Hi, accidentally i flashed my charmer with a prophet rom
Everything is working fine except the USB connection!
ActiveSync and battery power load over PSU does not work.
It is possible to install the correct USB driver over SD card ?
Regards Janos
PS: Sorry for my poor english
Related
hi guys
i am new to this so apprecaite your help.have been using my xda exec for about a firthinte brilliantly.however since yesterday ,when i plug the usb cable to pda nothing is happening,fone is not being recognized by pc.i tried different cables and diferent pc's to no avail.the pda does not even charge via usb cable.
however it charges normally via wall charger.
do you think I bust the connector,could it be fixed?
hi heres what you can do to see it your usb still works
1. have a storage card sd/mmc if you dont have one borrow one
2. download softtick 2 from http://www.megaupload.com/?d=YPH5DW4I or wm5storage you choose
3. connect your pda with softick installed
4.press the usb option and the sd card should display as a normal flash drive
5.if the computer recognizes it and picks it up as a flash drive then you definatly know it works properly
6. if it doesn't then you can hard reset your pda
7:if that still dont work then consult a techniian or a guru to help you open it
hope this helps!
Hello,
i have an mda compact III with an broken usb port. i use active sync via bluetooth without problems.
is it possible to change the rom of my device without a working usb port?
perhaps directly from memory card?
many thanks in advance,
joa
yeah
you need to format your card(not sdhc) to fat32, and copy there a rom file( rename it to arteimg.nbh). After that enter bootloader mode, and slide a volume button.
sd card flashing will work but make sure your device is CID unlocked (in case you are flashing cooked ROM)
Hello,
i have many Problems to connect my Spectec Wlan sd card with my himayala.
I have windows upgrade at windows mobile 6.0.Thats ok.
I get Many Drivers from the INet to run my Spectec Wlan sdcard - No function.
I which order i must install the Drivers. How to install the Networkcard in Windows?
I read many over this Problem. Nothing can help me.
Can me help everyone?
Thanks (sorry to my english)
Speedyggg
no ideas ?
Hi, ALL!
it is possible to connect in HP iPAQ 914 any Flash Usb Drdive.
It is or is it ?
did you did it ?
what driver ?
what cable ?
Drivers are built in; you just need a mini-USB to female full-sized USB cable
i ask this question, when i connected mini USB to external HDD 2.5" and connect external USB power from my laptop.
My 914 dont recognise my external mass storage device in memory applet. and dont show any warning message or so.
roman_n1 said:
i ask this question, when i connected mini USB to external HDD 2.5" and connect external USB power from my laptop.
My 914 dont recognise my external mass storage device in memory applet. and dont show any warning message or so.
Click to expand...
Click to collapse
perhaps you need a usb host cable
i find 'mini-USB-male to full-sized-female-USB-cable'
but my 914 in memory manager don't show an additional storage (it was standart transcend 512mb flah usb drive)
it is possible to turn in registry or in somewere settings - usb mass storage in this device? that connect standart flash usb drives.
windows mobile may read and write to fat32 or ntfs file systems or both?
Sorry for OT, but I have some problem with this iPAQ. I'm trying to flash this device with the latest ROM using PC with Vista on board. After going to bootloader, installer shows message, that connection between ipaq and PC was lost. Can anyone help me? Perhaps I need some drivers to flash this PDA? When I turn BL mode, and connect to PC, Vista see it as unrecognized usb device...
USB Host
this cable MiniUSB (male) - to USB(female)
price is very low 1.5$
byt my iPAQ 914 not recognise flash usb drive in Settings-System-Memory applet.
hardware is ok. i need additional software - driver for WM6.1.
i try to install USB Host Drivers _http://forum.xda-developers.com/showthread.php?t=480899
no effect - my ipaq recognise nothing: my flash usb drive or my external hdd with additional power or any unknown device.
кому надо - есть подробно про все драйвера по-руски тут
The last wm6.5 Rom contains USB Host driver or NOT? and mini-USB can offer 5V power?
Hi,
I have a Vario II that i have flashed many's a ROM on to. However i can no longer do so.
I can get as far as the confirmation screen, click Next, the progress bar appears but remains at zero then a few seconds later activesync crashes.
Flashing the ROM then fails (obviously)
Any idea's?
I have tried searching but found nothing helpful.
p.s. i am flashing via USB
I have expirienced this on the PC at my work. Our PC there has a restriction for USB Drives. The ActiveSync detects my device but when starts to flash the connection is cut. Having an error on the RRU that my USB is disconnected or remove.
Maybe you can check your PC if it can detect your device even without ActiveSync. You can go to your control panel and check if there is no undetected hardwares.
BTW, what is the OS of your PC.?
i'm using XP.
I will try to flash my Kaiser... see if that works.
i can flash my Kaiser so no issues with detection etc.
Still the same issue with my Hermes tho.
Any help appreciated.
Use the SD card flashing method. No need activesync/cable. Read wiki : http://wiki.xda-developers.com/index.php?pagename=Hermes_SDCardFlashing
i had considered that but don't have a card reader. They cost pennies these days so i guess, no excuses!
Cheers.
ZootHornRollo said:
i had considered that but don't have a card reader. They cost pennies these days so i guess, no excuses!
Cheers.
Click to expand...
Click to collapse
If you still have a working WM, you can install WM5storage and make your phone act as a card reader/usb thumbdrive. You can then format and copy files normally like using a usb card reader/thumbdrive
Thats odd. Do you use the same connector on your kaiser?
Also may i ask what's your HardSPL Version..?