Related
Hi got the xda1 rom/radio upgrade from o2 web site.
installed radio upgrade first, it then asked me to remove ac power, i took it off dockign station, it rebooted, asked me for a simlock.. to which there was no mention of in the upgrade instructions.. i turned it off and on, and now it wont even boot up.. comes on with 02 logo.. then a white screen with blue banner at top..
what can i do to fix it??
i cant even see it on the pc!!!
please advise, i really hope i have not broken it.
can o2 do anything?
i can get to the bootloader by holding down power when soft resetting phone.. comes up with gsm error...
then nothing....
i can get to other menu about sd backup ect if i hold down the two buttons at top of unit when in bootloader.
how do i go about repairing the radio and rom ??
is it possible?
bootloader
ok, i can copy the rom ect from xda to sd card... and even copy it back over again.. so if i put the sd card in a reader on the pc.. and put a good rom and radio on it.. will it work ok booting off the sd card?
i can get to that menu from the bootloader..
You need to get a working rom installed then try to address the gsm error, I never heard of an xda asking for sid code when doing an official upgrade. Did you leave your sim card in the xda when it was updating the radio stack? You may be aware from reading on the forum that radio stacks once corrupted are very difficult if not impossible to rectify. I would suggest unpacking the rom you downloaded, burn just the ce part to rom using sd/bootloader method, then try to install gsm again, this time without sim inserted, you will find here on the forum the instructions to burn gsm from sd card, do this after you have a working bootable system. Good luck.
yes., the sim card was in the system at the time.. its an 02 sim card however, so i guessed this was ok.
printed out the 10 page instructions on how to upgrade s.ware so there was no problems (like this)
the radio stack was installed before the rom if that makes any difference?
is it possible for the xda1 just to lock up like this without having done it the way i did?
perhaps it would have done this anyway??
just thinking i could bring it back to place i got it at and not inform them of the s.ware upgrade that caused the problem to see if they can replace it or something...
just an idea, coz at the moment im kind of stuck.
Hi ...
If you managed to reinstall the ROM through SD card, does it mean you have a bootable system but the RSU doesn't work ?
If so and you can access the XDA from Activesync, then you may locate the 4 files of the RSU upgrade from the \windows\startup directory ... delete them then a hard reset may flash the original RSU back if it's not screwed up.
it should be possible to flash the rom via sd, as i can dump the faulty one to sd and then back over.. so, that part of the bootloader works.
ill ring the place ig ot it at and see what they can do, as it just "went off, all by itself"
i would try the sd flash myself but i aint got a card reader for sd.. just smart media.. lol
it doesnt sound as bad as some peoples s.ware problems however, as the bootloader seems to work ok.,. so fixing it may be possible, but ill give place i got it off a ring first.
thanks for all the info.
If it is under warranty and using the official flash upgrade destroyed the gsm radio stack then O2 should repair or replace. Radio stacks are very difficult to repair and people have asked about getting it fixed only to be told the mainboard needs replacing at huge cost.
thanks for the info, i got a sd card reader, but when i put the thing into pc it asks to format it so it wont read the stuff ive dumped from xda to the card..
oh well, ill give these guys a ring to see what they can do.
where can i get hold of the files to put to the sd card?
ive got the rom/radio files, but they are pc exe`s and not seperate files..
well, i got it flashed ok using official 3.17 s.ware via sd card..
on powering up, it still fails, just white screen with blue top, although there is a keyboard icon on the bottom right which was not there before.
still get gsm error on bootloader..
if only there was a way to put new radio stack on it via sd
djkus said:
well, i got it flashed ok using official 3.17 s.ware via sd card..
on powering up, it still fails, just white screen with blue top, although there is a keyboard icon on the bottom right which was not there before.
still get gsm error on bootloader..
if only there was a way to put new radio stack on it via sd
Click to expand...
Click to collapse
Dead phone, you need send service center to repair, or to me
Does anyone know where I can get my Cingular Wizard fixed? My phone froze one time, and I had to take out my battery and after that I was unable to boot up again. Is there a HTC place in hong kong that does that or in NOrth America?
Thank you for reading my post.
my too , is there any solution if we know that the problem or cause is software and not hardware ,,,, and thanxxx.
s.O.S upgrading to wm6.1 made my wizard brick
while upgrading to wm 6.1 from wm 5.0 , i had a g4 device my device is now not even showing the charging light neither responding or booting.
i haD A G4 DEVICE AS CHECKED WITH WIZARD SERVICE TOOLS, THEN I DID A CID UNLOCK VIA LOCKIWIZ 0.2B , LATER I UPDATED THE IPL/SPL TO 3.08 AND THEN PROCEEDED FOR SNN 3.08 FULL VERSION 6.1 WM6 UPDATE,
THE DEVICE WENT QUIENTLY TO BOOT LOADER MODER I SUSPECT AS THE RAINBOW SCREEN WAS NOT SHOWED ON THE DEVICE THOUGH
HOWSEVER IT WAS SHOWING AS ONLY UPDATING BAR WAS SHOWN WITH ZERO PERCENT UPDATE FINISHED ON THE LAPTOP SCREEN NO RESPONSE ON DEVICE AND THEN A RECOVERY SCREEN APPEARED WHICH PROMPTED TO REMOVE THE BATTERY AND REINSTALL AFTER A FEW SECONDS BUT TO NO AVAIL,
ITS MY BROTHERS PIECE AND I AM VERY SCARED NOW PLEASE HELP ME FROM THIS MESS PLEASE.
loginvicky said:
while upgrading to wm 6.1 from wm 5.0 , i had a g4 device my device is now not even showing the charging light neither responding or booting.
i haD A G4 DEVICE AS CHECKED WITH WIZARD SERVICE TOOLS, THEN I DID A CID UNLOCK VIA LOCKIWIZ 0.2B , LATER I UPDATED THE IPL/SPL TO 3.08 AND THEN PROCEEDED FOR SNN 3.08 FULL VERSION 6.1 WM6 UPDATE,
Click to expand...
Click to collapse
If you really had a G4 device and you did all of the above then you have bricked it. G4's cannot be CID Unlocked via lociwiz (unless something recently changed), and flashing IPL/SPL 3.08 is NOT compatible to a G4 device and that will brick it.
Sorry, but you shouldn't flash a phone (especially if its not even yours) if you don't understand what you are doing. Without further details (and please don't use all caps. I don't care how "scared" you are) there is nothing else anyone here can do to help you. You need to give complete details of what the phone does now. If you can get to (and see) the tri color screen, then its probably recoverable. If the phone won't turn on, then its probably bricked.
Can I ask why you were flashing your brother's phone? Did you have permission?
g0dblissyou said:
Does anyone know where I can get my Cingular Wizard fixed? My phone froze one time, and I had to take out my battery and after that I was unable to boot up again. Is there a HTC place in hong kong that does that or in NOrth America?
Thank you for reading my post.
Click to expand...
Click to collapse
Like my previous post, how about some details. Does the phone go to the Bootloader (tri color) screen? If it does, what are the numbers and info on that screen?
I loaded some huge apps to my storage card tried to use the app. which froze my device. the wizard turns on. but shows the first screen with the phone info. then the second screen that say windows mobile. but it always stay on the second screen
I'd just use the terra thing to format it completely and reflash to a new rom
My heads spinning from all the information aka post and threads, but im still stuck like my wizard on the 2nd splash screen.
I wasnt trying to upgrade the rom jst clear storage but after everything ive read i would like to upgrade to wm6 but first i want to get my wizard working.
I tried backing up the rom to the sd card but I get "You didn't get the proper security level to download a specific image" So i take it my wizard is cid locked.
My IPL:1.01 and SPL:1.06 does that mean its a g3. My activesync 4.5 doesnt pick up my wizard is it because it cant boot, i tried with it in bootloader mode still doesnt pick it up.
So plz point me in the right direction to fix my wizard
ok i think the place where im stuck at is cid unlocking my wizard with out using that imei site. any help or is there another way to do this.
This helped me when I was stuck on the first screen. For some reason, the Radio file was gone. Follow this exactly, it works. In my case (sounds like yours also), at the end of this you will at least have access to the phone again.
http://forum.xda-developers.com/showthread.php?t=276963&highlight=bootloader
After your done. You will have a RGB screen, then follow these directions to load a base rom and unlock so you can keep going until you ca load WM6.1.
http://wiki.xda-developers.com/index.php?pagename=Wizard Windows Mobile 6 for newbies
I've had many, many problems over the last 3 days trying to do this. I completed it all in less than a day, but when I used the phone it had terrible reception. I completely downgraded everything back to square one. Still bad phone reception. I was about to through it out the window, when someone called my wife's cell phone and she also had bad reception. I then put my sim in another phone, same problem. Well, at&t has a tower down for the last 3 days. What timing, it seems to work when not at home, but hard to test that way Anyway, moral of the story is. Don't give up, keep plugging along.
Good luck.
I'm pretty sure imei checker is for SIM unlocking.
For G3 CID unlocking and upgrading read the stickies in http://forum.xda-developers.com/forumdisplay.php?f=289
If you can start your Wizard in bootloader, and it says "usb" in the lower-left, you can flash your original ROM. An active sync connection is not needed. Search for your carrier's ROM if you don't have it and I'd recommend the "no carrier ID" version of the RUU.
Have you tried a 'Hard Reset',hope it'll work,if it boots up into working OS and it already has IPL/SPL 1.xx,use lokiwiz02b tool to SIM/CID unlock the phone and than upgrade.
If it doesn't work still after Hard Reset,most probably,its Extended_Rom is corrupted,its required to reflash a new rom.
Activesync doesn't work in absence of a working OS and in Bootloaders mode.Its not required for flashing a rom.Just get the phone into Bootloaders and hook the phone with pc via usb cable and watch small usb appear at the bottom of the bootloader screen,if its there,it good to go and flash the rom.
ok so i downloaded the button rom finally but how do i flash it to my wizard.
Get your phone in Bootloaders,hook up the phone with pc via usb,watch small usb appear at the bottom of the Bootloader screen,if its there run the 'RUU' application,it'll start to flash,it stops at a certain percentage,don't get worried and do anything,after a couple of minutes it starts again,let it complete 100%,the phone'll restart and boot up in new OS.
which ruu application. I jst downloaded 1 which comes in the form of a rar file saying ruuwrapper. is that the right 1
So after lots and lots and lots more reading i realized i dont need a ruu. all i need to do is get into bootloader mode plug in the usb and run the wizard button rom. It worked perfectly my wizard is back to life yip pee.
Anyway i wud jst like to thank u guys for all the help and compliment u guys on a gr8 forum.
Now my next challenge is wm6 with touch flo.
I unlocked a Cingular 8125 and went to load TNT Professional ROM. The phone kept losing communication at 99% and when I went to reload the original ROM from HTC's site, now I have NO O/S. I DO have another one, but my wife is using it until we get her a pink BlackJackII. I really like these phones, and can't believe I crashed this one! I don't have any Mini-SD cards. Any way to rebuild this thing?
Nobody has any ideas for me? I really need to get this phone running again!
Your not using Vista are you?
Most comm errors are due to weak or discharged battery,not having enough juice to complete the the flash,get it fully charged and try again,secondly,Yes! don't use winVista.
Download the official stock rom and flash to recover back.Get the phone in Bootloaders (RGB screen) hook up the phone and watch small usb appear at the bottom of the Bootloaders,if its there,run the rom to flash,it'll start to flash,but if small usb is not present than most probably its a comm fault.
I was using a Win2K machine. I had 2 batteries that were fully charged. I have a friend that will lend me his miniSD adapter and use my 1gig microSD card to get the info off my wife's phone and copy it to this one. He has a Sprint version of the AT&T Tilt. Might see if he wants to check out this site.
OK. I have access to a miniSD card now. Do I just take my wife's 8125, make a backup from it, then put the card in the bricked phone and load bootloader?
Read this thread for more specific instructions :-
http://forum.xda-developers.com/showthread.php?t=276963
But this method will only work if both the devices are already CID unlocked.Secondly,most important,both the devices shud be of same DOC Chip version,G3 or G4.If you back up a rom of G3 on a G4 device,it'll brick it and vice versa,make sure both the devices are of same DOC Chip version.
They are both G3's. I think they may even be from the same batch. If I unlock hers, won't I lose all her data?
YUP ! but first make a back up of all the personal data on her phone to your pc,for this use either 'PimBackup' or any similar back up application and than unlock it.Its necessary to have both phones CID unlock,otherwise,this method won't work.
OK, I used Lokiwiz 3beta and superCID unlocked the other one. When I run mtty, and use the r2sd all command, I get
R2SDBackup()-Download type=5
usTotalBlock= 1 sizeof(SDCARD_SIGNATRUE_TABLE)=512
I have left it sitting there for an hour and nothing else happens. Isn't it supposed to have several more lines of text scroll by? Also, I can't figure out how to get the dead one to boot to the miniSD.
ok,did you read the method carefully,the link I posted above ? you are getting it correctly.
This methods involves many steps.
Step 1.
Back up all the data on your wife's phone to your pc with 'PIMbackup',than downgrade to IPL/SPL 1.xx either through flashing 'Button's Rom 1.05 or you can even flash official stock rom Aku1 for this,when getting IPL/SPL 1.xx either way,apply lokiwiz02b and not lokiwiz 3beta to CID unlock your wife's phone,or you can use WST_4.2.2 tool also to CID unlock it,but its must to have IPL/SPL 1.xx to CID unlock in both the ways.Only after getting the phone CID unlocked,you can Backup the rom on a miniSD card.
Step 2.
After successfully back up of the rom on miniSD card,insert this card in your dead phone and get the phone into Bootloaders mode (RGB screen).
Step 3.
Run the MTTY command to back up from miniSD card.This is only possible if you already have this phone CID unlocked,otherwise it won't work.
Both the devices must be CID unlocked.
Although,I'm still not sure if it works,but there's no harm to try,may be it gets going.
Is the progress bar supposed to change back and forth from blue-green to red while flashing?
YUP ! it changes during flash,but it'll become green on 100% completion and the phone reboots.
OK. I can't get this thing to take the WizardLove ROM, can't find Button's ROM, but I am trying to load the XDAMiniS ROM now. On my third try and the SPL still says 2.25. Battery is fully charged and I get an immediate connection failure trying to load WizardLove. I really wish I could find the original Cingular ROM for this phone, not the new(er) update.
Download Cigular official stock rom from here :-
http://www.htcamerica.net/support/8125/software-downloads.html
or
http://download.america.htc.com/RUU_Wizard_225111_22511102_022511_CWS_WWE_Ship_1.exe
Check out this link for all the Roms like Buttons Rom T-mobile 2.26 etc
http://wiki.xda-developers.com/index.php?pagename=Wizard Windows Mobile 6 for newbies
I am just about ready to give up on this thing. No matter what I do, when I try to boot it up regular, it still keeps freezing up and when I try to do a hard reset, I get a format is failed error message.
Last ditch effort
Can I use WST to make a backup RUU from the working phone and flash that to the dead one? All other attempts have failed to restore this phone.
I dont think so
Men you are already doing everything!!!
Does you have mtty... try this please it may works for you let us know what happend please...
http://forum.xda-developers.com/showthread.php?t=420785 the man in this thread stucks on splash screen so read just the mtty steps.
BTW does you unlock your wife's phone... is yours unlocked too? before do it...please respond.
The hope dies at the end!!!!! we have so much to´pics about this issue... why you are runing windows 2000? nad make upgrades? or does I missunderstood? extremely recomended Win XP.
I have Vista at home, and I read where many people here say that you can't do reflashes with Vista, so I use my computer at work, which runs Win2K. I haven't unlocked the second phone, but I thought that I did the first one. That was why I went to flash it. I wonder if the unlock didn't take and that put me in this predicament.
I understand now
Maybe a mistake using windows milenium or 2000 or whatever...
So if it say format failed i cant imagine other thing that do the thing i post you... so if you got questions about clear DOC Chip ask everything...
when you already get everything in a XP machine tell us please oh just for a recomendation unplug the minisd and during the process the mtty working on some lines dont launch programs check your USB cable maybe with a little scratch and moving makes a false contact at all.
Hi there, I've been reading the forum for about a week trying to find a fix for my deceased orbit xda.
Problem started when the phone started crashing, the screen was going white and needed re-starting. Eventually it failed to load and froze at the blue screen with the red writing!
so I started reading and tried soft and hard re-booting to no avail.
I have managed to get the phone into bootloader and connected a USB
it recognises the usb and installs as a mobile device on my laptop but here's where it gets tricky. I dunno alot about phone's and am struggling to understand some of the processes. I have tried booting off the SD card but it said invalid certificate (i used the artiemg.nhb file from rapidshare)
I have all the original paperwork and cd's for the phone but dont know what or how to flash a ROM.
what do I need and more important how do I do it without all the tech talk.
Its a WM5 phone - thanks
EDIT - Just to clarify, have just tried the romupdateutility on raving_nanza's sig but recieve an error - am running vista on my laptop
Update, I managed yesterday to get the phone to boot from the SD card and indeed it flashed it and WM5 is back up and running, the new problem is its network locked (to O2 i presume). I was using this phone on orange previously without an issue????
any Idea's other than paying imei check?
...
danv6saxo said:
just tried the romupdateutility on raving_nanza's sig but recieve an error - am running vista on my laptop
Click to expand...
Click to collapse
what link was it?
what error did you have?