Hi all
I can't connect my Polaris through usb anymore. Nothing happends when I connect the cable. It starts to charge but that's all.
I've flashed my Polaris twice(with 2 different roms from this forum) now since I noticed the problem, using the "micro-sd way" but nothing helps.
"Disable advanced network functionality" didn't work either.
I'm starting to think it's a hardware problem but I can't send it to warranty-repair because I don't have the original rom and I can't flash it back to the original Spl because this can only be done through usb.
But it's still chargering fine when I connect the usb cable so there is some connection still.
Btw., when I put the phone in bootloader mode it says "serial" in the bottom of the screen and it doesn't change to "usb" when I connect the usb cable but my PC pops up a message that says "Usb device not recognized" and under "Device manager" is says "Unknown device". I've tried another cable and another computer but nothing helps.
Any help???
Same happened to me!
I flashed udk r6 rom from SD card after it i could sync from USB normally,
Then i flashed the same rom second time for clean install - again using SD and now i cant sync through USB only through bluetooth...
I thinks its some bug not HW failure maybe uninstall drivers (i use vista btw) and install again?
I've tried uninstalling Activesync and download a new "setup" file and the install activesync again, but this didn't help.
I hope that the problem is software related because if it's hardware related i can't get it repaired through warranty...
Hello, it happend to me to. It just wan`t unlock. It wan`t hard spl. or go into usb mode, only soft reset works. No warrenty, so it will stay in the locker. AS don`t recognaise it. I have the Glass rom, and there where never any problem with it.
Per
It could be a bad contact at the mini-usb connector as it happened to me. Try another cable or push firmly the connector.
maag said:
It could be a bad contact at the mini-usb connector as it happened to me. Try another cable or push firmly the connector.
Click to expand...
Click to collapse
I have already tried another cable and pushing the connector firmly but nothing helps.
I don't understand it because my wall-charger works fine and my headset works fine also. The only thing that doesen't work is acticesync...
exactly the same problem here. after upgrade to r6 and a radio upgrade to murata through PDM activesync no longer works. furthermore the computer doesn't even respond to the phone being plugged in. i had the same response in bootloader mode of not being recognised, but try as i might it will not respond when turned on!
Very frustrating as cannot connect to pc (xp) in anyway.
ICS will not engage as it says "check usb cable connection"
Has anyone moved any further with this issue? i had some issues with the phone being stuck in a bootloader cycle after a radio upgrade but after much angst a Hard reset (and removal of the presumed offending microsd card) solved this!
Read a kaiser thread on possible failure of the microusb connection, specifically the 'B' connectio but elevation of this pin proved fruitless. anyone have any pearls of wisdom on this one?
Try this and it might work...
Start -> settings -> system -> USB to PC
Disable "Enable advanced network functionality".
Related
hi - as many of you will know the xda experiance can be an all consuming task .
i after reading many many posts would like some information on how exactly to get the mtty tool to offer me the option of usb so i can connect to my bricked xda exec.
my bootloader screen is severely distored in colour however i can get back and forth to the promt for "press x or 0 " to reset / exit. it seems this proble m is not unknown however i dont seem to be lucky when it comes to the mtty tool.
any help would be greatly appreciated : thanks in advance.
Did you disable Activesync on your PC first?
Find the (two) executables in taskmanager and end task.
V
True. And make sure you're not running Vista! (bricked my phone for a few days until I could fix that)
snorbaard said:
True. And make sure you're not running Vista! (bricked my phone for a few days until I could fix that)
Click to expand...
Click to collapse
would you share HOW you sorted vista bricking your uni? i've had to send it for repairs because nothing i could do fixed it.
i tried updating the firmware to another of helmi's cooked roms. i've flashed the device many times and used all sorts of people's roms, and i think it was the time i switched to VISTA that bricked it.
My solution
Take the sd card from the phone... duh
It was giving the same error, when i took the card it started to work...
ohmlogic said:
how do i get usb in drop down in mtty tool ?
Click to expand...
Click to collapse
Strange, I never have a problem with the sd card or sim card in the phone
[1]
First make sure active sync is not running, you may have to kill the process wcescomm.exe (CTRL+ALT+DEL, Processes TAB, right click on process and End Process Tree)
[2]
If that doesn't work, change the usb cable, every time i encounter that problem - it is nearly always the usb cable, if you have a canon digital camera, those cable works for me about every time
No man... i've been tryin to get USB in dropdown list but never appears. I'm so tired of incomplete answers. I'm using vista and i kill every process indicated by you.
Did you or did you not post multiple threads on the same problem?
Try this instead of mtty.
http://handheld.softpedia.com/get/System-Utilities/nueTTY-Console-71189.shtml
Its a console that diables everything automatically.
It worked a treat for me. My phone was stuck in bootloader.... no ROM or SPL would flash (stuck at 0%) I couldn't get mtty to give me "USB" from the dropdown in Vista.
I can't get into the boot loader so it says "USB" in the bottom white area... even though USB cable is inserted, of course. If I boot up with device with USB cable inserted the only thing that happens is that the white area is blank. When unplugging the device "Serial" is written, but plugging the USB cable back in doesn't change a ****... stills says "Serial"...
Any clue, USB connector defective? Tried two cables.
nueTTYConsole says the following:
Code:
Disabling RAPI...Already Stopped!
Searching for CE USB devices to connect...
No devices found to connect, aborting...
Not restarting RAPI because it was already disabled.
shadeyhk said:
If that doesn't work, change the usb cable, every time i encounter that problem - it is nearly always the usb cable, if you have a canon digital camera, those cable works for me about every time
Click to expand...
Click to collapse
WOW!! after 2.5 hrs all I had to do is change the cord. hats off for the solution.
My friend's jamin when he tried upgrading with smart1 wm6
after the flashing process finished it gives the 3 colors of boot loader
the screen flickers continously with the 3 colors
no way to hard reset the device
and activesync doesn't feel it
I searched all the forum for a problem like this but I didn't find any
any suggestion please, or any help?
Flash NVID Rom and try Smart again. Read WM6 upgrade Manuel and readme for the ROM.
NetrunnerAT said:
Flash NVID Rom and try Smart again. Read WM6 upgrade Manuel and readme for the ROM.
Click to expand...
Click to collapse
Please how can i flash with the activesync doesn't notice my device and where's NVID Rom
Ok. I'll search for it but please help how can I flash it to the device which doesn't recognized or felt by PC
If your device is in bootloader mode, activesync cannot recognize it but this is normal. Jamin is recognize only as a usb device and you can downgrade it to NVID rom easly.
Then you could upgrade your favorite rom, I suggest PDAVIET 4.0.0.1
Bye for now
divxmaniak said:
If your device is in bootloader mode, activesync cannot recognize it but this is normal. Jamin is recognize only as a usb device and you can downgrade it to NVID rom easly.
Then you could upgrade your favorite rom, I suggest PDAVIET 4.0.0.1
Bye for now
Click to expand...
Click to collapse
I think I didn't discuss the problem well
The Problem is when I start to flashing a rom a message tells that check if the usb is connected and if the device is connected .
This is happen with the device is connected to the cable and the tricolor screen is flicking . and the device doesn't open doesn't flashing.
must use NVID rom. maybe qtek nvid one from here? http://wiki.xda-developers.com/index.php?pagename=Prophet_ROMs
hasanemara said:
I think I didn't discuss the problem well
The Problem is when I start to flashing a rom a message tells that check if the usb is connected and if the device is connected .
This is happen with the device is connected to the cable and the tricolor screen is flicking . and the device doesn't open doesn't flashing.
Click to expand...
Click to collapse
If the problem still there, Try to release the battery for 1-3 hours and put it again to the device, go to the boot loader and pray. Hopefully it could work. Actually, this way worked on my Himalaya and Prophet.
Just run the "Step 1" component of the PDAViet ROM (http://rapidshare.com/files/32728615/Prophet_PDAViet_Step1.zip), which is just a plain AKU 2.20 NVID. This will find your device even if its in bootloader mode (it doesnt depend on activesync). Just flash it with that sucker and you should have a working phone on WM5, then you can safely upgrade it to WM6 (or leave it if you like).
ekto said:
Just run the "Step 1" component of the PDAViet ROM (http://rapidshare.com/files/32728615/Prophet_PDAViet_Step1.zip), which is just a plain AKU 2.20 NVID. This will find your device even if its in bootloader mode (it doesnt depend on activesync). Just flash it with that sucker and you should have a working phone on WM5, then you can safely upgrade it to WM6 (or leave it if you like).
Click to expand...
Click to collapse
I shall try and tell you the result
error 260 this is the result
i have a slight variation problem like this...
1. i was upgrading my O2 Neo to the latest WM05 & the phone went to bootloader mode & the upgrade started searching for the phone as normal..then some error & it stopped upgrading while the phone was in bootloader mode..
2. at that time,i got an urgent call & had to leave the phone in bootloader mode...
3. when i came back..the phone was dead & now it wont startup at all.. not even in the bootloader mode.
4. Maybe the batteries dead...so i charged it (Over night)..nothing happened in the morning..
5. kept the battery removed for about 5-6hours & still nothing happens..it simply does not startup.
6.I've tried holding the camera button & resetting, but it wont go into bootloader mode.
7. i;ve tried holding the connections button + camera button _ reset but it wont hard reset...
can anyone help me here...
what can i do???
hasanemara said:
error 260 this is the result
Click to expand...
Click to collapse
Error 260... If i remember correctly that's "cant find device" or something.
Few things to check:
Is the PC you are upgrading on running windows vista?
If so, use a different PC running windows XP.
Have you tried a different USB cable?
If not, do so, this tends to be the cause of problems like this.
Have you checked device manager?
Go to control panel, Administrative tools, computer management, device manager and see if you can find your device. If it has a yellow ! icon on it or is listed as "Unknown device" or anything like that then you may need to reinstall the drivers (int hsi case the easiest way to do that is to reinstall activesync). If everyhting is working properly it should show up as "HTC USB Sync", "PocketPC USB Sync" or something like that under the heading "Mobile Devices".
Have you just plain tried another computer, regardless of the OS?
I found that I could never get my phone to flash on my laptop, but it worked without a problem on my desktop. This is not to say laptop's cant do it, it simply means some computers just have problems like (in my case i believe) no USB 2.0, or too low-powered USB ports.
ekto said:
Error 260... If i remember correctly that's "cant find device" or something.
Few things to check:
Is the PC you are upgrading on running windows vista?
If so, use a different PC running windows XP.
Have you tried a different USB cable?
If not, do so, this tends to be the cause of problems like this.
Have you checked device manager?
Go to control panel, Administrative tools, computer management, device manager and see if you can find your device. If it has a yellow ! icon on it or is listed as "Unknown device" or anything like that then you may need to reinstall the drivers (int hsi case the easiest way to do that is to reinstall activesync). If everyhting is working properly it should show up as "HTC USB Sync", "PocketPC USB Sync" or something like that under the heading "Mobile Devices".
Have you just plain tried another computer, regardless of the OS?
I found that I could never get my phone to flash on my laptop, but it worked without a problem on my desktop. This is not to say laptop's cant do it, it simply means some computers just have problems like (in my case i believe) no USB 2.0, or too low-powered USB ports.
Click to expand...
Click to collapse
No I didn't change any and I can connect my o2 xda mini to the same cable
I want to ask few technical question
HOW CAN A SOFTWARE DAMAGE THE DEVICE?
CAN A SOFTWARE FOR EXAMPLE BURNS A PROCESSOR OR SOMETHING LIKE THIS?
If So there will be a big problem with those types of devices
a virus for example can destroy my device's board or processor!!
Yesterday My friend went to an I-mate customer service who tel him that
the board had been destroyed by the bad software !!!!!!!!!
Please Give me technical advice about this problem
and is there a web site for him to buy this board (i-mate jamin)?
I've tried everything... even tried it on my desktop... but my phone just wont turn on now. i've kept the battery removed for more than 8hrs now... i've even charged it for more than 8hrs non-stop..nothing happens..
maybe i should get hold of a charged battery & try it with that battery...?
Any clue how to get my phone started??
got it working !!! PHEW... i used my HP battery which was charged & put it into it..now i've got my bootloader & i'm installing the new OS as we speak... 15% done.... keeping my fingers crossed
done.. got my HP Ipaq battery , which was charged & my new started up in bootloader more.. PHEW !!!
66% done... keeping my fingers crossed
ok, installed...now, one more problem..my touch screen's not working...???
Any idea what to do?
i installed "Prophet_PDAViet_Step1"
I have my hw6915 with the screen " Serial HP Invent vG.30". I have tried various fixes for this but dont work. Activesync dont connect, UNI_ExitBootloader say that "Cannot open USB port". If i use hpRUU.exe for flashing the rom it say than can´t connect. I am using windows XP sp3. What might be the problem?
Could be that showing on screen "Serial" the only mode for works is RS232 and no USB?
It should say 'Serial' until you plug it into the USB Cradle, from that moment on it should say 'USB'.
Then again you can use the UNI_ExitBootloader proggy to get ride of this screen.
The problem is that when i plug it into the usb cradle dont change to "USB" it still saying "SERIAL"
Indeed, thats bad.
Maybe reset it and try another Cradle from a friend or so. Else check that the USB port itself is clean from dirt.
If it doesn't work in another USB-Cradle i guess it's broken somehow
Yes, i have test the cradle connector and it have two pins broken, i have used other and it work perfectly, i have used the UNI_ExitBootloader.exe and i have the PDA working again, but the GSM dont work, i have seen the configuration of the GSM and all data is empty, Firmware, IMEI, protocol,etc, i think that Radio ROM is corrupted. I try to update with the new official Update in Spanish, but ther is a failure and the pda be stalled when I reset it back to bootloader. I have try some times and always the same. How can i update the Radio rom my CEOS is in Spanish?. Thanks
I have universal and a few days ago i accidently flashed radio rom 1.18 into it. Now when you try to turn it on it just shows startup logo sayng NO GSM and radio rom version. When i start it in bootloader it says SERIAL, and when i connect usb cable it still says SERIAL, it doesn't switch to USB? I found out that if you have already connected the cable BEFORE you go into bootloader, it will change to USB, but the pc doesn't seem to recognise it. Instead it says UNKNOWN USB DEVICE? Please help me, i have tried almost everything, but no succsess. Is there some serial cable schematics or something like that? I tried connecting COM cable to mini USB connector, and when i go to bootloader mtty gives me phone info {phone type, lcd display type blah blah} but i can't write anything, like my keyboard is disconnected. Or maybe my com cable was broken, i don't know?
Accidentally?
Welcome to forums
Have a read here:
http://wiki.xda-developers.com/index.php?pagename=Uni_Stuck_Bootloader_Serial
Try to reinstall another ROM
Hope it helped,
Hi ATRAC3,
i had the same problem. Flashed a Radio. Though i'd Bricked my uni.
The problem i found was i left my SD-Card in, After taking it out. I re-Flashed, And the ROM re-installed XD
So my adive is. Try taking out ur SD Card
Hey, small problem here. I was charging my HD2 earlier today with no problems at all, I flashed the 1.72 stock ROM back onto my phone, and it seemed to be charging fine for a small while after that. But now, after I tried charging my phone, it doesn't seem to recognise there's a USB connection at all. The LED at the speaker-grille isn't doing anything, and the the phone tells me it isn't connected by USB when it's plugged into a computer.
I tried a tonne of things, checked the cable and switched it, soft-reset it, took the battery out, hard reset it, and even blown inside the socket to try and get rid of anything that might be blocking it, but it just isn't showing it's plugged in AT ALL any more... and now the battery is dead, so I can't do anything with it now to try and help it. :/
The only sign I have that the phone realises it has any sort of USB connection, is when I tried to hard reset the device, (I used the hold volUp+volDown+Power method) and it shows the message 'press volUp to hard reset,' usually when I do this, pressing volume up doesn't do anything when the phone is connected by USB for some weird reason - and I have to disconnect USB for the phone to hard reset. I figured this wouldn't happen if the phone doesn't realise it has a USB connection, but when the cable was plugged in, it still wouldn't hard reset until I took it out. So it shows there must be some way the phone knows it's connected.
I'm running the WWE 1.72 ROM with radio 2.10. 50.08_2 if it helps.
Any suggestions?
*Bump*
Sorry for the bump, but it would really help if anyone could help explain this.
I think a bit of trial and error would be best here to establish whats at fault.
phone, cable, or usb port.
-try plugging into a different usb port
-try a different cable (if you have one)
appologies if you have tried these allready.
Tried another cable again just incase, still nothing though. My iPods connected via that USB port I tried using, and that's working fine, so it doesn't seem like that's it, either...
Hi:
I'm having a similar problem. I had plugged in a new retractable usb cable, and when I did, the phone shut off. I rebooted, and tried my original cable, but the phone doesn't charge or sync. I've also tried hard/soft reset, wall charger, usb charger, and none of that seems to work.
Any suggestions?
Thanks.
No idea if this is related or not but my USB connection stopped working after I got the "bttrayce.exe is not a valid pocket pc application" problem (Thanks TomTom! ) so it would appear the USB port has some weird dependencies!
Fixed it by renaming the windows\btsdkce30.dll file (added "[temp]" to the name just in case!) and soft-resetting.
Might be worth a try?
r u using activsync or windows mobile centre ???
USB Issue
I've got exactly the same issue, running HyperROM 3.01.405.T1 and Radio 2.06.51.07.
Suddenly USB isn't working, tried various cables and I suspect it's a software issue somewhere.
Charging isn't a problem at the moment, I have a charging station (ebay from Hong Kong) so I can access the phone and try and resovle this.
I'm going to go back to the stock rom (I assume I'll find that somewhere on XDA) and upddate the Radio version and see if that sorts it.
If anyone has worked out what's casuing this generally let me know as I can imagine this will take a lot of trial and error to solve!
Thanks
have you fixed it?
i am having a similar issue:
I have recently updated my HTC HD2 rom to version 3.14.410.2.
After that i have installed tomtom navigator, but when i turn on the device it returned a message 'BTTRAYCE' is not a valid Pocket PC application'.
I looked at the forums and it was recommended to delete files Windows\BtSdkCE30.dll and
\Windows\BtCoreIf.dll, so i did.
Unfortunately my usb connection is now not working, and i think it could be related to the deletion of those 2 files.
I made a hard reset, but the problem still persists.
can anyone help me please?
My problem solved
Hi i got the same problem , i use ARTEMIS 48 rom 3.14. so my phone suddenly droped to the ground last night but i was charging after that .... next days morning i wanted to connect it to my pc via activesync but it dose not connect .... even disk drive did not work and i could not charge it via AC CHARGER and PC , i toyed around with it here is what i did
1- tried on another pc (result wass the same it did not worked)
2-i hard reseted it (result = the problem was not solved )
3-i went to setting>>>>system>>>power>>>battery and unchecked the option "when phone is on , do not charge ...."
4- i connected it to pc it was not recognozed by pc but it was charging !!!!!!
5-after that i connected it to AC ADAPTOR and it was charging !!!!!!
6- i decided to flash my rom and do a HSPL so my phone will not brick so i connected it to activesync via bluetooth and it was as sucess
7-mean while i was searching this forums
8- i checked my SPL ver
9- i soft-reset and stuning it was recognized by pc and everything was back to normal
in my XP i think it was due to BAD ASS ANDROID ROM and some custom roms bugs....
fpcraveiro said:
have you fixed it?
i am having a similar issue:
I have recently updated my HTC HD2 rom to version 3.14.410.2.
After that i have installed tomtom navigator, but when i turn on the device it returned a message 'BTTRAYCE' is not a valid Pocket PC application'.
I looked at the forums and it was recommended to delete files Windows\BtSdkCE30.dll and
\Windows\BtCoreIf.dll, so i did.
Unfortunately my usb connection is now not working, and i think it could be related to the deletion of those 2 files.
I made a hard reset, but the problem still persists.
can anyone help me please?
Click to expand...
Click to collapse
Uninstall TomTom and the problem goes away.
You can download versions on TomTom Navigator 7 with the Bluetooth files removed - like * HERE *
I don't have an OS installed...
This is due to aMAGLDR being installed and when I had the device open.. I created a 'temp' folder and my next task was to create a 'create_to_sd_root', well I renamed the temp folder to that... bad move? I think so. My system acknowledges the device, however I'm unable to access it. I.e. my computer(no icon), windows mobile center(not connected), etc. Please help! I need my phone!
MrHellas said:
This is due to aMAGLDR being installed and when I had the device open.. I created a 'temp' folder and my next task was to create a 'create_to_sd_root', well I renamed the temp folder to that... bad move? I think so. My system acknowledges the device, however I'm unable to access it. I.e. my computer(no icon), windows mobile center(not connected), etc. Please help! I need my phone!
Click to expand...
Click to collapse
I you were trying to flash Android you just need to flash Clock Work Mod (CWM) and then place the .zip file for the Android ROM on your SD card and use CWM to flash the Android ROM. It is links to Youtube videos in the OP of the thread showing you how to flash CWM and the ROM.
Are you could flash back to Win MO through USB and bootloader or SD card and bootloaderr.. If you go for USB and bootloader make sure you see USB in the white bar of bootloader befor tryng to flash the ROM. Also thew SD card metrhod will remove HSPL if you use a Official and not a custom ROM.
Well I've figured out how to get the android os on there, however I'm unable to locate the drivers for AD8? I'm still unsure about what folder/files need to be on my microSD if I'm running the Desire HD Froyo(current) I cannot access any internal/external(microSD). Help?
MrHellas said:
Well I've figured out how to get the android os on there, however I'm unable to locate the drivers for AD8? I'm still unsure about what folder/files need to be on my microSD if I'm running the Desire HD Froyo(current) I cannot access any internal/external(microSD). Help?
Click to expand...
Click to collapse
You have to use MAGLDR's mass storage option to get access to your SD card, or use the mount storage option in Clock Work Mod. I recomemd usingvthecnass storagecin MAGLDR though as I have had trouble gettingvthecdrivers for mount storage in CWM to install but have never had a problem with the mass storage option in MAGLDR.
T-Macgnolia said:
You have to use MAGLDR's mass storage option to get access to your SD card, or use the mount storage option in Clock Work Mod. I recomemd usingvthecnass storagecin MAGLDR though as I have had trouble gettingvthecdrivers for mount storage in CWM to install but have never had a problem with the mass storage option in MAGLDR.
Click to expand...
Click to collapse
How do I get back the loader without booting up? Obviously haven't been able to copy the rar files. Could this be why my GPS and other functions could not be working properly?
imanh said:
3-i went to setting>>>>system>>>power>>>battery and unchecked the option "when phone is on , do not charge ...."
Click to expand...
Click to collapse
Thanks this sorted my problem!
imanh said:
Hi i got the same problem , i use ARTEMIS 48 rom 3.14. so my phone suddenly droped to the ground last night but i was charging after that .... next days morning i wanted to connect it to my pc via activesync but it dose not connect .... even disk drive did not work and i could not charge it via AC CHARGER and PC , i toyed around with it here is what i did
1- tried on another pc (result wass the same it did not worked)
2-i hard reseted it (result = the problem was not solved )
3-i went to setting>>>>system>>>power>>>battery and unchecked the option "when phone is on , do not charge ...."
4- i connected it to pc it was not recognozed by pc but it was charging !!!!!!
5-after that i connected it to AC ADAPTOR and it was charging !!!!!!
6- i decided to flash my rom and do a HSPL so my phone will not brick so i connected it to activesync via bluetooth and it was as sucess
7-mean while i was searching this forums
8- i checked my SPL ver
9- i soft-reset and stuning it was recognized by pc and everything was back to normal
in my XP i think it was due to BAD ASS ANDROID ROM and some custom roms bugs....
Click to expand...
Click to collapse
I did the same but no work. I have issue #USB not recognized# after installed Android Transformer SD ver.
In three color screen I have USB connection working fine. I could install HSPL4, update Radio, but Win 6.5 has a USB problem.
I don't think this is a hardware issue or I am wrong?
Still confused. Should I take my phone to service?
Hi,
I have the similar problem with my hd2, but worse. Out of 3 different comouters I tried none can see the phone connected and gives me the error saying one of the USB device connected to this computer has malfunctioned and cannot be recognized. I have tried two different cables. I cannot connect my phone through latest magldr using USB flasher or USB mass storage modes. Moreover, when I connect my phone in rainbow screen (hspl screen where you install magldr), it should change to USB from serial but even that does not happen. ANy solutions?? I think its my phone.... Is there any way to revert this back to normal. I don't want a brick.
mcdoc said:
I did the same but no work. I have issue #USB not recognized# after installed Android Transformer SD ver.
In three color screen I have USB connection working fine. I could install HSPL4, update Radio, but Win 6.5 has a USB problem.
I don't think this is a hardware issue or I am wrong?
Still confused. Should I take my phone to service?
Click to expand...
Click to collapse
Your USB drivers for the defualt bootloader (multicolor screen) seem to be working fine, so no you do not have a hardware problem. You might want to uninstall Windows Mobile Device Center or Active Sync, which ever one your computer uses. Then re install it. Also go to device manager in your comtrol panel while you have hour HD2 booted up and connected via USB and clck on update drivers for hour phone, it should be listed in device manager.
kushki said:
Hi,
I have the similar problem with my hd2, but worse. Out of 3 different comouters I tried none can see the phone connected and gives me the error saying one of the USB device connected to this computer has malfunctioned and cannot be recognized. I have tried two different cables. I cannot connect my phone through latest magldr using USB flasher or USB mass storage modes. Moreover, when I connect my phone in rainbow screen (hspl screen where you install magldr), it should change to USB from serial but even that does not happen. ANy solutions?? I think its my phone.... Is there any way to revert this back to normal. I don't want a brick.
Click to expand...
Click to collapse
When you say your Serial in boorloader does not change to USB this tells me you are having driver issues or hardware issues with your micro USB port on your HD2. My bet is it is just driver issues. I sugest you uninstall and rei nstall Wimdows Mobile Device Center or Active Sync which ever one your computer uses. These programs contain the USB drivers for the HD2 and MAGLDR partialy relies on those drivers to. So maybe that will solve your problem.