All,
I'm looking for a company which is able to clean and repair my HERM300 device.
It got wet and now when I want to charge it the led turns red.....
When I leave my device on a warm radiator it works and I can use the device...
But it seems to fail when it gets colder....
Any suggestions?
Cheers and thanks,
Hellejoep
hellejoep said:
All,
I'm looking for a company which is able to clean and repair my HERM300 device.
It got wet and now when I want to charge it the led turns red.....
When I leave my device on a warm radiator it works and I can use the device...
But it seems to fail when it gets colder....
Any suggestions?
Cheers and thanks,
Hellejoep
Click to expand...
Click to collapse
Can you say a bit more on "fail when it gets colder...."
I ask because soon maybe tonight I'm going to make a post on the charging and Red light problem but I'm just wondering exactly what you mean by "fail"
Cheers
Mike
mikechannon said:
Can you say a bit more on "fail when it gets colder...."
I ask because soon maybe tonight I'm going to make a post on the charging and Red light problem but I'm just wondering exactly what you mean by "fail"
Cheers
Mike
Click to expand...
Click to collapse
It blacks out as soon as I connect it to my activesync via USB....
Is it a short circuit?
Or something else?
Cheers,
Hellejoep
mikechannon said:
Can you say a bit more on "fail when it gets colder...."
I ask because soon maybe tonight I'm going to make a post on the charging and Red light problem but I'm just wondering exactly what you mean by "fail"
Cheers
Mike
Click to expand...
Click to collapse
I would like to add something, may be you already know, to red led knowledge. I have a car charger (just plain chinese USB charger with usb cable) When I connect my HERMES I could have 3 conditions: orange (charging) Nothing (not charging) or RED (?). If I soft reset, with charger connected, I ALWAYS have orange, after Windows Mobile screen, But if I disconnect and reconect I have ALWAYS No Light
connecting hermes to charger without battery also enables red light.
Charging Problems - Red Light of Death (RLOD)
Battery Charging Problems, in particular the RLOD so called because the phone refuses to charge and the red LED shows, indicating that the battery is NOT charging.
Background
Problems with charging are not HTC or Windows Mobile specific. Similar if not identical problems are reported across many models and platforms. The issues centre around the state of charge of the battery and the interpretive circuitry in the device and charger. Typically a device will show a Red light rather than an Amber charging light. (NB: RED LED always shows when battery is absent or fails to charge). see also http://forum.xda-developers.com/showpost.php?p=1076879&postcount=28
Getting the battery to start charging once this light is shown is not always straightforward and is as unpredictable and temperamental as priming a water pump (those that have done this will know what is meant). In other words, and to put it crudely, you need to kick start the system. Unfortunately those that have managed to do this have usually tried lots of things before it starts working again. This makes it hard to be absolutely certain about the solution other than perhaps the last 4 or 5 actions taken.
Those that have managed to recommence charging have not reported that the problem recurs on a frequent basis. (possible exception of in-car charging issue). This issue requires patience and time, (time maybe critical, it is possible the issue would resolve itself perhaps as charges dissipate within battery and circuitry involved). However the following points seem probable solutions and were thought to work by some who resolved the problem.
Failure to Charge (Red LED Lit when charger connected)
Causes of this problem are unclear, but in practical terms events leading up to this issue have included:
1
Leaving the phone on charge overnight (possibly but not necessarily with certain programmes or connections running) It seems a fault occurs in the charging system, which causes the battery charge to drain rather than increase. Resulting battery charge is very low. (Another Blog will be added concerning an Active Sync issue which can cause the battery to drain over-night through repeated connection attempts)
2
Through heavy use or not re-charging often enough so that the battery is permitted to reach a sub 10% charge (not precisely known but likely to be very low)
Possible Solutions:
A
1.) Remove battery
2.) Connect the phone to the charger or USB
3.) Insert the battery while connected to charger
4.) Red light should turn Amber
5.) Soft Reset
If this does not work immediately it is suggested that the battery be removed from the phone for around 1 hour and the above steps repeated.
OR
B
It has been found with some phones charging can be re-started by:
1 ) Remove battery
2 ) Connect charger (Optional. I would try this potential solution without the charger connected the first time I try this. If it fails to work then I would repeat the steps with the charger connected)
3 ) Holding the battery, line it up wiith the phone's battery contacts.
4 ) Move the battery rapidly on and off the contacts
6 ) Repeat the above until the Amber charging light comes on. So after perhaps connecting/disconnecting 20 times, insert the battery properly and give it a few seconds to see if the LED turns Amber.
7.) Soft Reset
NB: I have seen two reports where those attempting this report a fairly loud "pop" sound following which the phone began to charge. However in one case the person reported that they then had subsequent problems of signal reception on the phone and thought the popping sound may have been related to this.
OR
C
If your problems remain after trying this a few times you could always try the following to manually charge the battery a little (enough to let the phone charger circuit detect the battery is present when you put it back in)
1) Remove the battery from the phone!
2) Take 3 fresh AAA batteries in series (total 3 x 1.5V = 4.5V)
3) Connected the (+) wire to (+) on the battery
4) Connected the (-) wire to (-) on the battery
5) Hold this in place for 60 seconds.(possibly longer you are trying to charge it enough for charging circuitry to recognise there is a battery installed.
6) Put the battery in your phone
7) Switch on phone and start charging (via USB)
Hopefully you will get the Amber charging light.It may be worth repeating this a few times if not successful on the first try.
The electrical contacts are all important, poor contacts will render this a worthless exercise.
I leave it to you to decide how you connect the wires. If you have no other means you could enlist the help of someone to hold the batteries and wires together while you connect to the phone battery! Warning - Do not connect a mains based transformer to the battery with an incorrect charge rate (mAh) and voltage (V). Any attempt to force charge using mains transformers could be extremely hazardous (explosive). Only a qualified/competent person should attempt to charge the battery in this way. Similarly, even if you are using batteries to do this task, do not leave them connected for more than a few minutes and stop immediately if either set of batteries become warm.If the problem persists:The final resort - a new battery.
Mike
╤
Very good article Mike, I linked it on the Hermes problems wiki page
i just want to add my 2 cents to this, there was an earlier post on here that mentioned the car charger deal where it wont charge unless you turn the phone off, plug it in, then turn the phone.. right now i am on my 2nd 8525 and it has done this, but its not only the car charger (cheap belkin car charger) but it sometimes does this with usb cradle i got from ebay, i have opened the cradle and there isnt anything different, its a straight usb connection, hmm except now that i think about it there is a blue LED, but it shouldnt be drawing enough current to cause this. Also i have a motorola charger in my office that i used with my wizard (i believe output is slightly different, if i remember correctly its a .5 amp where as the HTC charger is 1 amp) but it also behaves in the same manner... the only 2 methods that work constantly and consistantly of plugging in without turning off is either the factory charger, or a regular usb cable on the pc..
just seems weird since all of these problematic situations worked fine on the wizard and i believe they both have the power requirements...
let me toss another idea in the fire here on this, something that just occured to me... i wonder if this somehow could be related to the factory installed driver for this. what made me think of this is how the battery meter only goes by 10%.. could this funky driver be the source of the problem?
shogunmark said:
right now i am on my 2nd 8525 and it has done this, but its not only the car charger (cheap belkin car charger) but it sometimes does this with usb cradle i got from ebay
Click to expand...
Click to collapse
If your cradle is not connected to your PC, or if your PC is off while you see the behaviour you described, then the likely reason is that pin 4 of the Mini USB connector isn't grounded on both your car charger and cradle. See here for more details.
Cheers
Daniel
pof said:
Very good article Mike, I linked it on the Hermes problems wiki page
Click to expand...
Click to collapse
Cheers pof.
Some of the type sizes are a bit strange (but readable!) serves me right for copying and pasting from Word formatting!
Tadzio's link is good/informative and I edited in a link to it in my post - though it's on this page anyway.
Mike
tadzio said:
If your cradle is not connected to your PC, or if your PC is off while you see the behaviour you described, then the likely reason is that pin 4 of the Mini USB connector isn't grounded on both your car charger and cradle. See here for more details.
Cheers
Daniel
Click to expand...
Click to collapse
cradle is connected to pc at all times, and i will deal with the car charger for now cause my HTC one should be arriving any week now, but thanks for the tip!
8525 (hermes) Charging may be voltage sensitive
I have noticed with my new 8525 (USA Cingular model of phone) that it came with a 5.5V charger. Whenever I connect to a 5.0 V USB source charging the phone is very "iffy". Given that the standard for USB is 5.0 V (4.75 - 5.25) there is a problem with the design. My question for the HTC crowd is can this be fixed via a ROM change or are we stuck with a bad design?
hellejoep said:
All,
I'm looking for a company which is able to clean and repair my HERM300 device.
It got wet and now when I want to charge it the led turns red.....
When I leave my device on a warm radiator it works and I can use the device...
But it seems to fail when it gets colder....
Any suggestions?
Cheers and thanks,
Hellejoep
Click to expand...
Click to collapse
http://www.america.htc.com/support/service-repairs.html
Since you got it wet, it is most likely not covered by the warranty, these and the numbers for out of warranty repair if you live in the U.S. I know that for cingular, you have to ship it to them yourself, and they will charge you a $28 diagnostic fee, before telling you how much is costs to fix the problem (if they even can)
heh here almost the same, providers are charging ~$29.5 USD as diagnostic fee but they are more polite, they first tell estimated costs, and only ask for the sum if you (usually) don't order the repair but need back your phone
Hellejoep:
if you are willing to send it abroad (inside EU) and you are either not need "overnight return" or such nonsense or cover the extra costs such operations really need, you may contact me. no diagnostics fee or anything such (though you will have a small loss.
about the charging problem:
the same issue occurs also in Wizard/Prophet, and Charmer (compactII) as well. though not in Magician, even so that they share the exactly same battery.
I believe it must have something to do with the charging controller. I don't have a disassembled unit at home with me now, but I suppose it should be a crap companion chip from Texas, to be interfaced with the ever-worst TI OMAP platform
(sorry, no hard feelings, pals, but someone using such one as an actual everyday phone must have some sorta mental problem )
strange battery issue
Hi all,
I've a similar issue with any charger.
It happened first with car charger (one cradle with an usb output): sometimes it charged, most of all it charged only when power was off.
Now I cannot charge with any method. (those described here: battery charging problems)
Usb cable (it's not original), original power supply, even with the y cable.
When i try to charge, it drain battery (i tried with a new one) and amber led blinks slowly instead to be firmly light.
There's anything I can do?
It's a SPV M3100 buyed two months ago on ebay.
I tried also with two roms WM6 official release ITA ver and Schap's 3.54b ITA ROM WM6
radio 1.48
Any suggestions?
Herm200/tytn problems
hi to all,
i read most of your post on possible problems with this PDA (HERM200/HTC TYTN).
i'll try to spent some few words to explain the story around my pda.
i live in italy and i bought the TYTN on december 2006 and for 6 months with his software problems i used it day by day in my business activity, untill one day, it falled down the ground from my and with all the leather cover (bundled with the pda, an hard black belt cover); then i took it and picked up a telephone number from my addres book and then putted it in charge for all the night; when, late in the morning, i took it, i noted that there was still the red light of the battery indicator and then PDA didn't turned on.
i tried to make soft/hard reset but nothing.
I carried to the italian warranty service of HTC and after 7 days they deliver to me the PDA in the same state that i carried; on the technical report there was: pcb damaged, battery connector pinouts damaged, pda not Repairable - out of warranty.
i thought: "i have had a lot of care for this PDA that still look like as new one"
and now i have a 700€ of unusefull PDA.
Last day i finally decided to open my PDA to find broken pieces and more.... but nothing.... i observed really well: NOTHING of wrong.
Now i will to know if somebody of you, can suggest me something to revive my PDA or suggest me any service center (affidable) in europe (not like the italian one) where to send it for maintenance: I DONT WANT TO THROW OUT MY PDA!
Thank you in advance for your attention and patience.
ps: sorry for my english, i hope it will be comprehensive.
therock-htc said:
Now i will to know if somebody of you, can suggest me something to revive my PDA or suggest me any service center (affidable) in europe (not like the italian one) where to send it for maintenance: I DONT WANT TO THROW OUT MY PDA!
Click to expand...
Click to collapse
If I understood you correctly, your TyTN still works - it just cannot charge the battery, right?
Then, probably one of the cheapest (although not perfect) solutions is to get a cradle that can charge a battery outside the TyTN (like this one on eBay). You will have to power down your TyTN, remove the battery and put it in the cradle every other night or so, so it's not very convenient. But it's cheap. Maybe you'll want to keep this as "plan B" in your mind while you look for a more perfect solution.
Cheers
tadzio
elehcimo said:
Hi all,
I've a similar issue with any charger.
It happened first with car charger (one cradle with an usb output): sometimes it charged, most of all it charged only when power was off.
Now I cannot charge with any method. (those described here: battery charging problems)
Usb cable (it's not original), original power supply, even with the y cable.
When i try to charge, it drain battery (i tried with a new one) and amber led blinks slowly instead to be firmly light.
There's anything I can do?
It's a SPV M3100 buyed two months ago on ebay.
I tried also with two roms WM6 official release ITA ver and Schap's 3.54b ITA ROM WM6
radio 1.48
Any suggestions?
Click to expand...
Click to collapse
Hello!
I had also a battery charging problems with my MDA Vario II (TyTN; Hermes; HERM300):
1. Charging from the AC mains supply with the original miniUSB 5V charger: no problems.
2. Charging in the car with the non-original car lighter miniUSB 5V charger: it was charged only when the phone was OFF; no charging when the phone was ON.
3. Charging with the USB-miniUSB 5V cable connected to the notebook: it is charging only when the phone is OFF; no charging when the phone is ON.
So I asked myself: what is the difference between all these three cases? They are all miniUSB 5V power sources... And I found out an answer: It should be a matter of the USB current amperage.
Original AC miniUSB 5V charger delivered with the phone is 5V/ 1A. When I have bought the car 5V miniUSB charger with the 1A (one amper) amperage - there is no problem with car battery charging anymore... ;-) The phone is charged either way: ON or OFF.
But is it possible to charge the battery correctly from the notebook? I think not, because I have no influence on the current value from the 5V notebook USB.
Previously I had MDA Vario (Wizard): in this phone there were no battery charging problems... I wonder why the are some with the Hermes...
Take care,
Przemo
Przemo_55 said:
And I found out an answer: It should be a matter of the USB current amperage.
Click to expand...
Click to collapse
This is not correct. The problem is well understood and has been discussed several times.
The key is that your device tries to sense what it is connected to:
- if there is USB data traffic, it concludes that it is connected to a computer. It will then negotiate the current (power) it can draw from the USB port with that computer.
- otherwise, your device checks if pin 4 of the connector is pulled to ground. If yes, it concludes that is is connected to a dedicated USB charger, and starts charging, consuming as much power as it needs. This mechanism seems to work only if the device is on - and sometimes not even then (bug?). I guess the mechanism is implemented in software, so it can't function when it is off.
- otherwise, it doesn't know what it's connected to. Could be a computer in stand-by that didn't power off its USB ports or something. Your device concludes it may be unwise to start charging (could, for example, drain the other device's battery).
The cheap after-market chargers do not connect pin 4 to ground (pin 5), so your device doesn't charge. If you are really good with a soldering iron, try connecting pins 4 and 5 of the charger's USB connector, and you'll see that your device will start charging with it.
Cheers
tadzio
tadzio said:
If I understood you correctly, your TyTN still works - it just cannot charge the battery, right?
Then, probably one of the cheapest (although not perfect) solutions is to get a cradle that can charge a battery outside the TyTN (like this one on eBay). You will have to power down your TyTN, remove the battery and put it in the cradle every other night or so, so it's not very convenient. But it's cheap. Maybe you'll want to keep this as "plan B" in your mind while you look for a more perfect solution.
Cheers
tadzio
Click to expand...
Click to collapse
Thank youu Tadzio,
but my PDA is DEAD !
I still don't try to charge the battery separetly.
The reason is that when i carried the PDA to service i leaved the PDA and Battery: i dont wanto to believe that service dont check the battery !??!?
However , i will try to charge the battery separetly and then i will know you the outcome.
Thanx and Cheers
Therock-htc
Related
Hi Guys
I have a problem with my TyTN at the moment.
My device is not charging.
Yesterday i put it in my Docking Station and wait a little time.
But Now the Tynt isnt charged.
I think ist a Problem with my TyTN Hardware.
I have all Power Supplys used they i have, but it doesent work.
Can you help me?
Its this a problem with the accu or a fuse on the circuit ?
Sorry for my broken english i hope you understand me.
Regards Patrik Laube
Hello,
first of all, try to soft reset the device.
If it fails, hard reset it.
If it doesn't work, go the service center.
Good luck
The above advice is fine. But you did not say if any of the LEDs are lit.
Do you get the red NO CHARGE LED?
Does your phone operate normally except for not charging?
Mike
Hello
My Phone is working fine but i cant charge it with the original HTC adapter.
I must load the accu with a special loader.
USB and Charge dont work....
And i have no warranty I cant send it to my operator.
When i plug in the USB Cable it doesent make everthing.
I think it was a to high voltage on the USB or the USB Ground ( - ) had a electrical Power for a litte moment.
Have you an idea?
Thanks for yur help.
Regards Patrik
I had a similar problem, which was sorted by a new rom, but I ascertained it was software problem when I realised it charged when powered off.
PatrikLaube said:
Hello
USB and Charge dont work....
And i have no warranty I cant send it to my operator.
Have you an idea?
Thanks for yur help.
Regards Patrik
Click to expand...
Click to collapse
hi,
try this: when your device is connected via usb, tab on the battery icon in the taskbar on you device, go to the register "advanced" and check/uncheck "When Device is turned on, do not charge the battery when connected to the pc"
thats it
greetz
mizi
I'm having an issue along these lines, also.
My phone has been working fine untill the other night when I tried to charge it via the wall electrical outlet. It will not charge at all, the battery has been drained to nothing and I can't turn it on. The yellowish light doesn't turn on when I plug it in like it used to.
I don't know if this is a battery issue or an issue with the USB connection inside of the phone. On a side note, when it did have power and I tried to connect it to the USB via the PC; it didn't work. The phone was on, but the computer didn't even notice the phone was plugged in. That leads me to believe it would be a connection issue; but I'm not quite sure.
If anyone has anything they can add to this I would appreciate it, thank you.
P.S. Bringing it to a service center is a bit out of the question in the mean time seeing as it was bought on eBay and funds are limited for the time-being.
MiZi666 said:
hi,
try this: when your device is connected via usb, tab on the battery icon in the taskbar on you device, go to the register "advanced" and check/uncheck "When Device is turned on, do not charge the battery when connected to the pc"
thats it
greetz
mizi
Click to expand...
Click to collapse
Hello, I cannot find the "When Device is turned on, do not charge the battery when connected to the pc" in my device. My Rom is WM6.1 CE OS 5.2.20273 cooked by dvha79_ddt.
My HTC TyTN has the sample problem, but i can use the USB to charge normally. It cannot work using my AC adapter Only when the device is open...
About your Battery Issue.
I'll tell you exactly why ur phone isnt charging anymore... If you have been charging it alot on the USB or pretty much any!! charging on the USB u have killed ur battery, never charge your phone on the USB it kinda sucks they should make these phones able to be Sync'd thru USB without a battery cause these batteries should not be powered thru the USB over Time... from syncing to your pc will kill these batteries i have noticed that when u sync this Tytn Ithru USB and the device is at say 70% it charges up to 100% pretty fast i would recommand to you and anyone who reads this dont sync your TYTN or any HTCC phone for to long to the USB Cause it will Trash your batteries Life down the road... Hope this was HELPFUL.
Cheers
Paul
PatrikLaube said:
Hello
My Phone is working fine but i cant charge it with the original HTC adapter.
I must load the accu with a special loader.
USB and Charge dont work....
And i have no warranty I cant send it to my operator.
When i plug in the USB Cable it doesent make everthing.
I think it was a to high voltage on the USB or the USB Ground ( - ) had a electrical Power for a litte moment.
Have you an idea?
Thanks for yur help.
Regards Patrik
Click to expand...
Click to collapse
hi, did anyone solve this problem ? ive got the same problem with my htc touch cruise, i think it charges when turned off but doesnt when on. the orange light doesnt turn on when i plug usb to charge it and it doesnt sync thru the PC neither.
Does anyone has a solution to this ?Thanks a lot!
does anyone has a solution to this ?
hi, did anyone solve this problem ? ive got the same problem with my htc touch cruise, i think it charges when turned off but doesnt when on. the orange light doesnt turn on when i plug usb to charge it and it doesnt sync thru the PC neither.
Does anyone has a solution to this ?Thanks a lot!
^I'm having the same problem with my herm200. I did the soft reset, hard reset changed ROMs but still the same problem. I don't think it's the usb connector because if it is it wouldn't have been able to charge the phone even if it's turned off. Before I'm able to charge it turned on but it would take a few minutes before the orange led turns on, but when I use the phone or if I receive a text the orange led would turn off it's like the charger disconnects but after a few minutes it would go back again. Now it just wouldn't charge turned on, sometimes it gets worse where it just wouldn't charge on or off.
Now I'm already planning to buy an external battery charger.
gypsygirl13 said:
^I'm having the same problem with my herm200. I did the soft reset, hard reset changed ROMs but still the same problem. I don't think it's the usb connector because if it is it wouldn't have been able to charge the phone even if it's turned off. Before I'm able to charge it turned on but it would take a few minutes before the orange led turns on, but when I use the phone or if I receive a text the orange led would turn off it's like the charger disconnects but after a few minutes it would go back again. Now it just wouldn't charge turned on, sometimes it gets worse where it just wouldn't charge on or off.
Now I'm already planning to buy an external battery charger.
Click to expand...
Click to collapse
Are you using an official 1000mA charger? (Not a 500mA one) 500mA ones work, but they are under-powered and can cause strange behaviour, like not charging whilst turned on or whilst on a call. Similar problems can be found with car-chargers that will not charge until the device is soft reset.
Mike
^no it's not the official charger, I have this usb wall charger called Power Juice (phone and mp3 charger).
Input Voltage: AC100-240V
Output Voltage: 5V
Output Current:1000mAh
Do you think it's because I'm not using the original charger?
fixed my charging problems
The boyfriend told me to try a new cable for my charger so he bought me a 5pin usb cable, tried it at home and it worked! I still need to turn off the screen sometimes but that's ok at least I don't have to turn off the phone anymore. Now my battery charges less than 3 hours.
Hold both SoftKeys and Then press the Power button
Or you can also hold both softkeys and then put your stylus into the reset hole.
answer why it does not charge through the usb
Sorry for the very very late response. Under electrical legislation all hand held electrical devices must be insulated and fused. Some of the chargers that you can purchase are sealed without fuse which indicates that the phone has a fuse contained within its circuitry (or there may be 2 fuses one in each device) .
The problem you have encountered is that you have connected your phone to a computer or mains supply to charge. There has been a surge in the electrical supply either on connection or by un-connecting from these supplies (e.g. connect to the computer as it is booting would see a 65w signal through the USB) and this more often than not blows the fuse which sits on the PCB (printed circuit board) just after the usb connection internally to the phone.
you can either have the fuse fixed for 20/25 gbp or you can purchase a new circuit board or you can use an external charger for the battery. As it is only the power input point that is faulty.
hope this helps
Since we are at this non-charging & battery issue, I would like to ask this question on the D838pro. My battery won't charge even after 24 hours of charging. The red LED blinks thru the whole process. The LED did not turn on to orange or green. It is the battery problem because my spare battery works well. I would like to know what is wrong with the battery as I am willing to strip down the battery. Could it be the battery circuit or wiring that had fired?
cyberdroxxx said:
Since we are at this non-charging & battery issue, I would like to ask this question on the D838pro. My battery won't charge even after 24 hours of charging. The red LED blinks thru the whole process. The LED did not turn on to orange or green. It is the battery problem because my spare battery works well. I would like to know what is wrong with the battery as I am willing to strip down the battery. Could it be the battery circuit or wiring that had fired?
Click to expand...
Click to collapse
Never tried stripping down a battery, some things... well, just don't seem worth it. However as a learning exercise it might be interesting. Without lots of testing on a good battery with a multimeter then I have no clue what the readings should be between all the contacts. (Now there's a little job for you) It is as likely the internal structure of the battery is screwed as it is to be a wiring problem.
If you solve it you can certainly report back here
Mike
Hi,
That's the first time I am not able to find in this great forum a solution for a problem with one of my 2 wizards (i love this machine...)
Yesterday, one suddenly did not power on. I knew that the battery was pretty low, so I guessed was just discharged. But once I plugged it at home to the wall charger, no amber light appeared, nothing powered on! When I replaced the battery with a fresh one, nothing changed... and when I tried the "bad" battery with my second wizard+wall charger, I confirmed the battery was almost empty (2%), but worked fine.
I tried to plug the mobile to the computer, but nothing... to soft-, hard-resets... the bootloader reset... but my wizard did not respond electrically or electronically to anything... any idea what could be happening? any possible solution? I do not remember exactly which rom I was wearing now, if that matters... probably a FariaWM6_realthing_crossbow
thanks to all in any case
marcos
Maybe out of sight accident
why you leave alone your lovely wizard and so aprecciated mmmm....
its xtrange but as you say i think this kind of forum may helps you with software... took it to a cellphone repair center... they has multimeters to know where does the energy stops... maybe a little electronic component has burn it down. or try the not original and official wall chargers withj specific mhz and amperage, try something more hard.
hope i help you
more news
After being overnight without the battery, this morning I tried a "resurrection"
I just put back the battery, did a softreset, and it worked!... really!? no... just the first two screens (HTC welcome and machine tests) It did not go forward, and a second reset it did not work either... now it's again like yesterday, just dead
I think there is something else than just an electronic problem, but who knows. I recommend you not to let the battery too low!
Marcos
Charging a completely dead Wizard battery
Delapena,
I've had this problem a bunch of times with my Wizard (Cingular 8125 branded version). I was able to get it working again using the instructions of a VERY helpful person(s) who I want to give credit to but cant remember right now (sorry in advance) so just FYI this works for me, but the credit goes to the original poster (will edit later if I recall).
Easiest method (if available):
1) Locate your STOCK 5vdc/1.0A wall charger.
2) Remove stock battery, put it in a ziplock bag, place in freezer for 5-10 min or so. This should minimize the internal resistance of the battery to boost VDC across the terminals (in case you ran the battery very, very very dead).
3) After the battery is good and cold, put it back in the phone; DO NOT PRESS THE POWER BUTTON!
4) Plug the 5vdc/1.0AMP STOCK WALL CHARGER into the phone.
5) Charging indicator (solid amber LED) should light up after 5-10 seconds with no other indications (no screen, no beeps, just solid amber LED ON).
It's my understanding (may be wrong) that the 1.0amp wall charger uses/supplies 5vdc one one or more of the mini-usb plug pins than the standard USB->mini-usb cable used for standard data-transfer on standard USB-spec devices. Also, the wall charger sources a full AMP of current at 5vdc, as opposed to the 0.5amp each USB host IC is allowed to source (e.g. the USB host IC on your motherboard/front/back of computerbox).
...reply to this if you want the comprehensive method. Ill research if above doesnt work / you dont have the charger. Swamped at present though; if you need the full blown recharge-the-battery-from-the-stoneage method ill look it up---dont want to give you invalid info.
If you dont want to wait (i'd understand, been there), try searching around a bit if you havent already found what your looking for.
Reply back if you need more help, otherwise, good luck and replace your battery with a new one asap!
Cheers
(again, no credit to me on this one, got this solution from somewhere else on the forum a long while back...credit to original poster!!)
Sir,
I didnt read what you had already tried. My wizard is rebooting constantly as well. My thought is that my battery is so old that the battery charging chemistry is so out of whack that the battery charging / voltage sensing circuit is all sorts of confused as to where the (really old worn out) battery is on its charging curve.
I'm guessing that my phone is rebooting because the battery fails to supply adequate voltage at x.xx amps of current draw to the phone's internal voltage regulator. When the IVR cuts out, the phone poops its pants.
I'm currently looking for a battery replacement myself.
more... but less
Thanks for the help, brhestir. But did not work for me. Actually, I tried with the 3 batteries I have, which actually work OK in my second wizard.
The only thing I am able to "slighlty" reproduce till now:
1) Wizard remains several hours with any battery plugged
2) I put the battery back
3) I switch it on or do any kind of reset
4) Just sometimes, the machine starts up, but gets hanged up after the first screens
5) most of the times, after this... the screen turns white slowwwwly, till it switches off
6) only once, I managed to get the bootloader screen, which stayed like that with any problems... but the computer cannot connect to it, so impossible to change the rom.
Next step: to dismantle the machine (prior step before throwing it through the window)
Marcos
brhestir said:
Delapena,
I've had this problem a bunch of times with my Wizard (Cingular 8125 branded version). I was able to get it working again using the instructions of a VERY helpful person(s) who I want to give credit to but cant remember right now (sorry in advance) so just FYI this works for me, but the credit goes to the original poster (will edit later if I recall).
Easiest method (if available):
1) Locate your STOCK 5vdc/1.0A wall charger.
2) Remove stock battery, put it in a ziplock bag, place in freezer for 5-10 min or so. This should minimize the internal resistance of the battery to boost VDC across the terminals (in case you ran the battery very, very very dead).
3) After the battery is good and cold, put it back in the phone; DO NOT PRESS THE POWER BUTTON!
4) Plug the 5vdc/1.0AMP STOCK WALL CHARGER into the phone.
5) Charging indicator (solid amber LED) should light up after 5-10 seconds with no other indications (no screen, no beeps, just solid amber LED ON).
It's my understanding (may be wrong) that the 1.0amp wall charger uses/supplies 5vdc one one or more of the mini-usb plug pins than the standard USB->mini-usb cable used for standard data-transfer on standard USB-spec devices. Also, the wall charger sources a full AMP of current at 5vdc, as opposed to the 0.5amp each USB host IC is allowed to source (e.g. the USB host IC on your motherboard/front/back of computerbox).
...reply to this if you want the comprehensive method. Ill research if above doesnt work / you dont have the charger. Swamped at present though; if you need the full blown recharge-the-battery-from-the-stoneage method ill look it up---dont want to give you invalid info.
If you dont want to wait (i'd understand, been there), try searching around a bit if you havent already found what your looking for.
Reply back if you need more help, otherwise, good luck and replace your battery with a new one asap!
Cheers
(again, no credit to me on this one, got this solution from somewhere else on the forum a long while back...credit to original poster!!)
Click to expand...
Click to collapse
wow i just ran into the same problem today.. my battery was low tried to plug into the cigar lighter but the fuse was blown due to another object i had plugged in so i didn't get a chance to charge it, the phone was fine all day until i left work it was completely dead.. no amber light for the charger.. have you had any luck?
hi everyone,
i solved this problem by creating a sort of bypass for the battery...
i bought a special battery used for some circuits experiments which is 4,5v..
i connected the + and - with the phone contacts, with the battery plugged...turn on the phone until the orange light is on and leave it until charge is full...
this is cause phone needs a minimum of charge to start recharge circuit...
Yes the same problem on every post
The thing of cooling batteries is an old but knowledge charging fast option but it brokes your performance batt drain so i recomend a new full battery ok? is the only way or...... charge the one you have fully fully.
and try again! tu plugin the batt once at time and again and again it wouldnt boot cause its too low to begin the OS and let you charge with the wallcharger... to charge with the wall or usb you need a bootable and functional OS ok?
hope you can find a way to charge your batt at least sufficient to boot the OS ok?
bye
well good news! 20 minutes in the freezer + 5v + 1a = win
CONGRATS!!!!!!!!!!!!!!!!!!!!!
mp86 said:
well good news! 20 minutes in the freezer + 5v + 1a = win
Click to expand...
Click to collapse
So dont ever let the batt drains to the hell down forever hahaha.
+ Que PPC said:
So dont ever let the batt drains to the hell down forever hahaha.
Click to expand...
Click to collapse
lol it was an accident i thought it was charging in the car!
Hello Gentlemen,
I have charging problem with mu Wizard Qtek 9100... its not battery issue I have 2 working batteries...
The phone starts only when the charger is not pluged in..
Otherwise RED light is shown and the phone refuse to start so I need to remove the charger and the battery and then put the battery back so I can start the phone...
When the devise has started already I can plug the charger but the Windows is not showing ORANGE light and is not showing charging....
The device acts very wired and is turning off with no reason...
This happened when my charger burned up while charging my device...
Now I have no sound,the device is SIM locked and is turning off sometimes for no reason....
I believe it is a hardware problem I guess I need new mainboard?
Please advice if this could be a software issue....
The device is G4 IPL/SPL 2.26.0001
Please advice,
Thank a lot...
Regards,
Mitko B.
Battery problem
Hi,
I know old post, but it may help somebody.
It is possible that your windows has switch off the battery charging circuit for some reason.
You MAY be able to get it working with the following trick:-
You need 3 x 1.5 volt AA batteries, some wire and 2 pins
You need to join the batteries together in series (i.e. end to end)
Next make a negative lead from the negative of the battery pack to one of the pins.
The make a positive lead in the same way.
Open the battery cover of your Wizard.
Connect the USB charging cable.
Put the negative pin you have just made into the gap between the battery and the charging pins in the Wizard - MAKE SURE YOU ONLY CONNECT IT TO THE PIN NEAREST TO THE USB PORT.
Now comes the tricky bit - take the positive pin you have just made and touch it on the charging pin which is NEAREST to the power on switch.
If all goes well the charging light on your Wizard should turn orange indicating that it is charging.
You might have to try this a few times, I was never sure if you had to keep the external battry connection on for any length of time or just a quick connection would do the trick. I suppose it depends on the state of the Wizards battery.
This is NOT my work! I do not want to take credit for something that is already documented on this site as it helped me get my battery working again.
Regards,
John
thanks a lot!
saved my wifes phone. Is this problem (happend twice already) something that I can address with a new rom, anyone knows?
I also have the remove the battery go back to Feb2006 issue. Device is off warranty by a few good years. Is it something an experienced electronics person could try (without destroying the phone that is...)
Cheers
V.
Worked for me too
I had just bought a new battery for my Qtek 9100.
This one:
sku.23974 at dealextreme.com
My 9100 had been dead since 2006 (because the battery was dead ...)
And i got a new phone.
but i tought it was to good to throw away, so i bought the new battery.
But i did let it run out of battery, and it would not take the charge.
but this trick did the job
Thanks
Hi all,
Just wanted to sign up to say thank-you - I chanced upon this forum while seeking a solution to the same problem.
I'm happy to report that the 'jump-start' works perfectly!!
I actually used the slightly different method, described in another thread on this forum:
Take a USB-to-Mini B cable. One that you won't need ever again.
Cut the Mini B end off and strip back the outer casing. Inside is a wire mesh and within that a foil lining. Pull these both back.
Now find and strip the black and red wires. The wires are thin and this is a fiddly job, especially if you have large hands, so this works best if you screw the exposed wire strands up into little balls.
Remove the battery from your Qtek 9100 (or whichever model it is). Pay attention to which pin goes to which contact and so identify which ones are the positive and negative contacts on the battery - It is described above in Heinkeljb's post.
Now, plug the USB into your PC (which should be switched on and running) and connect the black wire to the negative (and red to positive) contact on your battery.
Hold for a good 30 seconds.
Now reinsert the battery into the phone and attempt to charge.
You may need to 'jump' your battery a few times....
Once again, many thanks to teh lovely people here for saving my beloved Qtek 9100!!!!!
Hi all,
My TD1 would charge from any mini-usb charger (such as the one I have with my TomTom). I put the TD2 on charge from one of these last night. The front light went orange, and the battery status changed to charging. However, I wake up this morning (7 hours later) and the light is still orange. I disconnect and look at the battery info and it says the last charge was yesterday.
Is the TD2 fussy about which charger you use? I really hope HTC are not pulling an Apple and locking their devices to only their accessories!
R
rakh1 said:
Hi all,
My TD1 would charge from any mini-usb charger (such as the one I have with my TomTom). I put the TD2 on charge from one of these last night. The front light went orange, and the battery status changed to charging. However, I wake up this morning (7 hours later) and the light is still orange. I disconnect and look at the battery info and it says the last charge was yesterday.
Is the TD2 fussy about which charger you use? I really hope HTC are not pulling an Apple and locking their devices to only their accessories!
R
Click to expand...
Click to collapse
I think I remember reading something about an option for not charging the battery when connected on PC USB (presumably for saving laptop batteries ;-) ) in the manual.
So I guess that the TD2 has a way to detect if it is plugged into a charger or a laptop, and maybe it can do that only with HTC charger, believing your charger is in fact a laptop. I would have guessed they use the activesync status to differentiate between PC and charger, but maybe not ;-)
So what could maybe solve your problem is to select "charging battery if plugged to a computer", I think it is in the touchflow 3D options somewhere... I would play with those options to check if it improve things...
Settings - All Settings - Batter - (Battery Tab). "When device is turned on, do not chagre the battery when connected to the PC.".
For me this is unticked - and when it was plugged in the battery reported as 'charging'.
Strange!
R
rakh1 said:
Settings - All Settings - Batter - (Battery Tab). "When device is turned on, do not chagre the battery when connected to the PC.".
For me this is unticked - and when it was plugged in the battery reported as 'charging'.
Strange!
R
Click to expand...
Click to collapse
Does it work with the standard HTC charger?
And plugging to a PC?
If yes, your other charger may be a little light in specs (amperage too small, or voltage slightly below USB specs) and the TD2 may be picky regarding this...
I would also inspect the microusb plug of the charger to check for dirt/corrosion/deformation, and also the battery within the device: I already had intermittent problems like that caused by imperfect connections: the device was in a charging state, but no actual charging did occur. Replugging carefully after blowing on the plugs solved the problem....
From past experiences, all my HTC phones charges up with any USB cables or chargers, even my HD. So may your battery is not working some how... best thing to do is try charging it with your original charger or connect your device to your computer, it should charge up. If not, then take it back to your dealer man! I don't want to say it but maybe you have a lemon...
Hi all,
It charges well from the supplied wall charger. It also appears to be charging well from the computer. So, this leaves me to suspect the other (non HTC) charger.
Thanks for your help....
R
OK - this just getds weirder and weirder...
Yesterday, plugged into PC all day whilst I was working. After a while green light so fully charged. Went out for an hour or two and when I came back I put it on a different wall charger for a test (my old TD1 one) and after 30 mins or so green light - so fully charged again.
So, I thought - this is great, it proves the other wall charger has a problem. Before bed a few hours later I took the TD1 charger and put it in the bedroom. Plugged the TD2 into it overnight. Woke up this morning, and orange light???!!!
Put it into the computer this morning and after 15 mins - green light???
CONFUSED!!!
Could it be some function whereby it won't charge a bettery that has been charged full in the past x hours or so??? Is anyone else seeing anything like this????
R
I think you have might have a duffed battery. I think you should really check it out.
I use a Motorola universal mini-usb charger i mine car and I haven't noticed any different behavior than using the supplied HTC charger or HTC usb cable in my laptop..
I put it on the supplied charger for 12 hours and it did not charge at all despite the orange light being on. As I am within 7 days I've asked DeviceWire to refund or replace...
R
Way to go, you should get a new one!
check the connection!
rakh1 said:
I put it on the supplied charger for 12 hours and it did not charge at all despite the orange light being on. As I am within 7 days I've asked DeviceWire to refund or replace...
R
Click to expand...
Click to collapse
First of all, yes you are.. IF the device is faulty!
from experience, I know that some cables dont charge the device.. First of all make sure there isnt some dust or stuff in the connection. secondly, try resetting the device.. If the orange light is on, then it only means some of the pins in the EXTusb connection have been shorted, my reccomendation, check the pins on the miniUSB connector on the phone, and make sure you didn't bend some.
Hey all,
No bent pins.
No dust or dirt in the socket/plug.
Tried 3 (HTC) wall chargers - all the same behaviour.
Tried resetting the device.
No luck
R
I especially used my USB-Charger this night to charge the device.
It is a Hama USB Charger (Prod# 00014095, you can find it with this on google).
It has an output of 800 mA, while the original hast 1000 mA.
But it charged up to 100% and was "green" this morning.
So it seems to work and is really Small in size
Regards Thorsten
Well, this has been a problem for me from the start and all I have used are HTC chargers. I've not had anything like this sort of issue with the previous HTC phones I've owned (and there have been a few - check sig). What confused me was that it does appear to accept charge from the USB port of a computer - which is just odd??!?!??
Anyway, I think this is unacceptable from a new product so I've asked for a refund/replacement. Awaiting a reply from Devicewire.
R
Whats weird,
My TyTn has some probs in this department.
From time to time, setting it on USB power, will not even lit the charge-light.
And it will not charge.
I have to reset it and then it works.
Dont know what that is.
DeviceWire sent me an RMA. In the meantime I hard reset the device again after confirming that the wall charger would not go above 89% charge - 9 out of 10 bars (I installed a prog to give me a % reading).
After hard reset the battery went from 89% to 100%. I am now running it down again - before I give it one last chance overnight. If I wake up tomorrow and it is still orange and at 9 of 10 bars then off it goes...
R
Fingers are crossed for you mate! Hope it goes well.
This just gets stranger - after *this* hard reset it now appears to be working as expected - woke up this morning to a green light for the first time!!
So, was this just a software thing - solved by a couple of hard resets - or might there still be a problem lurking underneath???
Problem now is that if I send it back to DW they'll confirm it is working as expected. If I wait and do not send it I run out of the 'return within 7 days for a refund' and will have to reply on HTC aftercare (horror!!).
What to do!!!???
R
I'd still return it but in your RMA notice stipulate that you suspect the problem "seems" fixed but say it might come back again and on that note are still returning it for a replacement/refund.
hi there.
shortly-i have this phone with no orig. usb cable and with no wall charger. it was friend of mine phone actualy. given to me with dead battery (i am not sure but i have trouwn it away long time ago)
first I did was to wait until friends of mine from china had sent to me 2 batteries compitable with the phone. what i discovered is that a normal ordinar usb cable cant charge the phone's battery it only can connect to the pc.
second what i did is this: i found my old charger from a very old panasonic cell phone and had a try to make the charging process with the simply contacting corresponding pinouts of the battery to the +&- of this same charger (somehow i dissasembled the plug of that charger and it became more "comfortable" to get in touch to the pinouts of the specific cingular's battery)
that unordinar way i did discovered that i can charge these batteries even not sure how much appropriate that other brand wall charger is. It seems its pretty much the same as a power characteristics.
Meanwhile (as i dont use this phone) i had some free time to search the net and to have better idea about that strange unordinar power charging matter with that model of a phone. The situation is that i cant find a place nearby me to buy a cheap usb and wall charger and become using this nice device finaly.
And also i dont want to buy these cable things before clearly understand why this happens ..
I did try also to charge this phone with a HTC brand wall charger but no sucsess again cause it seems this wall charger is for other htc phone (even same mini usb plug and same characteristics)
What i need is to have answers by someone very informed about that matter and let me know what exactly is the specific power charging matter (need explanations i mean) with this phone. If sharing some good ideas about how to remake others usb cable or wall charger for geting it work along for me in such a case , i will appreciate this very much
thanks
charge
hi ! please forgive me for my bad english! in this case you can charge your phone in 1 way! you need to procure a motorola or any charger with same socket but attention the charger must have 6 volts and no less than 500 mAh(milli amps)! you cut the wires and one wire put on the + of the battery you will see the signs on the battery an one wire at the - no matter which one. and you need stay with the wires 3 - 4 minutes on the battery ! then you put the battery on the phone it will start and then you cand fully charge it with the usb cable ! good luckk ! i hope my inf will help you!
no
no it doesnt work that way.
what i need is the simple answer : what is so special into the pinouts of htc cingular 8125 wall charger?
thats what i need only. Then I might figure out how to proceed
Thanks anyway
I don't know if anyone else has had trouble doing what I have done, but I've got the Cingular 8125 (HTC Wizard 100), which is also known as the HTC 8125.
1. I bought a car charger at a convenience store for $6 that had the mini-USB plug. It worked like a charm. Never any problem there.
2. I also bought a standard USB to mini-USB cable from the local computer store, because I had lost mine, and it also worked fine for both synchronization and for charging.
3. I bought a second wall charger, buying a standard mini-USB wall charger sold pretty much everywhere cellular phone chargers are sold. It's a common charging port, and this generic worked for me as well.
I'd be interested to hear if anyone has had problems with these types of devices not properly charging the unit.
Even my USB cable for my portable USB hard drive will power my unit.
EDIT: About your problem with it not charging. I had that problem about a year ago, when my battery got extremely old. It wouldn't charge even with the original charger. I just needed a new battery. The batteries get old and stop taking a charge after a certain amount of use. How long this takes depends on how heavily the batteries are used. They, like car batteries, do not last forever.
I had this problem when I had my wiz too. The battery died and drained, and my phone refused to charge it. I took it to an AT&T service center, and they had no clue what the problem was, and they wanted to issue me a replacement (it was a G4, I had a G3, I wasn't about to fiddle with that at the time.) So I asked to borrow a demo device they had there to fix it. I charged my battery on their demo device no problem, got it up to 3%, and finished charging it through my USB cable in the car socket.
It appears to be a sort of one-in-every-few-or-so type condition, but I got hit with it.
seems like noone can tell me if something special inside the mini-USB plug.
i realy cant charge. Very nice device, but i cant make it charging up whit cables.
guys, from up there, say that nothing special about the charging cables, but i trust what i see not what i read.
Perhaps there is a problem with your USB port on the device? USB charging has standards, and all devices that need power from a USB port have the same power pin configuration. Otherwise, they can't call it a USB connection. It would have to be called a proprietary connection, and they would have to change the plug size/dimensions and pins.
If there isn't a problem with your battery (which is the most likely source of your problem), then it may be a loose connection on your USB connector. This happens with a number of devices.
If a sync cable connects to the PC but will not charge the battery, then you definitely have an unusual pin detachment of some sort, or a bad battery.
thanks again..
for pity i was writing a lot to make my recent post and finaly it desapeared cause my session was left.. its funny in some case, but now i just dont want to repeat all what was intended to be posted
i give only the link where you might see why i was assuming that this is a kind of a special matter here with that htc 8125 charging
//pinouts.ru/CellularPhones-A-N/razrv3_charger_pinout.shtml
so, any more help will be appreciated a lot
thanks
SOLVED: HTC Wizard (Cingular 8125) Dead Battery Wont Charge
Dozzen said:
hi ! please forgive me for my bad english! in this case you can charge your phone in 1 way! you need to procure a motorola or any charger with same socket but attention the charger must have 6 volts and no less than 500 mAh(milli amps)! you cut the wires and one wire put on the + of the battery you will see the signs on the battery an one wire at the - no matter which one. and you need stay with the wires 3 - 4 minutes on the battery ! then you put the battery on the phone it will start and then you cand fully charge it with the usb cable ! good luckk ! i hope my inf will help you!
Click to expand...
Click to collapse
Hi - Too bad for the OP that asked questions but did not listen to this brilliant post.
I have confirmed that a variation of this method works perfectly! I have an old Cingular 8125 that I have been trying to charge for over a year using various USB chargers and NONE would charge the device.
The reason that this may happen is that the original charger has an output of 1 full amp which is much higher than most chargers. The voltage is the same but you need a charger that can handle such a strong current draw.
Nearly all USB chargers can only handle around 250milliamps - 500milliamps which is about half the power needed to breathe life into a fully discharged battery.
The best solution is to NEVER let the battery fully discharge.
Here are the details of what I did:
1. Find the best match charger of 5-6 DC Volts and ability to put out as close to one amp (1000mA) as possible. I chose an old Sanyo SCP-07ADT that is rated at DC 5.4V at 800mA. The plug can be any type, no need to be USB.
2. Cut the connector off the end of the cable and strip the outer black part up about an inch and then strip the positive and negative (red / black respectively) wires up about a millimeter, just enough to have bare metal ends to touch to a small area.
3. Take your battery out of the phone, look at the back of battery for the + and - marks which correlate to one of the metal connection points on your battery, this is where you will "touch" or "attach" the bare ends of the wires.
4. Plug the charger in making sure not to short your bare leads. Before you do this double check that the OUTPUT of your charger is indeed DC voltage so that you don't hurt yourself. You do not want AC output and it can be dangerous.
Then touch the bare end of the red wire to positive of battery, and black wire to negative terminal of your battery. I held them with my fingers while surfing the web for about five or ten minutes. I had no idea if anything was happening or not but it "felt" like the battery might have gotten just a bit warmer.
5. Unplug the home-made bare wire charger and put battery in your phone. Quickly attach a USB charger or just plug into a USB cable of your computer. I pushed it in and nothing happened at first but finally I heard the standard "bleep" when you plug a USB device in. I knew that I made progress because it never beeped before it took about 30 seconds and several "bleeps" of connecting/disconnecting from USB but eventually the charge light stayed on!
It's been about 30 minutes and I'm up to about 50% charge and been using the phone heavily while charging.
So, in summary... never let your battery discharge below 5% or you can only charge it with an OEM cable rated at 1amp (rare). IF you let it discharge to "dead" then charge for 5-10 minutes with the "wire" method and then charge normally!
Thanks to Dozzen for the original idea!!
Wizard that won't charge
When my Wizard/HTC 8125 goes dead my cure for the battery is to use a 9 volt charger with the wires stripped back also. But, my method is a bit different. I place a standard Christmas Tree light bulb (the newer small ones)in series with the charger wires. Observe the correct polarity. The battery is labeled + and - so that part is easy. By using the small light bulb you are doing 2 things. 1.You can see the slight glow from the bulb and know that proper connection is made. 2. You are limiting the charging current to the battery.
If you get really creative like I did you can solder a couple of small nails or in my case a set of red and black probes to the setup and the points on these nails/probes make for much easier connections. Note.... This method may take a few minutes longer but, is much easier on the battery.
In my experience once the battery is below a certain level NO charger that I plug in will work. I just purchased a used 8125 from eBay and brought it back to life most successfully with this method.
hy there my htc wizard battery whos dead so i charched with a cable with + and - the phone starts but when i try to connect to a usb or a adaptor it doesnt charge anymore it show me the charge icon on the baterry but it doesnt charge the usb works fine it's sync to my pc but it doesnt charge anymore... what sould i do?
So it seems no one touched on what really matters here.
A design flaw, in my opinion. The HTC Wizard cannot recharge via USB unless there is enough power to turn on. The reason is because it requires the OS to charge.
So, what many people already posted are very creative ways to charge your 8125. The easiest and cheapest way, in my opinion, is to use AA batteries.
1) Take two AA batteries and tape together so they are in series. Imagine it like this... [- AA battery #1 +][- AA battery #2 +]
2) Use two wires and tape one to each side of the AA's (one on the + side and another on the other battery's - side since the - of the first battery is connected to the + of the second).
--w-i-r-e--[- AA battery #1 +][- AA battery #2 +]--w-i-r-e--
3) Connect the positive (+) wire to the positive (+) side of the phone. By this I mean the 6 metal pieces that stick out to contact the phone battery. I did it by wrapping the wire around the top most one (or second top most, it's been over a year since I've done this.).
4) Connect the negative (-) wire to the negative (-) side of the phone. Again, bottom most or second bottom most (see #3).
5) Insert phone battery while the wires are still in and connected to the two AAs.
6) Let the power flow for 30 seconds or so and then try turning your phone on. This part is the important part because you cannot use a USB to mini-USB connected to your computer to charge the phone unless the operating system can function. Meaning, it needs to be turned on first.
7) Once the phone is on, plug in the mini-USB part and connect it to a computer. I'd recommend getting at least 5% battery before disconnecting the AAs, seeing as you need to be able to start up your phone long enough for the OS to boot. Once the OS boots, you can fully charge it through a normal USB to mini-USB connection on any computer.
old post but just wanted to say thanks. Used the wire to battery method and got phone turned on after 2 mins of holding wires to battery.