G3 problem - JAMin, XDA Neo, S200 General

IPL 1.00
SPL 1.00.0000
OS 2.20.7.34
I frustrated and sadden that I can't fix this problem so I turn to you guys for advice. Please help me.
I was using Prophet Touch X flawlessly, until I saw the Iphone V1 and 1d-super prophet.
I successfully flashed to 1d and it ran great! but I want to see how Iphone looks like so i tried it. That's where the problem arise.
The flashed failed so I started bootloader and flashed back to fantastic b4. It worked but become extremely slow. So i flashed to Nanoscopic and the problem still there.
I also did a Hard reset and it didn't help.
I flashed to 1d-super prophet and nothing changed.
The machine is now extremly slow. The orange amber light won't turn off dispite me flashing different ROMs
Currently as I'm typing, the machine won't get pass the initial IPL, SPL, OS screen. It''ll hang for about 1 minute then fade to white and restarts the whole thing again. It keep on looping.

oh my! I just noticed after my post that my machine intially SPL ending was 0001 and now it's 0000. What the heck! is this the cause of the problem??? is this possible?

update:
I entered the machine into Bootloader and loaded Fantastic b4. All success but when I check the Main battery, it stated that it's being charged eventhough it's not plugged into a power source....very strange.
please help.

More discoveries.
The audio is also not working and machine won't connect to active sync

It's fix!!! So much trouble and time consumped but I'm greatful that it work out well.
I used the Prophet Tools Light and did a Hard SPL flash.
Thanks to the author and this forum. Greatly appreciated!!

Related

my i-mate jasjar is dead

hi all,
my jasjar had an error while upgrading to ranju 7.7,
i tried to reset, didn't came back,
hard reset neither,
i went to bootloader mode, i could,
i connected it again to the pc, it showed usb,
i tried to flash to Rom that was working previously it arrives to 7% than stops,
what should i do ...
i tried to flash with official rom, it says that the rom wasn't designed for this model, it has worked before...
please help...
Hi,
if you search in the ranju's thread there's the solution.
You could have the doc corrupted. Simply read the wiki,
you must use mtty to format your device and then reflash the rom you want (with radio rom also).
Had similar problem
upgrading Imate JasJar to Ranju 7.7, only at first it showed as success, then it started behaving funny during customization, then failed to customize, then got stuck on Windows 6.1 green flash screen and eventually refused to budge beyond blue Imate screen with versions info. I tried everything, a few dozens of hard resets returned me to the same problem, removing the battery didn't do much and mtty didn't show USB as available option, so couldn't even use that. I was pretty much stuck solidly and for a while. At my wits end I read that problems like mine are associated with DOC corruption and my JasJar is as good as dead, quite a few people suggested to those who are in the same position to throw their bricked babies away, as there is no economic solution apart from sending it for service where the corrupted chip may be replaced. What do you know, I followed wiki recommendation and entered a boot screen by pressing light power reset, then just flashed back to Ranju 7.6 and my JasJar was brought back to life!!! The update went without a glitch and everything is working fine. I guess I will keep the 7.7 on my O2 and 7.6 on my Imate for now, won't be risking an update anymore on the JasJar, don't think I have much hair left after all the pulling I did trying to bring it back to life. Hope this helps someone in the same predicament
jokove said:
hi all,
my jasjar had an error while upgrading to ranju 7.7,
i tried to reset, didn't came back,
hard reset neither,
i went to bootloader mode, i could,
i connected it again to the pc, it showed usb,
i tried to flash to Rom that was working previously it arrives to 7% than stops,
what should i do ...
i tried to flash with official rom, it says that the rom wasn't designed for this model, it has worked before...
please help...
Click to expand...
Click to collapse
does it turn on at all?
Does the device turn on at all after a hard reset?
Dude, I had a same problem it rectified though, check following of my blog...
http://jay-joshi.spaces.live.com/blog/cns!851D717EDFF14CEC!3258.entry
or
http://buzzdev.net/read.php?40,13307,page=1
Rarest_Kind said:
Dude, I had a same problem it rectified though, check following of my blog...
http://jay-joshi.spaces.live.com/blog/cns!851D717EDFF14CEC!3258.entry
or
http://buzzdev.net/read.php?40,13307,page=1
Click to expand...
Click to collapse
Problem resolved?

HELP, stuck at bootloader screen

I urgently need help with my BA
I attempted to upgrade to Beta version:WM6.1 CEOS 20262.Build 19949 Aku1.2
by sun dream and now its stuck in the bootloader screen, I have gone through the wiki of BA and have done various suggestions on how to hard reset my device but nothing seems to be working. Any help extended will greatly be appreciated. Thanks and More Power to all you guys!
Flash again. If no progress - flash different ROM. Never forget about proper HR after each flash.
hey out there,
i do have some problems with my Blue Angel the last days, i flashed a new rom
1.15.00
1337.45
V.6.01.09 DVH
and had Problems with active sync, seemed like it didn't get an Ip adress.
so i flashed sunwell 6.1 and i was able to synch but radio rom was missing and i wasn't able to do calls at all. Hard/soft resetted reflashed flashed other roms, but now i stuck directly after the Bootloader screen when showing windows mobile 6 logo.
It makes an annoying "Bling" and it's reacting on commands, Stylus or Power button, but i didn't finish starting even after 10 min. I flashed some other roms.
same problem. any suggestions?
sorry for abusing this thread but i didn't wanted to start a new "wuhuhuhuhu i bricked my friends BA" thread.
thanks florian
edit.
if starting now it shows Radio and GSM None
hm...formatted with mtty restarted
put sim inside.
displaying R,G NONE when booting.
soft resetted, displayed right data.
Booted, finally working whyever.

Here's a tricky problem, need expertise!! Kind of urgent..

I have read and read and read. I have "bricked" my phone in the past and fixed it. I have used, tested, and flashed many roms from this site (Thanks to all cooks for their work!) but I still consider myself somewhat 'new' to troubleshooting.
I woke up this morning to make some important phone calls today and as luck would have it, my phone was stalled again. It's been doing that for a few weeks now. My last flash was Open Touch 5.0 UL I believe (either that or 5.2 biggy) and it has been working great except for the occasional freeze.
EDIT: Forgot to add, the actual problem is now it won't boot up after it froze this morning. Just sits at the boot screen
So I've tried my other methods of fixing it... /edit
Except this morning nothing is working. I have tried flashing with Orig. T-mobile ruu, tried SD flashing with the RUU_signed.nbh, tried restarting the computer, phone, removing battery and sim... NOTHING! When trying the sd flash (which I've never done before today, it reads and tells me to push the down button but then goes to bootloader screen and just sits there. With the RUU I'm getting err 300 but I'm using the SAME RUU (4.10...) that I've used in the past to reflash my phone AND tried the new one (4.26...)
Possible problem: Does it matter what kind of usb cable you use? I don't have the normal one I use as I am not home but I figured usb is usb...
I've read about it being a motherboard issue, how common is this?
I've read somethings about MTTY, would this apply to me??
Please help, anyone who has any suggestion, I'll try it!!
Stats:
IPL 4.10.0002
SPL 4.10.0000
NOT hard-spl'd
Wing w/ Open Touch Project 5.0 or 5.2
actualy the sd method needs hard spl thats all i can really provide
I appretiate it, that I did not know... I could barely find anything on how to do it even.
im having the same problem bt instead of freezing da screen jus goes different colors or jus goes gray and stays der
Thats basically what mine did. The colors would get messed up and no matter what button i pressed it would not do anything. My advice to you edrift, is BACK UP YOUR STUFF NOW and reflash it asap if you can still reboot. I can get into my phone at all now.
yea i tink i might jus throw my phone away.dis is jus gettin rediculous

Need help with a i-mate Jasjar that doesn't start at all..

Hello mates,
My i-mate Jasjar doesn't start any longer. Here's how I got here. I tried to flash my jasjar with Crossbow ROM using ROMUpgradeUt.exe but it didn't do anything. So I went into the Country_ID_Error folder on the computer and executed MaUpgradeUt_noID.exe. My jasjar froze after this and everytime I restarted it just hung on the bootscreen that says i-mate.
So I tried using mamaich method using mtty and now I can't even get to the i-mate bootscreen. So nothing just happens when I try to power up the phone (I'm sure the battery isn't dead).
All I can do is just enter the bootloader mode. That is the only thing that I can do that I know.
Please suggest something. I'm lifeless without the i-mate.
Thanks and regards,
Aditya More.
i had this same issue, i task28?'d my device, whatever command that resets the flash structure, then booted into bootloader, and flashed this file:
http://rs507.rapidshare.com/files/184081773/JASJAR_WWE_11353_137_10301.zip
that should fix you up real good, hopefully.
Well thanks a lot. But it doesn't help. It gives me a connection error when everything is fine. USB is connected, ActiveSync USB connection is disallowed.
I forgot to mention, that when I task 28'd my device, nothing showed on the device. It just showed USB at the top and v2.01 at the bottom for ever, which means the task 28 wasn't probably successful or I ain't sure what.
Yeah, I had to ask you how if the above given file will work if the phone is in bootloader mode.
To fill you on more details, my phone somehow strangely starts. I'll explain how.
When the phone is switched off, and when I press the reset button, nothing actually happens, no activities can be observed.
When the phone is switched off and I connect it to the computer via USB, it shows the charging light. Now when I press the reset button with the phone connected to the USB, the charging light goes off and the USB detection sound sounds on the computer and the computer shows "USB Device not recognized". This means the phone started.
But strangely in both the above cases, none of the two lights on the phone indicate anything and display of the phone shows absolutely nothing.
The only thing I can do with the phone now is enter bootloader.
Also, since I compromised so much, is it possible that I can still flash it with WM6? Because going back to WM5 will make me feel miserable.
Thanks.
@cheapusenet:
I tried flashing with that file. It flashed successfully, but the screen is all smudged. I soft reseted the phone too (using reset+two soft keys) but it keeps displaying that same smudged screen.
Good news is it did something.
Bad new is that it didn't make the mate work.
Please help. I'm dying without the phone.
Thanks and best regards,
Aditya More.
is it possible you can get a picture of what screen its showing? I THINK it happened on mine as well, did you let it sit for 10 or so minutes? if i recall the bootscreen was all corrupted but it started into WM5 just fine.
and regarding wm6, i'd attempt to get the device working before you try and get fancy. is the device cid unlocked? mine was and thats what was causing the issues.
Originally Posted by mamaich
if you can enter bootloader - use "task 28 55aa", this would restore DOC to its original layout.
If you cannot - contact service center.
if you didnt run that exact command, it's probably a good idea.
and you could try reflashing that stock imate rom?
This is all that happens.. I have waited for 5 minutes. I'll wait for 20 minutes now.
i waited for 30 minutes.. no go..
yap it did that EXACT same thing to mine.
reflash it, i think that fixed mine.
if that doesnt work, attempt flashing some custom roms.
is it CID unlocked?
i flashed it twice.. no go..
what's CID unlocked?
CID
Read the Wiki on my sig link
cid unlock allows flashing of roms that don't match your device branding.
i don't remember what brought me back from that, i may have flashed a custom rom with the imate cid settings in it? i don't remember.
i'll post a rom that i think may have helped in a few hours, I have slow upload speed. until then, just keep tinkering.
also, you should only be flashing nk.nbf. not the ms, or radio nbfs.
http://milfweed.info/UNI_AKU3_2_WWE_IVAN_beta_4_extrom_public.rar
try that rom.
hey man.. Flashed the rom with Ranju's ROM of WM6.1.. it worked.. But I can get the phone to be turned on. i mean device turns on but I can't make or receive calls or text. Let me check the thread of that rom. Thanks a ton for your support. Really appreciate it.

Strange case bricked 8525. Need help

I have a cingular 8525 (Herm100) that I was running windows 6.5 on from Scotty 93.
This ROM the HTC Home version.
Recently it started hard resetting randomly and finally the last time it hard reset on its own, it became stuck in bootloader mode. Whenever I try to flash a Rom on it everything works fine and the progress bar comes up until the very end. As soon as the progress bar disappears, the Rom should boot but the bootloader just comes back up. I have HardSPL 2.10 from Olipro on it.
I looked at common bricked hermes cases and it didnt fit any of them. I have run out of ideas of what to do. Any help would be greatly appreciated.
Nevermind
wow. nevermind. I think I may have fixed it It seems like it has an internal battery or something because I had to remove the battery and let it sit for an extended period of time before it would start to boot up normally. Then when it did, I just flashed the old prerequisite ROM as soon as I could establish a connection with my computer. It seems to be working totally fine now.

Categories

Resources