Hi,
when I connect my wizard to aux-in in my car (via headhone jack), when I receive a call, the other person cannot hear me. I have to pull out the cable and then put it in again and then it is ok.
Any ideas?
Tnx
P.S. its G4 and I have tried a lot of roms
it's a hardware thing
the connector was ment for headsets with mic and earphones
and when connected mic and speaker in the device itself is always disabled
only thing you can do is to connect an ext mic using the same connector as
the car stereo as thats the only mic input the phone will respond to
when the cable is connected
thanks for answer.
Ill try what you suggested.
Related
Hi,
I have connected my KJam to my car stereo via a cable from the 2.5mm jack to the aux port of my car stereo. Tom Tom voice and phone calls are routed through my car stereo. Sometimes, the microphone will not work when I take a call. I can hear the caller perfectly but they can't hear me. Other times, the phone functionality works perfectly and we can both hear each other great.
If anyone can suggest any ideas, I would be very grateful.
Thanks
if your using a jack to connect it to your car, then its will prob. stop the mic working as its routing the audio to you car in the same way the headset with mic that you got with the k-jam does. I had this problem on mine, but due to the fact that i use a bluetooth neadset in the car fixed that little problem 8)
That's the end of my k-jam desires then.
I use my MDA compact in the same way you describe, for TomTom, Hands free calling and to play my music through.... and my microphone works fine with the headphone jack in.
I guess one thing to check would be the number of rings on your 2.5mm jack. If you have 3 then theres a possibility the k-jam thinks you have a mic on the end of the wire. If you have 2 rings (normal stereo headphones) then there must be another issue somewhere.
thanks for your replies. My concern was around the fact that sometimes the microphone works and sometimes not. I wonder if there is a workaround or a specific type of cable that I need to ensure that only the audio is routed and not the mic as well.
Thanks for all your help.l
never tried this myself, so i can only assume it would work. you could hack a cheap wired headset up, removing the earpieces but leaving the microphone. then add a stereo 3.5 plug so you can hook it up to your car stereo.
SpeedN
I have that very problem also, it's gotten that annoying that i've stopped using it through my stereo. you are able to get around it by popping the cable out of the kjam, then putting it back in.
pain in the ass though none the less.
What is the phone is set to Speakerphone ?
Even though Speakerphone is currently not working...
Hey all,
Just wondering if anyone has had any success in fixing this problem? I am having the same issue. I have a 2 ring 2.5-3.5mm adapter connected (so it should only be routing the audio, not the mic) and sometimes the caller can hear me, sometimes not. At one stage I found by unplugging the cable, setting to speakerphone, then unsetting speakerphone and plugging the cable back in would get it to work, but not anymore...
Any ideas?!?! I love my XDAII mini but this is driving me up the wall!
Cheers,
jlitjens
Hi all
I have a MDA compact which I wish to connect to my car stereo as a handsfree unit. I have an auxiliary input for my stereo.
Is it possible just to purchase a 2.5 to 3.5mm lead for this? I have a gut feeling the mic won't work - please help? Is it possible to buy such a lead with a built in mic?
Thanks
Carl
Hi, I used to have a XDAII which I connected to the auxillary port on my car stereo, just like you suggest. It worked perfectly. When using the phone, the caller's voice woudl come out of the car speakers and the mic was powerful enough to pick up my voice even though the unit was mounted on my windscreen.
Unfortuntely, both the Wizard and the Exec automatically disable the mic when you plug into the headphone socket. Not sure about the MDA comact. Sorry couldn't offer more advice on your particular device, but I hope my experiences help.
monster said:
Unfortuntely, both the Wizard and the Exec automatically disable the mic when you plug into the headphone socket. Not sure about the MDA comact.
Click to expand...
Click to collapse
I do have the same setup. I can confirm U the mic still work after U plug in the adapter but I normally use a BT headset when I am in the car.
OK, so I assume that if I purchase a 2.5mm to 3.5mm lead, the mic should work?
carlreader said:
OK, so I assume that if I purchase a 2.5mm to 3.5mm lead, the mic should work?
Click to expand...
Click to collapse
Yes. 8)
OK - did some work on this.
I decided to cut the earplugs off of the supplied headset, and attach a 3.5mm socket.
I now have a custom XDA mini lead
All works, however volume from car stereo speakers is extremely low. Any ideas? (Yes, I have checked car volume, phone volume and headphone volume!)
Cheers
Carl
jackleung said:
monster said:
Unfortuntely, both the Wizard and the Exec automatically disable the mic when you plug into the headphone socket. Not sure about the MDA comact.
Click to expand...
Click to collapse
I do have the same setup. I can confirm U the mic still work after U plug in the adapter but I normally use a BT headset when I am in the car.
Click to expand...
Click to collapse
Hi Jackleung, my mic is being diabled, and i am beginning to think that I may not have the right connector. I have a standard 3.5mm connecting the exec. Can you let me know how you have wired your device with the type of connector? You may be able to solve a longstanding problem of mine.
Thanks in advance.
I found my mic was cancelled with the Mini, hence the custom cable.
hope this helps!
monster said:
Hi Jackleung, my mic is being diabled, and i am beginning to think that I may not have the right connector. I have a standard 3.5mm connecting the exec. Can you let me know how you have wired your device with the type of connector? You may be able to solve a longstanding problem of mine.
Thanks in advance.
Click to expand...
Click to collapse
I think my adapter is just a standard 2.5mm to 3.5mm converter. I tried 2 different adapter (one from Radio shack and the other one from ebay: http://cgi.ebay.com/USB-CABLE-headp...ryZ15040QQssPageNameZWD1VQQrdZ1QQcmdZViewItem)
Both are working for me (I will try again today and confirm U tomorrow), therefore I think yr problem is in the exec hardware itself.
To Carl,
Yr setup will not work since yr supplied headset adapter has at least 4 connection on the plug compare to 3 on the standard one. The extra connection is for the mic. If U cut the wire like this:
<---- X --- mic+volumn control ------ ear plugs
Then U can no longer use the mic w/ the custom wire. But if U:
<------- mic+volumn control -- X ---- ear plugs
then the mic on yr mic+volumn control will pick up the voice
hi jackleung
Thanks for the reply - the lead was cut after the mic but before the earphones.
This was because a standard lead with a 2.5 / 3.5mm adaptor didnt work.
My only issue now is the low volume!
Cheers
Carl
I tried it on my Imate Jam again. My mic on the Jam still works (eg: Voice Command via Cyberon Voice Dial. So do phone conversation) even I use my 2.5mm/3.5mm adapter to connection it to my car stereo.
Hi,
I did the same for me and a friend of mine with a Univer..er - Jasjar and connected this to an FM transmitter - We have excellent sound quality, volume and the you can still answer calls by pressing the Mic Button
Frikkie
(If you are gonna be late - dont rush, else someone else and YOU will be cross)
check connections?
I have done exactly what you did, put a 3.5mm socket on the end of the included handsfree cable.. volume is fine, and i regularly connect it to the aux in the car, and multiple sets of headphone/speakers...
The best suggestion to your volume problem is to try again.. i know i had issue with the stereo channels getting screwed up (and even combined at one point) and it was just trial and error getting the connections clean..
You have to ensure that both the shaft and tip connectors on the socket are grounded to the shared ground on the circuit board.. otherwise the audio will probably be less than perfect.. check for dodgy soldering/connection.. coz i can assure you that your theory does work!
Dan
There is another topic on this here.
The person from there uses:
http://www.expansys-usa.com/product.asp?code=PPCPADPT02
which has two 3.5mm plugs.
Description: It has a 2.5mm plug at one end (this plugs into the PocketPC) and two 3.5mm sockets at the other end (into which you plug your 3.5mm headset or headphones).
My question was: could I put a standard 3.5 car kit mic into this 3.5 headset jack (the one with the mic)? Would the mic work if I plug it into a headset jack?
I assume the other one (headphones = stereo only) I will plug it directly into my car auxiliary via a 3.5mm to RCA cable, right?
is there any way to enable build-in microphone while using 2.5mm audio jack connected to car's stereo?any registry edit?Thanks in advance!
I think that the insertion of a jack into the socket operates a hardware switch so I don't think there can be any software tweaks. It is the same as plugging headphones in to a radio etc. the insertion of the jack breaks the connection to the speakers and diverts the output to the headphones.
I got a 2.5mm 4pole male to 3.5mm 3pole female adapter with built in mic and volume control off ebay for less than £5. A cheap 3.5mm patch lead to car stereo later and it works perfectly, other than a slight alternator induced whine is audiable when charging. This is more likely to be from my cheap car charger as it goes when not charging. I like the way MP3s etc get muted when a call comes in. TomTom, Mortplayer and phone calls all at the same time, I love my Wizard.
Guess u didn’t try it. I have my wizard attached with the car stereo and when I get a call i can receive it and talk, the mic gets activated auto. Works perfect for me. Give it a try should work for u.
didn't try what?how does your mic work?
Well I use a 2.5 to 3.5 mm converter which in connected via RC wire to the car stereo linein, when I get a call I just receive it and I can talk. The music stops I can hear the person call and can talk back, the microphone works perfect.
with mine 2.5->3.5 mm jack(done it myself, the 2.5mm jack has 3 poles, not 4) can only hear but the other person doesn,t hear me
my jack has 3 poles, bougth it from ebay some time back, works perfect for me
i have the following problem: when i plug my wizard to my car stereo via 2.5mm stereojack cable the build-in mic stops working so i can't talk using the cars stereo...is there any reg-edit or program that can allow the built-in mic to work while the cable (or any handsfree) is inserted? i read somewhere that there were people that have their cables plug but still the mic is running...can you tell me if your jack has 3 poles or 4 poles? thanks in advance!
help please [;
i'd rather say it's a hardware problem. in most headset jack sockets i've encountered it's done by a jack plug simply unpluggin' built in speaker/mic due to the design of the socket. of course i may be wrong, nut i'd say registry has nothing to it...
i think as you do, but someone mentioned on another post that he puts the cable and the built in mic continues to work.
Hi everyone,
I'm wondering if it's possible to have built-in mic active when a cable is plugged into the 3.5 mmjack. For example...I connect the hd2 to the car stereo and if I get a call i need to disconnect the cable because the built-in mic is inactive.
venz111 said:
Hi everyone,
I'm wondering if it's possible to have built-in mic active when a cable is plugged into the 3.5 mmjack. For example...I connect the hd2 to the car stereo and if I get a call i need to disconnect the cable because the built-in mic is inactive.
Click to expand...
Click to collapse
Mine works when I plug mine into my car with a standard 3.5mm stereo cable.
Does the cable you're using have 1 or 2 black stripes on the plug?
i agree, this feature was one of the most pleasant surprises for me with the HD2.
on my kaiser, i used a special HTC headset that had an inline microphone (which i snapped on to my shirt collar) and this headset allowed me to plug in a standard 3.5mm stereo jack, which my car audio was plugged in to. this was the best solution at the time for the kaiser that allowed me to keep all cables connected and be able to use the car's speakers and have a working microphone all at once.
but with the HD2...WOW!!! i plugged in my car stereo's 3.5mm stereo jack straight into the HD2 and put on some music and started driving. a call came in while driving and i just pressed answer because i was still used to my kaiser set up (i had owned the HD2 for less than 24 hours at this point so wasn't quite used to it yet).
i started hearing the other party and i started speaking. and the other party could hear me. and THEN it hit me...i was like, holy hell!!!...what am i speaking in to? how come the other party can hear me?
great features, great phone!
rp-x1 said:
Mine works when I plug mine into my car with a standard 3.5mm stereo cable.
Does the cable you're using have 1 or 2 black stripes on the plug?
Click to expand...
Click to collapse
I think it has two stripes since it's a stereo jack. I'm not sure but i think initialy I was able to speak in the car with the leo plugged into the stereo. May be some app I've installed later changed something?!?
the built in mic will stay active unless u have a cable with 4 connections (3 rings on the plug), a regular stereo cable has 2 rings. I've been using this type of setup for a couple of years with my previous phone, a.k.a. iphone. The mic is pretty sensitive and can pick up your voice rather well. I have my hd2 clipped to my sunvisor for easy access and routed the wiring inside the windshield molding down under the dashboard to the stereo and it works pretty good.
http://www.youtube.com/watch?v=osLFRLL7qOw