Database Users

I need help to repair my Qtek

Hello
I just did the following :
download the files from www.carrierdevices.com.au for Qtek 101 update
"Qtek 1010 Upgrade
(22102003-190723)-RSUv1.15_(GPRS_T32500_ENG).exe
File Contents
• CE Upgrade File : RUU_CEv3.18.04wwe_Qtek_SHIP.exe
• Radio Upgrade File : RSUv1.15_(GPRS_T32500_ENG).exe
"
When the process began there was an error asking to press OK for restart.
After restarting device in the boot sequence ( when logo is diplayed) there are no informations about the ROM. Just Radion version is diplayed and that is the new version one (3.25)
Also on the display there is no start icon and I cannot use the display because it seems to be decalibrated completly.
Very Important : When I try to connect to Activesync after a while it telling me that the device is not a smartphone or a pocket PC and cannot be connected. So I cant use any program to try to upgrade again.
What to do ?
Please try to give examples and link to download files in order to fix my device.
Thanks in advance
Silviu C.

Hi ...
If you still can get to the boot loader screen (power button + soft reset) and it displays "GSM OK", that means there is a good chance that the flash ROM is not damaged.
You can either put the ROM and RSU files on SD card through a card reader (.nbf files) or to get a valid SD backup for CE + Radio from any working XDA and use the boot loader screen to flash your device again.
Good luck ...

thanks, where I can get some files?
Thank you for your replay,
It seems to be ok cause i can upload a new CE in SD format to the device. ROM was build in the kithcenROM from yorch.net.
It still not working cause perhaps I need the file containing Radio and CE as well in SD format.
Do you know where I can get it ?
I dont think I can get another device to read the files on the SD.
Many thanks,
Silviu C.

I 'm not sure which stage you are stuck with now ... if you can put CE image on SD card and flash it using the boot loader, that means you can boot your XDA and flash the RSU through a normal EXE file from yorch.net .... if this is not the case then you most propably have the wrong file format on the SD card.
Give more details plz

present situation
I am at the edge of disperation.
Steps of what I did :
1. Back up Boot and CE to SD and save them to HDD.
2. Build a CE from Yorch.net in nb1 format and write it to SD with an adaptor.
3. Flash the device with that specific file ( was just CE , not including bootloader)
Now, my pocket is like that:
It cannot been powered from the power button
It start when plug in the charger
I cannot go in bootstrap mode ( when procedure for activating is made I just got a small red flash from the LED)
I have to mention that I choose from the yorch options :" lock butons except power when the device is turned off "
So, now I cannot use the SD for try another flash image.
I cannot use activesync because it cannot recognize the device. Somthing is wrong in the header of the authorising string or something like that.
When I plug the USB cable, activesync is starting but after 10 secs a pop up telling me that the device cannot be recognize, it is not a smartphone or pocket pc.
I am stack.
Thank you
Silviu C.

another question
I have another question:
Is there anywhere - in situation that the problem with boostrap will be solved somehow - full flash containing both radio and CE ?
Thank you,
Silviu C.

some little success
I have suceded by entering in bootrap mode !!
It telling me that I have GSM ERROR
What to do?
IS there any way I can get a full flash for Qtek with radio and OS as well?
Thanks,
Silviu C.

In the boot loader screen, try to press the calendar button ... it should give you the GSM menu. Select "Reset" or "Turn off" and do a soft reset
Plz do NOT try band switching or "Calib/debug"!

It sounds like a failed radio stack upgrade, you can try copying the RSUpgrade.sa.CAB file to your SD card then run it from there.
You can get the RSUpgrade.sa.CAB file by using WinZip to extract it from the RSUv1.15_(GPRS_T32500_ENG)[1].exe file.
HTH

XDA 1 not working

Hi,
I was upgrading the software upgarde on my device. I successfully upgraded the Pocket PC software on the O2 XDA, but when I tried to upgrade the GSM radio/GPRS software of the O2 XDa, it gave some error and after this my device is not starting at all. The only mistake I did was that "I did not remove the SIM card before upgrading the GSM radio/GPRS software" The device does not start even after cold booting the same. When I start the device, the O2 screen comes and after a quite long time the main window does come but I cannot do anything. I tried to tap on contacts, time, tasks but nothing happens. I can see the windows logo wall paper but cannot do anything. Please help on how I can restore back my O2 as a cold reset also does not work. :?
Thanks and Regards
Jinesh

There's many topics about your question in the forum. Search it! Try to search with this keywords: 1% error, repair.zip

There's many topics about your question in the forum. Search it! Try to search with this keywords: 1% error, repair.zip

Hi,
I have tried all the available options but it still does not work. To restore the ROM how do I get access to the O2 cause niether serial nor USB is detecting it.
Please help.
regards
Jinesh

SD card install guide
Ok here you go, its a little outdated but its what I still use:
Qman's how to use XDArit to write nk.nb1 or nk.nbf to your SD card aka the Bootloader Method!
1. Place XDArit and the nk.nb1 or nk.nbf file in the same folder and start XDArit.
2. Select your SD card (disk drive) from the drop down menu.
3. Select Write to SD
Notice that the Windows CE box is already checked so just click the browse button at the end of that window.
4. Select your (nk.nb1 or nk.nbf) image and then Open
Notice by default XDArit will open looking for a *.nb1 file but if you're going to use a .nbf file you'll have to manually change the "Files of Type" to *.nbf
Notice that nk.nbo / nk.nbo was automatically added as your boot-loader and its check box is unchecked so leave it that way and click OK. XDArit should start writing to the card.
When XDArit has finished writing the image put the SD-card into the XDA and hold the power button and soft reset. You'll be taken to the below screen:
SD DOWNLOAD
Card Type:
CE OS & BOOT
Press action to Download
Or
Press REC to Exit
Press action to download and it will start the download/restore from the SD card.
Follow the on screen instructions once its "Completed" which will consist of a "Soft Boot/Reset".
Click to expand...
Click to collapse

Thanks Chief, I will try out and let you know.
regards
Jinesh

Hi Rudegar,
I tried the procedure given by you. I was able to write to the flash successfully. After writing to the flash it gave a message "Checksum OK, Please cold reboot to reset".
I did a cold reboot. After starting the O2, it showed the O2 logo screen and after quite a long time, it asked me wether I want to format the SD card or not. After that it took me to the default screen of XDA wher eit showed options like "Add today's date, Contacts, Schedule etc etc. but upon tapping any of the options the O2 behaves erratically. If I tap on today's date it takes me somewhere else. Inshort it does not work.
I again did a cold reboot and now the device is in its original position i.e not going after the O2 logo where it gets stuck up.
One thing I would like to mention is that all these activities have been done putting the O2 on the cardle only as the battery is totally discharged and the device turns on only after putting it on cradle. Even after the cold reboot it does not start unless I put it on the cradle whichis connected to the mains. Is it Ok with this or am I doing something wrong? The battery does not charge and hence I have to do it in this way.
Please suggest what wrong am I doing? Any suggestions from anyone will be welcome.
regards
Jinesh

Hi,
Someone posted the original O2 ROM on this site and I downloaded the same after which I was partially succesful in flashing the ROM and reviving my dead O2 back to half life. :roll:
I burned the ROM on
to my SD Card and flashed the ROM on to my O2. After
successfully flashing the ROM I rebooted the device.
The device now starts Windows but it takes atleast 15
minutes to start. I get the today screen. WHen I cick
on start the start menu appears after a delay of 10
seconds and all applications run normal, however all
this happens only on the Cradle only.
When I go into the Battery Settings it shows "Battery
Status Unknown".
Also none of the phone functions work. The SIM card is
not recognized and in device information it does
dispaly the "IMEI number" and the "Protocl Version"
I am only able to use inbuilt phone applications.
Is there some problem with my battery cause it is not
charging even on the cradle.
Device Information does not show Radio Version, Protocl Version & IMEI number at all.
Can anyone please help me?

hello all,
it means that your radio stack are dead. Currently, We don't have any real method to fix this problem. When the radio stack is error, you can not upgrade it or do anything to make it work. We can only upgrade or downgrade the radio stack if it works. Also if you try to upgrade the radio stack, we realy need to flash the chip using a speceial tool or need the sd card which build in radio stack with we can only flash in bootloaading mode. Howerver, in some case, we can fix it but .... I think it is just lucky or the xda error when battery problem.... in this case, just disconnect the battery few minutes and connect it again by pressing the battery hole.
Regards,
Hoanghon
p.s. I have dead xda. I killed it when I upgraded the RADIO STACK. Therefore, if you are really need to upgrade the radio stack, I recommend use the official upgrade for secuirity. or just upgrade the rom only.
Note:
To eliminating the error, you need to upgrade the rom or the radio stack, you need to check if the rom fix the radio stack or the stack you are trying to upgrade it fix the rom or not.(ie, Tmobile Rom have to use it radio stack built for Tmobile pocket pc...... I know that in some case when we mix between the radio stack and OS it works but I don't think it work propertly. Anyhow the mixing bettween radio stack and OS is very dangerous if it doesn't suppport then you have to reflash the radio stack or rom(the OS is Okay but the keep upgrading the radio stack may cause the radio stack killed)

WE NEED SERIAL CABLE FOR PDA ANY HELP PLS!!!
Hi Jineshd we
have the same problem and we are sure that the only way is to do SD uptade
and U said U have a serial cable to Yours device. With that we can be able to download flash gsm rom from working device and put it back via SD card to ours. Pls tell me where can I get a serial cable or some schema how to prepare it and I will try to repair ours dead pdas. Its our only chance
rgds
Lukasz

Hi,
Thanks all for the replies.
Can anyone tell me how doI repair the radio stack?
Regards
Jinesh

no way without having special RSU rom update on SD card and run it from bootloader or dissembling the device and reprograming GSM rom on special rom/bios programing socket. (Here on forum is user Cgigate from Toronto CA who can do it but I cant contact him)

Problems!!

If i want to upgrade my wallaby i get an error message in the communications procedure. I have downloaded my ROM from lumpy's kitchen and ive tried to upgrade it many times right now.
Can anyone give me an advise how i could hardflash the ROM of my device?

I think you get an communication error when trying to flash via ActiveSync.
You have to flash via bootloader....
http://wiki.xda-developers.com/index.php?pagename=Wallaby
Here you get furthe rinformation about how to do it....
HTH
Stefan

Nothing yet
Ive tried to Bootload te rom, but after the message "connect your USB now" the device does not react anymore.
I have tried to run the application rom but this says that active sync does not recognize a device.
What should i do next?
Thanks for the quick respond!!

Even if i make a bacup to SD this doesnt work. There no explaination how to hard flash the device! Can you give me an advise???

What have you done exatcly, and where is the problem?
It's not really clear for me.
For Flashing via SD-Card there is no USB connection necessary....
STefan

I have tried to flash with the bootloader. When i push on the on/off putton and do soft reset i see the question "connect to USB now". If i connect and i start the rom nothing happens.
Afterwards i have tried to put the rom on my SD card. I have tried to do this OSimagetools. The pc does recognize the SD card in my wallaby. I also dont have a cardreader.
Is there a way to flash my wallaby in the bootloader-mode with the USB connection?
What do i have to do for it?
Thanks

Strange.
You should see device displays a background that consists of four equally sized vertical bars, colored (from top to bottom) white, red, green and blue. On top of this, it says:
WALLABY
Bootloader
V5.14
WAIT
After a few seconds, the WAIT is replaced by GSM OK. Both messages are in the blue bar, but have a white background.
What do you get?
What is labeld on your rear sticker of the device? (modell) ?
Stefan

Its model: PW10A1
SN: HT220cc15300
PN: 99HJ00007-00
Step 1)I have seen the horizontal bars. And its version 5.18. Ive also seen the "GSM OK"- notification.
Step1a)If i connect it afterwards to my USB nothing happens. The computer does not recognize the Wallaby.
Step2) If i hold the On/Off button i get the message "Connect to USB now" If i do this, activesync does recognize my device and i cannot install the ROM.
Step3) after step 1 i press the contacts button and i see 6 ways to backup my rom or GSM. I have backedup my GSM and ROM to SD. But this has no use for me.
Greetz,

Ok. Now I see.....
First of all, you have an totaly unknown Bootloader (5.18) to me, so i hope all steps will work....
You require a SD-Card with >= 64 MB
XDATools ftp://[email protected]/Wallaby/Tools/XDATools.zip
Your downloaded ROM from my kitchen
step1) Boot your XDA up normal and connect via active sync (guest partnership is ok)
step2) Copy all your data of your sd-Card to your local PC otherwise all data on it will be gone
step3) Enter bootloader of your device by pressing On/Off and doing a softreset
step4) After the Message GSM OK press the Contact Button of your device
step5) Navigate with the pad to "CE+BOOT TO SD"
step6) Confirm this with the Action Key (Press the middle of the Navigate-Pad)
step7) After finishing enter again bootloader by holding On/Off and doing a soft reset
step8) Bootloader should tell you something tah OS is detected on your SD-Card
If No -> Problem
If Yes -> continue
step9) Boot your XDA up normal and connect via active sync (guest partnership is ok)
step10) Install XDATools on your PC
step11) in a dos -box (cmd) go to the directoy where osimagetool is located
step12) enter command: "osimagetool -r xdasdslot -w original.nbf"
step13) enter command: "osimagetool --register"
step14) extract the downloaded ROM using winzip
step15) Run osimagetool
step16) Select the nbf-file in the english-folder of the extracted lROM as source and XDASlot as destination
step17) After finishing enter again bootloader by holding On/Off and doing a soft reset
step18) Bootloader should tell you something tah OS is detected on your SD-Card
step19) Press Action Key to install the ROM
step20) After finishing do a hard reset
step21) Now your ROM should be installed on your device.
step22) Locate the created file original.nbf and compress it using winzip
step23) Upload the compressed file to ftp://xdaupload:[email protected]/Wallaby/Uploads
step24) Enjoy your new ROM
That should be alll .....
;-)
HTH
Stefan

Thanks, But when i extract the rom to a folder, OS Imagetools cannot find the nbf-file. There is no nbf-file in the extracter-rom-folder. I can only find an nb-file.
There is a file called "NK" which says that its an NBF-file(properties). The file is 32MB large. I have tried to select this file (step 16), but the file is not being recognized. Even if i change the extension of the filename. The OSimage does not support this file.
I Have tried this with 3 ROM's : 2003 SE, 2003 and 2002 neither of them contain the nbf-file in the english folder.
Do you have an advice? I think i am very close right now!!
Thanks,

I have sucseeded to install 2002, but 2003 SE wont be recognized. It says its an usupported file.
Has this anyting to do with the fact that i renamed the file? If so can you tell me how to change the file back??
I have downgraded my wallaby to PPC 2002 right now.
Thanks Lumpi!!

WM2003SE couls only be installed via Exe-File. It can not be flashed with the osimagetool.
Stefan

Magician: turn on only in bootloader, can't be flashed

Please, help me in the following situation
I bought Qtek s100 It turns on only in bootloader mode. What was before I don't know.
Now I try to reflash it via PC. I unpacked rom 1.12 from imate and put there file MaUpgradeUt_noID.exe and then ran it. The utility can't see the device information (it is normal) but it can't see the informatin about the rom I'd like to flash. I click @[email protected] but it says it gather information about the device and nothing happened.
I tried to run again about 20 times, but nothing helped.
I tried to flash it via card using rom-image but there is no invitation to reflash though I flashed via card more than 20 times other htc devices and then everything was ok.
I ran mtty 1.42 and gave command d2s, but it said unknown command. Then I gave d2s command then the device turned off.
I have qtek s110 with broken display. Is it possible to change rom-memory?
Is it possible to get service_manual for magician?
Thanks

First of all, did you back up your current ROM to SD before Flashing new ROM.
1. Yes. It's VERY GOOD. Disconnect your device from PC. You need to insert SD with your ROM to the device and Turn On. Press Power or Cancel button (i didn't realy remeber try all). After that device will flash ROM form SD.
2. No. It's VERY BAD. You need to know start address form what device should start after Reset. Sory here i did not know what it is.

Ñïàñèáî çà ïîìîùü!
Ñóòü â òîì, ÷òî àïïàðàò ñ êîìïà øèòüñÿ íàïðî÷ü îòêàçûâàëñÿ. Ïîïðîáîâàë øèòü îáðàçîì ÷åðåç êàðòó (îáðàç ñíÿò ñ t-mobile 1.01). Íà îáðàç íèêàêîé ðåàêöèè.
Äàëåå ïðîáîâàë ñíÿòü îáðàç ñ ïðîáëåìíîãî àïïàðàòà. Àïïàðàò âûêëþ÷àåòñÿ. Åñëè ñ mtty äàòü êîìàíäó øèòüñÿ s2d, òî mtty ãîâîðèò, ÷òî êîìàíäà íåïðàâèëüíàÿ

Hi,
Read this http://forum.xda-developers.com/viewtopic.php?t=46628 about the SD flash
M

thanks, but te problem is the device doesn't want to work with card. No reaction on the card with rom-image, turning off when typing d2s

Don't know where you bought & how much you paid for it (sure hope it's less then a new screen), but sir I guess you're scr*w*d.
Maybe you can replace your broken S110 screen with the one from the S100. There's a rar file on the board, with a detailed description & pictures on howto disassemble your magician, think it's called disassembly.rar.
EDIT You can find it here http://forum.xda-developers.com/viewtopic.php?t=44841
M

thanks, but I think the screen is alive, it shows usb or serial and etc.
As far as i know, there is some diagnostic tests to understand where is the problem. how to activate it?

Diagnostics
Sorry I don't know of a diagnostics test. But you can have a bootloader without a working rom. Since you bought the S100 in a bootloader state, that's very suspicious to me. & that's why I advised you to replace the broken screen on your S110 with the one from your S100.
Hope you can sort it out & if you happen to run across a diag. pls update the wiki with it.
Regards, M

Xperia ROM and Guides

New Generic RTL Xperia ROM images are officially released;
Code:
[I]ROM images[/I]
[B]Customized DE[/B]
http://rapidshare.com/files/155680913/APP_SW_X1i_GENERIC_DE_1213-6439_CDF1215-3303_KOV_R1AA017.image.html
[B]Generic FR[/B]
http://rapidshare.com/files/155700645/APP_SW_X1i_GENERIC_FR_1213-6441_CDF1215-3307_KOV_R1AA017.image.html
[B]Generic IT[/B]
http://rapidshare.com/files/155252393/APP_SW_X1i_GENERIC_IT_1213-6444_CDF1215-3309_KOV_R1AA017.zip.html
[B]Generic SE[/B]
http://rapidshare.com/files/155685806/APP_SW_X1i_GENERIC_SE_1213-2274_CDF1215-3315_KOV_R1AA017.image.html
[B]Customized UK[/B]
http://rapidshare.com/files/154889093/APP_SW_X1i_GENERIC_UK_1213-6450_CDF1215-1832_KOV_R1AA017.zip.html
[B]Customized T-Mobile NL[/B]
http://rapidshare.com/files/155690891/APP_SW_X1i_TMO_NL_1213-2293_CDF1216-0475_KOV_R1AA020.image.html
[B]O2 DE[/B]
http://rapidshare.com/files/155769609/APP_SW_X1i_O2_DE_1213-2272_CDF1215-1634_KOV_R1AA017.image.html
[I]Instructions / Movie / Trouble Shooting[/I]
[B]Working Instructions Guide (Mechanical level) for X1i/X1a[/B]
http://rapidshare.com/files/155696508/Guide_Working_Instructions_Mechanical_X1i.pdf.html
[B]Working Instructions Guide (Mechanical level) for X1i/X1a[/B]
http://rapidshare.com/files/155696939/Guide_Repair_Movies_Mechanical_X1i.pdf.html
[B]Trouble Shooting Guide (Mechanical level) for X1i/X1a[/B]
http://rapidshare.com/files/155697184/Guide_Trouble_Shooting_Mechanical_X1i.zip.html
Code:
[B]How to enter bootloader mode on your Xperia:[/B]
0. Make sure your phone battery is fully charged.
1. Turn off your phone.
2. Remove and reinsert the phone battery.
3. Press and hold first the volume down button on the phone and then the phone power button.
4. Continue holding the two buttons (volume down + power button) down until the phone display turns on and displays colored stripes.
5. Release the buttons.
6. Attach the USB-mini cable to the phone and the PC.
7. Take a cold beer :).
[I]Delay a few minutes, or alternativity take a short nap[/I]
8. Follow included instructions.
9. Read again.
...
10. Start playing with your device
I have also attached some technical guides together with mechanical/electrical repair manuals which includes assembly and disassembly hints, I really do hope the community finds them useful. If you are missing something, don't hesitate to PM me or you can mention in this thread what you really are looking for.
It is required that you've got a security unlocked phone (SuperCID with HardSPL) for being able to use the ROM images linked above!
Regards

thanks a lot

arash_ ! Thanx

awesome, thx for sharing with us

I tried UK IT SE versions, they all stoped at either 10% or 11%.
Now I cant use my phone anymore, it shows a four color screen(red green blue and white),
and says that
KOVS110
SPL-0.72.0000
MicroP1-787
MicroP2-707
Upgrade ROM code error
Please try again
Serial
--
I tried to use RUU to recover the process, but it didn't work, always stops at 10%
I am not an engineer, don't know much about it, could anymore one just tell me how to make my phone work again, I just want the SE system back, I am done with flashing the ROM. thanks

ffffdddd said:
I tried UK IT SE versions, they all stoped at either 10% or 11%.
Now I cant use my phone anymore, it shows a four color screen(red green blue and white),
and says that
KOVS110
SPL-0.72.0000
MicroP1-787
MicroP2-707
Upgrade ROM code error
Please try again
Serial
--
I tried to use RUU to recover the process, but it didn't work, always stops at 10%
I am not an engineer, don't know much about it, could anymore one just tell me how to make my phone work again, I just want the SE system back, I am done with flashing the ROM. thanks
Click to expand...
Click to collapse
the same problem here

any ideas how to unlock that cid?

Its a happy day again !!! Yipiii
1. Download mtty.exe
2. Disable activesync (connection settings -> uncheck "allow usb connections")
3. Connect your x1 to PC using USB cable.
4. Open mtty, select USB port and click OK.
5. Hit ENTER twice, you should see the "Cmd>" prompt.
6. Type the command "boot"
and its alive again but after restart need mtty to boot again.
so realy need to unlock cid to be god flashed

Very usefull thread. For CID unlocking need's HardSPL. arnisv, does this repair dead phones eg. stuck at tricolour (bootloader) screen ?

borce_razor said:
Very usefull thread. For CID unlocking need's HardSPL. arnisv, does this repair dead phones eg. stuck at tricolour (bootloader) screen ?
Click to expand...
Click to collapse
No, it doesn't work on my phone

ffffdddd said:
No, it doesn't work on my phone
Click to expand...
Click to collapse
Try this
Code:
MTTY (How to fix a bad ROM flash!) Hi,
I didn't see any post about using MTTY on Kaiser.
If I did a bad ROM flash with my previous device (HTC Universal), I could always fix this by clearing the FAT table with MTTY.
Believe me... if you flash and it stops ad 85% you will be very happy if you can use this tool!
Reason I started this thread is to help out people who are having such a problem with there Kaiser!
This is the correct procedure to get you out of trouble
1. Stop ActiveSync, by Task Manager (press Ctrl + Alt + Delete)
kill two processes rapimgr.exe and wcescomm.exe
2. put your device into the cradle
3. Run mtty and Choose WCEUSBSH001 in 'PORT' (if it doesn't show then you didn't stop all active sync processes above!)
4. type "set 16 0" without the quotes to tell bootloader to boot the OS after reset. (for some devices it can also be "set 14 0")
5. type "task 8" to get your device formatted
6. type "task 0" to ask your device reboot
7. take the device out of the cradle, and manually reset it if it does not do that already.
Incase of an emergency it could be very helpfull I think!
Thank you all for providing the input in this thread so I could make this small user manual!
Happy flashing!
Search for MTTY ver 1[1].42 or other, this is from our forum. It work's on Kaiser, maybe will work on xperia. And I'M NOT RESPONSIBLE FOR ANY DAMAGE DONE WITH THIS

Xperia HardSPL thread created

What rom is the swedish one? Newer or the same as it was delivered with?
Edit: Im new to windows mobile. What should i look for to check what version i have?

[email protected] said:
What build is the swedish on? Newer or the same as it was delivered with?
Click to expand...
Click to collapse
As i see it, it's the same as we allready have

borce_razor said:
Very usefull thread. For CID unlocking need's HardSPL. arnisv, does this repair dead phones eg. stuck at tricolour (bootloader) screen ?
Click to expand...
Click to collapse
no it just boots the phone in wm and all works exept can not restart the phone without myyt

If you turn off the phone it can't be booted again without mtty ?

borce_razor said:
If you turn off the phone it can't be booted again without mtty ?
Click to expand...
Click to collapse
yes need help of mtty

How its possible know which version have CID? All swedish version have CID but its able to unlock and after that u can flash to English OS?

ok after
Cmd>set 16 0
Cmd>task 14 0
now phone boots without mtty

borce_razor said:
Try this
Code:
MTTY (How to fix a bad ROM flash!) Hi,
I didn't see any post about using MTTY on Kaiser.
If I did a bad ROM flash with my previous device (HTC Universal), I could always fix this by clearing the FAT table with MTTY.
Believe me... if you flash and it stops ad 85% you will be very happy if you can use this tool!
Reason I started this thread is to help out people who are having such a problem with there Kaiser!
This is the correct procedure to get you out of trouble
1. Stop ActiveSync, by Task Manager (press Ctrl + Alt + Delete)
kill two processes rapimgr.exe and wcescomm.exe
2. put your device into the cradle
3. Run mtty and Choose WCEUSBSH001 in 'PORT' (if it doesn't show then you didn't stop all active sync processes above!)
4. type "set 16 0" without the quotes to tell bootloader to boot the OS after reset. (for some devices it can also be "set 14 0")
5. type "task 8" to get your device formatted
6. type "task 0" to ask your device reboot
7. take the device out of the cradle, and manually reset it if it does not do that already.
Incase of an emergency it could be very helpfull I think!
Thank you all for providing the input in this thread so I could make this small user manual!
Happy flashing!
Search for MTTY ver 1[1].42 or other, this is from our forum. It work's on Kaiser, maybe will work on xperia. And I'M NOT RESPONSIBLE FOR ANY DAMAGE DONE WITH THIS
Click to expand...
Click to collapse
Thanks a lot, my phone is working again, although its still in Swedish.