Related
i tried flashing a rom to my wizard and now it just freezes at the cingular screen where it shows the version, etc
please help?
Is your phone CID unlocked?
thanks for responding! i followed mun's steps of unlocking it so i think i did.
What's your IPL/SPL?
it says 2.25.001 for both
TaurusBullba said:
What's your IPL/SPL?
Click to expand...
Click to collapse
excuse me sorry it's 2.25.0001
3 0s, it's a g4
livejamie said:
excuse me sorry it's 2.25.0001
3 0s, it's a g4
Click to expand...
Click to collapse
Well, I'd hop back into the bootloader screen and reflash your carrier ROM. Then read over these instructions a couple more times and try again.
Also, before we get ahead of ourselves, what ROM did you try flashing in the first place?
TaurusBullba said:
Well, I'd hop back into the bootloader screen and reflash your carrier ROM. Then read over these instructions a couple more times and try again.
Also, before we get ahead of ourselves, what ROM did you try flashing in the first place?
Click to expand...
Click to collapse
actually i just figured that out on my own. but i appreciate you answering.
i was trying to flash the touch version of nbd when this happened using those exact instructions from mun's thread.
i'm scared now lol.
i'm going to try the windows titanium rom now.
livejamie said:
actually i just figured that out on my own. but i appreciate you answering.
i was trying to flash the touch version of nbd when this happened using those exact instructions from mun's thread.
i'm scared now lol.
i'm going to try the windows titanium rom now.
Click to expand...
Click to collapse
No reason to worry too much. The Titanium ROM is "G4 safe" (it has no IPL/SPL or radio). Just read those instructions I linked to previously and don't skip any steps and you'll be fine.
Good luck!
TaurusBullba said:
No reason to worry too much. The Titanium ROM is "G4 safe" (it has no IPL/SPL or radio). Just read those instructions I linked to previously and don't skip any steps and you'll be fine.
Good luck!
Click to expand...
Click to collapse
is there any reason why the crossbow version of nbd would work but the touch version wouldn't?
livejamie said:
is there any reason why the crossbow version of nbd would work but the touch version wouldn't?
Click to expand...
Click to collapse
Could have just been a bad flash. That's pretty common.
TaurusBullba said:
Could have just been a bad flash. That's pretty common.
Click to expand...
Click to collapse
it happened again, i started this thread here to discuss it more:
http://forum.xda-developers.com/showthread.php?p=1376025#post1376025
I've made the Hard-SPL to upgrade my rom. Ok.
If I want to come back to original Italian ROM is possible to come back also with Hard-SPL to original?
Sorry for my bad english.
Thank You.
alepas72 said:
I've made the Hard-SPL to upgrade my rom. Ok.
If I want to come back to original Italian ROM is possible to come back also with Hard-SPL to original?
Sorry for my bad english.
Thank You.
Click to expand...
Click to collapse
We do not know yet...
Offical rom does not overwrite hard-spl.
u need a sspl to come back. olipro would provide that.
Mod edit: Personal insults not permitted
Olipro said:
firstly, why do you want to? my assumption is that you're a moron.
Click to expand...
Click to collapse
Hi Olipro,
We know hard-spl is the best on our device, but for example in Hungary service said not offical software component (for example hard-spl) void warranty...
When I took my Triniy to service, I had to restore the offical base...(ipl, spl, os, radio).
But of course if everything works, hard-spl stays on pda!
AND THANKS FOR HARD-SPL
fktsndr said:
...but for example in Hungary service said not offical software component (for example hard-spl) void warranty...
Click to expand...
Click to collapse
In Greece also.
well fine...
run the Hard-SPL updater, as soon as it puts your phone in bootloader and asks you to replug USB... DON'T... wait for the RUU on the PC to timeout and exit, NOW replug the USB, flash a normal ROM.
Thank you.
Olipro said:
well fine...
run the Hard-SPL updater, as soon as it puts your phone in bootloader and asks you to replug USB... DON'T... wait for the RUU on the PC to timeout and exit, NOW replug the USB, flash a normal ROM.
Click to expand...
Click to collapse
It seems not working..
Process stops at 14%...
Back to bootloader, there is still Oli
fktsndr said:
It seems not working..
Process stops at 14%...
Back to bootloader, there is still Oli
Click to expand...
Click to collapse
You Need to flash an Official ROM for the SPL to revert back
reyjabs said:
You Need to flash an Official ROM for the SPL to revert back
Click to expand...
Click to collapse
Situation: I have hard-spl and offical HTC wwe rom on my pda.
I did exactly what Oli said, and of course I wanted to flash the offical rom again.
Process stops at 14%!
Not working....
Olipro said:
firstly, why do you want to? my assumption is that you're a moron.
Click to expand...
Click to collapse
Are you sure?
If I want to sale your pda (ebay?) for the warranty?
I'm pefect normal I think no?
Attention please!!!
fktsndr said:
Situation: I have hard-spl and offical HTC wwe rom on my pda.
I did exactly what Oli said, and of course I wanted to flash the offical rom again.
Process stops at 14%!
Not working....
Click to expand...
Click to collapse
Olipro, do you have any new idea?
Looks like Olipro does'nt want us to go back to original SPL
kutonglupa said:
Looks like Olipro does'nt want us to go back to original SPL
Click to expand...
Click to collapse
That's not true. He's just a bit busy at this time but he'll get back to you as soon as he can.
or u people cant read and are doing it wrong? (idk maybe u are doing it correctly and olipro messed up something)
Pawel062 said:
or u people cant read and are doing it wrong? (idk maybe u are doing it correctly and olipro messed up something)
Click to expand...
Click to collapse
Either of which is definitely true.
Pawel062 said:
or u people cant read and are doing it wrong? (idk maybe u are doing it correctly and olipro messed up something)
Click to expand...
Click to collapse
I hope I can read
I tried the method exactly what oli said...it is not working
Could you try it too?
I tried but also stuck at 14% and stucks in bootloader after each reset
I've tried it a hundred times and it does'nt work. Might as well forget it. The procedure just suck and we're not even getting a decent reply except being sweared at.
After formating my athena it automatically starts to install something!
Does anyone know what it installs and if it is possible to stop it from doing that?
I want to make a new fresh installation and only install programs that I like and want!
I have the original WM6 rom!
Please help!
I think you are seeing the device initialization, something that HTC has inserted into the ROM installation process. Not something you want to stop if you want the drivers so everything works.
It is the Extended ROM - basically all the customisation your carrier installs.
But why on earth use a standard ROM rather than an AP one?
Confucious said:
It is the Extended ROM - basically all the customisation your carrier installs.
But why on earth use a standard ROM rather than an AP one?
Click to expand...
Click to collapse
AP one?
I am not familiar with that, what is it?
Thanks in advance!
AP = Athena Project
A group of very clever people have created ROMS for the Athena with all the good biots and none of the bad bits.
The latest version is 3.0 Dual at http://forum.xda-developers.com/showthread.php?t=346221
But 4.0 is finished and will be released when the unlocker is ready.
Thank you so much!
Confucious said:
AP = Athena Project
A group of very clever people have created ROMS for the Athena with all the good biots and none of the bad bits.
The latest version is 3.0 Dual at http://forum.xda-developers.com/showthread.php?t=346221
But 4.0 is finished and will be released when the unlocker is ready.
Click to expand...
Click to collapse
Thanks, will check it out now!
branko.savic said:
Thanks, will check it out now!
Click to expand...
Click to collapse
If I install the AP 3 Rom, will I void my warranty?
yes, because you have to use olipro's unlocker first so your device can be super CID
edit: your original question - i think but im not for sure be if you stick the stylus in the back and and do a soft reset right before the customizations start then next time your phone loads it wont load that stuff but there is some stuff in there you might want.
irus said:
edit: your original question - i think but im not for sure be if you stick the stylus in the back and and do a soft reset right before the customizations start then next time your phone loads it wont load that stuff but there is some stuff in there you might want.
Click to expand...
Click to collapse
Quite Correct! A soft reset during the three second warning will bypass the customizations. No harm in trying it without the customizations, then do a hard reset and let them install. If you don't need any of the extras, you can hard reset again and bypass again with the soft reset.
branko.savic said:
If I install the AP 3 Rom, will I void my warranty?
Click to expand...
Click to collapse
Yes - although you can flash back to an official ROM your device will have to be super CID - but most operators don't notice the super CID and people have claimed off their warranty successfully. One person recently got their device back from T-Mob and it was CID locked again!
Hi there.
I've been wondering and searching 4 a way to undo the HardSpl to its original SPL. The hTC Thailand has just announced that all the device that has been Hard-spl, its warranty will be no longer available. So I want to undo it before going for service. And Hard-spl again when it is back cause there will be no fun without it.5555+
Some of my friends said it could be find in here but i'm not found it yet.
So any link or clue will be appreciated. Thank in advanced, mate.
Maybe here
http://forum.xda-developers.com/showthread.php?t=381600
second post
Thank you. This sure save many people who using polaris in Thailand
As i know, HTC will check the cid if the Polaris is taken for repair. Restore spl will not restore the original cid. How to backup & restore the cid?
fktsndr said:
http://forum.xda-developers.com/showthread.php?t=381600
second post
Click to expand...
Click to collapse
wvillas said:
As i know, HTC will check the cid if the Polaris is taken for repair. Restore spl will not restore the original cid. How to backup & restore the cid?
Click to expand...
Click to collapse
HARD-SPL not owerwrite CID-LOCK only ignore it.
If you flash back original spl, you device will be cid-locked again.
And what can I do about it ?
Fettsrud said:
And what can I do about it ?
Click to expand...
Click to collapse
Hi,
Can you get into bootloader?
Power on and hold volume button down.
Can you get into tri-color screen?
malybru said:
Hi,
Can you get into bootloader?
Power on and hold volume button down.
Can you get into tri-color screen?
Click to expand...
Click to collapse
Yes ! I do!
Fettsrud said:
And what can I do about it ?
Click to expand...
Click to collapse
u need to give more informations about the problem u have ...there.s a lot of things that might brick ur phone and each one has its own solution ...
Fettsrud said:
Yes ! I do!
Click to expand...
Click to collapse
Hi,
Then your phone is not bricked.
mootmetal said:
u need to give more informations about the problem u have ...there.s a lot of things that might brick ur phone and each one has its own solution ...
Click to expand...
Click to collapse
When i start up the phone, only the "HTC" logo appears on a white screen, and nothing else happends.
I was trying some guides to get a NAND version of android on the phone, but now it's just like this..
Fettsrud said:
When i start up the phone, only the "HTC" logo appears on a white screen, and nothing else happends.
I was trying some guides to get a NAND version of android on the phone, but now it's just like this..
Click to expand...
Click to collapse
did u try to install everything ..task29,radio,magldr,recovery and finaly flashing ur rom ?
mootmetal said:
did u try to install everything ..task29,radio,magldr,recovery and finaly flashing ur rom ?
Click to expand...
Click to collapse
i guess i installed it in the wrong order or something..
i didn't read everything, something i really regret now!
Here's the thing:
If you are posting in this section or the WP7 section then you didn't brick your phone. If you are posting in the WinMo 6.5 section then you may have.
You can't brick your phone doing anything Android related.
Flashing task29 then magldr will solve your issue, then just reflash your Android ROM.
orangekid said:
Here's the thing:
If you are posting in this section or the WP7 section then you didn't brick your phone. If you are posting in the WinMo 6.5 section then you may have.
You can't brick your phone doing anything Android related.
Flashing task29 then magldr will solve your issue, then just reflash your Android ROM.
Click to expand...
Click to collapse
can I use hd2 toolkit? or do you recommend something else ?
orangekid said:
Here's the thing:
If you are posting in this section or the WP7 section then you didn't brick your phone. If you are posting in the WinMo 6.5 section then you may have.
You can't brick your phone doing anything Android related.
Flashing task29 then magldr will solve your issue, then just reflash your Android ROM.
Click to expand...
Click to collapse
yes u can brick ur phone my freind lost his phone forever trying to install android ...and i did brick it one and i lost the reboot option ...icant use it and if i do the phone stuck on htc logo ...now i need to wait 2 mn after shuting down the phone befor tutning it on ...otherwu'isr it doesnt boot ...and i have this probleme only on android ...
Fettsrud said:
can I use hd2 toolkit? or do you recommend something else ?
Click to expand...
Click to collapse
Hi,
Toolkit is good.
orangekid said:
Here's the thing:
If you are posting in this section or the WP7 section then you didn't brick your phone. If you are posting in the WinMo 6.5 section then you may have.
You can't brick your phone doing anything Android related.
Flashing task29 then magldr will solve your issue, then just reflash your Android ROM.
Click to expand...
Click to collapse
Now it works! THANKS!!!
mootmetal said:
yes u can brick ur phone my freind lost his phone forever trying to install android ...and i did brick it one and i lost the reboot option ...icant use it and if i do the phone stuck on htc logo ...now i need to wait 2 mn after shuting down the phone befor tutning it on ...otherwu'isr it doesnt boot ...and i have this probleme only on android ...
Click to expand...
Click to collapse
you can't brick your phone flashing Android or WP7 because magldr is flashed over HSPL and you can always get into HSPL provided you didn't do something wrong from HSPL like flashing a bad radio or something. If your Android ROM is fubar you can always reflash magldr from HSPL.
Sorry about your friend and your own phone, but you are either experiencing bad Android ROMs,. kernels, or hardware issues with the phone itself.
Fettsrud said:
Now it works! THANKS!!!
Click to expand...
Click to collapse
np man, glad you got it