Database Users

T-mobile Mda stuck on boot screen

I have a cid and sim unlocked T-mobile mda running Wm5. Problem is now when I boot up the device it hangs @ the T-mobile boot screen. I have
ipl 2.26
spl 2.26
Gsm 02.25.11
os 2.26.10.2
Any help plz guys
EDIT... FIXED THE PROBLEM Found this in and it worked...
Ok here´s how I done it.
First, I must explain what was the problem.
After update the firmware (not actually upgrade, I had the phone full of trash, so I decided to reflash same firmware v2.18 PTG), the Qtek 9100 / HTC Wizard freezed at 2nd splash screen (the one that shows OS versions IPL version, ect). Tried many different versions, upgraded to 2.24, 2.25, downgraded even to 1.6.7.3, but always same problem, freezed on second splash screen. I read many topics on xda-dev, and seen some people with same problem. Apparently there was 2 solutions. 1- send phone back to warranty. 2- write backup ROM from SD in bootloader.
Passed more then 15 hours asking for this SD backup everywhere, and COULDN´T find any help. Apparently no one had this "SD dump ROM Backup".
So here´s how I solved my problem
1- I tought that a SD backup was needed, and yes it is. But u can use your own phone and your own SD to do it.
2- Get a clean SD card (in qtek 9100 / Htc Wizard case is MiniSD) with 128MB (some people say 64MB, but I personally used a 128MB, maybe a 64MB is enough)
3- Kill (task manager) wescomm.exe (this is related with activesync installed on your PC). Insert the blank SD card on the phone.
4- Get your phone in bootloader mode. Like this : Phone powered off, press Camera button + Power On, will enter in bootloader mode (RGB screen).
5- Now connect your USB cable to your phone. And start MTTY_updateROM.exe (http://wiki.xda-developers.com/uploads/romupdate.rar). After open, on Port selection, choose \\.\WCEUSBSH001 and press OK. A window will open with a blank sheet.
6- Type "r2sd all" and hit enter... wait to the end (at end shows "cmd>"). On your phone screen u can follow backup progress... small bar will appear down the RGB screen.
7- Power off the phone (or remove battery), enter bootloader mode (camera button + power on) and this time RGB won´t appear right away. Will ask if u want to "download SD image", press voice dial button to agree, and writting will begin. Wait to the end. Power off and power on normally. Now your phone should be working ok. Not even needed to reflash the phone after this.
Thanks to all and hope this helps more people with this problem

5- Now connect your USB cable to your phone. And start MTTY_updateROM.exe (http://wiki.xda-developers.com/uploads/romupdate.rar). After open, on Port selection, choose \\.\WCEUSBSH001 and press OK. A window will open with a blank sheet.
The only Port Selections available are:
COM1
COM2
COM3
COM4
COM5
What am I doing wrong?

i got the same problem too
only com1 and com2 r there
pleace help me

Yes please someone help!
I want to try this, too, but my mtty tool only shows some com-ports and not WCEUSBSH001 ! what's wrong?
Does this work with mini sd cards bigger than 128 mb, too? is there a limit?

ok, I have the right port in mtty tool now, but...
when I enter "r2sd all" and press enter it says this:
r2sd all
***** user area size = 0x77F00000 Bytes
R2SDBackup() - Download type = 5
usTotalBlock = 1 sizeof(SDCARD_SIGNATRUE_TABLE)=512
You didn't get the proper security level to download a specific image
Cmd>
what can I do?
any help is greatly appreciated!

Four colors screen after radio 1.58.25.14 upgrade

Hello,
After I tried to upgrade my Polaris Radio Rom to version 1.58.25.14, instalation stoped at 99%.
Now when I just turn on my device without USB cable connected I get always the Four colors screen. ( POLA100 ; SPL-1.25.0000; CPLD-2)
I already tried to upgrade many times the radio rom, the full rom, according with the described on 'How to guide: HardSPL ' but when I try to upgrade the info about Image version at the 'Step 4' doesn't appear, and at this step the device already presents the evolution bar stopped at 0% and doesn't pass this...
After a while I get always the same message 'ERROR [262]: UPDATE ERROR'.
What can I do to RESOLVE THIS PROBLEM ?
PLEASE HELP ME !?
Thank you in advance !

i think u shuld wait, coz it takes somtime on 99%

sorry ... you havent read all threads about radio rom flashing carefully!
download the programm mtty and use the command "boot" to start you OS again. then you must flash hardspl. after that ... you can flash a radio rom.
your device isnt bricked or damage!

You can try this....
1. Stop ActiveSync
2. Open Task Manager (press Ctrl + Alt + Delete) on your PC and
stop these two processes rapimgr.exe and wcescomm.exe
3. Plug in your device via USB. Your computer should be asking install a driver. Install and continue.
4. Now Run mtty and choose USB in 'PORT'
4. type "set 16 0" without the quotes to tell bootloader to boot the OS after reset.
5. type "task 8" to get your device formatted.
6. Now unplug your device and manually reset it.
Should work... I used it a while back with a Hermes and I just guided someone else with the same problem as you through it.... and it worked.

I can confirm that the method indicated by Christonge works fine
PQillu,

Thanks mates !
It worked, I finally have my Polaris alive !

disable under Vista
I would like to disable the Center of synchronisation under Vista and I have no idea how to do.

epsimax said:
I would like to disable the Center of synchronisation under Vista and I have no idea how to do.
Click to expand...
Click to collapse
Welcome to the forum, mate, but please post specific questions
in specific threads meant for that (not being offensive 2U though)
In your case I would suggest THIS ONE
Cheers, Olioaglio

christonge said:
You can try this....
1. Stop ActiveSync
2. Open Task Manager (press Ctrl + Alt + Delete) on your PC and
stop these two processes rapimgr.exe and wcescomm.exe
3. Plug in your device via USB. Your computer should be asking install a driver. Install and continue.
4. Now Run mtty and choose USB in 'PORT'
4. type "set 16 0" without the quotes to tell bootloader to boot the OS after reset.
5. type "task 8" to get your device formatted.
6. Now unplug your device and manually reset it.
Should work... I used it a while back with a Hermes and I just guided someone else with the same problem as you through it.... and it worked.
Click to expand...
Click to collapse
Nice one, mate!!!

christonge said:
You can try this....
1. Stop ActiveSync
2. Open Task Manager (press Ctrl + Alt + Delete) on your PC and
stop these two processes rapimgr.exe and wcescomm.exe
3. Plug in your device via USB. Your computer should be asking install a driver. Install and continue.
4. Now Run mtty and choose USB in 'PORT'
4. type "set 16 0" without the quotes to tell bootloader to boot the OS after reset.
5. type "task 8" to get your device formatted.
6. Now unplug your device and manually reset it.
Should work... I used it a while back with a Hermes and I just guided someone else with the same problem as you through it.... and it worked.
Click to expand...
Click to collapse
how can i get mtty and how its work?

christonge said:
You can try this....
Very very cool!!!
I have my Polaris back now !!!
Tanks !!!
Click to expand...
Click to collapse

>> type "task 8"
this step is really optional. no need to re-format if you stucked in bootloader mode usually. device will boot after "set 16 0". this command sets device to use normal mode instead of bootloader mode upon reset.
ommiting the task 8 will save you from reinstalling all you programms again and form other data losses associated with hard reset.

Hermes (TyTN) Call Duration Reset

Hi. Please tell me a metod to reset call duration at HTC TyTN.

This is for personel use, not to resell on ebay as "NEW"...
How to reset call timer (if you want to know reason why you want to do this, please do additional research)
a). Please make sure that you are SuperCID and you understand the importance of hard spl as this maybe a dangerious operation for you.
b). Make sure that you have SPL 1.10 Olipro (this one works for me, higher version seems not work)
c). Download Mtty.exe and save it to your computer.
d). Open connection setting of your activesync or WMDC on your PC and disable "Allow USB connection".
e). Put your device into Bootloader mode and connect to your PC via USB
f). Run Mtty.exe from your PC
g). Select "USB" in port box and then click OK
h). Press Enter once or twice to let the screen dispay "USB>" or "CMD>"
i). Type "rtask b" and Enter then it should show result "0"
j). then type "ate1" and Enter then it should show result "0"
k).then type "atv1" and Enter then it should show result "OK"
l). then type "[email protected]=270f,270f" and Enter then it should show result "OK"
Restart you PPC.... you call timer should be 00.00.00
Cheers....

Where I finde Mtty.exe? Please help.

On the top bar is a little thing called "search", try there....

hello can you say me if this method work for htc tytn 2? thank you

thanks ultramag ...quick answer... some months ago i was curious and had to read many threads to even undestand. thanks

Xperia ROM and Guides

New Generic RTL Xperia ROM images are officially released;
Code:
[I]ROM images[/I]
[B]Customized DE[/B]
http://rapidshare.com/files/155680913/APP_SW_X1i_GENERIC_DE_1213-6439_CDF1215-3303_KOV_R1AA017.image.html
[B]Generic FR[/B]
http://rapidshare.com/files/155700645/APP_SW_X1i_GENERIC_FR_1213-6441_CDF1215-3307_KOV_R1AA017.image.html
[B]Generic IT[/B]
http://rapidshare.com/files/155252393/APP_SW_X1i_GENERIC_IT_1213-6444_CDF1215-3309_KOV_R1AA017.zip.html
[B]Generic SE[/B]
http://rapidshare.com/files/155685806/APP_SW_X1i_GENERIC_SE_1213-2274_CDF1215-3315_KOV_R1AA017.image.html
[B]Customized UK[/B]
http://rapidshare.com/files/154889093/APP_SW_X1i_GENERIC_UK_1213-6450_CDF1215-1832_KOV_R1AA017.zip.html
[B]Customized T-Mobile NL[/B]
http://rapidshare.com/files/155690891/APP_SW_X1i_TMO_NL_1213-2293_CDF1216-0475_KOV_R1AA020.image.html
[B]O2 DE[/B]
http://rapidshare.com/files/155769609/APP_SW_X1i_O2_DE_1213-2272_CDF1215-1634_KOV_R1AA017.image.html
[I]Instructions / Movie / Trouble Shooting[/I]
[B]Working Instructions Guide (Mechanical level) for X1i/X1a[/B]
http://rapidshare.com/files/155696508/Guide_Working_Instructions_Mechanical_X1i.pdf.html
[B]Working Instructions Guide (Mechanical level) for X1i/X1a[/B]
http://rapidshare.com/files/155696939/Guide_Repair_Movies_Mechanical_X1i.pdf.html
[B]Trouble Shooting Guide (Mechanical level) for X1i/X1a[/B]
http://rapidshare.com/files/155697184/Guide_Trouble_Shooting_Mechanical_X1i.zip.html
Code:
[B]How to enter bootloader mode on your Xperia:[/B]
0. Make sure your phone battery is fully charged.
1. Turn off your phone.
2. Remove and reinsert the phone battery.
3. Press and hold first the volume down button on the phone and then the phone power button.
4. Continue holding the two buttons (volume down + power button) down until the phone display turns on and displays colored stripes.
5. Release the buttons.
6. Attach the USB-mini cable to the phone and the PC.
7. Take a cold beer :).
[I]Delay a few minutes, or alternativity take a short nap[/I]
8. Follow included instructions.
9. Read again.
...
10. Start playing with your device
I have also attached some technical guides together with mechanical/electrical repair manuals which includes assembly and disassembly hints, I really do hope the community finds them useful. If you are missing something, don't hesitate to PM me or you can mention in this thread what you really are looking for.
It is required that you've got a security unlocked phone (SuperCID with HardSPL) for being able to use the ROM images linked above!
Regards

thanks a lot

arash_ ! Thanx

awesome, thx for sharing with us

I tried UK IT SE versions, they all stoped at either 10% or 11%.
Now I cant use my phone anymore, it shows a four color screen(red green blue and white),
and says that
KOVS110
SPL-0.72.0000
MicroP1-787
MicroP2-707
Upgrade ROM code error
Please try again
Serial
--
I tried to use RUU to recover the process, but it didn't work, always stops at 10%
I am not an engineer, don't know much about it, could anymore one just tell me how to make my phone work again, I just want the SE system back, I am done with flashing the ROM. thanks

ffffdddd said:
I tried UK IT SE versions, they all stoped at either 10% or 11%.
Now I cant use my phone anymore, it shows a four color screen(red green blue and white),
and says that
KOVS110
SPL-0.72.0000
MicroP1-787
MicroP2-707
Upgrade ROM code error
Please try again
Serial
--
I tried to use RUU to recover the process, but it didn't work, always stops at 10%
I am not an engineer, don't know much about it, could anymore one just tell me how to make my phone work again, I just want the SE system back, I am done with flashing the ROM. thanks
Click to expand...
Click to collapse
the same problem here

any ideas how to unlock that cid?

Its a happy day again !!! Yipiii
1. Download mtty.exe
2. Disable activesync (connection settings -> uncheck "allow usb connections")
3. Connect your x1 to PC using USB cable.
4. Open mtty, select USB port and click OK.
5. Hit ENTER twice, you should see the "Cmd>" prompt.
6. Type the command "boot"
and its alive again but after restart need mtty to boot again.
so realy need to unlock cid to be god flashed

Very usefull thread. For CID unlocking need's HardSPL. arnisv, does this repair dead phones eg. stuck at tricolour (bootloader) screen ?

borce_razor said:
Very usefull thread. For CID unlocking need's HardSPL. arnisv, does this repair dead phones eg. stuck at tricolour (bootloader) screen ?
Click to expand...
Click to collapse
No, it doesn't work on my phone

ffffdddd said:
No, it doesn't work on my phone
Click to expand...
Click to collapse
Try this
Code:
MTTY (How to fix a bad ROM flash!) Hi,
I didn't see any post about using MTTY on Kaiser.
If I did a bad ROM flash with my previous device (HTC Universal), I could always fix this by clearing the FAT table with MTTY.
Believe me... if you flash and it stops ad 85% you will be very happy if you can use this tool!
Reason I started this thread is to help out people who are having such a problem with there Kaiser!
This is the correct procedure to get you out of trouble
1. Stop ActiveSync, by Task Manager (press Ctrl + Alt + Delete)
kill two processes rapimgr.exe and wcescomm.exe
2. put your device into the cradle
3. Run mtty and Choose WCEUSBSH001 in 'PORT' (if it doesn't show then you didn't stop all active sync processes above!)
4. type "set 16 0" without the quotes to tell bootloader to boot the OS after reset. (for some devices it can also be "set 14 0")
5. type "task 8" to get your device formatted
6. type "task 0" to ask your device reboot
7. take the device out of the cradle, and manually reset it if it does not do that already.
Incase of an emergency it could be very helpfull I think!
Thank you all for providing the input in this thread so I could make this small user manual!
Happy flashing!
Search for MTTY ver 1[1].42 or other, this is from our forum. It work's on Kaiser, maybe will work on xperia. And I'M NOT RESPONSIBLE FOR ANY DAMAGE DONE WITH THIS

Xperia HardSPL thread created

What rom is the swedish one? Newer or the same as it was delivered with?
Edit: Im new to windows mobile. What should i look for to check what version i have?

[email protected] said:
What build is the swedish on? Newer or the same as it was delivered with?
Click to expand...
Click to collapse
As i see it, it's the same as we allready have

borce_razor said:
Very usefull thread. For CID unlocking need's HardSPL. arnisv, does this repair dead phones eg. stuck at tricolour (bootloader) screen ?
Click to expand...
Click to collapse
no it just boots the phone in wm and all works exept can not restart the phone without myyt

If you turn off the phone it can't be booted again without mtty ?

borce_razor said:
If you turn off the phone it can't be booted again without mtty ?
Click to expand...
Click to collapse
yes need help of mtty

How its possible know which version have CID? All swedish version have CID but its able to unlock and after that u can flash to English OS?

ok after
Cmd>set 16 0
Cmd>task 14 0
now phone boots without mtty

borce_razor said:
Try this
Code:
MTTY (How to fix a bad ROM flash!) Hi,
I didn't see any post about using MTTY on Kaiser.
If I did a bad ROM flash with my previous device (HTC Universal), I could always fix this by clearing the FAT table with MTTY.
Believe me... if you flash and it stops ad 85% you will be very happy if you can use this tool!
Reason I started this thread is to help out people who are having such a problem with there Kaiser!
This is the correct procedure to get you out of trouble
1. Stop ActiveSync, by Task Manager (press Ctrl + Alt + Delete)
kill two processes rapimgr.exe and wcescomm.exe
2. put your device into the cradle
3. Run mtty and Choose WCEUSBSH001 in 'PORT' (if it doesn't show then you didn't stop all active sync processes above!)
4. type "set 16 0" without the quotes to tell bootloader to boot the OS after reset. (for some devices it can also be "set 14 0")
5. type "task 8" to get your device formatted
6. type "task 0" to ask your device reboot
7. take the device out of the cradle, and manually reset it if it does not do that already.
Incase of an emergency it could be very helpfull I think!
Thank you all for providing the input in this thread so I could make this small user manual!
Happy flashing!
Search for MTTY ver 1[1].42 or other, this is from our forum. It work's on Kaiser, maybe will work on xperia. And I'M NOT RESPONSIBLE FOR ANY DAMAGE DONE WITH THIS
Click to expand...
Click to collapse
Thanks a lot, my phone is working again, although its still in Swedish.

[Q] hw6915 wm6.1 rom

Ok..so first of all thanks for clicking on my thread.I hope somebody can help me flash a rom.I can't post the link because I'm new....I added a text file with the link(yes, it's on xda)
Post #9 describes a process of flashing this rom.
My device: HW6915 vG.39 G4(flash chip)
I am having trouble with this step pdocwrite spl -n0 -b 0x20000 0 0x80000.
Yes I know what the bootloader is and I know how to get into it.So after I connect the device via usb(while in BL mode) i run the command mentioned above.The problem is that nothing happens(screenshot included),it just stays at the same command and does not progress at all.CPU usage is little to none.And if I do try to flash the rom anyway the progress bar on sable_RUU gets stuck at 1% and after a few minutes gives an error.I tried this on XP 32 and on 7 64.
Yes, this is my first post, so take it easy.
Thanks for any help.

hello. i have the same problem but my sable ruu progress bar freezes at 51% and then pop up error:201. help?

For you it's stuck at 51% because you also flashed the bootloader(CEBL.nbf).I chose not to as it's optional.Even so I'm still stuck on the original problem.
Anybody know the answer to this?

my problem is identical. i am also having trouble with pdocwrite spl -n0 -b 0x20000 0 0x80000.after i run the command nothing happens,it just stays at the same command and does not progress at all as in your case. then when i run sable_ruu it freezes at 51%

did you try...
did you try opening the command prompt as administrator?
Code:
1. Click on start
2. Type command
3. Then either right click and then pick run as administrator or just CTRL + SHIFT + Click
If that doesn't work you can try disabling UAC by clicking start, typing UAC pick the first option then dragging the slider to the bottom and restart computer

You need to write SPL when phone is on and connected with ActiveSync, not in bootloader.

Spiaatie said:
You need to write SPL when phone is on and connected with ActiveSync, not in bootloader.
Click to expand...
Click to collapse
Ok it works thanks guys for all the help.
Will report back to your thread and tell you about my findings
Thanks,appreciate it

Thanks from me too. On the first look wm 6.1 runs faster than 5.0 and gps does not work (igo 2006 plus-can not find gps com port).

my suspicions on gps is it might be driver related in asset viewer (Settings/System/MyCPL 7) under GPS it used to state whether it was on or off in WM5 but now it says N/A

jambongo said:
my suspicions on gps is it might be driver related in asset viewer (Settings/System/MyCPL 7) under GPS it used to state whether it was on or off in WM5 but now it says N/A
Click to expand...
Click to collapse
Yes the driver is indeed missing as this is ported from a hp without gps(i guess so anyway).First clue is that it doesn't include any base navigational software.
Second igo 8 reports ''gps driver not found''

n can you! help???
you seem to know how to proceed to tryin' roms on you hw6915;
......i don't!
can u help me, i'm really a newbie on this!!!
i wish there was an "upgrade your ipaq verson for dummies" or somthing!!
i got the hp ipaq hw6915, an usb connector, Internet access!! anything else?

oussahoo said:
you seem to know how to proceed to tryin' roms on you hw6915;
......i don't!
can u help me, i'm really a newbie on this!!!
i wish there was an "upgrade your ipaq verson for dummies" or somthing!!
i got the hp ipaq hw6915, an usb connector, Internet access!! anything else?
Click to expand...
Click to collapse
Beware dude this is higly experimental.There is no GPS for example.The rom is wm6.1.This is just for people who want to test and no it obviously not official.All files can be found at the link in the TEXT file I attached to my first post.
1.Connect your device to activesync(suggest a hard reset first,however it's optional)
2.Extract SPL vG.39.7z anywhere you want.
3.Run ''Command prompt'' (if using vista/7 RUN AS ADMINISTRATOR)
4.Enter this command pdocwrite spl -n0 -b 0x20000 0 0x80000 (WAIT UNTIL IT FINISHES).This command replaces a file in the ROM which allows you to flash ''non-original roms'' basically software CID unlocking which allows flashing of ''cooked roms''
5.You will get warnings on your hp regarding a dll file(itsutils.dll) PRESS YES
6.Put your device in bootloader mode.[hold the two buttons next to the joystick(the round thingy) and shortly tap the reset button with your stylus
7.Open activesync,go to connections and untick allow USB connections
8.Extract 6915_ENG.7z and run Sable_RUU
9.Press on the big ''Upgrade button''
10.There will be a progress bar, when it's done it should say something like '' Update finished !!''
11.Go back to activesync and re-tick allow USB connections
I wrote this for everybody who's got trouble flashing roms on their hw69xx.Yep I had this problem too.
This detailed enough?

jambongo said:
did you try opening the command prompt as administrator?
Code:
1. Click on start
2. Type command
3. Then either right click and then pick run as administrator or just CTRL + SHIFT + Click
If that doesn't work you can try disabling UAC by clicking start, typing UAC pick the first option then dragging the slider to the bottom and restart computer
Click to expand...
Click to collapse
A question ....
but it happens to me the same error in XP and not out of the 1% resulting in the error 201
Can you help me!

hi
I have the hw6915
to me the procedure doesn't go
he/she writes me "client_initialize Fail Error 601"
a question: what I write on the Command Pront
thanks

for further information
the cell doesn't connect him to activesync
it is jammed on screens her/it USB - LOGO HP INVENT and in low vG.39
THANKS

@spiaatie
mine is in bootloader
however it doesn't connect him with Activesync
what do I have to do?
which procedure do I have to do?
thanks

can't program ipaq 6945
When ever I push upgrade button, it just hangs and afer a while I get the message:
client_getosver Fail !! Error :501
I'm using it on windows XP,
could someone help me!!!
Thanks!

rra_pn said:
client_getosver Fail !! Error :501
Click to expand...
Click to collapse
Did you install SPL?

Yes, I did de pdcowrite on command prompt, then it gave me the warning on my ipaq and then it finished.
After that I unticked the allow usb connections on active sync
then I press the two buttons next to the joystick and press the reset
I run sable
and then it does what i Posted
Thanks!