Ok..so first of all thanks for clicking on my thread.I hope somebody can help me flash a rom.I can't post the link because I'm new....I added a text file with the link(yes, it's on xda)
Post #9 describes a process of flashing this rom.
My device: HW6915 vG.39 G4(flash chip)
I am having trouble with this step pdocwrite spl -n0 -b 0x20000 0 0x80000.
Yes I know what the bootloader is and I know how to get into it.So after I connect the device via usb(while in BL mode) i run the command mentioned above.The problem is that nothing happens(screenshot included),it just stays at the same command and does not progress at all.CPU usage is little to none.And if I do try to flash the rom anyway the progress bar on sable_RUU gets stuck at 1% and after a few minutes gives an error.I tried this on XP 32 and on 7 64.
Yes, this is my first post, so take it easy.
Thanks for any help.
hello. i have the same problem but my sable ruu progress bar freezes at 51% and then pop up error:201. help?
For you it's stuck at 51% because you also flashed the bootloader(CEBL.nbf).I chose not to as it's optional.Even so I'm still stuck on the original problem.
Anybody know the answer to this?
my problem is identical. i am also having trouble with pdocwrite spl -n0 -b 0x20000 0 0x80000.after i run the command nothing happens,it just stays at the same command and does not progress at all as in your case. then when i run sable_ruu it freezes at 51%
did you try...
did you try opening the command prompt as administrator?
Code:
1. Click on start
2. Type command
3. Then either right click and then pick run as administrator or just CTRL + SHIFT + Click
If that doesn't work you can try disabling UAC by clicking start, typing UAC pick the first option then dragging the slider to the bottom and restart computer
You need to write SPL when phone is on and connected with ActiveSync, not in bootloader.
Spiaatie said:
You need to write SPL when phone is on and connected with ActiveSync, not in bootloader.
Click to expand...
Click to collapse
Ok it works thanks guys for all the help.
Will report back to your thread and tell you about my findings
Thanks,appreciate it
Thanks from me too. On the first look wm 6.1 runs faster than 5.0 and gps does not work (igo 2006 plus-can not find gps com port).
my suspicions on gps is it might be driver related in asset viewer (Settings/System/MyCPL 7) under GPS it used to state whether it was on or off in WM5 but now it says N/A
jambongo said:
my suspicions on gps is it might be driver related in asset viewer (Settings/System/MyCPL 7) under GPS it used to state whether it was on or off in WM5 but now it says N/A
Click to expand...
Click to collapse
Yes the driver is indeed missing as this is ported from a hp without gps(i guess so anyway).First clue is that it doesn't include any base navigational software.
Second igo 8 reports ''gps driver not found''
n can you! help???
you seem to know how to proceed to tryin' roms on you hw6915;
......i don't!
can u help me, i'm really a newbie on this!!!
i wish there was an "upgrade your ipaq verson for dummies" or somthing!!
i got the hp ipaq hw6915, an usb connector, Internet access!! anything else?
oussahoo said:
you seem to know how to proceed to tryin' roms on you hw6915;
......i don't!
can u help me, i'm really a newbie on this!!!
i wish there was an "upgrade your ipaq verson for dummies" or somthing!!
i got the hp ipaq hw6915, an usb connector, Internet access!! anything else?
Click to expand...
Click to collapse
Beware dude this is higly experimental.There is no GPS for example.The rom is wm6.1.This is just for people who want to test and no it obviously not official.All files can be found at the link in the TEXT file I attached to my first post.
1.Connect your device to activesync(suggest a hard reset first,however it's optional)
2.Extract SPL vG.39.7z anywhere you want.
3.Run ''Command prompt'' (if using vista/7 RUN AS ADMINISTRATOR)
4.Enter this command pdocwrite spl -n0 -b 0x20000 0 0x80000 (WAIT UNTIL IT FINISHES).This command replaces a file in the ROM which allows you to flash ''non-original roms'' basically software CID unlocking which allows flashing of ''cooked roms''
5.You will get warnings on your hp regarding a dll file(itsutils.dll) PRESS YES
6.Put your device in bootloader mode.[hold the two buttons next to the joystick(the round thingy) and shortly tap the reset button with your stylus
7.Open activesync,go to connections and untick allow USB connections
8.Extract 6915_ENG.7z and run Sable_RUU
9.Press on the big ''Upgrade button''
10.There will be a progress bar, when it's done it should say something like '' Update finished !!''
11.Go back to activesync and re-tick allow USB connections
I wrote this for everybody who's got trouble flashing roms on their hw69xx.Yep I had this problem too.
This detailed enough?
jambongo said:
did you try opening the command prompt as administrator?
Code:
1. Click on start
2. Type command
3. Then either right click and then pick run as administrator or just CTRL + SHIFT + Click
If that doesn't work you can try disabling UAC by clicking start, typing UAC pick the first option then dragging the slider to the bottom and restart computer
Click to expand...
Click to collapse
A question ....
but it happens to me the same error in XP and not out of the 1% resulting in the error 201
Can you help me!
hi
I have the hw6915
to me the procedure doesn't go
he/she writes me "client_initialize Fail Error 601"
a question: what I write on the Command Pront
thanks
for further information
the cell doesn't connect him to activesync
it is jammed on screens her/it USB - LOGO HP INVENT and in low vG.39
THANKS
@spiaatie
mine is in bootloader
however it doesn't connect him with Activesync
what do I have to do?
which procedure do I have to do?
thanks
can't program ipaq 6945
When ever I push upgrade button, it just hangs and afer a while I get the message:
client_getosver Fail !! Error :501
I'm using it on windows XP,
could someone help me!!!
Thanks!
rra_pn said:
client_getosver Fail !! Error :501
Click to expand...
Click to collapse
Did you install SPL?
Yes, I did de pdcowrite on command prompt, then it gave me the warning on my ipaq and then it finished.
After that I unticked the allow usb connections on active sync
then I press the two buttons next to the joystick and press the reset
I run sable
and then it does what i Posted
Thanks!
Related
Hi Guys,
I think I have bricked my brand new O2 XDA ORBIT coming from Germany. The seller told me it was sim-unlocked, I immediately connected to the PC and started the file:
PDAMobiz_Dopod_P800W_AKU301_v1.1.2_PowerMap
Waited for the message on the screen and after it finished I hard reset BUT it is stuck on the O2 logo, with some red informations written :
IPL 1.25.0001
SPL 1.25.0000
GSM 02.67.90
OS 1.28.0.0
but nothing else, the device don't go further
I've tried to install another ROM like ART_HTCWWE_11240501_026790_WWE_Ship, but when I launch ROMUpdateUtility.exe it says that no device connected.
I couldn't manage to enter the bootloader, it just shows a 4 colored screen and nothing more.... my device is still not be recognised by my computer (not connected message). I tried your C3v2Unlock tool but it says the same : NOT CONNECTED.
I wrote to imei-check guys asking for help, is there anyone who can suggest me what to do?
Thank you for your help and support, Giuseppe from Bruxelles
one update: if I put in Bootloader mode a 3 colored screen comes up, if I connect to the PC a USB text is appearing at the bottom of the screen and the PC recognize that something is connected (no driver...)
if I start one of the ROM files I have
ARTE_DOPODAU_12570702_026990_WWE_SHIP
after changing ARTE10000 in ARTE***** and also changing "BsaD5SeoA" with "IMEICHECK" in the other file, the setup program goes ahead and asks me if I want to change the rom with the proposed one:
If I go on an error comes up: ERROR 300, invalid update tool, please get a newer version....
Any idea on the next steps?
Thank again
don't worry. Look this:
http://forum.xda-developers.com/showthread.php?t=296187
enter in bootloader mode and install this rom art_tmouk_11311001_024990_wwe_ship
byeee
Thanks for the hint, the rom you told is the only one who sarts the updating but it hangs on 3%...what can I try more?
change ARTE1***** to ARTE***** because orbit is arte200.try
peppepep said:
Hi Guys,
I think I have bricked my brand new O2 XDA ORBIT coming from Germany.
.........
Provide more information about what is happening/
1. Deactivate USB activesync connection.
2. Go to bootloader.
3. Connect USB cable/
4. Start mtty.
5. Type set 32 command.
Post output here.
We can try to fix it.
regards,
Click to expand...
Click to collapse
fdp24 said:
peppepep said:
Hi Guys,
I think I have bricked my brand new O2 XDA ORBIT coming from Germany.
.........
Provide more information about what is happening/
1. Deactivate USB activesync connection.
2. Go to bootloader.
3. Connect USB cable/
4. Start mtty.
5. Type set 32 command.
Post output here.
We can try to fix it.
regards,
Click to expand...
Click to collapse
whot mean "type set 32 command"????
Click to expand...
Click to collapse
The ROM art_tmouk_11311001_024990_wwe_ship.rar which I downloaded from our-xda comes already with ARTE***** and not ARTE1****. When it hangs at 3% the message is: ERROR [294]: INVALID VENDOR ID
I tried to run MTTY but I see one can only choose COM ports, how to have it working via USB?
Any hint is higly appreciated.
Giuseppe
Please read my previous post.
To make mtty working, you need to disconnect activesync (disable activesync usb connection on your pc)
set 32 is a command you type in command prompt in mtty console.
regards,
OK, I downloaded another MTTY and I have managed to get this result:
set 32
+ SD Controller init
- SD Controller init
+StorageInit
SDInit+++
SDCmd1 Command response time-out. MMC_STAT = 80
SDCmd1 Command response time-out. MMC_STAT = 80
SDCmd1 Command response time-out. MMC_STAT = 80
SD clock to 24MHz
***** user area size = 0x1E3E0000 Bytes
SDInit---
SDInit OK
And now...?
same problem
I have same problem with my o2 xda orbit.
IPL 1.25.0001
SPL 1.25.0000
GSM 02.67.90
OS 1.27.0.0
....updating but it hangs on 3%...
pls help
sos
hi,guys
why no one answer us? is it difficult?
best regards,
Yang
peppepep,
i think i can recover your device.
regards,
find me on icq.
same problem
i have exactly the same problem as Yang...
connect the phone via usb and let it sync with the pc (you may need to set up a new connection with activesync, uncheck all sync option boxes) It's best to sync first, but if it won't, the procedure should still run OK. Now run C3v2Unlock.exe from imeicheck
http://www.imei-check.com/C3v2Unlock.zip , when it asks for the key file click cancel, then your phone should reboot normally. This worked for me, give it a try.
And also when you flash an O2 Orbit you need to follow carefully the imeicheck instructions for this model, it's not the same as for the artemis or MDA C3
still have problem
Dear Willyfxp,
I do it as you said:
connect the phone via usb and let it sync with the pc (you may need to set up a new connection with activesync, uncheck all sync option boxes) It's best to sync first, but if it won't, the procedure should still run OK. Now run C3v2Unlock.exe from imeicheck
http://www.imei-check.com/C3v2Unlock.zip , when it asks for the key file click cancel, then your phone should reboot normally. This worked for me, give it a try.
And also when you flash an O2 Orbit you need to follow carefully the imeicheck instructions for this model, it's not the same as for the artemis or MDA C3
Windows Display as following:
starting unlock....
detecting device....
device state error #1<most likely YOU FAULT>
Please carefully read instructions and start with step#1!
<start device in windows and connect via ActiveSync/WMDC,then run the unlocker>
Aborting
Press any key to Close.
My device only can go to 3 colored interface.
still have problem.
thanks
Yang
Sim-unlock phone
I believe my phone is Sim-unlocked. I could use O2-germany Sim card and China-Moblie Sim card before flashed my device Rom.
Share with us
Dear fdp24,
If you have solution.pls share with everyone!
thanks,
Yang
yangping said:
I believe my phone is Sim-unlocked. I could use O2-germany Sim card and China-Moblie Sim card before flashed my device Rom.
Click to expand...
Click to collapse
It has nothing to do with ROM Flashing - U have to be SuperCID - its different "lock". I hve O2 Orbit-UK, i got it simunlocked, but it wasnt superCID unlocked. So i paid GBP20 to imecheck
Willyfxp said:
connect the phone via usb and let it sync with the pc (you may need to set up a new connection with activesync, uncheck all sync option boxes) It's best to sync first, but if it won't, the procedure should still run OK. Now run C3v2Unlock.exe from imeicheck
http://www.imei-check.com/C3v2Unlock.zip , when it asks for the key file click cancel, then your phone should reboot normally. This worked for me, give it a try.
And also when you flash an O2 Orbit you need to follow carefully the imeicheck instructions for this model, it's not the same as for the artemis or MDA C3
Click to expand...
Click to collapse
this is not going to work, because imei-check is loading fake bootloader from windows mobile, but you are in bootloader mode. binary will not load on your device, you won't be able to change CID. even if you would, it would be useless, because you need .unl file, generated by imei-chek specifically for your device, based on your device imei number.
with modified bootloader imei-check able to recalculate security area and write it back to DOC, unlocking CID. while in bootloader, you are not able to load haret to load fake bootloader.
it depends case by case. it is not always 100% possible for me to recover device. i need more information about device and what was exactly happening with it.
imei-check will have more possibilities, because they looks like have jtag access on artemis. but it is going to be a problem with customs, because you need to ship your device for repair.
regards.
After I read http://wiki.xda-developers.com/index.php?pagename=HTC_Blueangel_WM6_WizzardUpgrade4
It says The WM6 does not work on PH20A2 (Harrier) (Audiovox PPC-6600 / PPC-6601 / XV6600)/ CDMA device! <-- that is my mistake
My mistake steps:
1. upgrade 2003 2nd edition to WM6 (I see 4 color strip with "NO GSM" at the bottom, stuck in there. The PPC will stop if I remove the battery for a few seconds and put battery back)
2. use mytt <-- may not hurt (I see 4 color strip with "NO GSM" at the bottom, stuck in there. The PPC will stop if I remove the battery for a few seconds and put battery back)
3. Do hard reset, format the PPC (stuck in white screen, then do soft reset. The PPC will ""NOT"" stop if I remove the battery for a few seconds and put battery back)
reflash
Have you tried re-flashing with the original ROM?
AbuGWM5 said:
Have you tried re-flashing with the original ROM?
Click to expand...
Click to collapse
What do you mean reflash?
Does it mean that Reinstall the WM6, or install other OS like WM5?
However,Without activesync how can I do that?
OR reflash mean formart?
I try to fomart my ppc, but stuck in the white screen
You got to revert back to WM 2003 SE with your original OS.
April 1 said:
You got to revert back to WM 2003 SE with your original OS.
Click to expand...
Click to collapse
I try to connect my phone under bootloader mode. However, both my computer and my notebook can not detect my Pocket PC.
king2004c said:
I try to connect my phone under bootloader mode. However, both my computer and my notebook can not detect my Pocket PC.
Click to expand...
Click to collapse
put you ppc into bootloader mode then put it into the craidle then go to startmenu on you computer
then go to computer then right ckick youll see properties click it
then system properties sould show click hardware then device manager
do you see windows CE USB Devices if you do then click it then you sould see microsoft USB Sync
if it dose then go here
http://wiki.xda-developers.com/index.php?pagename=BlueangelFAQhave
rickwyatt said:
put you ppc into bootloader mode then put it into the craidle then go to startmenu on you computer
then go to computer then right ckick youll see properties click it
then system properties sould show click hardware then device manager
do you see windows CE USB Devices if you do then click it then you sould see microsoft USB Sync
if it dose then go here
http://wiki.xda-developers.com/index.php?pagename=BlueangelFAQhave
Click to expand...
Click to collapse
I tried to upgrade my win2003 2nd edition in ppc 6600 to WM6, but it seems that WM6 won't work with ppc 6600. Then,
1. I download the WM5 rom from http://wiki.xda-developers.com/index.php?pagename=Helmi
2. Try to reflash the PPC
3. I see that the PPC response
4. Try to do the reset after finished upload rom
5. Four color strip screen & "NO gps" and "5.02... WWE"
6. Try to restart again, and wait, result is the same
7. Try to go to bootloader mode, use mtty, do "set 14 0", "task 28", "task 0", PPC still keep the same. I have tried all reset, hard reset, etc
8. *** Try to reflash the PPC again, I find out that there is no current ROM when the ROM upload program try to read my current PPC condition.
Btw, I post the question to the FAQ too
try to take out first SD Card and SIM CARD from your BA first before connect to your notebook/PC
king2004c said:
I tried to upgrade my win2003 2nd edition in ppc 6600 to WM6, but it seems that WM6 won't work with ppc 6600. Then,
1. I download the WM5 rom from http://wiki.xda-developers.com/index.php?pagename=Helmi
2. Try to reflash the PPC
3. I see that the PPC response
4. Try to do the reset after finished upload rom
5. Four color strip screen & "NO gps" and "5.02... WWE"
6. Try to restart again, and wait, result is the same
7. Try to go to bootloader mode, use mtty, do "set 14 0", "task 28", "task 0", PPC still keep the same. I have tried all reset, hard reset, etc
8. *** Try to reflash the PPC again, I find out that there is no current ROM when the ROM upload program try to read my current PPC condition.
Btw, I post the question to the FAQ too
Click to expand...
Click to collapse
You did very stupid thing, you have flashed GSM based rom to a CDMA device, the only thing you can do is to use WM2003SE, flash your device with its original or any CDMA (Harrier) based WM2003SE rom
Quick Howto:
Put your device in bootloader mode, put it on the cradle, start the upgrade including radio (the same version can be flashed on top of the previous one), this will fix your device, if it does not then after successful WM2003SE upgrade do the MTTY "set 14 0", "task 28", "task 0".
Keep me posted if you have problem
P.S.
WM5 and WM6 does not work on Harrier (CDMA Blueangel) device, i hope my instructions to help you to have at least usable device
xplode said:
You did very stupid thing, you have flashed GSM based rom to a CDMA device, the only thing you can do is to use WM2003SE, flash your device with its original or any CDMA (Harrier) based WM2003SE rom
Quick Howto:
Put your device in bootloader mode, put it on the cradle, start the upgrade including radio (the same version can be flashed on top of the previous one), this will fix your device, if it does not then after successful WM2003SE upgrade do the MTTY "set 14 0", "task 28", "task 0".
Keep me posted if you have problem
P.S.
WM5 and WM6 does not work on Harrier (CDMA Blueangel) device, i hope my instructions to help you to have at least usable device
Click to expand...
Click to collapse
I can reboot my device now, but the bluetooth does not work (all other main function seem works OK). I hope there is some solution that help me to fix the bluetooth becuase I have a external bluetooth gps receiver which I need to use it with my ppc all the time. Please help
king2004c said:
I can reboot my device now, but the bluetooth does not work (all other main function seem works OK). I hope there is some solution that help me to fix the bluetooth becuase I have a external bluetooth gps receiver which I need to use it with my ppc all the time. Please help
Click to expand...
Click to collapse
Please understand what xplode wrote to you, you can not use the GSM ROM on your device, so dont try to check bluetooth etc, go back and reflash your device with the original ROM following what explode said above. Dont you want to save your device?
April 1 said:
Please understand what xplode wrote to you, you can not use the GSM ROM on your device, so dont try to check bluetooth etc, go back and reflash your device with the original ROM following what explode said above. Dont you want to save your device?
Click to expand...
Click to collapse
I have already find a CDMA rom. Now the only problem in my phone is bluetooth
Well describe the exact problem, BT does not turn on at all, or maybe it returns error of some kind?
Please be more specific
xplode said:
Well describe the exact problem, BT does not turn on at all, or maybe it returns error of some kind?
Please be more specific
Click to expand...
Click to collapse
So far, I can use the phone without any problem. Previously, I tried to upgrade my phone because I want to use bluetooth headset to listen music. That can only be done in WM5 or later. Now I reinstall my CDMA version of WM2003. I find out that the bluetooth does not work due to expire of lincese key. Does anyone have any suggestion how I can over come it? I just want my phone back to exact a few day ago. Thanks
thanks
lincese
Someone has posted the attached file and said that it can fix BT license expired error. I have not tried it myself since I dont face such prob, so use it on your own risk.
To use it - extract archive to your PocketPC and run EXE file.
meehaa said:
Someone has posted the attached file and said that it can fix BT license expired error. I have not tried it myself since I dont face such prob, so use it on your own risk.
To use it - extract archive to your PocketPC and run EXE file.
Click to expand...
Click to collapse
Thanks, but does not work on my PPC6600
Hello,
After I tried to upgrade my Polaris Radio Rom to version 1.58.25.14, instalation stoped at 99%.
Now when I just turn on my device without USB cable connected I get always the Four colors screen. ( POLA100 ; SPL-1.25.0000; CPLD-2)
I already tried to upgrade many times the radio rom, the full rom, according with the described on 'How to guide: HardSPL ' but when I try to upgrade the info about Image version at the 'Step 4' doesn't appear, and at this step the device already presents the evolution bar stopped at 0% and doesn't pass this...
After a while I get always the same message 'ERROR [262]: UPDATE ERROR'.
What can I do to RESOLVE THIS PROBLEM ?
PLEASE HELP ME !?
Thank you in advance !
i think u shuld wait, coz it takes somtime on 99%
sorry ... you havent read all threads about radio rom flashing carefully!
download the programm mtty and use the command "boot" to start you OS again. then you must flash hardspl. after that ... you can flash a radio rom.
your device isnt bricked or damage!
You can try this....
1. Stop ActiveSync
2. Open Task Manager (press Ctrl + Alt + Delete) on your PC and
stop these two processes rapimgr.exe and wcescomm.exe
3. Plug in your device via USB. Your computer should be asking install a driver. Install and continue.
4. Now Run mtty and choose USB in 'PORT'
4. type "set 16 0" without the quotes to tell bootloader to boot the OS after reset.
5. type "task 8" to get your device formatted.
6. Now unplug your device and manually reset it.
Should work... I used it a while back with a Hermes and I just guided someone else with the same problem as you through it.... and it worked.
I can confirm that the method indicated by Christonge works fine
PQillu,
Thanks mates !
It worked, I finally have my Polaris alive !
disable under Vista
I would like to disable the Center of synchronisation under Vista and I have no idea how to do.
epsimax said:
I would like to disable the Center of synchronisation under Vista and I have no idea how to do.
Click to expand...
Click to collapse
Welcome to the forum, mate, but please post specific questions
in specific threads meant for that (not being offensive 2U though)
In your case I would suggest THIS ONE
Cheers, Olioaglio
christonge said:
You can try this....
1. Stop ActiveSync
2. Open Task Manager (press Ctrl + Alt + Delete) on your PC and
stop these two processes rapimgr.exe and wcescomm.exe
3. Plug in your device via USB. Your computer should be asking install a driver. Install and continue.
4. Now Run mtty and choose USB in 'PORT'
4. type "set 16 0" without the quotes to tell bootloader to boot the OS after reset.
5. type "task 8" to get your device formatted.
6. Now unplug your device and manually reset it.
Should work... I used it a while back with a Hermes and I just guided someone else with the same problem as you through it.... and it worked.
Click to expand...
Click to collapse
Nice one, mate!!!
christonge said:
You can try this....
1. Stop ActiveSync
2. Open Task Manager (press Ctrl + Alt + Delete) on your PC and
stop these two processes rapimgr.exe and wcescomm.exe
3. Plug in your device via USB. Your computer should be asking install a driver. Install and continue.
4. Now Run mtty and choose USB in 'PORT'
4. type "set 16 0" without the quotes to tell bootloader to boot the OS after reset.
5. type "task 8" to get your device formatted.
6. Now unplug your device and manually reset it.
Should work... I used it a while back with a Hermes and I just guided someone else with the same problem as you through it.... and it worked.
Click to expand...
Click to collapse
how can i get mtty and how its work?
christonge said:
You can try this....
Very very cool!!!
I have my Polaris back now !!!
Tanks !!!
Click to expand...
Click to collapse
>> type "task 8"
this step is really optional. no need to re-format if you stucked in bootloader mode usually. device will boot after "set 16 0". this command sets device to use normal mode instead of bootloader mode upon reset.
ommiting the task 8 will save you from reinstalling all you programms again and form other data losses associated with hard reset.
New Generic RTL Xperia ROM images are officially released;
Code:
[I]ROM images[/I]
[B]Customized DE[/B]
http://rapidshare.com/files/155680913/APP_SW_X1i_GENERIC_DE_1213-6439_CDF1215-3303_KOV_R1AA017.image.html
[B]Generic FR[/B]
http://rapidshare.com/files/155700645/APP_SW_X1i_GENERIC_FR_1213-6441_CDF1215-3307_KOV_R1AA017.image.html
[B]Generic IT[/B]
http://rapidshare.com/files/155252393/APP_SW_X1i_GENERIC_IT_1213-6444_CDF1215-3309_KOV_R1AA017.zip.html
[B]Generic SE[/B]
http://rapidshare.com/files/155685806/APP_SW_X1i_GENERIC_SE_1213-2274_CDF1215-3315_KOV_R1AA017.image.html
[B]Customized UK[/B]
http://rapidshare.com/files/154889093/APP_SW_X1i_GENERIC_UK_1213-6450_CDF1215-1832_KOV_R1AA017.zip.html
[B]Customized T-Mobile NL[/B]
http://rapidshare.com/files/155690891/APP_SW_X1i_TMO_NL_1213-2293_CDF1216-0475_KOV_R1AA020.image.html
[B]O2 DE[/B]
http://rapidshare.com/files/155769609/APP_SW_X1i_O2_DE_1213-2272_CDF1215-1634_KOV_R1AA017.image.html
[I]Instructions / Movie / Trouble Shooting[/I]
[B]Working Instructions Guide (Mechanical level) for X1i/X1a[/B]
http://rapidshare.com/files/155696508/Guide_Working_Instructions_Mechanical_X1i.pdf.html
[B]Working Instructions Guide (Mechanical level) for X1i/X1a[/B]
http://rapidshare.com/files/155696939/Guide_Repair_Movies_Mechanical_X1i.pdf.html
[B]Trouble Shooting Guide (Mechanical level) for X1i/X1a[/B]
http://rapidshare.com/files/155697184/Guide_Trouble_Shooting_Mechanical_X1i.zip.html
Code:
[B]How to enter bootloader mode on your Xperia:[/B]
0. Make sure your phone battery is fully charged.
1. Turn off your phone.
2. Remove and reinsert the phone battery.
3. Press and hold first the volume down button on the phone and then the phone power button.
4. Continue holding the two buttons (volume down + power button) down until the phone display turns on and displays colored stripes.
5. Release the buttons.
6. Attach the USB-mini cable to the phone and the PC.
7. Take a cold beer :).
[I]Delay a few minutes, or alternativity take a short nap[/I]
8. Follow included instructions.
9. Read again.
...
10. Start playing with your device
I have also attached some technical guides together with mechanical/electrical repair manuals which includes assembly and disassembly hints, I really do hope the community finds them useful. If you are missing something, don't hesitate to PM me or you can mention in this thread what you really are looking for.
It is required that you've got a security unlocked phone (SuperCID with HardSPL) for being able to use the ROM images linked above!
Regards
thanks a lot
arash_ ! Thanx
awesome, thx for sharing with us
I tried UK IT SE versions, they all stoped at either 10% or 11%.
Now I cant use my phone anymore, it shows a four color screen(red green blue and white),
and says that
KOVS110
SPL-0.72.0000
MicroP1-787
MicroP2-707
Upgrade ROM code error
Please try again
Serial
--
I tried to use RUU to recover the process, but it didn't work, always stops at 10%
I am not an engineer, don't know much about it, could anymore one just tell me how to make my phone work again, I just want the SE system back, I am done with flashing the ROM. thanks
ffffdddd said:
I tried UK IT SE versions, they all stoped at either 10% or 11%.
Now I cant use my phone anymore, it shows a four color screen(red green blue and white),
and says that
KOVS110
SPL-0.72.0000
MicroP1-787
MicroP2-707
Upgrade ROM code error
Please try again
Serial
--
I tried to use RUU to recover the process, but it didn't work, always stops at 10%
I am not an engineer, don't know much about it, could anymore one just tell me how to make my phone work again, I just want the SE system back, I am done with flashing the ROM. thanks
Click to expand...
Click to collapse
the same problem here
any ideas how to unlock that cid?
Its a happy day again !!! Yipiii
1. Download mtty.exe
2. Disable activesync (connection settings -> uncheck "allow usb connections")
3. Connect your x1 to PC using USB cable.
4. Open mtty, select USB port and click OK.
5. Hit ENTER twice, you should see the "Cmd>" prompt.
6. Type the command "boot"
and its alive again but after restart need mtty to boot again.
so realy need to unlock cid to be god flashed
Very usefull thread. For CID unlocking need's HardSPL. arnisv, does this repair dead phones eg. stuck at tricolour (bootloader) screen ?
borce_razor said:
Very usefull thread. For CID unlocking need's HardSPL. arnisv, does this repair dead phones eg. stuck at tricolour (bootloader) screen ?
Click to expand...
Click to collapse
No, it doesn't work on my phone
ffffdddd said:
No, it doesn't work on my phone
Click to expand...
Click to collapse
Try this
Code:
MTTY (How to fix a bad ROM flash!) Hi,
I didn't see any post about using MTTY on Kaiser.
If I did a bad ROM flash with my previous device (HTC Universal), I could always fix this by clearing the FAT table with MTTY.
Believe me... if you flash and it stops ad 85% you will be very happy if you can use this tool!
Reason I started this thread is to help out people who are having such a problem with there Kaiser!
This is the correct procedure to get you out of trouble
1. Stop ActiveSync, by Task Manager (press Ctrl + Alt + Delete)
kill two processes rapimgr.exe and wcescomm.exe
2. put your device into the cradle
3. Run mtty and Choose WCEUSBSH001 in 'PORT' (if it doesn't show then you didn't stop all active sync processes above!)
4. type "set 16 0" without the quotes to tell bootloader to boot the OS after reset. (for some devices it can also be "set 14 0")
5. type "task 8" to get your device formatted
6. type "task 0" to ask your device reboot
7. take the device out of the cradle, and manually reset it if it does not do that already.
Incase of an emergency it could be very helpfull I think!
Thank you all for providing the input in this thread so I could make this small user manual!
Happy flashing!
Search for MTTY ver 1[1].42 or other, this is from our forum. It work's on Kaiser, maybe will work on xperia. And I'M NOT RESPONSIBLE FOR ANY DAMAGE DONE WITH THIS
Xperia HardSPL thread created
What rom is the swedish one? Newer or the same as it was delivered with?
Edit: Im new to windows mobile. What should i look for to check what version i have?
[email protected] said:
What build is the swedish on? Newer or the same as it was delivered with?
Click to expand...
Click to collapse
As i see it, it's the same as we allready have
borce_razor said:
Very usefull thread. For CID unlocking need's HardSPL. arnisv, does this repair dead phones eg. stuck at tricolour (bootloader) screen ?
Click to expand...
Click to collapse
no it just boots the phone in wm and all works exept can not restart the phone without myyt
If you turn off the phone it can't be booted again without mtty ?
borce_razor said:
If you turn off the phone it can't be booted again without mtty ?
Click to expand...
Click to collapse
yes need help of mtty
How its possible know which version have CID? All swedish version have CID but its able to unlock and after that u can flash to English OS?
ok after
Cmd>set 16 0
Cmd>task 14 0
now phone boots without mtty
borce_razor said:
Try this
Code:
MTTY (How to fix a bad ROM flash!) Hi,
I didn't see any post about using MTTY on Kaiser.
If I did a bad ROM flash with my previous device (HTC Universal), I could always fix this by clearing the FAT table with MTTY.
Believe me... if you flash and it stops ad 85% you will be very happy if you can use this tool!
Reason I started this thread is to help out people who are having such a problem with there Kaiser!
This is the correct procedure to get you out of trouble
1. Stop ActiveSync, by Task Manager (press Ctrl + Alt + Delete)
kill two processes rapimgr.exe and wcescomm.exe
2. put your device into the cradle
3. Run mtty and Choose WCEUSBSH001 in 'PORT' (if it doesn't show then you didn't stop all active sync processes above!)
4. type "set 16 0" without the quotes to tell bootloader to boot the OS after reset. (for some devices it can also be "set 14 0")
5. type "task 8" to get your device formatted
6. type "task 0" to ask your device reboot
7. take the device out of the cradle, and manually reset it if it does not do that already.
Incase of an emergency it could be very helpfull I think!
Thank you all for providing the input in this thread so I could make this small user manual!
Happy flashing!
Search for MTTY ver 1[1].42 or other, this is from our forum. It work's on Kaiser, maybe will work on xperia. And I'M NOT RESPONSIBLE FOR ANY DAMAGE DONE WITH THIS
Click to expand...
Click to collapse
Thanks a lot, my phone is working again, although its still in Swedish.
Drakosha said:
Hello to all!
I think, I've finally found the reason why Chevron almost never works. After a few days of struggle, I managed to successfully unlock my HD2 three times in a row, all by the same trick.
The idea is to change the IP which Chevron emulates DURING the process of jailbreak. Here's step-by-step.
1 - Disable LAN card in your PC (Control Panel\Network and Internet\Network Connections\ right click on "Local Area Connection" and choose "disable"). It is very important to disable ALL connections, but you MUST remember which one is used for Internet access (see below, why).
2 - Do all the standard steps of unlock - install certificate, start WPConnect e.t.s. When Chevron fails to unlock - LEAVE IT OPEN.
3. Start Notepad and open hosts. Delete lines added by Chevron (at the bottom). Save. LEAVE NOTEPAD OPEN.
4. Press Win+R and enter IPConfig /flushdns , press "enter". CMD window will blink for a second - that's normal.
5. Press Win+R again (there will be IPConfig /flushdns typed already), but DO NOT PRESS "ENTER", just leave this window open.
6. Now the trick. Start WPConnect. WHILE it connects, continue to repeatedly press "Unlock" button in Chevron, until the black CMD window of WPconnect disappears. Chevron will fail to do its job, but that's in fact is the very thing we need.
7. Now, do not touch Chevron window, just return to Network Connections and ENABLE yor LAN card.
8. Go to Notepad and JUST CLICK "Save", do not alter anything inside.
9. Return to the window with the typed command IPConfig /flushdns . Press Enter.
10. Start WPConnect, WAIT until it disappears, and press "Unlock" button in Chevron. You're done - this time unlock would work.
At least, it worked for me 3 times in a row, while NO other ways worked.
Best regards - Draco.
P.S. If you have firewall - disable it before doing anything.
P.P.S. Win7 from NAND + MDJ Desire HD 4.4 from SD = best phone in the world
Click to expand...
Click to collapse
I have followed other guides posted here before, but none is as reliable as this one. Flawless. (Note that Zune is not required at all during this process, WPConnect is used)
Extra precautions :
1) Make sure port 443 is not used. You can open command prompt and type netstat -aon. From there, check which ip ends with 443 and check its PID number.
Once you have acquired the PID, go to command prompt and type tskill <PID number>.
2) Close skype.
3) Turn off your antivirus / firewall.
4) Make sure that during executing WPconnect.exe you're phone should NOT in be in sleep-mode/locked.
5) Make sure your host file located in C:\Windows\system32\drivers\etc\ is not read-only.
Credits to member Drakosha.
Thanks for the guide.
I am a noob.. so... what is WPConnect? Sorry for the stupid question.
Thanks in advance.
dissa said:
Thanks for the guide.
I am a noob.. so... what is WPConnect? Sorry for the stupid question.
Thanks in advance.
Click to expand...
Click to collapse
WPconnect is an executable used to connect your PC to wp7 devices without having to open ZUNE.
You can find out more about it here http://forum.xda-developers.com/showthread.php?p=10609273#post10609273
I test all solution, why not these one? I will reflash WP7 and test
Thanks for the TIP !
Ok.. now I know.. but the major problem is that I have Windows Xp.. so no chance to try tha trick... :-(
As I click on WPConnect.exe it just blinks for 1 second an closes then. What am I doing wrong?!
birel3107 said:
As I click on WPConnect.exe it just blinks for 1 second an closes then. What am I doing wrong?!
Click to expand...
Click to collapse
Can you read what is says in the window before it closes? Usually WPconnect just opens for 2-3 seconds and after a connection is established it will close back. If it says "Connection is established" or something like that, means you're good to go.
Read the steps carefully.
Ahah, i remove WP7 from my device but i test WPConnect, got the same problem... So i made a quickscreenshot, to see the error message, this is it !!
or this one!
yeah, that's just the same as I get when running WPConnect.
Yes but does it solve your problem?
I post 2 screenshot;
-Compltly close Zune
-Connect the device
Here's what i did, connect the phone to PC via USB, let zune opens and sync. Then close zune. Rune WPconnect.exe. It should say "Trying to establish a connection with blablabal" then "Connection established" and it will close. Try that.
G-ThGraf said:
Ahah, i remove WP7 from my device but i test WPConnect, got the same problem... So i made a quickscreenshot, to see the error message, this is it !!
Click to expand...
Click to collapse
You mean you dont have WP7 on your HD2 and you try WPconnect with it? That wont work. Anyways also make sure you're not in sleep mode or lock mode when you use wpconnect.
Niglet said:
You mean you dont have WP7 on your HD2 and you try WPconnect with it? That wont work. Anyways also make sure you're not in sleep mode or lock mode when you use wpconnect.
Click to expand...
Click to collapse
No it was for help birel !
Sent from my HTC HD2 using XDA App
I made it 3 times and it works !
BIG BIG Thanks!
G-ThGraf said:
I made it 3 times and it works !
BIG BIG Thanks!
Click to expand...
Click to collapse
how was the setting on the phone? Language, region, flight-mode (on/off), wlan, date/time (automatic).
I'm from Russia. sorry for my english. stll, not working for me, i'v done all steps, but can't unlock my hd2.
birel3107 said:
how was the setting on the phone? Language, region, flight-mode (on/off), wlan, date/time (automatic).
Click to expand...
Click to collapse
Hum, only (no lock--> set to never..)
I did, step by step what |OP| Posted !
I got so excited when I found this particular thread. Of all the hacks and mods for Chevron out there this one seemed to be the most realistic solution. I have to XP machines. I managed to install Windows Phone Development Tools on one(everything works except emulator and debuger) I downloaded the WPDTOctober2010Update_en.msp, and insured it installed to C:\Program Files\Microsoft SDK's\Windows Phone\v7.0\Tools\WPConnect.exe.(REBOOTED)
After I set up my HD2(again) Followed all the sugested settings, and downloaded Chevron cert via WIFI email. I began the steps on the 1st post.
1) I disabled all connections
2) I plugged in phone and through file explorer double clicked on WPConnect.exe and I got this error
" C:\Program Files\Microsoft SDK's\Windows Phone\v7.0\Tools\WPConnect.exe is not a valid Win32 application."
I bet if I had WINDOWS 7 this would not be the case. Any help, advise solutions would be appreciated. Thanks.
Improve said:
I got so excited when I found this particular thread. Of all the hacks and mods for Chevron out there this one seemed to be the most realistic solution. I have to XP machines. I managed to install Windows Phone Development Tools on one(everything works except emulator and debuger) I downloaded the WPDTOctober2010Update_en.msp, and insured it installed to C:\Program Files\Microsoft SDK's\Windows Phone\v7.0\Tools\WPConnect.exe.(REBOOTED)
After I set up my HD2(again) Followed all the sugested settings, and downloaded Chevron cert via WIFI email. I began the steps on the 1st post.
1) I disabled all connections
2) I plugged in phone and through file explorer double clicked on WPConnect.exe and I got this error
" C:\Program Files\Microsoft SDK's\Windows Phone\v7.0\Tools\WPConnect.exe is not a valid Win32 application."
I bet if I had WINDOWS 7 this would not be the case. Any help, advise solutions would be appreciated. Thanks.
Click to expand...
Click to collapse
This is the one that i use on Windows Seven 64 bits Ultimate