Database Users

It's dead!

My battery went flat and I can't find my mains charger, so I connected it to my laptop using the usb cable, with the intention of recharging it. But it doesn't seem to be charging and I can't turn it on at all. Is that normal? Will it only recharge from a mains charger when the battery's dead? Finally, is it safe to by any odd charger off ebay etc.?

I do not know if that is normal or not. However with regards to charging, I have used a Motorola charger with USB connection successfully in the car and from the mains.

If it is all the way dead, you have to charge with original charger. USB charge will not work. Nor will a Motorola charger work. I think that as long as the charger is 5volts, you should be okay. My Motorola charger is like 3v or something.

Thanks

I had the same problem. It does not charge in the beginning, however, if you leave it connected to USB, it will start charging in an hour or so. damn long, but it's better than nothing...

Tried to keep it connected via usb for a few hours, no luck, guess I'll just have to wait till I've bought another mains charger. There seem to be plenty of cheaper ones on ebay etc., is it safe to buy any usb charger?

This happened to me, and I nearly had a heart-attack until I came to these forums for a solution. Apparently, the phone has to be on for the charger (mains or usb) to actually charge the phone. This is because the operating system of the phone controls the charging of the phone. If the battery is completely dead, the operating system cannot control the charging, and so no matter what kind of charger you use, and no matter how long you leave it plugged in, you won't be able to charge the battery.
The only way to get it to work is to get a bit of charge into the battery directly - not through the phone. In other words, you need to jump start the battery (almost like you would jump start a car's battery). What I did was take the battery to a phone repair shop, and asked them to boost the battery using boosting equipment. Their battery testing equipment will be able to tell you when there's sufficient charge to get it going. Then turn on the phone and plug in the charger immediately once it's booted up (in other words, when the operating system can kick in and start controlling the charging process).
Hope this helps.
PS, there's a post on this forum somewhere on how to do-it-yourself, but in the long run, I found my way to be the easier way.
PPS. Once your phone is back up and running, never let the battery run down completely.

Same happens to Motorola V3.
It is ridiculous design flaw.

This is really annoying, I was hoping to sort this out with a new charger (in the post now) but looks like I'm going to have to go to a t-mobile shop. Will they definitely have something to charge the battery a bit, or should I start looking into buying something to charge the battery at home?

Yes you need the main charger.
I was using my other phones charger(motorola) with my cingular 8125 and battery is completly empty it doesn't charge it.
Didn't wait for a hour but if that works.It's good i love my wizard

motorola V3 chargers do work. used the missus' when battery ws completely dead. interestingly, doesnt work the other way around...... :?:

help with my dead battery
Bdcol
Could you direct me to that post on how to charge a dead battery - I have searched but can't find it. This is a really annoying problem - does anyone know of a commercially available battery charger which doesn't need the phone OS (the battery looks pretty standard to me).
Many thanks
Chris

Help Wanted Got ablack screen !!!

Is there a wizard who can find a solution for my wizard !! I bought it one week ago now i have got black screen with no ability to turn the phone on and also no ability to soft or hard reset everything is dead and there s no battery charge ability. Any solution to slve it Please HELP ME !!!

Are you trying to charge the battery from the computers usb (or a 3'rd party usb wall adapter?) if so, this will not charge a completely dead battery. Try plugging it in to the usb wall charger that came with the device. This may help to charge the battery. Let me know if it works, or if you have any other questions....

You may need external charging
Charging of these batteries is controled by in-built circuit, so when it is discharged extremely low, it is very difficult to start charging.
Try leaving on charge for several hours or days and see if it starts charging. If it fails and you have no option to return it or buy replacement immediately, you may try to locate the polarity and use an external charger of same spec as reccommended for a few minutes and then continue charging in the wizard.
Someone did it here on the forum. You may want to search :roll:
Victor

Repair a Hermes

All,
I'm looking for a company which is able to clean and repair my HERM300 device.
It got wet and now when I want to charge it the led turns red.....
When I leave my device on a warm radiator it works and I can use the device...
But it seems to fail when it gets colder....
Any suggestions?
Cheers and thanks,
Hellejoep

hellejoep said:
All,
I'm looking for a company which is able to clean and repair my HERM300 device.
It got wet and now when I want to charge it the led turns red.....
When I leave my device on a warm radiator it works and I can use the device...
But it seems to fail when it gets colder....
Any suggestions?
Cheers and thanks,
Hellejoep
Click to expand...
Click to collapse
Can you say a bit more on "fail when it gets colder...."
I ask because soon maybe tonight I'm going to make a post on the charging and Red light problem but I'm just wondering exactly what you mean by "fail"
Cheers
Mike

mikechannon said:
Can you say a bit more on "fail when it gets colder...."
I ask because soon maybe tonight I'm going to make a post on the charging and Red light problem but I'm just wondering exactly what you mean by "fail"
Cheers
Mike
Click to expand...
Click to collapse
It blacks out as soon as I connect it to my activesync via USB....
Is it a short circuit?
Or something else?
Cheers,
Hellejoep

mikechannon said:
Can you say a bit more on "fail when it gets colder...."
I ask because soon maybe tonight I'm going to make a post on the charging and Red light problem but I'm just wondering exactly what you mean by "fail"
Cheers
Mike
Click to expand...
Click to collapse
I would like to add something, may be you already know, to red led knowledge. I have a car charger (just plain chinese USB charger with usb cable) When I connect my HERMES I could have 3 conditions: orange (charging) Nothing (not charging) or RED (?). If I soft reset, with charger connected, I ALWAYS have orange, after Windows Mobile screen, But if I disconnect and reconect I have ALWAYS No Light

connecting hermes to charger without battery also enables red light.

Charging Problems - Red Light of Death (RLOD)
Battery Charging Problems, in particular the RLOD so called because the phone refuses to charge and the red LED shows, indicating that the battery is NOT charging.
Background
Problems with charging are not HTC or Windows Mobile specific. Similar if not identical problems are reported across many models and platforms. The issues centre around the state of charge of the battery and the interpretive circuitry in the device and charger. Typically a device will show a Red light rather than an Amber charging light. (NB: RED LED always shows when battery is absent or fails to charge). see also http://forum.xda-developers.com/showpost.php?p=1076879&postcount=28
Getting the battery to start charging once this light is shown is not always straightforward and is as unpredictable and temperamental as priming a water pump (those that have done this will know what is meant). In other words, and to put it crudely, you need to kick start the system. Unfortunately those that have managed to do this have usually tried lots of things before it starts working again. This makes it hard to be absolutely certain about the solution other than perhaps the last 4 or 5 actions taken.
Those that have managed to recommence charging have not reported that the problem recurs on a frequent basis. (possible exception of in-car charging issue). This issue requires patience and time, (time maybe critical, it is possible the issue would resolve itself perhaps as charges dissipate within battery and circuitry involved). However the following points seem probable solutions and were thought to work by some who resolved the problem.
Failure to Charge (Red LED Lit when charger connected)
Causes of this problem are unclear, but in practical terms events leading up to this issue have included:
1
Leaving the phone on charge overnight (possibly but not necessarily with certain programmes or connections running) It seems a fault occurs in the charging system, which causes the battery charge to drain rather than increase. Resulting battery charge is very low. (Another Blog will be added concerning an Active Sync issue which can cause the battery to drain over-night through repeated connection attempts)
2
Through heavy use or not re-charging often enough so that the battery is permitted to reach a sub 10% charge (not precisely known but likely to be very low)
Possible Solutions:
A
1.) Remove battery
2.) Connect the phone to the charger or USB
3.) Insert the battery while connected to charger
4.) Red light should turn Amber
5.) Soft Reset
If this does not work immediately it is suggested that the battery be removed from the phone for around 1 hour and the above steps repeated.
OR
B
It has been found with some phones charging can be re-started by:
1 ) Remove battery
2 ) Connect charger (Optional. I would try this potential solution without the charger connected the first time I try this. If it fails to work then I would repeat the steps with the charger connected)
3 ) Holding the battery, line it up wiith the phone's battery contacts.
4 ) Move the battery rapidly on and off the contacts
6 ) Repeat the above until the Amber charging light comes on. So after perhaps connecting/disconnecting 20 times, insert the battery properly and give it a few seconds to see if the LED turns Amber.
7.) Soft Reset
NB: I have seen two reports where those attempting this report a fairly loud "pop" sound following which the phone began to charge. However in one case the person reported that they then had subsequent problems of signal reception on the phone and thought the popping sound may have been related to this.
OR
C
If your problems remain after trying this a few times you could always try the following to manually charge the battery a little (enough to let the phone charger circuit detect the battery is present when you put it back in)
1) Remove the battery from the phone!
2) Take 3 fresh AAA batteries in series (total 3 x 1.5V = 4.5V)
3) Connected the (+) wire to (+) on the battery
4) Connected the (-) wire to (-) on the battery
5) Hold this in place for 60 seconds.(possibly longer you are trying to charge it enough for charging circuitry to recognise there is a battery installed.
6) Put the battery in your phone
7) Switch on phone and start charging (via USB)
Hopefully you will get the Amber charging light.It may be worth repeating this a few times if not successful on the first try.
The electrical contacts are all important, poor contacts will render this a worthless exercise.
I leave it to you to decide how you connect the wires. If you have no other means you could enlist the help of someone to hold the batteries and wires together while you connect to the phone battery! Warning - Do not connect a mains based transformer to the battery with an incorrect charge rate (mAh) and voltage (V). Any attempt to force charge using mains transformers could be extremely hazardous (explosive). Only a qualified/competent person should attempt to charge the battery in this way. Similarly, even if you are using batteries to do this task, do not leave them connected for more than a few minutes and stop immediately if either set of batteries become warm.If the problem persists:The final resort - a new battery.
Mike
╤

Very good article Mike, I linked it on the Hermes problems wiki page

i just want to add my 2 cents to this, there was an earlier post on here that mentioned the car charger deal where it wont charge unless you turn the phone off, plug it in, then turn the phone.. right now i am on my 2nd 8525 and it has done this, but its not only the car charger (cheap belkin car charger) but it sometimes does this with usb cradle i got from ebay, i have opened the cradle and there isnt anything different, its a straight usb connection, hmm except now that i think about it there is a blue LED, but it shouldnt be drawing enough current to cause this. Also i have a motorola charger in my office that i used with my wizard (i believe output is slightly different, if i remember correctly its a .5 amp where as the HTC charger is 1 amp) but it also behaves in the same manner... the only 2 methods that work constantly and consistantly of plugging in without turning off is either the factory charger, or a regular usb cable on the pc..
just seems weird since all of these problematic situations worked fine on the wizard and i believe they both have the power requirements...
let me toss another idea in the fire here on this, something that just occured to me... i wonder if this somehow could be related to the factory installed driver for this. what made me think of this is how the battery meter only goes by 10%.. could this funky driver be the source of the problem?

shogunmark said:
right now i am on my 2nd 8525 and it has done this, but its not only the car charger (cheap belkin car charger) but it sometimes does this with usb cradle i got from ebay
Click to expand...
Click to collapse
If your cradle is not connected to your PC, or if your PC is off while you see the behaviour you described, then the likely reason is that pin 4 of the Mini USB connector isn't grounded on both your car charger and cradle. See here for more details.
Cheers
Daniel

pof said:
Very good article Mike, I linked it on the Hermes problems wiki page
Click to expand...
Click to collapse
Cheers pof.
Some of the type sizes are a bit strange (but readable!) serves me right for copying and pasting from Word formatting!
Tadzio's link is good/informative and I edited in a link to it in my post - though it's on this page anyway.
Mike

tadzio said:
If your cradle is not connected to your PC, or if your PC is off while you see the behaviour you described, then the likely reason is that pin 4 of the Mini USB connector isn't grounded on both your car charger and cradle. See here for more details.
Cheers
Daniel
Click to expand...
Click to collapse
cradle is connected to pc at all times, and i will deal with the car charger for now cause my HTC one should be arriving any week now, but thanks for the tip!

8525 (hermes) Charging may be voltage sensitive
I have noticed with my new 8525 (USA Cingular model of phone) that it came with a 5.5V charger. Whenever I connect to a 5.0 V USB source charging the phone is very "iffy". Given that the standard for USB is 5.0 V (4.75 - 5.25) there is a problem with the design. My question for the HTC crowd is can this be fixed via a ROM change or are we stuck with a bad design?

hellejoep said:
All,
I'm looking for a company which is able to clean and repair my HERM300 device.
It got wet and now when I want to charge it the led turns red.....
When I leave my device on a warm radiator it works and I can use the device...
But it seems to fail when it gets colder....
Any suggestions?
Cheers and thanks,
Hellejoep
Click to expand...
Click to collapse
http://www.america.htc.com/support/service-repairs.html
Since you got it wet, it is most likely not covered by the warranty, these and the numbers for out of warranty repair if you live in the U.S. I know that for cingular, you have to ship it to them yourself, and they will charge you a $28 diagnostic fee, before telling you how much is costs to fix the problem (if they even can)

heh here almost the same, providers are charging ~$29.5 USD as diagnostic fee but they are more polite, they first tell estimated costs, and only ask for the sum if you (usually) don't order the repair but need back your phone
Hellejoep:
if you are willing to send it abroad (inside EU) and you are either not need "overnight return" or such nonsense or cover the extra costs such operations really need, you may contact me. no diagnostics fee or anything such (though you will have a small loss.
about the charging problem:
the same issue occurs also in Wizard/Prophet, and Charmer (compactII) as well. though not in Magician, even so that they share the exactly same battery.
I believe it must have something to do with the charging controller. I don't have a disassembled unit at home with me now, but I suppose it should be a crap companion chip from Texas, to be interfaced with the ever-worst TI OMAP platform
(sorry, no hard feelings, pals, but someone using such one as an actual everyday phone must have some sorta mental problem )

strange battery issue
Hi all,
I've a similar issue with any charger.
It happened first with car charger (one cradle with an usb output): sometimes it charged, most of all it charged only when power was off.
Now I cannot charge with any method. (those described here: battery charging problems)
Usb cable (it's not original), original power supply, even with the y cable.
When i try to charge, it drain battery (i tried with a new one) and amber led blinks slowly instead to be firmly light.
There's anything I can do?
It's a SPV M3100 buyed two months ago on ebay.
I tried also with two roms WM6 official release ITA ver and Schap's 3.54b ITA ROM WM6
radio 1.48
Any suggestions?

Herm200/tytn problems
hi to all,
i read most of your post on possible problems with this PDA (HERM200/HTC TYTN).
i'll try to spent some few words to explain the story around my pda.
i live in italy and i bought the TYTN on december 2006 and for 6 months with his software problems i used it day by day in my business activity, untill one day, it falled down the ground from my and with all the leather cover (bundled with the pda, an hard black belt cover); then i took it and picked up a telephone number from my addres book and then putted it in charge for all the night; when, late in the morning, i took it, i noted that there was still the red light of the battery indicator and then PDA didn't turned on.
i tried to make soft/hard reset but nothing.
I carried to the italian warranty service of HTC and after 7 days they deliver to me the PDA in the same state that i carried; on the technical report there was: pcb damaged, battery connector pinouts damaged, pda not Repairable - out of warranty.
i thought: "i have had a lot of care for this PDA that still look like as new one"
and now i have a 700€ of unusefull PDA.
Last day i finally decided to open my PDA to find broken pieces and more.... but nothing.... i observed really well: NOTHING of wrong.
Now i will to know if somebody of you, can suggest me something to revive my PDA or suggest me any service center (affidable) in europe (not like the italian one) where to send it for maintenance: I DONT WANT TO THROW OUT MY PDA!
Thank you in advance for your attention and patience.
ps: sorry for my english, i hope it will be comprehensive.

therock-htc said:
Now i will to know if somebody of you, can suggest me something to revive my PDA or suggest me any service center (affidable) in europe (not like the italian one) where to send it for maintenance: I DONT WANT TO THROW OUT MY PDA!
Click to expand...
Click to collapse
If I understood you correctly, your TyTN still works - it just cannot charge the battery, right?
Then, probably one of the cheapest (although not perfect) solutions is to get a cradle that can charge a battery outside the TyTN (like this one on eBay). You will have to power down your TyTN, remove the battery and put it in the cradle every other night or so, so it's not very convenient. But it's cheap. Maybe you'll want to keep this as "plan B" in your mind while you look for a more perfect solution.
Cheers
tadzio

elehcimo said:
Hi all,
I've a similar issue with any charger.
It happened first with car charger (one cradle with an usb output): sometimes it charged, most of all it charged only when power was off.
Now I cannot charge with any method. (those described here: battery charging problems)
Usb cable (it's not original), original power supply, even with the y cable.
When i try to charge, it drain battery (i tried with a new one) and amber led blinks slowly instead to be firmly light.
There's anything I can do?
It's a SPV M3100 buyed two months ago on ebay.
I tried also with two roms WM6 official release ITA ver and Schap's 3.54b ITA ROM WM6
radio 1.48
Any suggestions?
Click to expand...
Click to collapse
Hello!
I had also a battery charging problems with my MDA Vario II (TyTN; Hermes; HERM300):
1. Charging from the AC mains supply with the original miniUSB 5V charger: no problems.
2. Charging in the car with the non-original car lighter miniUSB 5V charger: it was charged only when the phone was OFF; no charging when the phone was ON.
3. Charging with the USB-miniUSB 5V cable connected to the notebook: it is charging only when the phone is OFF; no charging when the phone is ON.
So I asked myself: what is the difference between all these three cases? They are all miniUSB 5V power sources... And I found out an answer: It should be a matter of the USB current amperage.
Original AC miniUSB 5V charger delivered with the phone is 5V/ 1A. When I have bought the car 5V miniUSB charger with the 1A (one amper) amperage - there is no problem with car battery charging anymore... ;-) The phone is charged either way: ON or OFF.
But is it possible to charge the battery correctly from the notebook? I think not, because I have no influence on the current value from the 5V notebook USB.
Previously I had MDA Vario (Wizard): in this phone there were no battery charging problems... I wonder why the are some with the Hermes...
Take care,
Przemo

Przemo_55 said:
And I found out an answer: It should be a matter of the USB current amperage.
Click to expand...
Click to collapse
This is not correct. The problem is well understood and has been discussed several times.
The key is that your device tries to sense what it is connected to:
- if there is USB data traffic, it concludes that it is connected to a computer. It will then negotiate the current (power) it can draw from the USB port with that computer.
- otherwise, your device checks if pin 4 of the connector is pulled to ground. If yes, it concludes that is is connected to a dedicated USB charger, and starts charging, consuming as much power as it needs. This mechanism seems to work only if the device is on - and sometimes not even then (bug?). I guess the mechanism is implemented in software, so it can't function when it is off.
- otherwise, it doesn't know what it's connected to. Could be a computer in stand-by that didn't power off its USB ports or something. Your device concludes it may be unwise to start charging (could, for example, drain the other device's battery).
The cheap after-market chargers do not connect pin 4 to ground (pin 5), so your device doesn't charge. If you are really good with a soldering iron, try connecting pins 4 and 5 of the charger's USB connector, and you'll see that your device will start charging with it.
Cheers
tadzio

tadzio said:
If I understood you correctly, your TyTN still works - it just cannot charge the battery, right?
Then, probably one of the cheapest (although not perfect) solutions is to get a cradle that can charge a battery outside the TyTN (like this one on eBay). You will have to power down your TyTN, remove the battery and put it in the cradle every other night or so, so it's not very convenient. But it's cheap. Maybe you'll want to keep this as "plan B" in your mind while you look for a more perfect solution.
Cheers
tadzio
Click to expand...
Click to collapse
Thank youu Tadzio,
but my PDA is DEAD !
I still don't try to charge the battery separetly.
The reason is that when i carried the PDA to service i leaved the PDA and Battery: i dont wanto to believe that service dont check the battery !??!?
However , i will try to charge the battery separetly and then i will know you the outcome.
Thanx and Cheers
Therock-htc

Battery Charging Problem

If I let the battery on my Wizard run down completely, I can't get it to recharge, either with a wall charger or USB charge/sync cable. I have to replace the battery. Is there a way to jump-start the charging process?
After I put in the new battery I can't even get the Wizard to boot up. I have to reflash with the provider ROM and then flash with my desired ROM. I know I shouldn't let the battery run down, but I have several Wizards that I alternately use, and unused, the battery runs down and then the Wizard won't restart and the battery won't recharge.

Been there!
I solved this problem by buying an extra battery, which I keep with me, fully charged in my laptop case. As far as the wizard goes, it will only charge the battery if the operating system is booted and operational. I was lucky to find a site with a whole group of people who had the same problem and came up with a solution that is crude, but it works. Take a usb to mini usb cable and cut the mini end off. Strip the black and red wires, plug it into your laptop or desktop usb port and touch the black to the negative terminal of your battery and the red to the positive. Hold them in place for about 20-30 seconds, place the battery back in the phone and it should boot and then charge normally. Somewhere on this site you will find this information and a couple of posts from people who used basically the same tehnique with a nine volt battery. I can tell you the usb cable trick works, but I haven,t tried the battery approach.
Good Luck!

how to charge htc 8125 with no original usb cable and(or) without orig. wall charger

hi there.
shortly-i have this phone with no orig. usb cable and with no wall charger. it was friend of mine phone actualy. given to me with dead battery (i am not sure but i have trouwn it away long time ago)
first I did was to wait until friends of mine from china had sent to me 2 batteries compitable with the phone. what i discovered is that a normal ordinar usb cable cant charge the phone's battery it only can connect to the pc.
second what i did is this: i found my old charger from a very old panasonic cell phone and had a try to make the charging process with the simply contacting corresponding pinouts of the battery to the +&- of this same charger (somehow i dissasembled the plug of that charger and it became more "comfortable" to get in touch to the pinouts of the specific cingular's battery)
that unordinar way i did discovered that i can charge these batteries even not sure how much appropriate that other brand wall charger is. It seems its pretty much the same as a power characteristics.
Meanwhile (as i dont use this phone) i had some free time to search the net and to have better idea about that strange unordinar power charging matter with that model of a phone. The situation is that i cant find a place nearby me to buy a cheap usb and wall charger and become using this nice device finaly.
And also i dont want to buy these cable things before clearly understand why this happens ..
I did try also to charge this phone with a HTC brand wall charger but no sucsess again cause it seems this wall charger is for other htc phone (even same mini usb plug and same characteristics)
What i need is to have answers by someone very informed about that matter and let me know what exactly is the specific power charging matter (need explanations i mean) with this phone. If sharing some good ideas about how to remake others usb cable or wall charger for geting it work along for me in such a case , i will appreciate this very much
thanks

charge
hi ! please forgive me for my bad english! in this case you can charge your phone in 1 way! you need to procure a motorola or any charger with same socket but attention the charger must have 6 volts and no less than 500 mAh(milli amps)! you cut the wires and one wire put on the + of the battery you will see the signs on the battery an one wire at the - no matter which one. and you need stay with the wires 3 - 4 minutes on the battery ! then you put the battery on the phone it will start and then you cand fully charge it with the usb cable ! good luckk ! i hope my inf will help you!

no
no it doesnt work that way.
what i need is the simple answer : what is so special into the pinouts of htc cingular 8125 wall charger?
thats what i need only. Then I might figure out how to proceed
Thanks anyway

I don't know if anyone else has had trouble doing what I have done, but I've got the Cingular 8125 (HTC Wizard 100), which is also known as the HTC 8125.
1. I bought a car charger at a convenience store for $6 that had the mini-USB plug. It worked like a charm. Never any problem there.
2. I also bought a standard USB to mini-USB cable from the local computer store, because I had lost mine, and it also worked fine for both synchronization and for charging.
3. I bought a second wall charger, buying a standard mini-USB wall charger sold pretty much everywhere cellular phone chargers are sold. It's a common charging port, and this generic worked for me as well.
I'd be interested to hear if anyone has had problems with these types of devices not properly charging the unit.
Even my USB cable for my portable USB hard drive will power my unit.
EDIT: About your problem with it not charging. I had that problem about a year ago, when my battery got extremely old. It wouldn't charge even with the original charger. I just needed a new battery. The batteries get old and stop taking a charge after a certain amount of use. How long this takes depends on how heavily the batteries are used. They, like car batteries, do not last forever.

I had this problem when I had my wiz too. The battery died and drained, and my phone refused to charge it. I took it to an AT&T service center, and they had no clue what the problem was, and they wanted to issue me a replacement (it was a G4, I had a G3, I wasn't about to fiddle with that at the time.) So I asked to borrow a demo device they had there to fix it. I charged my battery on their demo device no problem, got it up to 3%, and finished charging it through my USB cable in the car socket.
It appears to be a sort of one-in-every-few-or-so type condition, but I got hit with it.

seems like noone can tell me if something special inside the mini-USB plug.
i realy cant charge. Very nice device, but i cant make it charging up whit cables.
guys, from up there, say that nothing special about the charging cables, but i trust what i see not what i read.

Perhaps there is a problem with your USB port on the device? USB charging has standards, and all devices that need power from a USB port have the same power pin configuration. Otherwise, they can't call it a USB connection. It would have to be called a proprietary connection, and they would have to change the plug size/dimensions and pins.
If there isn't a problem with your battery (which is the most likely source of your problem), then it may be a loose connection on your USB connector. This happens with a number of devices.
If a sync cable connects to the PC but will not charge the battery, then you definitely have an unusual pin detachment of some sort, or a bad battery.

thanks again..
for pity i was writing a lot to make my recent post and finaly it desapeared cause my session was left.. its funny in some case, but now i just dont want to repeat all what was intended to be posted
i give only the link where you might see why i was assuming that this is a kind of a special matter here with that htc 8125 charging
//pinouts.ru/CellularPhones-A-N/razrv3_charger_pinout.shtml
so, any more help will be appreciated a lot
thanks

SOLVED: HTC Wizard (Cingular 8125) Dead Battery Wont Charge
Dozzen said:
hi ! please forgive me for my bad english! in this case you can charge your phone in 1 way! you need to procure a motorola or any charger with same socket but attention the charger must have 6 volts and no less than 500 mAh(milli amps)! you cut the wires and one wire put on the + of the battery you will see the signs on the battery an one wire at the - no matter which one. and you need stay with the wires 3 - 4 minutes on the battery ! then you put the battery on the phone it will start and then you cand fully charge it with the usb cable ! good luckk ! i hope my inf will help you!
Click to expand...
Click to collapse
Hi - Too bad for the OP that asked questions but did not listen to this brilliant post.
I have confirmed that a variation of this method works perfectly! I have an old Cingular 8125 that I have been trying to charge for over a year using various USB chargers and NONE would charge the device.
The reason that this may happen is that the original charger has an output of 1 full amp which is much higher than most chargers. The voltage is the same but you need a charger that can handle such a strong current draw.
Nearly all USB chargers can only handle around 250milliamps - 500milliamps which is about half the power needed to breathe life into a fully discharged battery.
The best solution is to NEVER let the battery fully discharge.
Here are the details of what I did:
1. Find the best match charger of 5-6 DC Volts and ability to put out as close to one amp (1000mA) as possible. I chose an old Sanyo SCP-07ADT that is rated at DC 5.4V at 800mA. The plug can be any type, no need to be USB.
2. Cut the connector off the end of the cable and strip the outer black part up about an inch and then strip the positive and negative (red / black respectively) wires up about a millimeter, just enough to have bare metal ends to touch to a small area.
3. Take your battery out of the phone, look at the back of battery for the + and - marks which correlate to one of the metal connection points on your battery, this is where you will "touch" or "attach" the bare ends of the wires.
4. Plug the charger in making sure not to short your bare leads. Before you do this double check that the OUTPUT of your charger is indeed DC voltage so that you don't hurt yourself. You do not want AC output and it can be dangerous.
Then touch the bare end of the red wire to positive of battery, and black wire to negative terminal of your battery. I held them with my fingers while surfing the web for about five or ten minutes. I had no idea if anything was happening or not but it "felt" like the battery might have gotten just a bit warmer.
5. Unplug the home-made bare wire charger and put battery in your phone. Quickly attach a USB charger or just plug into a USB cable of your computer. I pushed it in and nothing happened at first but finally I heard the standard "bleep" when you plug a USB device in. I knew that I made progress because it never beeped before it took about 30 seconds and several "bleeps" of connecting/disconnecting from USB but eventually the charge light stayed on!
It's been about 30 minutes and I'm up to about 50% charge and been using the phone heavily while charging.
So, in summary... never let your battery discharge below 5% or you can only charge it with an OEM cable rated at 1amp (rare). IF you let it discharge to "dead" then charge for 5-10 minutes with the "wire" method and then charge normally!
Thanks to Dozzen for the original idea!!

Wizard that won't charge
When my Wizard/HTC 8125 goes dead my cure for the battery is to use a 9 volt charger with the wires stripped back also. But, my method is a bit different. I place a standard Christmas Tree light bulb (the newer small ones)in series with the charger wires. Observe the correct polarity. The battery is labeled + and - so that part is easy. By using the small light bulb you are doing 2 things. 1.You can see the slight glow from the bulb and know that proper connection is made. 2. You are limiting the charging current to the battery.
If you get really creative like I did you can solder a couple of small nails or in my case a set of red and black probes to the setup and the points on these nails/probes make for much easier connections. Note.... This method may take a few minutes longer but, is much easier on the battery.
In my experience once the battery is below a certain level NO charger that I plug in will work. I just purchased a used 8125 from eBay and brought it back to life most successfully with this method.

hy there my htc wizard battery whos dead so i charched with a cable with + and - the phone starts but when i try to connect to a usb or a adaptor it doesnt charge anymore it show me the charge icon on the baterry but it doesnt charge the usb works fine it's sync to my pc but it doesnt charge anymore... what sould i do?

So it seems no one touched on what really matters here.
A design flaw, in my opinion. The HTC Wizard cannot recharge via USB unless there is enough power to turn on. The reason is because it requires the OS to charge.
So, what many people already posted are very creative ways to charge your 8125. The easiest and cheapest way, in my opinion, is to use AA batteries.
1) Take two AA batteries and tape together so they are in series. Imagine it like this... [- AA battery #1 +][- AA battery #2 +]
2) Use two wires and tape one to each side of the AA's (one on the + side and another on the other battery's - side since the - of the first battery is connected to the + of the second).
--w-i-r-e--[- AA battery #1 +][- AA battery #2 +]--w-i-r-e--
3) Connect the positive (+) wire to the positive (+) side of the phone. By this I mean the 6 metal pieces that stick out to contact the phone battery. I did it by wrapping the wire around the top most one (or second top most, it's been over a year since I've done this.).
4) Connect the negative (-) wire to the negative (-) side of the phone. Again, bottom most or second bottom most (see #3).
5) Insert phone battery while the wires are still in and connected to the two AAs.
6) Let the power flow for 30 seconds or so and then try turning your phone on. This part is the important part because you cannot use a USB to mini-USB connected to your computer to charge the phone unless the operating system can function. Meaning, it needs to be turned on first.
7) Once the phone is on, plug in the mini-USB part and connect it to a computer. I'd recommend getting at least 5% battery before disconnecting the AAs, seeing as you need to be able to start up your phone long enough for the OS to boot. Once the OS boots, you can fully charge it through a normal USB to mini-USB connection on any computer.

old post but just wanted to say thanks. Used the wire to battery method and got phone turned on after 2 mins of holding wires to battery.