Database Users

ROMs and getting it onto the PPC

OK I have the tmo PPC its already got 2003 on it and I know the loader is 5.15, other info that might be needed.
ROM 4.01.16 ENG
Radio 6.25.02
OK I want to get my own cooked ROM onto this, I know I know use the SD card method, well I don't have one and after getting this thing can't get one for a while either. I have the cradle that it comes with and have put software into etc, I have tried some unlock ROM software to find it didn't work etc etc. after cooking ROM and running it it tells me in a DOS window:
Error getconntiontype - An Existing connecitonwas forcibly closed by the remote host.
error getting connectiontype
so basicly I need to find a way to get this into my PPC via activesync or something. sorry for bad post a little tired but I think people will understand and be able to help me or tell me I need SD card and wait until I get one.

I think you can use xdatools to flash the rom direct from xda memory, choose the nbf file as source then choose the xda device memory as destination from the drop down box in destination section.

OK tried that but can't access the PPC with xdatools so that won't work. thats for trying though.

TMO ROMs are known to resist exe flashing ... use the SD method and you are lucky to have the boo loader 5.15

Well glad to know that my boot loader is a good one, now to find a SD card I can borrow to do this with, should I use a 32 or 64 or does it really matter as long as it holds the file.

64 megabytes is needed really, I have had a problem with 32 meg, it looks like it is programmed but when i flash it there is always a problem.

macgyver33 talked about having a 2003 version. Can anyone tell me where to get it? I mean european one (900-1800 MHz). Or at least the PDA part of it? And yet haven't found quiet an exact explanation of "SD method" - any suggestions? Thanx a lot!

Bootloader v.5.17 locked
BL v.5.17 + TMO ROM. I am not able to downgrade the bootloader or change ROM.
I've tried using:
Cooked ROM.EXE - No way
(Error: GetConnectionType - An existing connection was forcibly closed by the remote host. Error getting connectiontype)
XDA OS Image Tool - No way
(Error: Same as above)
ITSTools - pnewbootloader - No way
(Error: Unable to find flash info offset, cannot disable bootloader writeprotect)
SD Method - No way
In bootloader mode (soft-reset while pressing on/off button), I have no options: Even with an SD card with OS image inside, there's no way to start ROM download as there is no option to choose...
Any idea?
Thx

Check this thread

Thanks Biso007.
No way. My XDA doesn't load the bootloader in a proper way:
1. Inserted th SD card in his slot
2. Answered "No" to format the card
3. Soft-reset while pressing on/off button (so to enter in bootloader mode)
4. Display turns off
5. No Wallaby Bootloader screen, so no action to take...
6. Wait... Nothing.
7. I've also tried to press the "Action" button so to start the SD downloading... Nothing
8. Wait... Nothing.
6. It needs another soft-reset to exit this state (a not working bootloader mode, I suppose)
7. It turns on "normally".
Any further idea? :-(
Thanks

if I'm not wrong, I couldn't see that you ran the 5.17 patch first ... without it your device will never detect the SD file ... chech the thread again

XDA 1 not working

Hi,
I was upgrading the software upgarde on my device. I successfully upgraded the Pocket PC software on the O2 XDA, but when I tried to upgrade the GSM radio/GPRS software of the O2 XDa, it gave some error and after this my device is not starting at all. The only mistake I did was that "I did not remove the SIM card before upgrading the GSM radio/GPRS software" The device does not start even after cold booting the same. When I start the device, the O2 screen comes and after a quite long time the main window does come but I cannot do anything. I tried to tap on contacts, time, tasks but nothing happens. I can see the windows logo wall paper but cannot do anything. Please help on how I can restore back my O2 as a cold reset also does not work. :?
Thanks and Regards
Jinesh

There's many topics about your question in the forum. Search it! Try to search with this keywords: 1% error, repair.zip

There's many topics about your question in the forum. Search it! Try to search with this keywords: 1% error, repair.zip

Hi,
I have tried all the available options but it still does not work. To restore the ROM how do I get access to the O2 cause niether serial nor USB is detecting it.
Please help.
regards
Jinesh

SD card install guide
Ok here you go, its a little outdated but its what I still use:
Qman's how to use XDArit to write nk.nb1 or nk.nbf to your SD card aka the Bootloader Method!
1. Place XDArit and the nk.nb1 or nk.nbf file in the same folder and start XDArit.
2. Select your SD card (disk drive) from the drop down menu.
3. Select Write to SD
Notice that the Windows CE box is already checked so just click the browse button at the end of that window.
4. Select your (nk.nb1 or nk.nbf) image and then Open
Notice by default XDArit will open looking for a *.nb1 file but if you're going to use a .nbf file you'll have to manually change the "Files of Type" to *.nbf
Notice that nk.nbo / nk.nbo was automatically added as your boot-loader and its check box is unchecked so leave it that way and click OK. XDArit should start writing to the card.
When XDArit has finished writing the image put the SD-card into the XDA and hold the power button and soft reset. You'll be taken to the below screen:
SD DOWNLOAD
Card Type:
CE OS & BOOT
Press action to Download
Or
Press REC to Exit
Press action to download and it will start the download/restore from the SD card.
Follow the on screen instructions once its "Completed" which will consist of a "Soft Boot/Reset".
Click to expand...
Click to collapse

Thanks Chief, I will try out and let you know.
regards
Jinesh

Hi Rudegar,
I tried the procedure given by you. I was able to write to the flash successfully. After writing to the flash it gave a message "Checksum OK, Please cold reboot to reset".
I did a cold reboot. After starting the O2, it showed the O2 logo screen and after quite a long time, it asked me wether I want to format the SD card or not. After that it took me to the default screen of XDA wher eit showed options like "Add today's date, Contacts, Schedule etc etc. but upon tapping any of the options the O2 behaves erratically. If I tap on today's date it takes me somewhere else. Inshort it does not work.
I again did a cold reboot and now the device is in its original position i.e not going after the O2 logo where it gets stuck up.
One thing I would like to mention is that all these activities have been done putting the O2 on the cardle only as the battery is totally discharged and the device turns on only after putting it on cradle. Even after the cold reboot it does not start unless I put it on the cradle whichis connected to the mains. Is it Ok with this or am I doing something wrong? The battery does not charge and hence I have to do it in this way.
Please suggest what wrong am I doing? Any suggestions from anyone will be welcome.
regards
Jinesh

Hi,
Someone posted the original O2 ROM on this site and I downloaded the same after which I was partially succesful in flashing the ROM and reviving my dead O2 back to half life. :roll:
I burned the ROM on
to my SD Card and flashed the ROM on to my O2. After
successfully flashing the ROM I rebooted the device.
The device now starts Windows but it takes atleast 15
minutes to start. I get the today screen. WHen I cick
on start the start menu appears after a delay of 10
seconds and all applications run normal, however all
this happens only on the Cradle only.
When I go into the Battery Settings it shows "Battery
Status Unknown".
Also none of the phone functions work. The SIM card is
not recognized and in device information it does
dispaly the "IMEI number" and the "Protocl Version"
I am only able to use inbuilt phone applications.
Is there some problem with my battery cause it is not
charging even on the cradle.
Device Information does not show Radio Version, Protocl Version & IMEI number at all.
Can anyone please help me?

hello all,
it means that your radio stack are dead. Currently, We don't have any real method to fix this problem. When the radio stack is error, you can not upgrade it or do anything to make it work. We can only upgrade or downgrade the radio stack if it works. Also if you try to upgrade the radio stack, we realy need to flash the chip using a speceial tool or need the sd card which build in radio stack with we can only flash in bootloaading mode. Howerver, in some case, we can fix it but .... I think it is just lucky or the xda error when battery problem.... in this case, just disconnect the battery few minutes and connect it again by pressing the battery hole.
Regards,
Hoanghon
p.s. I have dead xda. I killed it when I upgraded the RADIO STACK. Therefore, if you are really need to upgrade the radio stack, I recommend use the official upgrade for secuirity. or just upgrade the rom only.
Note:
To eliminating the error, you need to upgrade the rom or the radio stack, you need to check if the rom fix the radio stack or the stack you are trying to upgrade it fix the rom or not.(ie, Tmobile Rom have to use it radio stack built for Tmobile pocket pc...... I know that in some case when we mix between the radio stack and OS it works but I don't think it work propertly. Anyhow the mixing bettween radio stack and OS is very dangerous if it doesn't suppport then you have to reflash the radio stack or rom(the OS is Okay but the keep upgrading the radio stack may cause the radio stack killed)

WE NEED SERIAL CABLE FOR PDA ANY HELP PLS!!!
Hi Jineshd we
have the same problem and we are sure that the only way is to do SD uptade
and U said U have a serial cable to Yours device. With that we can be able to download flash gsm rom from working device and put it back via SD card to ours. Pls tell me where can I get a serial cable or some schema how to prepare it and I will try to repair ours dead pdas. Its our only chance
rgds
Lukasz

Hi,
Thanks all for the replies.
Can anyone tell me how doI repair the radio stack?
Regards
Jinesh

no way without having special RSU rom update on SD card and run it from bootloader or dissembling the device and reprograming GSM rom on special rom/bios programing socket. (Here on forum is user Cgigate from Toronto CA who can do it but I cant contact him)

Problems!!

If i want to upgrade my wallaby i get an error message in the communications procedure. I have downloaded my ROM from lumpy's kitchen and ive tried to upgrade it many times right now.
Can anyone give me an advise how i could hardflash the ROM of my device?

I think you get an communication error when trying to flash via ActiveSync.
You have to flash via bootloader....
http://wiki.xda-developers.com/index.php?pagename=Wallaby
Here you get furthe rinformation about how to do it....
HTH
Stefan

Nothing yet
Ive tried to Bootload te rom, but after the message "connect your USB now" the device does not react anymore.
I have tried to run the application rom but this says that active sync does not recognize a device.
What should i do next?
Thanks for the quick respond!!

Even if i make a bacup to SD this doesnt work. There no explaination how to hard flash the device! Can you give me an advise???

What have you done exatcly, and where is the problem?
It's not really clear for me.
For Flashing via SD-Card there is no USB connection necessary....
STefan

I have tried to flash with the bootloader. When i push on the on/off putton and do soft reset i see the question "connect to USB now". If i connect and i start the rom nothing happens.
Afterwards i have tried to put the rom on my SD card. I have tried to do this OSimagetools. The pc does recognize the SD card in my wallaby. I also dont have a cardreader.
Is there a way to flash my wallaby in the bootloader-mode with the USB connection?
What do i have to do for it?
Thanks

Strange.
You should see device displays a background that consists of four equally sized vertical bars, colored (from top to bottom) white, red, green and blue. On top of this, it says:
WALLABY
Bootloader
V5.14
WAIT
After a few seconds, the WAIT is replaced by GSM OK. Both messages are in the blue bar, but have a white background.
What do you get?
What is labeld on your rear sticker of the device? (modell) ?
Stefan

Its model: PW10A1
SN: HT220cc15300
PN: 99HJ00007-00
Step 1)I have seen the horizontal bars. And its version 5.18. Ive also seen the "GSM OK"- notification.
Step1a)If i connect it afterwards to my USB nothing happens. The computer does not recognize the Wallaby.
Step2) If i hold the On/Off button i get the message "Connect to USB now" If i do this, activesync does recognize my device and i cannot install the ROM.
Step3) after step 1 i press the contacts button and i see 6 ways to backup my rom or GSM. I have backedup my GSM and ROM to SD. But this has no use for me.
Greetz,

Ok. Now I see.....
First of all, you have an totaly unknown Bootloader (5.18) to me, so i hope all steps will work....
You require a SD-Card with >= 64 MB
XDATools ftp://[email protected]/Wallaby/Tools/XDATools.zip
Your downloaded ROM from my kitchen
step1) Boot your XDA up normal and connect via active sync (guest partnership is ok)
step2) Copy all your data of your sd-Card to your local PC otherwise all data on it will be gone
step3) Enter bootloader of your device by pressing On/Off and doing a softreset
step4) After the Message GSM OK press the Contact Button of your device
step5) Navigate with the pad to "CE+BOOT TO SD"
step6) Confirm this with the Action Key (Press the middle of the Navigate-Pad)
step7) After finishing enter again bootloader by holding On/Off and doing a soft reset
step8) Bootloader should tell you something tah OS is detected on your SD-Card
If No -> Problem
If Yes -> continue
step9) Boot your XDA up normal and connect via active sync (guest partnership is ok)
step10) Install XDATools on your PC
step11) in a dos -box (cmd) go to the directoy where osimagetool is located
step12) enter command: "osimagetool -r xdasdslot -w original.nbf"
step13) enter command: "osimagetool --register"
step14) extract the downloaded ROM using winzip
step15) Run osimagetool
step16) Select the nbf-file in the english-folder of the extracted lROM as source and XDASlot as destination
step17) After finishing enter again bootloader by holding On/Off and doing a soft reset
step18) Bootloader should tell you something tah OS is detected on your SD-Card
step19) Press Action Key to install the ROM
step20) After finishing do a hard reset
step21) Now your ROM should be installed on your device.
step22) Locate the created file original.nbf and compress it using winzip
step23) Upload the compressed file to ftp://xdaupload:[email protected]/Wallaby/Uploads
step24) Enjoy your new ROM
That should be alll .....
;-)
HTH
Stefan

Thanks, But when i extract the rom to a folder, OS Imagetools cannot find the nbf-file. There is no nbf-file in the extracter-rom-folder. I can only find an nb-file.
There is a file called "NK" which says that its an NBF-file(properties). The file is 32MB large. I have tried to select this file (step 16), but the file is not being recognized. Even if i change the extension of the filename. The OSimage does not support this file.
I Have tried this with 3 ROM's : 2003 SE, 2003 and 2002 neither of them contain the nbf-file in the english folder.
Do you have an advice? I think i am very close right now!!
Thanks,

I have sucseeded to install 2002, but 2003 SE wont be recognized. It says its an usupported file.
Has this anyting to do with the fact that i renamed the file? If so can you tell me how to change the file back??
I have downgraded my wallaby to PPC 2002 right now.
Thanks Lumpi!!

WM2003SE couls only be installed via Exe-File. It can not be flashed with the osimagetool.
Stefan

Stuck on bootloader menu after error upgrading ROM

Help,
Is there a way to get the OS and boot img for my o2 XDA to put on my SD card so i can recover it?
I'm stuck on the boot-loader screen (version 5.22) i can not use active sync as it comes up as unrecognized device, im at my wits end, i just want to get my phone working again. is there any place i can get the O2 ROM file from? or anything that can be done, or do i have a useless brick now?
i tried upgrading with the developers ROM using the auto install, it got to the "it will take 5 mins to upgrade" screen then active sync lost connection, there was nothing showing in the progress bar, when i tried to restart, active sync could not connect. now im stuck with the boot-loader menu after a soft reset.

Sorry for the double post,
Right sorted the problem out, got a cooked ROM from a different site as no link i clicked on here was still active.
I found out that if you Format the SD card to Fat32 when in bootloader it doesn't recognize the ROM, so a format to just FAT under windows XP sorted it out, and now I'm back up and running again, though now i cant get my phone unlocked to Vodafone as the XDAunlock returns "error getting code" message. here are my Device info
Rom version 3.17.03
Radio version 4.21.X1
Protcal version 32S54

problem resolved by updating the Radio stack to 6.24 (placing the files onto the device and upgrading from there) once that had done, i had no signal, so downgraded it back to 4.21 and now I'm fully functional

Where did you get the ROM?
I have a similar problem with an XDA which failed whilst being flashed via active sync and now will not start apart from via bootloader. Where did you get the ROM that you mention please?
Thanks
Geezer

use this ROM from http://www.romkitchen.de/ choose one that u will use to cook, PC2002 or WM2003/SE, (WM2003SE cannot use SD Card, only can use activesyn) then downgrade bootloader from v5.22 to v5.15,
using MMC (flash SD) continue to special rom 1.2, Go to the bootloader utilities. Hit Contacts button and you'll get the boot loader option stuff. If the bootloader utilities you get to right away takes you to a menu with things like Boot+CE-->SD then you don't have to worry about hitting the contacts button. You only need Contacts button if when you get to the bootloader screen you see nothing more than some nice colors, the bootloader version and "GSM OK" message.
Take the Boot+CE-->SD option to back everything up. This will take a few minutes.
Once it's done pull the SD out ofthe ppcpe and stick it into your SD card reader. Bring up XDArit and chose your removeable device.
If you have more than one MMC slot select the different ones until you get one that says 'Wallaby' in the hex codes at the bottom of the XDArit screen. You'll be writing out two files, the first is the NB0 file (which is the bootloader) and the second is the NB1 file (which is the OS or ROM). Name these something like original.nb0 and 1.
Wipe the SD card (format FAT). Stick the SD card back into the pda and soft reset, then cradle it.
Go to a DOS prompt and CD to where you put 'pnewbootflash_40116.exe.' Type 'pnewbootflash_40116 nbl515.nb0' to write the Wallaby 5.15 boot loader to the device. If when you downloaded the 5.15 bootloader you called it something else (like 'wallaby_boot_loader_V5.15.nb0' you should of course use that name instead!
The output looks like this:
D:\XDAtools\binaries>pnewbootloader_40116 bl515.nb0
Copying D:\XDAtools\binaries\itsutils.dll to WCE:\windows\itsutils.dll
in FindFlashInfoOffset
protection found at 8c0d60f8
result: 00000000 00000000
for the complete, read this web :
http://www.romkitchen.de/
http://www.romkitchen.de/tools/
http://www.romkitchen.de/tools/manual_unlock.htm
*read careffuly and try it, you can read my post, almost similiar problem but i can solve it by read one by one,hehehhe.. never give-up, ok ^_^V

any help with magician rom?

OK I found this thread and this is what I need to do but I don't follow any of this. what is the ROm image and how do I cook? I'm totally lost and My phone is wrecked or bricked as you say???

Htc 0300 in tri colour

I have a HTC ELF 0300 it is stucking in the tri colour screen with the following
IPL: 2.26.0002
SPL:2.28.0000
i have followed the advice i found on this forum of flashing the ROM but when i try the rom update utility it comes up with error 270 about the image also i tried the mtty process but it wont open the usb port
i tried flashing the SD Card but it then says "Invalid Certificate"
i'm a total loss and totally stuck..
any help appricated

Have you really read this sticky thread http://forum.xda-developers.com/showthread.php?t=406721 before flashing ?
Have you used "search" function with f.e. "stuck in bootloader" before posting ?
If not, please do and you'll find very useful solutions

i have read the theads over and over again and finally worked out mtty and worked out my phone is
elf0300
tmob050
it's still in tri colour mode yet i cant find a rom for it...
i tried the nbh file flashing to the memory card
but no luck....
heelllp

Do you know if you have Elf or Elfin?
It is essential for flashing original Rom Elf: http://forum.xda-developers.com/showpost.php?p=2045325&postcount=2
Elfin: http://forum.xda-developers.com/showpost.php?p=2045051&postcount=1

i haave an elf (p3450) well thats what it says on my box
i cant find the orginal rom for this and i'm totally stuck
any help is greatrully recived
also i have tried CID unlocking it so i can put custom roms on it but my computer wont active sync when the phone is connected through the USB port...

Also, what did you do to get your phone stuck in bootloader in the first place?

my brother did it to my phone before i'd even had chance to use it , and i don't know what he did.....sorry x

Try this and follow the instructions exactly http://forum.xda-developers.com/showthread.php?t=347700 and report pls

i tried this yesterday at first when i pressed enter i didnt get >cmd (which is what happening now)
then when i do get it eventually after many tries it sasys
cmd55 or something failed
and stays on 0% on a gray screen
sorry if i sound stupiud.

Ok
First you connect your device, then right click on active sync icon on your computer, chose connection settings and change according to the instructions then continue with mtty.exe

i have done this
when i press enter i dont get anything come up....
yesterday i managed to get it up though and just stayed gray screen at 0%

Try again a few times making sure you didn't overlook any detail.
I just found this http://forum.xda-developers.com/showpost.php?p=3395787&postcount=155 possibly mtty version doesn't work
2- Another possibility is unbricker rom http://forum.xda-developers.com/showthread.php?t=446242
3- gold card method (the links are dead so you should pm Dsixda)
Flash from the SD card:
ELF0IMG.nbh on a FAT32 filesystem, complete flash takes about 30 minutes, so check your battery or connect to charger before the flashing process starts.
1. Format microSD card from your computer.
2. Extract the .NBH file from your prefered ROM upgrade: In windows use winrar (right click) to extract the contents of the exe file. In Linux / MacOS use cabextract.
3. Rename the .NBH file to ELF0IMG.nbh and copy it to the root folder of your microSD card.
4. With microSD card inserted in the phone, start the bootloader (the bootloader is invoked by hold down the camera button and reset device with the stylus).
5. Confirm flashing on screen by pressing the power button (or the volume slider down).
6. Flashing might hang after some time but this is normal. Just wait.

Will try now and keep u updated
manny thanks x

Follow the instructions until you get cmd only, then return to the tutorial to continue
Good luck

Just an update
i downloaded the nbh file you sugested and tried both
1) flashing from the SD card by renaming file - when i do this is says checking sd contents then goes back to my bootlooder screen
2) running the romupdateutility.exe with the nbh file in the same folder it goes through then i get error 294 incorrect vender
i am unable to pm Dsixda about the gold card
i have no idea what else to try
ps: when running mtty i still get a gray screen then the bootloader screen.

Sorry to hear this, I'm out of ideas. Just some details not to miss:
try a hard reset
writing "ELF0IMG.nbh" (elf zero img and not elf o img)
google for mtty and download a few versions
Wait for an answer from Dsixda for gold card if you can't find your original rom

Creating your GoldCard
I don't remember well the procedure but you can try the following:
If you have access to a working pda or a working GPS device - PNA which is powered by WM (even modified) then you have to follow these steps:
Download this package and save it in your C:\ drive.
Run it.
(it will extract all the necessary files in C:\itsutilsbin (folder) and it will start the setup of Perl)
When the Perl - installation is finished run Perl Package Manager from Windows Start Menu.
Add repositories.
Name: itsme
Location: http://www.xs4all.nl/~itsme/projects/perl/ppm
Name: theoryx
Location: http://theoryx5.uwinnipeg.ca/ppms/package.xml
(HowTo: run Preferences from the Perl Package Manager menu and switch to the repository tab)
After database synchronization install these packages:
Crypt-DES
XdaDevelopers-NbfUtils
(HowTo: at the main window of Perl Package manager find those packages, mark them for install (the icon with green plus, next to the search bar) and run marked action(green arrow icon))
Format the sd card(FAT32) and insert it in a working pda.
Connect the working pda to the pc , wait to sync and run psdread.bat from C:\itsutilsbin.
Find an official rom from here with a ModelID which matches your device's one
Example: If your pda is an Elfin and you have ModelID ELF030000 then get the below rom from that thread.
RUU_Elfin_TMO_NL_2.26.114.52_4.1.13.52_03.08.90_BL UE_Ship.exe (T-MOBILE)
Device: ELF030000
CID: T-MOB003
Version: 2.26.114.3
Language: NLD
Click to expand...
Click to collapse
Extract the RUU_Signed.nbh, rename it to ELF0IMG.nbh and copy it to the sd card.
Fully charge your battery, insert the sd card to your pda, enter bootloader and flash from memory card
(Confirm flashing on screen by pressing the power button (or the volume down button)).
If everything went ok then you can use a HardSPL or a USPL to CID Unlock your phone and update the rom with one of your choice.
If you don't have a working pda use a card reader - Ubuntu (even from a LiveCD) and QMAT are required
Regards!

i don't have a working pda to use :-( the only pda i have is my bricked one :-(

buncie2010 said:
i don't have a working pda to use :-( the only pda i have is my bricked one :-(
Click to expand...
Click to collapse
There is a way to use a card reader instead.
Using Ubuntu LiveCD and QMAT
ps:I wonder how did the wiki entry got erased?
Dsixda and all the members who worked on this had done a great job and it's really annoying that all their work was lost.