HTC Tytn (Herm200) Stuck at Windows mobile/HTC startup screen. - 8525, TyTN, MDA Vario II, JasJam General

One fine day it refused to startup. No matter how many resets i do it always hangs up at the startup screen. "windows mobile" written on the top and HTC at the bottom. Tried soft resetting, hard resetting, nothing works. Am able to get into the bootloader mode though(by pressing ok button and power button then hitting reset, no clue what that mode is for.)
I have no clue what to do ? how to get it to work again. Could some one help please??

is this on a 6.1 rom?
if so
Get into bootloader mode (side ok and power buttons and reset)
Test for bad blocks via mtty and fix if need be.
Flash carrier rom (AT&T official rom reccomended)
Reflash 6.1 rom
however if it is just from official rom go to bootloader mode install hardspl and reflash your current rom

Related

mda vario

I have a big problem with my mda vario.
the begenning: !. i done a hardreset and before finishing a softreset.
now my ppc doesnt boot anymore. the hung up is by the screen of t-mobile.
Plese help me!
What can i do now, is my mda vario over?
No resets bring me forward
Touchscreen or any other buttons doesnt react and doesnt work anymore.
The only thing that i can do is to remove the battery
Stupid question, but why would you do a soft reset in the middle of a hard reset?
Anyway, probably your best bet would be to download the latest t-mobile rom, put your phone in bootloader mode and flash the rom again. This time, avoid doing a soft reset in the middle of it.
how do i install the rom in the ppc if it doesnt boot.
can you give me a todo list, please ?
how can i put my phone in bootloader mode
Press and hold the camera key and then press the on button. When multicolored bootloader screen comes up release the camera button and then you're ready to flash.

Help help please stuck on bootloader

Help Help Help
Iam new to the flashing
I have herald (HTC P430 HERA) with wm5 ,i tried to upgrade to wm6 with TOUCH-IT.I installed the SPL and then ran the RUU ,everything was perfect the installation started normally ,durin the installation i chose the option to use the keylock ,when my htc started it kept on asking me the password on the device which i entered but it did not accepted .i kept on trying and eventually took out the battery.When i restarted the device it got stuck on a green scnreen with spl 1.08.0001 and when turned off i tried going in to the bootloader but everytime i run the same ruu it gives me erorr 300 i have tried several times now, donwloaded each and every ruu but all in vain and im in pain .sometime the screen get stuck on 0% . Can somebody help or atleast direct me to the right area.
at least it we could reach 1% rom update can be done
i think we can handle it via bootloader commands
you need to install enablerapi....
.......................
You have to download the official Tmobile RUU (google it), and reinstall it. After that before you try to flash your phone you have to take the Enablerapi cab and put it on your phone. After that do a hard reset. If you dont know what that is by now you shouldnt be flashing your phone. But anyway hold the buttons above the talk and end buttons and press the reset button at the same time. A black screen will come up and ask you to press the talk button (green button), press it and the phone will do a reset. Configure your screen and connect phone to active sync/WMDC and make sure you put the phone in airplane mode. Then run the uspl again and follow the directions on the screen.

Plz help me..! all Rom update failed at 2%

dear all experts ...
I tried to update my Shadow by the new wm6.1 rom.. the first time it went to 100% and restart with an error 270 : the image is corrupt . After, when I boot loader, it go to 2% and restart every time ( many) :
I'm stucked at bootloader mode and tried many roms but no one sucsess ... all of them reach 2% and then stopped.
even I tried the original one (Shadow_Software_Update_1.11.531.5.exe) from t-mobile official site but also same result.
so can any one help me and give me any solution to try?
try to install this on your phone
http://forum.xda-developers.com/showthread.php?t=394478
after that try installing a cooked ROM
Dear sir;
thanks a lot for attention to my problem and ur kind reply.
I already tried to do this but...
* How can I upload sspl/uspl to my phone from bootloader because it's the only mode I can work my phone?
* when I tried to do USPL + RUU it go to 100% and then the phone restart and the RUU program says corrupted image...
then the phone stays in it's state (only can go to bootloader mode).
can I use MTTY program to flash sspl/uspl and USPL and then the new rom? if yes .. how I can do it?
Or what may I do my friend..
thnx a lot again
if you can only get to the bootloader then try flashing to the t mobile rom, then start over
Mee toooooo
I installed this ROM and it doesn't work!!
the screen is freeze with the Windows 6.5 Logo, and thats it!!!!
what can i do for do a hard reset?????? (i already do that thing, power it on, and then push the 2 soft buttons, and didn't work!),
HEEEEEEEEEEEEEELP!!!!
isfected said:
I installed this ROM and it doesn't work!!
the screen is freeze with the Windows 6.5 Logo, and thats it!!!!
what can i do for do a hard reset?????? (i already do that thing, power it on, and then push the 2 soft buttons, and didn't work!),
HEEEEEEEEEEEEEELP!!!!
Click to expand...
Click to collapse
Power off the phone
Press and hold the camera and voice keys
Insert the USB cable, Keep holding the camera and voice keys until you get the bootloader screen
Then flash an original ROM.

Flashing ROM with Android....

So, I've been using an Android ROM I found on the net on my vogue for some time now, but now I want to try out some other ROMs. However, the RUU requires a connection to ActiveSync, which isn't posible from Android. Anybody know how to do this?
All you have to do is hold the power button and take the pen and soft reset at the same time the phone should go into the hard SPL mode.. From there start up the romupdate you should be good to go
I tried that already, all it does is reboot my phone. No hard SPL mode
Hold the power and the camera buttons and reset to put it in bootloader mode
Ah yes that worked, thanks a lot .

HD2 Frozen... asking the right questions

Just loaded another keyboard cab and suddenly on soft reset/reboot the phone has frozen at the HTC logo and the screen showing the RGD info... won't reboot easily and takes many attempts to get back to this screen.. but will go no further.
So to do a search, what keywords should I be using or does anyone recognise this and have an answer.. have tried reset, battery out but nothing is working, the screen is just locked the screen mention above.
Using Laurentius26 GoldEdition V2.1 rom and was loading Touch-Keypad.Cab..
It is not connecting to the pc, so I can't reflash it at this time..
if you're phone wont boot since you installed this then looks like a hard reset is on the way mate sorry, you could try boot without mem card but doubt that will make a difference
Could you quickly remind me of the sequence for hard reset, red reset button doesn't seem to do a lot and I do have everything backed up so its not a problem... cheers.
press and hold both volume buttons and tap the power button. Keeping holding both volume buttons until it asks you if you want to factory reset the device. When it does tap volume up and it will then go off and do it's thing.
if the crash was the first time you had soft reset since youi installed the cooked rom, (even if you had been using it a while) it could be a mismatched radio. (Sometimes the rom/radio mismatch doesnt show till the first restart.)
Look at the R on the boot screen, if it has .51. in the version, then flash a new radio.
Thanks for all the help.. have managed to recover, restart and reflash, then reload, so we are all sweet now.. cheers..

Categories

Resources