Device lock - 8525, TyTN, MDA Vario II, JasJam General

Since getting my Hermes (SPV M3100) I've had the same code for unlocking my phone. However, the other day my messaging program crashed, which it does sometimes, so I rebooted the phone and when I put my code in it said it was wrong.
I'd just reflash it, but to sync it needs to be unlocked. Ideally I want to keep all my messages and contacts, but if anyone knows how to reflash it then that'd be awesome too.
I'm currently using a pink phone which doesn't even have a vibrate function. It's a bit of a nightmare.
Can anyone help me? x

Does no one have any idea?
Is it an expensive paperweight?

You've probably lost all data that you didn't have backed up, but hopefull the phone isn't a write-off. Do a hard reset by holding both soft-keys while pressing reset, and if that doesnt work you can put it into boot-loader by holding 'ok' and 'power', and pressing reset.
Make sure you read up on hard-spl and flashing from sd first.

Related

Locked up, please help

Hi,
I have a tmobile MDA (wizard). I attempted to install some software on it, but disconnected and rebooted before it was complete (it appeared to be just spinning).
Now after a soft reset, screen shows only 'Windows Mobile' after booting, and none of the buttons work and I can't advance from this screen.
Is there a way to hard reset that doesn't involve using the OS (ie, I can't click on anything because it's not getting to that point).
Also in this state activesync isn't detecting device.
Thanks in advance! - Chris
Hold down (and keep holding) the camera button while depressing the reset button. Hopefully it boots into a tri-color screen. If so, plug it into the USB port and, at the bottom of the screen, it should display "USB". If that happens, flash it with a *known good rom*, such as a stock T-Mobile rom. Don't try to be clever, the object is to get the phone working. Once the flash has started, *get up and walk away* for 15 or 20 minutes. Don't check in on it, leave it alone, It takes some time. When you hear it's little chime, it's done, rebooted and ready. If any of the above doesn't happen or the flash outright fails, then you may have trashed it permanently. It doesn't sound like it's beyond hope yet, however.
i have the wizard and im having the same problem after installing a ROM from this website...it just goes to the windows mobile screen with the numbers then shuts off...id really like to save my phone is there anything else i can try because that hard reset thing isnt working
axxeman001 said:
Hi,
I have a tmobile MDA (wizard). I attempted to install some software on it, but disconnected and rebooted before it was complete (it appeared to be just spinning).
Now after a soft reset, screen shows only 'Windows Mobile' after booting, and none of the buttons work and I can't advance from this screen.
Is there a way to hard reset that doesn't involve using the OS (ie, I can't click on anything because it's not getting to that point).
Also in this state activesync isn't detecting device.
Thanks in advance! - Chris
Click to expand...
Click to collapse
Well same thing happened to me a few days back.. I had to Cold Reset [which restored it to factory defaults], but hey I got it working again..
Press Communication Button [Top Left] and Record Button [Top Right] at the same time and use the stylus to soft reset..
You will get a black screen, asking you to press "Send" to reset to "Factory defaults"
Press "Send".
Hopefully you should get your MDA working again ...
I read the "Above" in the HTC Wizard Service Manual [PDF] on the *last page* under the "Cold-reset" Section..

Bootloader Mode

For some reason my Wizard G3 will not go into bootloader mode, any ideas would be much appreciated...
For clarification, it is stuck at the Hard reset screen asking me to press send. When pressed nothing happens. I have tried key combinations and the battery tricks. Any help out of this would be great. Thanks.
--Resolved--
After a bit of toying, playing with the battery, and a few more shots at it this morning, the phone successfully reset into boot-loader mode. Next step is killing me though.
Despite using the stock RUU wizard and trying another few ROMs, I can not get the phone to get out of the "Press Send to restore factory defaults" screen. Any ideas would still be appreciated.
It seems to be hardware problem your SEND button
DONT WORKS!!!!!
Open up and see what is bad... so
maybe you need to get it works i think your MDA is a Second hand very cheap becasue of that.!
yes i also have this problem with my k-jam it was on bootloader mode now after the hardreset its stuck on press send botton to default other to quit but infact its not do yes or other??

Unable to unlock device

Hello,
Wondering if someone can help me, i have a very strange problem indeed!
I've just rest my device and when it came up with the Unlock screen to type in my unlock code (4 digits) I can press the buttons on the screen, and the code is typed in, but when I come to press any of the unlock buttons, they do the physical depress animation but it's as though they are not registering the click event.
This is on Mirri WM6.5 rom.
Any help would be appreciated, I also tried to use MyMobiler to use my mouse to try and do it, but as I last used it as Mass Storage, it won't connect as I can't get to set it as ActiveSync.
*Edit - Further update, if I dial 999, I can correctly press the cancel button, which means it's not that portion of the screen which is obscured, it's just the unlock, contacts, mail buttons that are failing to unlock the device. I receive no error messages when typing incorrect codes either.
Could it be possible a program has changed my password?
Thanks in advance folks.
D.
** HARD RESET DEVICE **
Too business critical to keep messing about, please leave comments if you have any ideas incase this happens in future.
I severely doubt your password has been changed. If you are unable to press unlock, it may be worthwhile performing a hard reset to see if this fixes your problem. Obviously backup contacts, emails etc beforehand as you should still be able to do this.
Hi,
I was unable to do anything with the device, so had to hard reset.
As the device was locked upon startup, the only thing i got was the enter device unlock code screen.
I know the changed password is a strange idea, but can't think of anything else unless my device is actually knackered... just finished hard reset now.
THEAnarch1st said:
Hi,
I was unable to do anything with the device, so had to hard reset.
As the device was locked upon startup, the only thing i got was the enter device unlock code screen.
I know the changed password is a strange idea, but can't think of anything else unless my device is actually knackered... just finished hard reset now.
Click to expand...
Click to collapse
Any joy after hard reset?
All seems to be working perfectly now, have lost a few days of txts since my last backup, but otherwise all up and running... very strange indeed!!
Thanks for checking back

Phone is locked or Bricked? Can you help?

I am using the PCarvalho eXtreme ROM on my phone. Everything was working fine until I entered the wrong PIN and PUK too many times. My SIM card was turned inactive. I went into the store and got a new SIM card and had the contacts transferred to the new card.
Once I put the new card into the phone, I tried the PIN and hit Unlock. The phone does NOTHING. It just sits there like I did not hit the unlock button. Then I hit the button again and again and see that the screen has registered the touch and the button press, but nothing happens. I do not get a message that the PIN is invalid and the Phone does not unlock.
So what can I do? If I attach the phone to the PC it tells me to unlock, which I cannot do for some reason. Is there a way to restore the phone to default ROM or to reload a ROM once if the phone is locked and will not accept an unlock code?
try another phone? i doubt it is rom related.
unfortunately I do not have another phone that could be used. Is there anyway to restore the old phone to make it work? The blackberry I have from work is sim locked to a different provider
Did you hard reset the phone? Try that if you have data backed up. You can also try flashing the original WM 6.1 and see if that works and then go back to pcarvalho's ROM again.
If by hard reset you mean taking out battery or pressing the button on the bottom, I have done both of those. If that is not hard reset, what do you need to do to execute a hard reset?
confusedxx said:
If by hard reset you mean taking out battery or pressing the button on the bottom, I have done both of those.
Click to expand...
Click to collapse
What you have done is called Soft Reset or commonly SR.
What you need to do (WARNING: you will loose all your contacts/pics/music/etc. in the phone memory) is take out your MicroSD card (just in case ) and while pushing GPS and Internet Explorer Buttons SIMULTANEOUSLY with one hand take the stylus and push reset with the other. Then continue holding the two buttons mentioned above until you see a gray screen that says: Push Send to Hard Reset the Phone. Push Send button then (you now can release those GPS and IE buttons ) and you've got a clean system.
Oh that sucks if I lose the contacts. hmmm well worth a shot to see if any are backed up on sim
confusedxx said:
Oh that sucks if I lose the contacts. hmmm well worth a shot to see if any are backed up on sim
Click to expand...
Click to collapse
If the phone is somehow still recognized by a PC, you can try syncing your data beforehand.
I would love to DesertsStorm but the phone will not allow for sync if it is locked. We shall see.

Stupid Problem with P3452

Hi all
first post and i got an interesting problem with my phone which i qualify as stupid. It all started when when my virtually keyborad started becoming unresponsive and when i tried to do a factory reset, i could not enter the 1234 number to start it. i left the phone for a while and then i could not get into the setting even . But i could receive calls but i could not call since i could not access any numbers on the dial pad( by pressing on the numbers of coruse but from dial log screen i could)
Anyway long story short while fiddling with the phone , i thought the lock feature was on that is why some of the touch functions was not totally responsive but to my sadness, i activated the lock and now the phone is stuck on the front page and i cannot access anything since i must press unlock at the far corner of the down screen but stupidly, while pressing on the unlock, since it is unresponsive, i cannot unlock the phone to get to the normal menu and so on.The only thing working is the square pad which tells me to press cancel then unlock to free the phone for normal use
By the way the lock feature is the one that blocks the phone so that you do not accidentally press on the touch screen and activate a program and not the lock thing operators put to limit your phone
I want to know if anyone can help me unlock the screen so that i can reset the phone or alternatively any other method via usb to reset my phone to factory settings. Any special buttons on the phone i can do to do that?
I tired leaving battery out for 24 hours but that did not work to unfreeze the touch buttons
Was thinking to reload the windows mobile completely via the micro card (which i read here) but i am not sure it will work or i fear it might brick my phone
Any suggestions will be welcome please.... thanks
Use myMobiler to control device from Pc through usb
Good luck
Ps: you'll probably have to change digitiser afterwards
Well tried the mobiler but the thing is that it asks the phone to allow the program to conenct and i cannot press yes on the touch screen since it is frozen or something so i am stuck again.
Very strange, it doesn't ask anything on my device...
Why don't you hard reset: press green and red buttons and while pressing, poke the stylus shortly in the reset hole then release the 2 buttons. It will ask something that you probably won't see, just press the action button and wait for it to restart.
Don't flash another on just yet - it may well cause issues as it sounds like your digitizer is broken. Don't hard reset either
Does it pick up anything at all? Have you tried tapping all over the place in that region to try and get a response, sometimes just under the screen also works. Do you use a screen protector? If not, try it with one, if yes, try it without, it may be interferring with it, or it may help the touch be picked up by the phone (Stupid, I know, but this is something I found to work before with my elfs, and omnias)
When it is locked, is activesync picking the phone up? You may be able to put the remote.exe into the windows folder (for myMobilier) and do it that way.
A digitizer costs about £6-£10. But due to the age of this device, as sad as it is, I would suggest trying a new phone out if funds allow for it.
ok so far i tried the hard reset (red button and green and pressed the on off button but nothing. When i press on off button alone it switches off but not hard reset. I did not know i had a reset hole at the bottom of the phone.I did that with red and green button but nothing. Only when i poke the hole alone it does a hard reset i think but when i switches back on it is still unresponsive and locked screen
I tried poking under screen protector nothing. Also i think screen is still responsive because when i tap on it, the screen lights brighter
I tired putting remote exe file on the phone( active sync is working and i can read files on the phone) but i have two remote files..which one to use ? the one that ends with 40 one or 50 .Also where to put it specifically..which folder.I tried my windows mobile based device but nothing.Also tried program files and data application nothing.
Mobiler cannot connect since from pc alone because it asks my phone permission
and i cannot tap yes to accept program.
so any more suggestions please
Hi
Maybe I wasn't clear enough, here's the exact procedure, it should work since you have to use only hardware buttons:
Hold down send/reject buttons (green/red at the front) and reset with the stylus; release the stylus but keep holding the buttons till you get 'this will erase all your personal data' message, then press 'action' (big front button) to hard reset.
If Hard reset doesn't work then your device hardware is faulty.
If he hard resets he will liekly not be able to align the screen on initial setup tito12.
Avanisha. If you try to run one of the remote.exe it will say this is not a valid windows application, thats the one that needs to go into windows on your phone.
captainstu72 said:
If he hard resets he will liekly not be able to align the screen on initial setup tito12.
Click to expand...
Click to collapse
Hi captainstu72, i was under the impression that he messed up something in his system so a hard reset would hopefully solve the problem. In case he still can't align the screen after HR then he has to replace the digitiser. Mymobiler will not solve anything, pls read the 1st post: he wanted to do a factory reset. He just have to sync before HR.
thks tito 12..problem was solved with your help.J ust did not get the steps of hard reset right. Phone is working ok now and screen is ok as well as tap function. thank god i don't need a digitizer. thanks to captainstu72 for the help as well .You were right tito..seems i ran a program and then all hell broke on my phone. I wanted to factory reset but as you know the pad was locked.
Glad I could help, enjoy your device
Ahh okay, guess i mis read something! Sorry
Glad its all sorted though, I was just concerned he may end up in an annoying align screen loop

Categories

Resources