Related
My friend's jamin when he tried upgrading with smart1 wm6
after the flashing process finished it gives the 3 colors of boot loader
the screen flickers continously with the 3 colors
no way to hard reset the device
and activesync doesn't feel it
I searched all the forum for a problem like this but I didn't find any
any suggestion please, or any help?
Flash NVID Rom and try Smart again. Read WM6 upgrade Manuel and readme for the ROM.
NetrunnerAT said:
Flash NVID Rom and try Smart again. Read WM6 upgrade Manuel and readme for the ROM.
Click to expand...
Click to collapse
Please how can i flash with the activesync doesn't notice my device and where's NVID Rom
Ok. I'll search for it but please help how can I flash it to the device which doesn't recognized or felt by PC
If your device is in bootloader mode, activesync cannot recognize it but this is normal. Jamin is recognize only as a usb device and you can downgrade it to NVID rom easly.
Then you could upgrade your favorite rom, I suggest PDAVIET 4.0.0.1
Bye for now
divxmaniak said:
If your device is in bootloader mode, activesync cannot recognize it but this is normal. Jamin is recognize only as a usb device and you can downgrade it to NVID rom easly.
Then you could upgrade your favorite rom, I suggest PDAVIET 4.0.0.1
Bye for now
Click to expand...
Click to collapse
I think I didn't discuss the problem well
The Problem is when I start to flashing a rom a message tells that check if the usb is connected and if the device is connected .
This is happen with the device is connected to the cable and the tricolor screen is flicking . and the device doesn't open doesn't flashing.
must use NVID rom. maybe qtek nvid one from here? http://wiki.xda-developers.com/index.php?pagename=Prophet_ROMs
hasanemara said:
I think I didn't discuss the problem well
The Problem is when I start to flashing a rom a message tells that check if the usb is connected and if the device is connected .
This is happen with the device is connected to the cable and the tricolor screen is flicking . and the device doesn't open doesn't flashing.
Click to expand...
Click to collapse
If the problem still there, Try to release the battery for 1-3 hours and put it again to the device, go to the boot loader and pray. Hopefully it could work. Actually, this way worked on my Himalaya and Prophet.
Just run the "Step 1" component of the PDAViet ROM (http://rapidshare.com/files/32728615/Prophet_PDAViet_Step1.zip), which is just a plain AKU 2.20 NVID. This will find your device even if its in bootloader mode (it doesnt depend on activesync). Just flash it with that sucker and you should have a working phone on WM5, then you can safely upgrade it to WM6 (or leave it if you like).
ekto said:
Just run the "Step 1" component of the PDAViet ROM (http://rapidshare.com/files/32728615/Prophet_PDAViet_Step1.zip), which is just a plain AKU 2.20 NVID. This will find your device even if its in bootloader mode (it doesnt depend on activesync). Just flash it with that sucker and you should have a working phone on WM5, then you can safely upgrade it to WM6 (or leave it if you like).
Click to expand...
Click to collapse
I shall try and tell you the result
error 260 this is the result
i have a slight variation problem like this...
1. i was upgrading my O2 Neo to the latest WM05 & the phone went to bootloader mode & the upgrade started searching for the phone as normal..then some error & it stopped upgrading while the phone was in bootloader mode..
2. at that time,i got an urgent call & had to leave the phone in bootloader mode...
3. when i came back..the phone was dead & now it wont startup at all.. not even in the bootloader mode.
4. Maybe the batteries dead...so i charged it (Over night)..nothing happened in the morning..
5. kept the battery removed for about 5-6hours & still nothing happens..it simply does not startup.
6.I've tried holding the camera button & resetting, but it wont go into bootloader mode.
7. i;ve tried holding the connections button + camera button _ reset but it wont hard reset...
can anyone help me here...
what can i do???
hasanemara said:
error 260 this is the result
Click to expand...
Click to collapse
Error 260... If i remember correctly that's "cant find device" or something.
Few things to check:
Is the PC you are upgrading on running windows vista?
If so, use a different PC running windows XP.
Have you tried a different USB cable?
If not, do so, this tends to be the cause of problems like this.
Have you checked device manager?
Go to control panel, Administrative tools, computer management, device manager and see if you can find your device. If it has a yellow ! icon on it or is listed as "Unknown device" or anything like that then you may need to reinstall the drivers (int hsi case the easiest way to do that is to reinstall activesync). If everyhting is working properly it should show up as "HTC USB Sync", "PocketPC USB Sync" or something like that under the heading "Mobile Devices".
Have you just plain tried another computer, regardless of the OS?
I found that I could never get my phone to flash on my laptop, but it worked without a problem on my desktop. This is not to say laptop's cant do it, it simply means some computers just have problems like (in my case i believe) no USB 2.0, or too low-powered USB ports.
ekto said:
Error 260... If i remember correctly that's "cant find device" or something.
Few things to check:
Is the PC you are upgrading on running windows vista?
If so, use a different PC running windows XP.
Have you tried a different USB cable?
If not, do so, this tends to be the cause of problems like this.
Have you checked device manager?
Go to control panel, Administrative tools, computer management, device manager and see if you can find your device. If it has a yellow ! icon on it or is listed as "Unknown device" or anything like that then you may need to reinstall the drivers (int hsi case the easiest way to do that is to reinstall activesync). If everyhting is working properly it should show up as "HTC USB Sync", "PocketPC USB Sync" or something like that under the heading "Mobile Devices".
Have you just plain tried another computer, regardless of the OS?
I found that I could never get my phone to flash on my laptop, but it worked without a problem on my desktop. This is not to say laptop's cant do it, it simply means some computers just have problems like (in my case i believe) no USB 2.0, or too low-powered USB ports.
Click to expand...
Click to collapse
No I didn't change any and I can connect my o2 xda mini to the same cable
I want to ask few technical question
HOW CAN A SOFTWARE DAMAGE THE DEVICE?
CAN A SOFTWARE FOR EXAMPLE BURNS A PROCESSOR OR SOMETHING LIKE THIS?
If So there will be a big problem with those types of devices
a virus for example can destroy my device's board or processor!!
Yesterday My friend went to an I-mate customer service who tel him that
the board had been destroyed by the bad software !!!!!!!!!
Please Give me technical advice about this problem
and is there a web site for him to buy this board (i-mate jamin)?
I've tried everything... even tried it on my desktop... but my phone just wont turn on now. i've kept the battery removed for more than 8hrs now... i've even charged it for more than 8hrs non-stop..nothing happens..
maybe i should get hold of a charged battery & try it with that battery...?
Any clue how to get my phone started??
got it working !!! PHEW... i used my HP battery which was charged & put it into it..now i've got my bootloader & i'm installing the new OS as we speak... 15% done.... keeping my fingers crossed
done.. got my HP Ipaq battery , which was charged & my new started up in bootloader more.. PHEW !!!
66% done... keeping my fingers crossed
ok, installed...now, one more problem..my touch screen's not working...???
Any idea what to do?
i installed "Prophet_PDAViet_Step1"
I have upgraded from WM2003SE to WM6 (the first released from XPlode version OS 5.2.1620 build 18125.0.4.2) without any problem. Now I want to upgrade from that version to the current release, but the ActiveSync (I am using 4.5) always disconnect after MaUpgradeUT_noID has detected the previous installed OS. So I got an error message like "cannot to the device" or so. It happens everytime even I just try to upgrade the Radio rom.
I have also tried to use ActiveSync to version 3.8 (I found this suggestion from this web site) but bad luck it can't detect my BA device at all. I have also tried to revert back to WM2003SE but still get the same problem. My system is WinXP SP2 & O2 IIs. So Please help I am in the dark right now.
Same problem here...
su2003 said:
I have upgraded from WM2003SE to WM6 (the first released from XPlode version OS 5.2.1620 build 18125.0.4.2) without any problem. Now I want to upgrade from that version to the current release, but the ActiveSync (I am using 4.5) always disconnect after MaUpgradeUT_noID has detected the previous installed OS. So I got an error message like "cannot to the device" or so. It happens everytime even I just try to upgrade the Radio rom.
Click to expand...
Click to collapse
get into boot loader mode,then try
(press record button + power button and reset at same time)
addan said:
get into boot loader mode,then try
(press record button + power button and reset at same time)
Click to expand...
Click to collapse
Have tried that already but still get the same error. I have even reformatted my PC and reinstalled WinXP and ActiveSync 4.5 just in case there are viruses or so but also get no luck.
Did you soft (or hard) reset your BA and reboot your PC after failure? (Try clean upgrade, and in bootloader).
Did you (succesfully) establish an ActiveSync partnership before upgrading?
Did you try unchecking Enable advance network functionality in USB to PC (under settings, connections)?
Did you soft (or hard) reset your BA and reboot your PC after failure? (Try clean upgrade, and in bootloader).
Yes, at this time you asked me. Nothing changed.
Did you (succesfully) establish an ActiveSync partnership before upgrading?
Yes.
Did you try unchecking Enable advance network functionality in USB to PC (under settings, connections)?
Yes. I did it.
More over, if I started BootLoader mode before execute MaUpgradeUt_noID.exe the program get struck while performs device information checking, I have to pull it out from Sync station the program then continue running but without any information (like the existing OS version etc.)
how long did you wait for the program to respond before you find that its stuck ?
Here it takes about 2 min to find the device
Proper upgrading procedure, as it was said 10000's of times
1.put your device in bootloader mode
2. place it to cradle
3. kill activesync (optional - if you dont do it the upgrade utility will do it for you, but sometimes activesync stays on and fail the upgrade process)
4. start upgrade utility and follow the onscreen instructions
5. perform hard reset (the three options thing)
thats all
Xplode's new cube cab
deleted... off topic
how long did you wait for the program to respond before you find that its stuck ?
It was about 5 min and the program still had no responses. I then have to pull it out and the program continue running but without any information (like I had mentioned it before).
Here it takes about 2 min to find the device
Unfortunately not with mine.
Proper upgrading procedure, as it was said 10000's of times
1.put your device in bootloader mode
Yes. I did it.
2. place it to cradle
Yes. I did it.
3. kill activesync (optional - if you dont do it the upgrade utility will do it for you, but sometimes activesync stays on and fail the upgrade process)
I have tried it both with and without killing the activesync.
4. start upgrade utility and follow the onscreen instructions
Yes, but once I started the upgrade I have noticed that the activesynce has disconnected my device.
5. perform hard reset (the three options thing)
I didn't have chance to go to this point.
thats all
I think the main problem is the activesync has disconnected my device suddenly when started the utility. I have also tried to take out anythings that using USB port like mouse, ext. DVD, printer, scanner just in case the upgrade utility may conflicts with those devices.
I think I shall try to change the PC to upgrade my device to make sure that it wasn't caused from hardware defection.
su2003 said:
4. start upgrade utility and follow the onscreen instructions
Yes, but once I started the upgrade I have noticed that the activesynce has disconnected my device.
5. perform hard reset (the three options thing)
I didn't have chance to go to this point.
thats all
I think the main problem is the activesync has disconnected my device suddenly when started the utility. I have also tried to take out anythings that using USB port like mouse, ext. DVD, printer, scanner just in case the upgrade utility may conflicts with those devices.
I think I shall try to change the PC to upgrade my device to make sure that it wasn't caused from hardware defection.
Click to expand...
Click to collapse
With regard to your last remark: you stated earlier you did a fresh reinstall of XP. Now, why would you install and connect all these peripherals if you only want to upgrade your BA rom??? All you need is a fresh WinXP and ActiveSync...
Did you really do a fresh install and follow the wiki and the tips mentioned again (and again)?
You are getting me (and probably all of us) confused.
Your answers to especially points 4 and 5 of xplode tips to me clearly indicate that you do not really take (enough) time to understand the procedures (or what you are doing) and want to have WM6 running asap with no effort at all...
Your remark "I think the main problem is the activesync has disconnected my device suddenly when started the utility" only confirms this as this is the whole point of boatloader and was furthermore indicated it would do exactly so by xplode earlier on.
Please do take time and hence show consideration to all of us that are trying to help you in preparing yourself properly before trying to attempt any further upgrade.
Good luck!
With regard to your last remark: you stated earlier you did a fresh reinstall of XP. Now, why would you install and connect all these peripherals if you only want to upgrade your BA rom??? All you need is a fresh WinXP and ActiveSync...
Did you really do a fresh install and follow the wiki and the tips mentioned again (and again)?
You are getting me (and probably all of us) confused.
First of all, Sorry if I make you and other confused. I have began to unsuccessfully upgrade my device since Friday. So I decided to help myself at first by try to do everything I can do by myself. I have formatted PC HDD and also reinstalled activesync because I thought the utility may conflict with other program on my PC or from Viruses. I have also tried many ways with hard reset and cold reset etc. to upgrade my device but have no luck. That was with very fresh new installed WinXP PC. Unfortunately, I have to use this computer for my job also. So that's why I have to install printer & scanner driver including MS Office, AutoCAD and other necessary program to serve my job . I have falled with upgrading but I do not want to have problem with my job. Hope you understand my essential.
Your answers to especially points 4 and 5 of xplode tips to me clearly indicate that you do not really take (enough) time to understand the procedures (or what you are doing) and want to have WM6 running asap with no effort at all...
Since I began to upgrading and everytime I have executed the utility I have always wait & wait but I just never look at the clock to see how long I have waited. Xplode has just warned me to take enough time so I started to upgrading but with clock at this time. I have already mentioned that I have successfully upgrade from WM2003SE to the WM6 (previous version) so as a user I have enough experience and know what I am doing.
Your remark "I think the main problem is the activesync has disconnected my device suddenly when started the utility" only confirms this as this is the whole point of boatloader and was furthermore indicated it would do exactly so by xplode earlier on.
This is just my opinion to let you guy see and understand the problem. That's it.
Please do take time and hence show consideration to all of us that are trying to help you in preparing yourself properly before trying to attempt any further upgrade.
I think I have already put a lot of effort about upgradind my device. I have reformatted and reinstalled all necessary programs. It took me out almost half a day to do this. And not only with my PC I have also reinstalled all programs on my device with an old OS version since I have lost them all from hard reset. Other than that I have also tried & tested upgrading the device during the time. The only word I can say that It was not funny to do all of this. It was not really a hard job but it took almost my weekend time.
Good luck!
Yes I do need it barely. Actually I have already felt a little lucky got from all of you that try help me solving the problem. Thanks.
su2003, nice answer.
His main problem is that he does not understand that activSync will work if the device is in a normal state but when device goes to bootlogger mode, its only USB connection that will help a PC to talk to Device and not activSync.
April 1 said:
su2003, nice answer.
His main problem is that he does not understand that activSync will work if the device is in a normal state but when device goes to bootlogger mode, its only USB connection that will help a PC to talk to Device and not activSync.
Click to expand...
Click to collapse
Thanks for your additional.
I have also tried using different PC to upgrade the OS but got the same result.
you have to be sure that your BA when cradled display USB (after getting into bootloader mode) instead of serial 2.06 than run the upgrade utility
I am quite sure that the screen has displayed USB but the number is 2.07 not 2.06. I am not sure about the meaning of the number, it could be the version.
I have also brought a new USB-XDA IIs cable yesterday, just in case the cardle was defected but it doesn't work also, I have got the same result.
khanem said:
you have to be sure that your BA when cradled display USB (after getting into bootloader mode) instead of serial 2.06 than run the upgrade utility
Click to expand...
Click to collapse
I am quite sure that the screen shown USB 2.07 (should be differ version than your).
I have also brought a new USB-XDA IIs sync cable but getting the same result.
Conclusion:
Bad Hardware(Flash ROM)?
Your Bootloader is toasted or had it's LAST flash of it's lifetime???
We can say that... but hopefully not for your sake.
Because as you have said you've done EVERYTHING that was posted.
and though our Senior's "inputs" didnt worked out the way it SHOULD work.
I cant say it's a waste of time to answer your questions.
But there are no more questions to ASK
and there are no more questions to ANSWER
They're all been said here.
All you have to do is PRAY HARD leave the BA rest for a day...
remove the battery...
think things out, clear your mind... sleep...
then execute Xplode's Walkthrough from Step 1 the next day.
but be sure to have the battery fully charged.
Your BA is not dead and your bootloader is not toast. The only problem you have is probably you are impatient. Go to the Wiki and follow the procedure exactly as it is written. It will work. By the way, if you kill Activesync (ie disable USB connection in activesync connection setting), put your device in bootloader mode and connect your usb cable (in that order), run the upgrade and it will work. Forget about activesync.
su2003 said:
I am quite sure that the screen shown USB 2.07 (should be differ version than your).
I have also brought a new USB-XDA IIs sync cable but getting the same result.
Click to expand...
Click to collapse
I use xda IIs and the bootloader mode shows ver 2.07, and i dont have any probs installing. I dont think the version 2.07 has got something to do with your problem.
You said that you tried other pc and it doesnt work, and it worked before when you upgraded previously. I think you know enuf about upgrading if you have done it before....
did you have problem with sync connection before? I was just thinking maybe there is something wrong with your BA....like actual hardware problem with the cable connection??
what about firewall? would it affect it - I doubt it cause its not in sync mode.... but at this stage, maybe just try all possibilities to try to get it working.
Good luck
Mhm. I'm not sure I've really followed all the intricacies of this case ... But whatever, here's my two cents for a safe upgrading procecedure:
1) use a cradle, not a USB cable, and make sure the cradle's
power supply is plugged into a wall outlet. It also helps to make
sure the cradle is plugged directly into the PC, not via any kind of
USB hub. No other devices should be connected to that same USB
channel. I suppose temporarily disconnecting other (unneeded) USB
devices from the computer can't hurt, either.
2) I guess "kill ActiveSync" can mean various things ...
however, here's the best way to do it I think: as sofene mentioned,
disable USB connections (what the hell - disable ALL connections) in
ActiveSync settings. Then reboot the PC. No need to look for ActiveSync
processes and kill them manually -- disabling the connections will take
care of that. Rebooting ensures that ActiveSync's driver code is really
unloaded.
3) remove SD card and, for good measure, SIM card from the BA.
4) perhaps soft (or even hard) reset your device
5) put device in Bootloader mode
6) insert device in cradle, start upgrade utility, off you go ...
By the way, ActiveSync has got nothing to do with the ROM upgrade utility, and it should therefore not have been necessary to re-install ActiveSync, etc. You just have to make sure it does not get in the way of the upgrade process. As far as I understand the process, the ROM upgrade should work equally well on a PC that does not even have ActiveSync installed.
Hi all
I can't connect my Polaris through usb anymore. Nothing happends when I connect the cable. It starts to charge but that's all.
I've flashed my Polaris twice(with 2 different roms from this forum) now since I noticed the problem, using the "micro-sd way" but nothing helps.
"Disable advanced network functionality" didn't work either.
I'm starting to think it's a hardware problem but I can't send it to warranty-repair because I don't have the original rom and I can't flash it back to the original Spl because this can only be done through usb.
But it's still chargering fine when I connect the usb cable so there is some connection still.
Btw., when I put the phone in bootloader mode it says "serial" in the bottom of the screen and it doesn't change to "usb" when I connect the usb cable but my PC pops up a message that says "Usb device not recognized" and under "Device manager" is says "Unknown device". I've tried another cable and another computer but nothing helps.
Any help???
Same happened to me!
I flashed udk r6 rom from SD card after it i could sync from USB normally,
Then i flashed the same rom second time for clean install - again using SD and now i cant sync through USB only through bluetooth...
I thinks its some bug not HW failure maybe uninstall drivers (i use vista btw) and install again?
I've tried uninstalling Activesync and download a new "setup" file and the install activesync again, but this didn't help.
I hope that the problem is software related because if it's hardware related i can't get it repaired through warranty...
Hello, it happend to me to. It just wan`t unlock. It wan`t hard spl. or go into usb mode, only soft reset works. No warrenty, so it will stay in the locker. AS don`t recognaise it. I have the Glass rom, and there where never any problem with it.
Per
It could be a bad contact at the mini-usb connector as it happened to me. Try another cable or push firmly the connector.
maag said:
It could be a bad contact at the mini-usb connector as it happened to me. Try another cable or push firmly the connector.
Click to expand...
Click to collapse
I have already tried another cable and pushing the connector firmly but nothing helps.
I don't understand it because my wall-charger works fine and my headset works fine also. The only thing that doesen't work is acticesync...
exactly the same problem here. after upgrade to r6 and a radio upgrade to murata through PDM activesync no longer works. furthermore the computer doesn't even respond to the phone being plugged in. i had the same response in bootloader mode of not being recognised, but try as i might it will not respond when turned on!
Very frustrating as cannot connect to pc (xp) in anyway.
ICS will not engage as it says "check usb cable connection"
Has anyone moved any further with this issue? i had some issues with the phone being stuck in a bootloader cycle after a radio upgrade but after much angst a Hard reset (and removal of the presumed offending microsd card) solved this!
Read a kaiser thread on possible failure of the microusb connection, specifically the 'B' connectio but elevation of this pin proved fruitless. anyone have any pearls of wisdom on this one?
Try this and it might work...
Start -> settings -> system -> USB to PC
Disable "Enable advanced network functionality".
Hi all.
I just a got a HD2 today. And the first thing that came in my mind was "Let's go to xdaDev to get a nice custom rom". I downloaded one.
After that I put the usb and try to make it syncronize. And the problem is here : ActiveSync dont reconize the phone. I spent the last 4 hours to google why it shall not work. I tried to unstick option at "Start=>Settings=> Usb to PC" but it dont work. Nothing more after perfoming a hard reset and reinstall ActivSync.
But something is strange : When I go in the bootloader, there is the 3 color screen and the phone Display "Serial" at the bottom of the screen ; and when I start it again with USB plugged, it doesnt display "USB" instead of "Serial" it's just void and if I remove the USB "Serial" is displayed.
Plz help me to make the phone syncronize .
I use Windows XP (no firewall, no antivirus) and an official Orange Rom. My SPL is 1.42.0000. I just hope there is no hardware problem ...
Some news ...
The HD2 isnt detected on 2 other PC (Both Win XP). I managed to syncronize my old Diamond too, and it worked well. Same with a HTC Touch and a Touch Cruise, the 3 ones works.
I also tried to use Bluetooth to get an Activesync connection and this time, it noticed the HD2 but no way to get a synchronization.
Any ideas ?
Try this: goto Settings, Other (Miscellaneous settings), USB to PC, Enable faster data data synchronization. Try to tick and untick the last setting.
It doesnt work . I'm trying to follow a "GoldCard" tutorial to flash to an official HTC rom. Maybe it's Orange operator rom ... But if you have any other suggestion, let me know
I can't believe that it's such a s*** to just connect the last HTC phone to a computer. The tutorial need ActiveSync to get the SD card ID so I will not succes in this way.
Is there another software that can be used instead of ActiveSync ?
Did you flash any rom at all or are you still stock?
If you have flashed already, Have you tried to go back to the default shipped rom using sd card (not goldcard)?
Find the rom that shipped with your device, extract the RUU_Signed.nbh file from it, copy it to your fat32 formatted sd card, rename leoimg.nbh, put card in phone, boot phone with down volume held, hopefully you get the message on the three colour screen saying something like 'press volume up to start' or somesuch.
THis should not only flash the rom, but also fix spl if it has become corruptted(which appart from hardware errors is the only reason i can see that it wouldn't recognise a USB connection)
Make sure it is the correct rom for your phone, though, correct vendor and region id.
I must say if you havent flashed yet it sounds like a hardware fault with teh usb cable/connector
I'm currently running a stock Rom from a french operator nammed "Orange". I haven't flashed anything since ActiveSync just dont want to know anything about my HD2.
Maybe I shall send it back to the seller. That's so frustating ...
If i dont find a way to solve this problem until the end of the day, I will return the phone.
Anyway thx for trying to help me
To me either the cable or the phone is faulty. Try another cable if you have one, if not just have the phone exchanged.
Phoque_You said:
I'm currently running a stock Rom from a french operator nammed "Orange". I haven't flashed anything since ActiveSync just dont want to know anything about my HD2.
Maybe I shall send it back to the seller. That's so frustating ...
If i dont find a way to solve this problem until the end of the day, I will return the phone.
Anyway thx for trying to help me
Click to expand...
Click to collapse
Ah in that case then i'd seriously consider taking it back /sending it back. Especially if you have tried more than one computer, sounds to me like faulty cable or USB socket.
kilrah said:
To me either the cable or the phone is faulty. Try another cable if you have one, if not just have the phone exchanged.
Click to expand...
Click to collapse
You must be right. I tried everything and I never had so much pain with my others HTC to get syncronization
I had the same problem not beeing able to connect to the internet via computer. After playing with the activesync settings on the Computer -> conection settings-> ticking on and off some of the boxes->ok, it worked again.
I have connected to three of these phones ( 2 french 1 english) and no problem whatsoever, everything happens without needing to touch any of the settings...is your pc even recognising that something is being plugged in on the USB?
Have you installed the latest version of activesync?
If you have done all the obvious things and it still does not work, the phone or the cable is defective...It should connect straight out of the box with a standard, un changed version of activesync.
Send it back!
Hey, small problem here. I was charging my HD2 earlier today with no problems at all, I flashed the 1.72 stock ROM back onto my phone, and it seemed to be charging fine for a small while after that. But now, after I tried charging my phone, it doesn't seem to recognise there's a USB connection at all. The LED at the speaker-grille isn't doing anything, and the the phone tells me it isn't connected by USB when it's plugged into a computer.
I tried a tonne of things, checked the cable and switched it, soft-reset it, took the battery out, hard reset it, and even blown inside the socket to try and get rid of anything that might be blocking it, but it just isn't showing it's plugged in AT ALL any more... and now the battery is dead, so I can't do anything with it now to try and help it. :/
The only sign I have that the phone realises it has any sort of USB connection, is when I tried to hard reset the device, (I used the hold volUp+volDown+Power method) and it shows the message 'press volUp to hard reset,' usually when I do this, pressing volume up doesn't do anything when the phone is connected by USB for some weird reason - and I have to disconnect USB for the phone to hard reset. I figured this wouldn't happen if the phone doesn't realise it has a USB connection, but when the cable was plugged in, it still wouldn't hard reset until I took it out. So it shows there must be some way the phone knows it's connected.
I'm running the WWE 1.72 ROM with radio 2.10. 50.08_2 if it helps.
Any suggestions?
*Bump*
Sorry for the bump, but it would really help if anyone could help explain this.
I think a bit of trial and error would be best here to establish whats at fault.
phone, cable, or usb port.
-try plugging into a different usb port
-try a different cable (if you have one)
appologies if you have tried these allready.
Tried another cable again just incase, still nothing though. My iPods connected via that USB port I tried using, and that's working fine, so it doesn't seem like that's it, either...
Hi:
I'm having a similar problem. I had plugged in a new retractable usb cable, and when I did, the phone shut off. I rebooted, and tried my original cable, but the phone doesn't charge or sync. I've also tried hard/soft reset, wall charger, usb charger, and none of that seems to work.
Any suggestions?
Thanks.
No idea if this is related or not but my USB connection stopped working after I got the "bttrayce.exe is not a valid pocket pc application" problem (Thanks TomTom! ) so it would appear the USB port has some weird dependencies!
Fixed it by renaming the windows\btsdkce30.dll file (added "[temp]" to the name just in case!) and soft-resetting.
Might be worth a try?
r u using activsync or windows mobile centre ???
USB Issue
I've got exactly the same issue, running HyperROM 3.01.405.T1 and Radio 2.06.51.07.
Suddenly USB isn't working, tried various cables and I suspect it's a software issue somewhere.
Charging isn't a problem at the moment, I have a charging station (ebay from Hong Kong) so I can access the phone and try and resovle this.
I'm going to go back to the stock rom (I assume I'll find that somewhere on XDA) and upddate the Radio version and see if that sorts it.
If anyone has worked out what's casuing this generally let me know as I can imagine this will take a lot of trial and error to solve!
Thanks
have you fixed it?
i am having a similar issue:
I have recently updated my HTC HD2 rom to version 3.14.410.2.
After that i have installed tomtom navigator, but when i turn on the device it returned a message 'BTTRAYCE' is not a valid Pocket PC application'.
I looked at the forums and it was recommended to delete files Windows\BtSdkCE30.dll and
\Windows\BtCoreIf.dll, so i did.
Unfortunately my usb connection is now not working, and i think it could be related to the deletion of those 2 files.
I made a hard reset, but the problem still persists.
can anyone help me please?
My problem solved
Hi i got the same problem , i use ARTEMIS 48 rom 3.14. so my phone suddenly droped to the ground last night but i was charging after that .... next days morning i wanted to connect it to my pc via activesync but it dose not connect .... even disk drive did not work and i could not charge it via AC CHARGER and PC , i toyed around with it here is what i did
1- tried on another pc (result wass the same it did not worked)
2-i hard reseted it (result = the problem was not solved )
3-i went to setting>>>>system>>>power>>>battery and unchecked the option "when phone is on , do not charge ...."
4- i connected it to pc it was not recognozed by pc but it was charging !!!!!!
5-after that i connected it to AC ADAPTOR and it was charging !!!!!!
6- i decided to flash my rom and do a HSPL so my phone will not brick so i connected it to activesync via bluetooth and it was as sucess
7-mean while i was searching this forums
8- i checked my SPL ver
9- i soft-reset and stuning it was recognized by pc and everything was back to normal
in my XP i think it was due to BAD ASS ANDROID ROM and some custom roms bugs....
fpcraveiro said:
have you fixed it?
i am having a similar issue:
I have recently updated my HTC HD2 rom to version 3.14.410.2.
After that i have installed tomtom navigator, but when i turn on the device it returned a message 'BTTRAYCE' is not a valid Pocket PC application'.
I looked at the forums and it was recommended to delete files Windows\BtSdkCE30.dll and
\Windows\BtCoreIf.dll, so i did.
Unfortunately my usb connection is now not working, and i think it could be related to the deletion of those 2 files.
I made a hard reset, but the problem still persists.
can anyone help me please?
Click to expand...
Click to collapse
Uninstall TomTom and the problem goes away.
You can download versions on TomTom Navigator 7 with the Bluetooth files removed - like * HERE *
I don't have an OS installed...
This is due to aMAGLDR being installed and when I had the device open.. I created a 'temp' folder and my next task was to create a 'create_to_sd_root', well I renamed the temp folder to that... bad move? I think so. My system acknowledges the device, however I'm unable to access it. I.e. my computer(no icon), windows mobile center(not connected), etc. Please help! I need my phone!
MrHellas said:
This is due to aMAGLDR being installed and when I had the device open.. I created a 'temp' folder and my next task was to create a 'create_to_sd_root', well I renamed the temp folder to that... bad move? I think so. My system acknowledges the device, however I'm unable to access it. I.e. my computer(no icon), windows mobile center(not connected), etc. Please help! I need my phone!
Click to expand...
Click to collapse
I you were trying to flash Android you just need to flash Clock Work Mod (CWM) and then place the .zip file for the Android ROM on your SD card and use CWM to flash the Android ROM. It is links to Youtube videos in the OP of the thread showing you how to flash CWM and the ROM.
Are you could flash back to Win MO through USB and bootloader or SD card and bootloaderr.. If you go for USB and bootloader make sure you see USB in the white bar of bootloader befor tryng to flash the ROM. Also thew SD card metrhod will remove HSPL if you use a Official and not a custom ROM.
Well I've figured out how to get the android os on there, however I'm unable to locate the drivers for AD8? I'm still unsure about what folder/files need to be on my microSD if I'm running the Desire HD Froyo(current) I cannot access any internal/external(microSD). Help?
MrHellas said:
Well I've figured out how to get the android os on there, however I'm unable to locate the drivers for AD8? I'm still unsure about what folder/files need to be on my microSD if I'm running the Desire HD Froyo(current) I cannot access any internal/external(microSD). Help?
Click to expand...
Click to collapse
You have to use MAGLDR's mass storage option to get access to your SD card, or use the mount storage option in Clock Work Mod. I recomemd usingvthecnass storagecin MAGLDR though as I have had trouble gettingvthecdrivers for mount storage in CWM to install but have never had a problem with the mass storage option in MAGLDR.
T-Macgnolia said:
You have to use MAGLDR's mass storage option to get access to your SD card, or use the mount storage option in Clock Work Mod. I recomemd usingvthecnass storagecin MAGLDR though as I have had trouble gettingvthecdrivers for mount storage in CWM to install but have never had a problem with the mass storage option in MAGLDR.
Click to expand...
Click to collapse
How do I get back the loader without booting up? Obviously haven't been able to copy the rar files. Could this be why my GPS and other functions could not be working properly?
imanh said:
3-i went to setting>>>>system>>>power>>>battery and unchecked the option "when phone is on , do not charge ...."
Click to expand...
Click to collapse
Thanks this sorted my problem!
imanh said:
Hi i got the same problem , i use ARTEMIS 48 rom 3.14. so my phone suddenly droped to the ground last night but i was charging after that .... next days morning i wanted to connect it to my pc via activesync but it dose not connect .... even disk drive did not work and i could not charge it via AC CHARGER and PC , i toyed around with it here is what i did
1- tried on another pc (result wass the same it did not worked)
2-i hard reseted it (result = the problem was not solved )
3-i went to setting>>>>system>>>power>>>battery and unchecked the option "when phone is on , do not charge ...."
4- i connected it to pc it was not recognozed by pc but it was charging !!!!!!
5-after that i connected it to AC ADAPTOR and it was charging !!!!!!
6- i decided to flash my rom and do a HSPL so my phone will not brick so i connected it to activesync via bluetooth and it was as sucess
7-mean while i was searching this forums
8- i checked my SPL ver
9- i soft-reset and stuning it was recognized by pc and everything was back to normal
in my XP i think it was due to BAD ASS ANDROID ROM and some custom roms bugs....
Click to expand...
Click to collapse
I did the same but no work. I have issue #USB not recognized# after installed Android Transformer SD ver.
In three color screen I have USB connection working fine. I could install HSPL4, update Radio, but Win 6.5 has a USB problem.
I don't think this is a hardware issue or I am wrong?
Still confused. Should I take my phone to service?
Hi,
I have the similar problem with my hd2, but worse. Out of 3 different comouters I tried none can see the phone connected and gives me the error saying one of the USB device connected to this computer has malfunctioned and cannot be recognized. I have tried two different cables. I cannot connect my phone through latest magldr using USB flasher or USB mass storage modes. Moreover, when I connect my phone in rainbow screen (hspl screen where you install magldr), it should change to USB from serial but even that does not happen. ANy solutions?? I think its my phone.... Is there any way to revert this back to normal. I don't want a brick.
mcdoc said:
I did the same but no work. I have issue #USB not recognized# after installed Android Transformer SD ver.
In three color screen I have USB connection working fine. I could install HSPL4, update Radio, but Win 6.5 has a USB problem.
I don't think this is a hardware issue or I am wrong?
Still confused. Should I take my phone to service?
Click to expand...
Click to collapse
Your USB drivers for the defualt bootloader (multicolor screen) seem to be working fine, so no you do not have a hardware problem. You might want to uninstall Windows Mobile Device Center or Active Sync, which ever one your computer uses. Then re install it. Also go to device manager in your comtrol panel while you have hour HD2 booted up and connected via USB and clck on update drivers for hour phone, it should be listed in device manager.
kushki said:
Hi,
I have the similar problem with my hd2, but worse. Out of 3 different comouters I tried none can see the phone connected and gives me the error saying one of the USB device connected to this computer has malfunctioned and cannot be recognized. I have tried two different cables. I cannot connect my phone through latest magldr using USB flasher or USB mass storage modes. Moreover, when I connect my phone in rainbow screen (hspl screen where you install magldr), it should change to USB from serial but even that does not happen. ANy solutions?? I think its my phone.... Is there any way to revert this back to normal. I don't want a brick.
Click to expand...
Click to collapse
When you say your Serial in boorloader does not change to USB this tells me you are having driver issues or hardware issues with your micro USB port on your HD2. My bet is it is just driver issues. I sugest you uninstall and rei nstall Wimdows Mobile Device Center or Active Sync which ever one your computer uses. These programs contain the USB drivers for the HD2 and MAGLDR partialy relies on those drivers to. So maybe that will solve your problem.