Related
I have a Cingular 8525 running WM5 that is stuck in bootloader screen. I have tried to soft and hard reset ... just boots back to the same screen, I can't turn it off once in the screen and when i sync via usb to the pc i get the message that the "usb device that is connected is malfunctioning" I have not done any upgrading at all and the phone worked perfectly right up till the time i powered it down and restarted into the bootloader screen.
Please can someone out there help me with this issue?
Zulu137 said:
I have a Cingular 8525 running WM5 that is stuck in bootloader screen. I have tried to soft and hard reset ... just boots back to the same screen, I can't turn it off once in the screen and when i sync via usb to the pc i get the message that the "usb device that is connected is malfunctioning" I have not done any upgrading at all and the phone worked perfectly right up till the time i powered it down and restarted into the bootloader screen.
Please can someone out there help me with this issue?
Click to expand...
Click to collapse
same problems, run perfect before with schaps wm6 rom then flash to faria wm6.1... not feel good with faria. try to flash with other rom then the problem start ..
how to recover ....... please help
Asfarizal said:
same problems, run perfect before with schaps wm6 rom then flash to faria wm6.1... not feel good with faria. try to flash with other rom then the problem start ..
how to recover ....... please help
Click to expand...
Click to collapse
Manage to solve the problem ...thanks WIKI !!
Go to Bootloader mode: Hold side OK and POWER buttons together and reset with stylus
Then Flash to any ROM you want !!
Thanks .... But
Thanks for the reply ... but i have no idea how to do what you tell me, I am new to all this phone "stuff" as a matter of fact this is the first time that i am ever using one of these forums. I have read till i am cross eyed but dont actually understand what you are talking about ... now don't let that scare you away as i am willing to learn and i am not braindead ... you all had to start sometime in this, not so. I get that i need to try and reflash my rom...
so is there some type of rom update software that i need? ... what is a hard SPL?? ... and who is Schaps?? .. sorry guys to do this to you but i would like to get into this game and i need some ( well maybe a lot ) of pointers.
Thanks for your time.
1. Search for "mr vanxs guide" so you have an idea on what you're doing.
2. OK, as Asfarizal said "Go to Bootloader mode: Hold side OK and POWER buttons together and reset with stylus". If you cant work out what the buttons are, go to the manual. it will tell you.
3. type in "hard SPL" in search on the forum & download the .zip or .rar file. this should have 2 files inside when opened,
a). RUUWrapper.exe and
b). RUU_signed.nbh
sync Hermes and double click .exe file. follow prompts.
4. find a rom that you want (would suggest TNT SE as a fairly good rom for noobs... good and stable, no problems...) Again download, then (and this is personel preference) format an sd card fat 32 and copy RUU_signed.nbh into root directory. Rename it Hermimg.nbh. Put into Phone and put into bootloader(make sure the battery is more than 50%) follow prompts. This should get you out of trouble. You can also sync your Phone and double click on the RUUWrapper.exe HOWEVER, if you should reset your computer, pull out the usb cable or have anything else happen to the computer that interrupts the flashm, you could end up with a worse brick than you have now. try to read up on flashing (search for "mr vanxs guide") and this should help you a lot if you have other questions. Good luck and happy flashing......
Thank You
I will follow the instructions you gave and try to get it going this weekend.
Thank you so much for your time
Zulu137 said:
Thanks for the reply ... but i have no idea how to do what you tell me, I am new to all this phone "stuff" as a matter of fact this is the first time that i am ever using one of these forums. I have read till i am cross eyed but dont actually understand what you are talking about ... now don't let that scare you away as i am willing to learn and i am not braindead ... you all had to start sometime in this, not so. I get that i need to try and reflash my rom...
so is there some type of rom update software that i need? ... what is a hard SPL?? ... and who is Schaps?? .. sorry guys to do this to you but i would like to get into this game and i need some ( well maybe a lot ) of pointers.
Thanks for your time.
Click to expand...
Click to collapse
Looks like you've got a lot of reading to do, and a problem to sort out. Firstly a couple of answers...
Schaps is a Rom Cooking guru (makes custom versions of WM5, WM6 etc). When you get your phone sorted out I'd recommend trying one of his roms.
Hard SPL. The SPL is part of the bootloader which effectively dictates how a rom is flashed and what roms can be flashed. HardSPL is a custom version of this which allows you to flash any rom from any carrier. It also protects against a bad flash in many cases. It is recommended before you try flashing any new roms or radio roms. Use Hard-SPL-V7 at the bottom of the first post here.
The Rom upgrading software is contained in any of the cooked or carrier supplied roms. It is normally a .zip file which cotains 2 files: xxxxxRUU.exe and RUU_signed.nbh. You run the .exe file from your PC when connected to your phone via USB. More details of how to do this are in MrVanx's guides. Also other resources here.
Now to try to sort your phone out...
What is displayed on your screen when in bootloader mode? It should be something like this:
HERM200
IPL-1.04
HERM200
SPL-2.10.Olipro (This is HardSPL V7)
If you don't have an Olipro SPL then you need to get HardSPL onto your phone. If you haven't done any upgrading and have had the phone from new then I guess you don't have hardSPL.
Now you need to fix your USB Malfunctioning problem. I can't help too much here except to suggest trying a different cable, different USB port or different PC. Also, if you are running Vista try an XP maxhine. When you connect to the PC does your phone show Serial or USB on the screen? If you can't get a USB connection, all is not lost - you can re-flash your rom using an SD card, method here.
There is a thread about un-bricking phones which may help.
There are various diagnostic tools (which can also screw your phone if used incorrectly). The favourite of these is MTTY but you need a USB connection to use this.
If your phone is in warranty I'd recommend getting your supplier to sort it out, but if not I'd try to re-flash an ORIGINAL supplier rom (Cingular I guess). You can get links to the official supplier roms here.
I think (might be wrong) that sometimes when stuck in bootloader you need to flash an official rom, not a cooked one to recover your phone - then you can run HardSPL and then flash cooked roms again.
Cingular 8525 stuck in bootloader
Thanks for the reply ... lots of great input.
Now to answer some of your questions.
1) When I power up the phone (only pushing the power button ) it goes straight into the bootloader screen without pushing any other buttons, and it displays
HERM100
IPL-1.01
HERM100
SPL-1.06
Then at the bottom in the white bar it says "Serial"
The only way that i have found to power it down again is to remove the battery, there is no response from any single buttons after it is in bootloader
the soft reset and hard reset work but it just goes right back to the bootloader screen after.
2) The USB malfunction. This only started after the phone "crashed" and before that it worked great ... well i only used it to sync up to my work pc for the contacts and to get pictures onto my hard drive.
all the PC's that i use are running XP. I have tried my home PC and my Laptop
and the work PC and all of them have their own cables and they all say the same thing ... "the USB device is malfunctioning"
I am sure that when i get the phone going again the USB will start to function again.
3) Phone warranty ... I bought the phone off e-bay from a store in new york about 10 months ago as a "new unlocked cingular 8525" it was new and unlocked, but i have no idea how they unlocked it. I would assume that there would be no warranty now and in any case i live in Canada and would have to ship it down to the states to an AT&T repair center and that sounds like a nightmare to me with the customs and so on.
I will give you a little more background on the problem. the phone worked like a charm without any problems at all for the 10 months that i had it, then the morning of the crash the phones alarm did not go off in the morning and i was almost late for work ... i did not pay it any further attention untill at 3:26pm
that afternoon the alarm went off ??????? (it was set for 6:05am) so i checked the main clock time, it was right. I then checked the alarm time, it was right ??? So i figured that something must have just got confused, so i powered down the phone with the power button to just restart it and while it was powered down i removed the battery to take the oportunity to to clean all those fuzzies and dust that collect in the battery compartment out and put it all together and powered it up again (just by pushing the power button) and this wierd red, green, blue and white screen appeared and that is all that i have seen since ???
I hope that answers your questions and i will start going through the links that you sent and get to reading ... will there be a pop quiz ... lol
Thanks again for your time and i very much appreciate all the time that all of you have spent on me and my phone ..... I know that you all just feel bad for me because i now have to use a Motorolla V551 ... lol
Great Work
ultramag69 said:
1. Search for "mr vanxs guide" so you have an idea on what you're doing.
2. OK, as Asfarizal said "Go to Bootloader mode: Hold side OK and POWER buttons together and reset with stylus". If you cant work out what the buttons are, go to the manual. it will tell you.
3. type in "hard SPL" in search on the forum & download the .zip or .rar file. this should have 2 files inside when opened,
a). RUUWrapper.exe and
b). RUU_signed.nbh
sync Hermes and double click .exe file. follow prompts.
4. find a rom that you want (would suggest TNT SE as a fairly good rom for noobs... good and stable, no problems...) Again download, then (and this is personel preference) format an sd card fat 32 and copy RUU_signed.nbh into root directory. Rename it Hermimg.nbh. Put into Phone and put into bootloader(make sure the battery is more than 50%) follow prompts. This should get you out of trouble. You can also sync your Phone and double click on the RUUWrapper.exe HOWEVER, if you should reset your computer, pull out the usb cable or have anything else happen to the computer that interrupts the flashm, you could end up with a worse brick than you have now. try to read up on flashing (search for "mr vanxs guide") and this should help you a lot if you have other questions. Good luck and happy flashing......
Click to expand...
Click to collapse
Thanks a lot man & great work i unbricked my Herm100 with method u mention above thanks a lot & great job keep it up
I also have this problem.
I d/l Hard-SPL-V7
and when i run RUUWrapper.exe
I get an error saying the application failed to initialize properly (0xc0000135)
What's going on?
How do i fix this?
this happened when i was trying to unlock the phone.
Thanks
need help
when i switch on my orange herm100 it shows On the bootloader screen is displayed:
HERM100
I PL-1.01
HERM100
SPL-1.40.01ipro
history : i buy unlocked orange phone
fewdays back i found no imei ,
yesterday i try to flash by micro sd but in gsm stage its gets hang no progress after extrom stage
IPL - OK
BOOTLOADER - OK
SPLASH1 - OK
SPLASH2 - OK
EXTROM - OK
GSM - (NO ACTION)
OS -
i tryed several time no action, i cant connect by mini usb.
PLEASE help me
tell me which it the right rom to chose? step by step procedure..
how to rectify imei?
thanks and regards
kirtibas
kirtibas, sorry it took so long to reply, 1st thing I'd do is upgrade to SPL 2.10 olipro. This is safer to use than others. then I'd suggest reflashing a stock rom to see if that works. After stock rom works then use a cooked rom as your heart desires... Cheers...
Ah i'm just trying to update the radio.
Can someone tell me how to do it? The wiki is just confuzing me more.
The wiki and threads I've read just confuse me more.
Is this what ur sposed to do:??
1. GET customRUU.exe
2. put HD_Blackstone_Radio_1.10.25.25.nbh in customRUU directory.
3. load and follow instructions
4. get bar that doesn't get past 0%
5. get ERROR [262]: Update error, communication errors.
by the way i think I have an unmodified standard rom.
AvocadoBaby said:
by the way i think I have an unmodified standard rom.
Click to expand...
Click to collapse
i am assuming you have hardspl?? also is the phone synced to pc before starting upgrade?
thesire said:
i am assuming you have hardspl?? also is the phone synced to pc before starting upgrade?
Click to expand...
Click to collapse
Copy the .nbh into the root of your storage. Enter bootloader mode by turning phone off, then press vol down and hold down while quickly pressing the power button. Keep holding the vol down key until you see the tricolour screen. It will then find your .nbh file on storage card and ask if you want to install. Once finished, soft reset and away you go.
Make sure you have Hard SPL.
As others have said, you need hard spl, I have vista 64 and the updater works perfectly.
im getting a touch hd from taiwan. and i just read that it comes in chinese only
is there any rom to make it english? or change the os language to english
and what is the country code for it?
if there isnt. will i have to use hard spl?
and i read the instructions for it but im kinda lost
please help
Thanks in advance
Allmost all ROMS are in english. There are ways you can flash them without using hard spl.
EpiphanyNL said:
Allmost all ROMS are in english. There are ways you can flash them without using hard spl.
Click to expand...
Click to collapse
i checked "http://wiki.xda-developers.com/index.php?pagename=HTC_Blackstone_Ship_exe"
and im not sure which one to download
im not really sure which is the country code for taiwan. any ideas?
there are ways to flash without using hard spl?
can you please tell me how?
Read this for flashing without Hard spl: http://forum.xda-developers.com/showthread.php?t=462347
Why would you want the country code for taiwan? You dont need it when flashing another ROM.
EpiphanyNL said:
Read this for flashing without Hard spl: http://forum.xda-developers.com/showthread.php?t=462347
Why would you want the country code for taiwan? You dont need it when flashing another ROM.
Click to expand...
Click to collapse
i read that i need to know so i know which rom to download?
i think. i read it here " http://wiki.xda-developers.com/index.php?pagename=HTC_Blackstone_Flash1"
so im going crazy looking for a rom that i could use.
do you know where i can download one so i can make my language WWE instead of chinese.?
I'm using this ROM atm: http://www.laurentius26.net/
You can find enough ROMS in this thread btw, read carefully and you will find them
EpiphanyNL said:
I'm using this ROM atm: http://www.laurentius26.net/
You can find enough ROMS in this thread btw, read carefully and you will find them
Click to expand...
Click to collapse
thanks but one question?
which is the easiest way to flash a rom?
using Hard SPL, Soft SPL, or USPL?
im really lost on that..
and which one should i use?
Cant really help you there, I use hard SPL, but I guess it's just what your preference is in that.
EpiphanyNL said:
Cant really help you there, I use hard SPL, but I guess it's just what your preference is in that.
Click to expand...
Click to collapse
oh really?
hardspl is only for blac100 right?
but i read that now they have like blac120?
and im not sure which one im gunna be getting in the box.
oh. when i change the os language. do i have to download one with the same country code?
i read in another place that if you dont have the same. then. it wont work?
or with hardspl and uspl i dont need to have the same country code
anyone? im kind of a newbie
i need help please
im going to be getting my touch hd soon in chinese
and i need to change it to english
help
thank you!
kevin6192 said:
anyone? im kind of a newbie
i need help please
im going to be getting my touch hd soon in chinese
and i need to change it to english
help
thank you!
Click to expand...
Click to collapse
Its not very hard to be honest
You must flash HardSPL first to be able to flash any rom and hardspl will work for blac100 and blac120
More info and instruction about HardSPL
Tips about flashing the rom
Use fully charged device
* Switch off your device by holding the Power button untill a menu pops up
* Go to bootloader by holding Volume down + Power button at the same time
* Connect your device to your PC
* Start BlackStoneCustomRUU.exe and follow the onscreen instruction's
There are countless ROM's out there and everyone has different tastes so there is no point asking any questions on which is better etc etc etc.
I am curretnly using Duttys 2.3 rom and would recommned it or Laurentius26 V9.0
Hope this helps!
Laurentius26
I got mine from hong Kong when I was there in Feb, it was in chinese too. then I went to the wiki page, downloaded the Hard SPL, once that was done I just picked any ROM on the wiki page, I chose Dutty 1.7 at the time. copied the NBH file to the root of the SD card, made sure the name of the NBH file was BLACIMG.nbh and then used restarted the device with the key presses mentioned in the wiki and flashed it to english. MAKE sure you have at least 50% charge before you start.
the WWE versions are the english roms. I believe its mentioned in the wiki too.
Since then I've maybe flashed like 10 or more times and tried different roms. it doesn't matter which rom you pick. its a matter of personal preference. just take the time to read the wiki in detail and you'll be fine.
if you are getting a retail touch HD it will come with an 8GB SDHC micro SD and the usual accessories.
as of now I'm on dutty's 2.3
alvinswim said:
I got mine from hong Kong when I was there in Feb, it was in chinese too. then I went to the wiki page, downloaded the Hard SPL, once that was done I just picked any ROM on the wiki page, I chose Dutty 1.7 at the time. copied the NBH file to the root of the SD card, made sure the name of the NBH file was BLACIMG.nbh and then used restarted the device with the key presses mentioned in the wiki and flashed it to english. MAKE sure you have at least 50% charge before you start.
the WWE versions are the english roms. I believe its mentioned in the wiki too.
Since then I've maybe flashed like 10 or more times and tried different roms. it doesn't matter which rom you pick. its a matter of personal preference. just take the time to read the wiki in detail and you'll be fine.
if you are getting a retail touch HD it will come with an 8GB SDHC micro SD and the usual accessories.
as of now I'm on dutty's 2.3
Click to expand...
Click to collapse
Fallen Spartan said:
Its not very hard to be honest
You must flash HardSPL first to be able to flash any rom and hardspl will work for blac100 and blac120
More info and instruction about HardSPL
Tips about flashing the rom
Use fully charged device
* Switch off your device by holding the Power button untill a menu pops up
* Go to bootloader by holding Volume down + Power button at the same time
* Connect your device to your PC
* Start BlackStoneCustomRUU.exe and follow the onscreen instruction's
There are countless ROM's out there and everyone has different tastes so there is no point asking any questions on which is better etc etc etc.
I am curretnly using Duttys 2.3 rom and would recommned it or Laurentius26 V9.0
Hope this helps!
Laurentius26
Click to expand...
Click to collapse
im sorta confused on how to install Hardspl
i read the instructions..but im lost
do you think you guys can help me out?
like explain in an easier way?
sorry for the inconvenience
can i also use USPL?
kevin6192 said:
im sorta confused on how to install Hardspl
i read the instructions..but im lost
do you think you guys can help me out?
like explain in an easier way?
sorry for the inconvenience
can i also use USPL?
Click to expand...
Click to collapse
Instructions
Download Hard-SPL package from attachment, extract to an empty folder.
Unsigned_HardSPL_for_Blackstone_OliNex.zip
You must Have Phone Sync'd with PC in Windows Mobile!!!
Run HardSPLWrapper_Blackstone.exe on PC,
make sure it's launched from a local drive (not through network drive, etc.).
if you are on vista, launching as Administrator is recommended,
Follow steps in the RUU
check device for prompts after PC shows loading bar
press Yes on phone if asked.
Some notes: When RUU says it will hard reset, do not worry, it is not going to do that. also when it says the flash will take 10 minutes, ignore that, it will only take a minute or so.
Device should go to a tricolour screen now that says 1.07.OliNex, the SSPL version, which is temporary.
In a bit unusual way, it will take a few seconds for the RUU to detect the device, but do not worry, as soon as the "USB" text on the tricolour screen shows up, RUU will see device.
SPL flashes, device automatically reboots, job done.
To confirm you got it installed,
go into bootloader mode (tricolour screen!) (Switch off your device by holding the Power button untill a menu pops up > Go to bootloader by holding Volume down + Power button at the same time)
verify the screen shows 1.14.OliNex, which is the Hard-SPL version.
I just got my Touch HD over the weekend and I used USPL so that I don't void the warranty:
http://forum.xda-developers.com/showthread.php?t=462347
However, you need to have XP. Tried it on Vista but not successful. Luckily I had an old XP laptop stuffed away somewhere
ionrage said:
I just got my Touch HD over the weekend and I used USPL so that I don't void the warranty:
http://forum.xda-developers.com/showthread.php?t=462347
However, you need to have XP. Tried it on Vista but not successful. Luckily I had an old XP laptop stuffed away somewhere
Click to expand...
Click to collapse
oh really?
when it says
"Execute blac_uspl.exe;" do i just find the file ont he computer and double click it? or do i have to like install it using the phone?
and " If everything goes well, your device will restart and SPL version label should read "1.14.USPL" indicating that USPL was loaded successfully."
once that is done then... am i done?
this next part is when i want to flash a rom right?
("You can then start RUU update to flash RUU_signed.nbh. Once RUU update is completed, device will restart using regular flashed SPL.
If you want to flash from SD card instead, make sure your SD card is not inserted when you enter the bootloader originally.
SPL will try to install it and would fail if blacimg.nbh is not signed by HTC. Insert the card after "USB" label comes up in SPL but before running USPL.
You can run "blac_uspl.exe ?" to get command line parameter help. Only 1 parameter is accepted and that is the name of an SPL file you want to load. You can load an MFG SPL or HSPL. USPL automatically takes care of allowing unsigned/cooked ROM flashing with any SPL you use.")
man. i dont have XP
thers no way on vista?
thanks for the inconvenience.
Fallen Spartan said:
Instructions
Download Hard-SPL package from attachment, extract to an empty folder.
Unsigned_HardSPL_for_Blackstone_OliNex.zip
You must Have Phone Sync'd with PC in Windows Mobile!!!
Run HardSPLWrapper_Blackstone.exe on PC,
make sure it's launched from a local drive (not through network drive, etc.).
if you are on vista, launching as Administrator is recommended,
Follow steps in the RUU
check device for prompts after PC shows loading bar
press Yes on phone if asked.
Some notes: When RUU says it will hard reset, do not worry, it is not going to do that. also when it says the flash will take 10 minutes, ignore that, it will only take a minute or so.
Device should go to a tricolour screen now that says 1.07.OliNex, the SSPL version, which is temporary.
In a bit unusual way, it will take a few seconds for the RUU to detect the device, but do not worry, as soon as the "USB" text on the tricolour screen shows up, RUU will see device.
SPL flashes, device automatically reboots, job done.
To confirm you got it installed,
go into bootloader mode (tricolour screen!) (Switch off your device by holding the Power button untill a menu pops up > Go to bootloader by holding Volume down + Power button at the same time)
verify the screen shows 1.14.OliNex, which is the Hard-SPL version.
Click to expand...
Click to collapse
do i have to have the phone connected to the computer before i run HardSPLWrapper_Blackstone.exe?
what does it mean when it says make sure it is launched from a local drive?
or a network drive?
where are the steps for the RUU?
sorry for all the questions!
kevin6192 said:
do i have to have the phone connected to the computer before i run HardSPLWrapper_Blackstone.exe?
what does it mean when it says make sure it is launched from a local drive?
or a network drive?
where are the steps for the RUU?
sorry for all the questions!
Click to expand...
Click to collapse
Yes, you need phone sync'd to pc using your usb cable before running HardSPLWrapper_Blackstone.exe?
What I mean by local drive is your C:/ drive or local disk and not by using other drives you may have i.e. G:/, H:/, J:/ etc
When you run HardSPLWrapper_Blackstone.exe a screen will appear on your pc and it will have these steps on it for you to follow. i.e. just follow these steps
Fallen Spartan said:
Yes, you need phone sync'd to pc using your usb cable before running HardSPLWrapper_Blackstone.exe?
What I mean by local drive is your C:/ drive or local disk and not by using other drives you may have i.e. G:/, H:/, J:/ etc
When you run HardSPLWrapper_Blackstone.exe a screen will appear on your pc and it will have these steps on it for you to follow. i.e. just follow these steps
Click to expand...
Click to collapse
okay so i have downloaded HardSPLWrapper_Blackstone.exe.
it says extract it so that means i cannot open it from the zip?
is it okay if it is in a folder in the C:/ drive when i launch it?
so first off. i connect the phone to the pc.
( do i put it in bootloader mode?)
what will show on the phone when i connect it?
and when i connect it. i just plug the usb in the phone and the computer and thats it?
then i launch HardSPLWrapper_Blackstone.exe
follow the steps..
then im done?
kevin6192 said:
okay so i have downloaded HardSPLWrapper_Blackstone.exe.
it says extract it so that means i cannot open it from the zip?
is it okay if it is in a folder in the C:/ drive when i launch it?
so first off. i connect the phone to the pc.
( do i put it in bootloader mode?)
what will show on the phone when i connect it?
and when i connect it. i just plug the usb in the phone and the computer and thats it?
then i launch HardSPLWrapper_Blackstone.exe
follow the steps..
then im done?
Click to expand...
Click to collapse
Yes you need to extract it from zip as it will not run from within zip folder
Personally I ran it just from the desktop, i.e. I put HardSPLWrapper_Blackstone.exe on my desktop
when you have your phone connected and in bootloader mode at the bottom on the screen it should say 'usb'.
then launch HardSPLWrapper_Blackstone.exe, follow steps, then your done.
As I said put phone back into bootloader mode afterwards and verify the screen shows 1.14.OliNex, which is the Hard-SPL version.
Long story short my phone worked fine for months. Went to a 1.56 Rom active sync stopped working. I have already tried everything associated with AS problem, everything. Went to get it repaired at HTC America in Houston, TX there gay and dont support T8285. I have tried flashing via memory card but I seem to be retarded doing it that way. Engineer said mini usb slot works fine, cooked rom may have corrupted AS. Customer service would not let him fix my phone because it was an "aussie version". I just want the phone to sync is that too much to ask? Anyway $100 bucks to anyone that can make it work paid via paypal immediately.
moved out of development
Personally I think your mad offering $100. I'm sure most people would have hepled you for free, including myself. I'm not after your money but offer my assistance.
Have you tried doing a hard reset? uninstalling activesync & reinstalling it?
Flashing different rom. If you can't flash through SD Card, have you tried flashing again via usb. You don't need phone sync'd
Put your phone into bootloader and then connect to pc via usb. At bottom of screen the text should change from 'serial' to 'usb'. Now flash phone by running rom (cooked or stock etc) you downloaded. Put .nbh and ruu file into same folder and then open ruu file and follow instructions.
I severely doubt cooked rom affected activesync.
EDIT
As bonesy said below, you'll need either USPL or HSPL to flash 1.56+ based rom.
Full tutorial or dummies guide to flashing 1.56+ based roms can be found in cRaCKwHoRe's guide. See my signature
Turn off your phone, Take out your memory card, Plug the miniUSB in then power on (Hold volume down press power holding volume down still) This will bring up a coloured screen. Run the ROM Wrapper package exe (BlackstoneRUUWrapper) This SHOULD now install the right ROM.
Please make sure you are using a 1.56 rom with the HSPL or i think it has problems with GFX.
When windows loads go to start>settings>connections>USBtoPC
this is on 6.5 rom not sure about 6.1 :/
Untick Enable faster data synchronizaion, I had to do all this on works computer to update a ROM god knows why but this was my fix.
ROM Should load as should activesync now.
Please let me know if this helps
Tried to post in ure original threads but mods were moving to trash each time BAH!
Thanks to both of you guys for your suggestions. I thought I was not a noob when it came to flashing roms but once I could not do it via usb I was a whole different story. Yeah I am offering the $100 just to get people to help. I know you get slammed if you ask a question so I figured I would make it worth someone's time. I am going right now to pick it up from the repair center so I will try during my lunch in about an hour.
Fallen Spartan said:
Personally I think your mad offering $100. I'm sure most people would have hepled you for free, including myself. I'm not after your money but offer my assistance.
Have you tried doing a hard reset? uninstalling activesync & reinstalling it?
Flashing different rom. If you can't flash through SD Card, have you tried flashing again via usb. You don't need phone sync'd
Put your phone into bootloader and then connect to pc via usb. At bottom of screen the text should change from 'serial' to 'usb'. Now flash phone by running rom (cooked or stock etc) you downloaded. Put .nbh and ruu file into same folder and then open ruu file and follow instructions.
I severely doubt cooked rom affected activesync.
Click to expand...
Click to collapse
I tried uninstalling and reinstalling active sync. Different cables, different computers, xp and vista, everything, checked usb enhanced, etc ,etc.
bonesy said:
Turn off your phone, Take out your memory card, Plug the miniUSB in then power on (Hold volume down press power holding volume down still) This will bring up a coloured screen. Run the ROM Wrapper package exe (BlackstoneRUUWrapper) This SHOULD now install the right ROM.
Please make sure you are using a 1.56 rom with the HSPL or i think it has problems with GFX.
When windows loads go to start>settings>connections>USBtoPC
this is on 6.5 rom not sure about 6.1 :/
Untick Enable faster data synchronizaion, I had to do all this on works computer to update a ROM god knows why but this was my fix.
ROM Should load as should activesync now.
Please let me know if this helps
Tried to post in ure original threads but mods were moving to trash each time BAH!
Click to expand...
Click to collapse
Thanks for breaking it down barney style for me. I will try this very soon. If it works my friend you got $100 smackers.
no worries, Glad to help (if it does lol)
bonesy said:
Turn off your phone, Take out your memory card, Plug the miniUSB in then power on (Hold volume down press power holding volume down still) This will bring up a coloured screen. Run the ROM Wrapper package exe (BlackstoneRUUWrapper) This SHOULD now install the right ROM.
Please make sure you are using a 1.56 rom with the HSPL or i think it has problems with GFX.
When windows loads go to start>settings>connections>USBtoPC
this is on 6.5 rom not sure about 6.1 :/
Untick Enable faster data synchronizaion, I had to do all this on works computer to update a ROM god knows why but this was my fix.
ROM Should load as should activesync now.
Please let me know if this helps
Tried to post in ure original threads but mods were moving to trash each time BAH!
Click to expand...
Click to collapse
So I got my phone and this is what it says.
BLAC120 32M
SPL-1.56.01Olinex
MicroP-Blackstone (LED) v6
and it's just red green blue and white no word on the bottom. Ran BlackstoneRUUWrapper with the nbh file that I wanted and it gave me a connection error. Now it says Seiral in the white.
Fallen Spartan said:
Personally I think your mad offering $100. I'm sure most people would have hepled you for free, including myself. I'm not after your money but offer my assistance.
Have you tried doing a hard reset? uninstalling activesync & reinstalling it?
Flashing different rom. If you can't flash through SD Card, have you tried flashing again via usb. You don't need phone sync'd
Put your phone into bootloader and then connect to pc via usb. At bottom of screen the text should change from 'serial' to 'usb'. Now flash phone by running rom (cooked or stock etc) you downloaded. Put .nbh and ruu file into same folder and then open ruu file and follow instructions.
I severely doubt cooked rom affected activesync.
EDIT
As bonesy said below, you'll need either USPL or HSPL to flash 1.56+ based rom.
Full tutorial or dummies guide to flashing 1.56+ based roms can be found in cRaCKwHoRe's guide. See my signature
Click to expand...
Click to collapse
Well I get it into bootloader no problem but then plug in the usb cable and nada, it says serial. So then I tried starting bootloader mode with the cabe and still nada, it does not even say serial. If I unplug it then it says serial. I have tried both ways to run the RUU Wrapper and I keep getting the usb conncetion error
serial?
Hi, please can you post a screen shot of where it says serial at boot screen?
stoolzo said:
Hi, please can you post a screen shot of where it says serial at boot screen?
Click to expand...
Click to collapse
I cant because I cant use my software that would do that since it wont sync to my computer.
snap shot
just take a snap shot with a webcam or digital camera if you have one.
stoolzo said:
just take a snap shot with a webcam or digital camera if you have one.
Click to expand...
Click to collapse
let me see if this comes thru ok.
turcomora said:
let me see if this comes thru ok.
Click to expand...
Click to collapse
Here yo go. This picture is with me having the device plugged in it charging fine. Then entering bootloader mode. If I unplug then it will say serial. If I dont plug in before then enter bootloader it will say serial still.
thanks
ok, that looks pretty normal,so to recap you fully powerdown the phone by taking the battery out, put the cable into both the phone and pc and the turn on holding volume down and it just sits there?, what happens when you press volume up at this point?
stoolzo said:
ok, that looks pretty normal,so to recap you fully powerdown the phone by taking the battery out, put the cable into both the phone and pc and the turn on holding volume down and it just sits there?, what happens when you press volume up at this point?
Click to expand...
Click to collapse
Only thing I was not doing was taking out the battery. Just tried that and still same screen. Nothing happens when I press the volume up button just stays there.
pc
do you have another pc to try this on to rule out an actual active sync problem?
stoolzo said:
do you have another pc to try this on to rule out an actual active sync problem?
Click to expand...
Click to collapse
Yeah I have been trying on my latop, home pc, and work pc and nothing same result. I have tried different usb cables, os, reinstalling, everything. Only thing I have not tried is flashing via sd card yet.
brick
its sounds like you have a corrupt spl, it is definately worth trying the sd card as it may allow you to activesync but it may then fallover when it reboots and goes into boot mode. This i where user viperbjk (see android dev thread) may be able to help as he has successfully managed to unbrick a phone.
I had this same problem but powering down and simply triggering the and spl reflash resolved it. your problem sounds different though.
I tried flashing the following to my HD2. Other ROMs have worked fine.
Duttys_Leo_Sense_2.5_5.2.23540.5.5.0_2.10_HG_V1_Radio_2.08.50.08_2_WWE
This time, when resetting it's hanging on the O2 screen. This means I can't get into the phone to try reflashing. How do I fix this please?!!!
craigpyro said:
I tried flashing the following to my HD2. Other ROMs have worked fine.
Duttys_Leo_Sense_2.5_5.2.23540.5.5.0_2.10_HG_V1_Radio_2.08.50.08_2_WWE
This time, when resetting it's hanging on the O2 screen. This means I can't get into the phone to try reflashing. How do I fix this please?!!!
Click to expand...
Click to collapse
You should take a look at the mtty thread if you want to recover from a bad flash...
Grtz,
Degake
Crap. I know nothing about this. noob!
This is going to be long and difficult isn't it?
craigpyro said:
Crap. I know nothing about this. noob!
This is going to be long and difficult isn't it?
Click to expand...
Click to collapse
If you post your problem in that thread, the experts over there will give you all the detailed steps and it won't be so bad after all
And I think that anything would be better than to buy a new HD2?
Grtz,
Degake
No, but you shoulda read the n00b flashing guide before flashing...do you have HSPL on your phone? Do you have it SIM-unlocked? Did you flash using activesync or sd card?
EddyOS said:
No, but you shoulda read the n00b flashing guide before flashing...do you have HSPL on your phone? Do you have it SIM-unlocked? Did you flash using activesync or sd card?
Click to expand...
Click to collapse
I did. I have most rcent HSPL, flashing using activesync and have done 4 "successfull" ROM upgrades.
This one appeared to be fine but when it did auto-reset it's now hanging and not booting into anything useful.
Thanks degake.
If a hard reset doesn't help then MTTY might be the only way out
Problem FIXED
Solution: Followed these steps
"This will remove the need for users, x64 in particular, to use “Unsigned Drivers.” Also since in Vista SP2 (x64 & x86) they removed the “F8” options Completely!
Files Needed:
Driver Signature Enforcement Overrider
Remove Watermark V0.8
1: Run the Driver Signature Enforcement Overrider and select “ENABLE TEST MODE” and Press Next
2: There will be a warning to REBOOT, Press “OK”
3: Go Back to Driver Signature Enforcement Overrider Select “Exit” then Click “Next”
4: REBOOT
5: Run the “Remove Watermark V0.8” for you OS type (x64 or x84)
6: In the Command Window type “Y” and wait for the process to complete
7: Once complete REBOOT your system and begin the driver install"
listed in post 2
http://forum.xda-developers.com/showthread.php?t=623356
Then
*Bring device into bootloader (Reset + Hold Vol Down), This will show the Red, Blue, Green screen showing "Serial"
From here I was able to re-run the customRRU file to flash the ROM again. (this may have been jumping the gun a little!)
Thanks for pointing me in the right direction guys.
that'll be MTTY!! Only had to use it once myself but it's a god send
EddyOS said:
that'll be MTTY!! Only had to use it once myself but it's a god send
Click to expand...
Click to collapse
Too True!!
How is liverpool? ive not been there for a while!! (Southport )
SS
Hi folks,
Had the same problem today with a bad flash, phone wouldnt boot up past o2 welcome screen etc etc.
I fixed it by just going into bootloader (hold volume down button on the side of the device while holding the power button down for 3 seconds) and installing the o2 stock (1.43) rom from my pc.
Edit: Cant seem to post the link as im a new user but "Football" posted it on this forum on 23rd of December if you need to search for it.
Sorry if this seems like a double post of the OPs solution but some people could be confused by the MTTY thread (I was) when in reality theres no need to even look at it.
Hope this helps someone.
Greg
Thanks for posting that comment. I did wonder if MTTY had anything to do with the solution (I dont even understand properly what MTTY is!) so I posted everything I did.
I had a feeling that I could have avoided those steps and just gone straight to the bootloader and you've proved me right. it's a quick and easy solution to a slightly scary problem!