Hello,
I have a question. I updated my original ROM to the B&B 4.0 ROM and it all looks super. But now when i slide the phone into my carkit ( Carcomm CHFS-97 wired carkit ) it mutes my radio and wont come un-mute until i take out the phone. I had no problem with this with my original ROM ( 1.2.404.1 NLD ).
I tried the phone of a friend of mine that purchased it at the same time as i did and that still works fine ( still has original ROM ).
Is there a way to somehow change settings so that the phone generates a proper mute signal again ?
How is a mute signal for a carkit actually generated by the phone ?
Thanks for your time,
Radio mutes, even without phone
I have the same problem.
The carcomm carkit is connected with the radio in the car thourgh several cables.
One of them is a mute cable.
When you receive a call, your telephone sends out a mute signal through the mute cable to your radio.
The problem with the laters update is caused by HTC.
The newest rom causes a constant mute signal that is being send by the phone.
3 solutions according to the supplier:
1 Let the phone hang in the carkit and press it down when you receive a call.
2 disconnect the mute cable
3 downgrade the firmware
My fourth option:
4 find a way to disable the mute signal
Anybody knows how????
I'm a littlebit further.
When you disable the phone (commanager).
Slide it into the carcomm carkit.
And then enable it again.
Then the mute signal seems to behave accordingly.
Still no idea to disable the mute signal before sliding it into the carkit.
Carcomm carkits
Regarding the mute issue's for the S710, P3300 & P4350.
Carcomm are developing a software patch to solve this problem with these devices.
It seems there is somewhat a problem in the new Roms from HTC..
I´ve sold quite a lot off these kits..and the problem with mute on constantly came with the latest ROMS from HTC...
same applies to the parrot bluetooth kits.
Hey Folks,
I have been reading some posts here about BT and/or BT Mute problems, but my issues seems to be a bit different, plust I didn't have it 1-2 Months ago, so I think it might be ROM/Radio upgrade related ...
Right now I am running udK Diamond R8 which works perfectly fine in general.
I got my phone hooked up via BT to my car BT handsfree (it's a Peugeot 207cc which uses some Parrot BT stuff I think). This used to work perfectly fine when I first started using the polaris in the car. I don't remember when the problem started to appear, but now, when I receive and accept an incoming call, it takes 4-5 seconds, till the polaris switches audio to handsfree, meaning after accepting the call, I can't hear the other party on my car speakers ... but I can hear sound from the regular polaris speaker, very quietly of course.
After those 4-5 seconds, everything is fine and the call is switched to the car handsfree set.
The BT connection to the car set is fine all the time ... no problems connecting or pairing.
Anyone experiencing similiar issues?
boba
Hi,
I have exactly the same problem with my C4 BT handsfree system (Parrot BT components) for some months ago. I have had a look at a lot of forum, but no answer and no solution.
Some days ago, I flash my HTC Polariswith the original WM6.1 Fre, but no improvement. I still have the same problem, 4/5 seconds before hearing the caller.
(PS : sorry for my poor english )
Bemi
Same for me, it worked fine before with the original ROM
ROM : 1.25.406.1 FRE dated 12/12/07
Radio : 1.58.21.23
Protocole : 25.65.30.04H
It happened suddenly.
I tryed a lot of modifications in the register, but no improvement.
I hoped to resolv this problem with the new original WM6.1 but no improvement.
Next week, Citroen will change the radio (it stops working many time a day).
I hope this will resolv the problem.
Bemi
I don't know excatelly the model, but it's the one with Bi-Tuner, BT, MP3 and without Navidrive.
Bemi
Same for me "and without Navidrive"
Probably the RD4
Bemi
Today, I tried several other mobiles (Samsung, Sony-Ericson, Eten, Alcatel) for my problem of delay with incoming calls.
All of them work properly and, as soon as I receive and accept an incoming call, the sound switches directly to the handsfree of the car.
So, what is the problem with my HTC Cruise ?
Any idea ?
Bemi
i'm having the same problem with a Sony DR-BT20NX headset
It has been working earlier.
But now , on incoming calls , the phone ring and later i ear a little signal in the bluetooth headset.
To accept the call , i've to use phone buttons ) .
The sound comes out the phone .I've to speak in the phone.
Otherwise i can listen music with the BT headset and make outgoing calls.
Rom : M-Amine 2.FRE
Radio : 1.59.42.15
( same problems with PDA viet Rom's V33 à V35 )
I don't remember if i've the problem since i've upgraded to radio 1.59.42.15 , sorry
Never had answers on differents forums ..
BT Joined Stereo
install advance config tool v3.3
go to BT setting
verify that your option is Joined stereo and not mono
I'm using udK Diamond R8. I had a lot of problems with my Parrot ck3100 carkit. It was finally resolved by installing the Murata 1.58.21.23 radio. With the for R8 recommended radio I had bad GSM reception, BT connection failure, random BT mute, Parrot displaying the call would continue when I in fact hang up etc.
Hi,
No change with Advanced Config Tools V3.3
Bemi
I have a different BT problem.
i am currently running Touch-IT m2d Beta. but i have always had this problem, even on the original official rom.
i pair my phone with a JVC KD-BT1 CD Head Unit in the car.
i sent this to HTC support (before i started flashing new roms to my cruise):
------------
HTC Touch Cruise. rom: 1.26.710.1 wwe radio: 1.58.21.23 protocol: 25.65.30.04h. bluetooth problem. when i have BT enabled on the htc, i get in the car and it pairs with my audio system. after i make the first call it disconnects (stops pairing) after the call is finished and then after 60 seconds, it pairs up again and i can make a call again. this happens after every call. i had a nokia and i-mate jasjam before with no problems whatsoever. any patch or update available?
------------
AND THIS WAS THEIR REPLY:
-------------
Bluetooth should be universal or is marketed as universal although it is far from the truth. Certain chipsets conflict or are incompatible with others. If a device is not fully compatible it will not offer all features or possibly not connect at all. I have included the below for current tested devices.
-------------
I DON'T think this is going to be fixed any time soon, so i'll live with it!
Hi every body.
I've got the same problem.
A Cruise Rev B, and a BT car's Kit (included in a peugeot, I thing a RD4/parrot stuff)
Actually my first call is ok, and then, heads phones are cutted (sometimes after 3 or 4 seconds), but my microphone still works.
My car's BT is still paired, and sometimes indicates that I'm still phoning, even if I've cutted it on my phone.
I'm happy to find some user's in the same "panade" than me, but I hope we will find a solution...
Who knows how it works and communicate?
It has to be radio problem.
Originally I had WM 6.0 Pro on my Polaris, and BT was working flawlessly.
Then I was stupid enough to upgrade to 6.1 WWE, and now I have all kind of trouble with BT connectivity. Downgrading back to 6.0 DID NOT help!
InSomNiaK said:
A Cruise Rev B, and a BT car's Kit (included in a peugeot, I thing a RD4/parrot stuff)
Actually my first call is ok, and then, heads phones are cutted (sometimes after 3 or 4 seconds), but my microphone still works.
My car's BT is still paired, and sometimes indicates that I'm still phoning, even if I've cutted it on my phone.
Click to expand...
Click to collapse
I have exactly the same problem, based on a slightly different configuration:
My car is a Citroen (with the RD4/parrot factory built in BT)...
My phone is a HTC TyTNII.... with WM6 I couldnt even pair the phone, so I upgraded to WM6.1
Actually I had to drive to the workshop to cut the power on the car, because the parrot BT unit wouldnt stop even tho my phone was off in the meantime.
I start to believe this is not a problem caused by my phone, but a fault SW version on the parrot unit.
I have pioneer deh-p7000bt and it works flawlessly with my polaris in handsfree and a2dp mode.
to have better quality i have to turn srs wow hd off.
in advanced config i set:
-use joint stereo: no
-bitpool: very high
-max bitpool: 64
-min bitpool: 32
-sample rate: 44100
-audio getaway: enabled
Is there anyone who solved this problem yet? I have the exact same problem. When someone calls me, I cannot hear the other party through my car speakers (Citroën C5 newest model without navidrive)
I just tried http://www.jetwaremobile.com/ and this seemed to solve my problems. I had to restart my TC after installing this and removed the relationship in my car. After I made a new relationship (pairing) everything seems to work fine. If this changes I'll let you know.
I am having the same trouble, which started after upgrading to WM 6.1. Am I right in understanding that the Bluetooth is controlled by the Radio ROM and if so is it possible to downgrade just the Radio ROM? I think mine originally came with 1.58.25.14 and the upgrade replaced it with 1.59.42.15, is there a procedure to do this, and has anyone had any success.
Sorry had a search and found http://forum.xda-developers.com/showthread.php?t=381600 which shows how to install just radio ROM, am just unclear as to whether you need to install Hard-SPL first as it is an official ROM and as to if changing radio clears all personal data from the phone.
I use to have a similar problem with the 4-5 second delay. i found that once the car is paired up with the phone, i ran bluetooth audio toggle, or other bluetooth audio program which makes all audio go through the vehicle all the time, including GPS navigation. This way when the phone rings, the ringtone can be heard through the speaker and when you answer it will be instantanious....... in theory.......... i mean, it worked for me anyway....
Then all you have to do is find some way to auto run the toggle everytime you pair your device to the vehicle...
Has anyone got any suggestions regarding the following problem:
HTC Tattoo (UK Orange but flashed with stock ROM)
Nolia CK-1W Bluetooth in-car handsfree kit with Telemute harness(sound through car stereo)
Phone paired with system and connects perfectly every time I get in the car.
Outgoing calls work perfectly.
Incoming calls - mutes music on stereo, rings over stereo, pickup via phone or handsfree remote button NO SOUND from caller(though I can hear them on the phone speaker).
Seems to me that it's either a bug in the Bluetooth implementation on the phone or a setting I havent found. (It works fine with my Nokia E51)
Any ideas?
Thanks
Hi...!
I have the same Problems with my Nissan Car Headset from Factory with Android 2.1 and 2.2...! Similar Problems are with the HTC Wildfire and HTC Desire
I can connect the phone with the System, Phonebook reading, take calls and arrive calls but i cant hear anything (on both sides)
With my original Tattoo Rom 1.6 its working perfect and Audio Streaming too...
according to the German HTC Support the problem is well known and they are working to fix the problem... but i cant find other Android users with the same Problems except you
Why????
Thanks
I have updated by HD2 to Android 2.3 but the buttons of my HD2 headset is not working. I press them when recieving calls and playing mp3 but there's no reaction. Is there any way to solve the problem? Thanks
same problem here although i'm not quite sure if the problem is from Android, use a multimeter to see if there is a broken wire
Some of the kernels in some of the roms don't support the headset buttons working properly. which kernel does the build you are using contain?
The same problem is with my build and furthermore, the headset works only with any player and FM radio - I can't talk during phone calls because my receiver doesn't even hear me and I have to unplug the headset from the phone jack in order to talk during phone calls.
Tested on Typhoon CyanogenMod 7 2.1 (not tested on the current version).
Sorry to bother you but I'm looking for a way to disable the headset when not used.
Unfortunately my Tattoo seems to have a broken switch, so it doesn't detect when I pull out the jack and it keeps sending all the audio signals to the headphones (which are not there), so the speaker is muted all the time (even when I'm making a phone call - I have to use the loudspeaker).
On 1.6 I used to have this http://code.google.com/p/toggleheadset/ and it worked _really_ nice, but on 2.0+ it doesn't seem to work.
Since it's opensource, is there any java coder willing to port it to 2.0+ and make a poor Tattoo-guy without warranty happy?
Anyone with my same problem?
Anyone willing to solve it?
hi all ,
got a pb with it to , but not the same .......
on sense rom : when i plug juste a headset ( with no mic ) its ok , i can use the phone mic to speak ... ( the small icon is ok ) but ....
on non sense rom : ( with the same headset ) , i see a headset with mic icon ... so i heard on the headset but the phone mic is not active