Hello! I have Ipaq hw6910 Vodafone, I flash it and after soft-reset it is dead. I find solution - jtag. Where is jtag pins on this PDA?
Maybe jtags pins are detectable with software, hardware or oscilograph?
Related
Hello, last week i damaged the usb connector on my trinity now data pin is broke (pin in the middle of connector), connection over the usb cabel with pc is not supported now. Fortunately charging the battery is ok
Because I have on my trinity damage varranty void sticker too, can i try it send to service, or its a waste of time? keypad is not ok too, key down, right and start, sometimes not response, but I order new one from cnn.cn if the service will be unsuccessful, I replace it.
But the main question is, because I cant use USB to upgrade rom? (I need flash original WM5 rom, now I use WM6):
Can i flash over the miniSD card complet firmware? OS, extrom, radio rom? and SPL??? because now i have SPL-9.99.CP and I need SPL-1.07 from my original rom, how it flash and no brick the device over SDcard?
Or can you help me, where I can "buy" new void sticker, or if its possible, can I make it?
Sorry for my bad english
Last question: When service will be unsuccessfull, do you know, where can I buy the new ExtUSB connector? I know that its hard solder on mainboard
Can someone help me to locate flash chip on mainboard of tytn in order to replace it. I have two mainboard, none work. on first I have flash chip dead (only can start bootloader but cannot upgrade any hardspl or any rom, or radio... on second mainboard have problem with main quallkom chip, dont have all contact on board itc ripped from board... So I think to put the flash chip from second to first board, but I can't find any scheme over the internet for tytn chip position! I really need for help from someone!!! PEACE!!!
Hi,
I've found jtag pinout for HTC Magician,
HTC Magician JTag Pinout
I've killed my device during update, and as far as i know i must use Jtag to unbrick my device,
I've built Xilinx DLC5 JTAG Parallel Cable III for this,but donno how to do that...
so i donno which adapter or software i need to use for jtaging the device,
where can i download the bootloader file to flash into my device?
i'm asking because i donno how to do this at all !
can anyone help me to do this ?
I need a complete step by step solution for this questions.
Thanx...
It's posible to upgrade Radio of an ipaq 614c using the microSD similar to ROM update?
The problem I have is my usb port on my 614c is broken.
Thanks
Just following up, wondering if someone can help.
I'm stuck with FW 0.77
Thanks
USB header broken?
I don't know if you still need it but i know that it is possible to replace the broken USB n=mini connector in a few cases, as long as the chassislines are not broken too.
I try it, replaced 2 times, but the welding point are so small that they disconnets when charge the baterie again
deleted..nvm
Hi. Hd2 T-mobile Have stitched as usual HD2 Leo. Now it is defined by the computer as "qualcomm diagnostics interface 3197". Whether there is a decision that it to cure or only JTAG?
I have the same problem.
Question - is it possible to restore this device?
i'm assuming you flashed a ..51.. version radio? if so, currently no known fix.
I do not know what happened to him.
The previous owner said that updated the firmware, but what specifically - could not find.
Is it possible to somehow check?
Phone does not go into bootloader mode.
well if it wont turn on at all, then no theres no way to see.
however, the most common "brick" on tmous (t mobile us) phones is flashing a non tmous radio. the symptoms are.... won't power on, no charge light when plugged in to charger, and shows up on the pc as qualcomm.
there is currently no known fix.
you could get it fixed under warranty, but you will probably need to go through htc, t mo probably won't help if you don't have a proof of purchase.however you proceed, don't mention flashing, cos they will charge you a few hundred dollars for a new circuit board.
Flashing through JTAG interface will be able to solve the problem?
If yes, are there circuits and software?
Or only specialized devices and software?
HI. have you solved the problem??? my Tmous is brick. Can you help me???
qualcomm = brick