bootloader it says : BLAC100 32M
SPL-1.14.0000
MicroP-BlackStone (LED) v6
i just fount the mobile somewhere
Click to expand...
Click to collapse
Ah, so you just found the device and decided to keep it...LOL
Well seeing as you can get it into bootloader, you are able to flash new roms onto device. All you need to do is follow guide in my signature.
The only other options would be to return it under insurances/warranty. But seeing as both are unavailable to you as phone isn't yours.............. If I was you I'd return device anyway and maybe the rightful owner may show some gratitude and give you an award!!
Choice is yours!!!
EDIT
You may also find that the orginal owner has put a phone lock on device rendering phone useless anyway unless you know security code. I have similar lock on mine. If this is the case, be kind enough to return it to rightful owner!!