Database Users

new rom made my jasjar a brick :(

I used the new rom from i-mate JASJAR_WWE_13076_164_10900_wwe_ship, it gave me an error message error 116, i followed instructions to recover, no use, i cannot even hard reset any more (it gives me the white screen, and when i press 0, it just goes back to be switched off).
I am going to put back the previous rom if it works...
anyone had this problem? any suggestion how to solve it?
help much appreciated
Nabil

Can u put back on bootloader menu?
In my upgrade it did the same, but it could go to bootlader... then i tryed to flash it again and it worked ok.

bootloader how?
I only get a white screen when i hard resest with x and 0 option...
how do i get to bootloader?
help much appreciated

Reset (stylus) + Power + Light
A thing like that

Bootloader mode: Hold light and power buttons together and reset with stilus.

i get the usb bootloader message
thanx for the tip...
i get the message on the device upgrading the radio stack, so i have access to the bootlaoder, then i get an error message on the pc side...
so i made progress, but still not working to completion

started working at third attempt
hope it works thanx a million dude u really rock!

steps
Since this helped me, I will write the procedure again here:
You need to have access to the bootloader.
Connect the jasjar to pc usb
Access bootloader
To do that u press together the power button and the light button (light button is 3rd button in the front) and reset button (with stylus), u might need to put stylus in mouth to do that as it is a bit fiddly.
The screen will be dark but if u use flash light on it u can see usb written on the screen
Then start the upgrade from PC, u might need to try all of this a few times, it took me three attempts to get the upgrade started
You will also be able to see the message upgrade in progress on the jasjar screen which will be still dark.
Nabil out

Glad that your universal is up.
:lol:

Help help please stuck on bootloader

Help Help Help
Iam new to the flashing
I have herald (HTC P430 HERA) with wm5 ,i tried to upgrade to wm6 with TOUCH-IT.I installed the SPL and then ran the RUU ,everything was perfect the installation started normally ,durin the installation i chose the option to use the keylock ,when my htc started it kept on asking me the password on the device which i entered but it did not accepted .i kept on trying and eventually took out the battery.When i restarted the device it got stuck on a green scnreen with spl 1.08.0001 and when turned off i tried going in to the bootloader but everytime i run the same ruu it gives me erorr 300 i have tried several times now, donwloaded each and every ruu but all in vain and im in pain .sometime the screen get stuck on 0% . Can somebody help or atleast direct me to the right area.

at least it we could reach 1% rom update can be done
i think we can handle it via bootloader commands

you need to install enablerapi....
.......................

You have to download the official Tmobile RUU (google it), and reinstall it. After that before you try to flash your phone you have to take the Enablerapi cab and put it on your phone. After that do a hard reset. If you dont know what that is by now you shouldnt be flashing your phone. But anyway hold the buttons above the talk and end buttons and press the reset button at the same time. A black screen will come up and ask you to press the talk button (green button), press it and the phone will do a reset. Configure your screen and connect phone to active sync/WMDC and make sure you put the phone in airplane mode. Then run the uspl again and follow the directions on the screen.

How to kick out X1i out of bootloader mode?

Hello.
One xperia entered tricolor screen (volume down + powering on) but now it cannot leave that screen, even if the battery is taken out for a minute.
Is there a way to kick the xperia out of bootloader mode?
Thanks.

when you take the battery cover out you should see a hole, insert the stylus in it and "push".
enjoy.

Thanks a lot.
I hope you don't mind, but since these devices are not the cheapest phones out there and you have 3 posts and just joined... I'll wait for some one else to confirm.
Thanks a lot anyway!
Any one can confirm?

I do mind and I hope it breaks on you and becomes nonusable ever again

celinelust said:
I do mind and I hope it breaks on you and becomes nonusable ever again
Click to expand...
Click to collapse
Not nice...

That action is to soft reset only not to enter bootloader (normally u need more then a few key combi to enter just like manual hard reset)

Hello.
Any one that can help?
I tried the 'reset' button but of course that didn't help.
I tried hard reset and it showed it was hard reseting, but after than the same tricolor screen appears.
It says in this order:
RUUNBH (aligned right)
KOVS110
SPL-0.72.0000
MicroP1-787
MicroP2-707 (these last 4, aligned left)
Upgrade ROM Code Error (centered)
Please try again (centered)
Serial (centered)

I tried also RUU with hardspl, and RUU with ruu_signed.nbh (supposedly UK official rom).
In both cases it goes to withe screen with the progress bar at 0% but stays there until you take off batery, then it returns to previosly mentioned tri-color screen.
HELP please!

[Q] HTC Touch HD problem !

Hello guys.. well i have a Blackstone HTC Touch HD..
I've got a big problem !
The htc wont start ! Nothing happens when i push the on/off button..
When i put in the charger.. the orange light turns on for some seconds.. then it turns off.. and then the phone turns on.. it shows "Smart Mobility" and vibrates..
Then it restarts.. and shows it again.. and again..
It keeps doing that..
What is the problem ? Can i solve this ?
Thanks !

YouBou1992 said:
Hello guys.. well i have a Blackstone HTC Touch HD..
I've got a big problem !
The htc wont start ! Nothing happens when i push the on/off button..
When i put in the charger.. the orange light turns on for some seconds.. then it turns off.. and then the phone turns on.. it shows "Smart Mobility" and vibrates..
Then it restarts.. and shows it again.. and again..
It keeps doing that..
What is the problem ? Can i solve this ?
Click to expand...
Click to collapse
Is this a new device? Have you recently flashed any new roms/software onto device?
If I where you I'd try a hard reset. To hard reset device:
1. Turn off device
2. Hold down vol up & vol down
3. Continue to hold down vol up & vol down and press power on button at top of HD
4. You will be presented qith a white screen & blue text
5. Follow instruction and restore factory settings (Hard reset) by pressing vol up.
If this doesn't work and device is still playing up and its a new device without any new rom/software on it I'd return it and get a replacement. The alternative would be to flash a new rom on it, but if its faulty device from start I wouldn't recommend this and I'd return it.

Fallen Spartan said:
Is this a new device? Have you recently flashed any new roms/software onto device?
If I where you I'd try a hard reset. To hard reset device:
1. Turn off device
2. Hold down vol up & vol down
3. Continue to hold down vol up & vol down and press power on button at top of HD
4. You will be presented qith a white screen & blue text
5. Follow instruction and restore factory settings (Hard reset) by pressing vol up.
If this doesn't work and device is still playing up and its a new device without any new rom/software on it I'd return it and get a replacement. The alternative would be to flash a new rom on it, but if its faulty device from start I wouldn't recommend this and I'd return it.
Click to expand...
Click to collapse
its new yeah.. after hard reset it still doesnt work
in bootloader it says : BLAC100 32M
SPL-1.14.0000
MicroP-BlackStone (LED) v6
i just fount the mobile somewhere

YouBou1992 said:
its new yeah.. after hard reset it still doesnt work
in bootloader it says : BLAC100 32M
SPL-1.14.0000
MicroP-BlackStone (LED) v6
i just fount the mobile somewhere
Click to expand...
Click to collapse
TC,
You lost me right there. Did you just say you FOUND the mobile somewhere!?
Cheers.

YouBou1992 said:
its new yeah.. after hard reset it still doesnt work
in bootloader it says : BLAC100 32M
SPL-1.14.0000
MicroP-BlackStone (LED) v6
i just fount the mobile somewhere
Click to expand...
Click to collapse
Ah, so you just found the device and decided to keep it...LOL
Well seeing as you can get it into bootloader, you are able to flash new roms onto device. All you need to do is follow guide in my signature.
The only other options would be to return it under insurances/warranty. But seeing as both are unavailable to you as phone isn't yours.............. If I was you I'd return device anyway and maybe the rightful owner may show some gratitude and give you an award!!
Choice is yours!!!
EDIT
You may also find that the orginal owner has put a phone lock on device rendering phone useless anyway unless you know security code. I have similar lock on mine. If this is the case, be kind enough to return it to rightful owner!!

[Q] can't startup the screen and not even notification light while charging. PLZ HELP

hey can anyone help me out in this problem. PLZ
I hv hd2 from pairs. i had use Android 4.0.1 in that, but when i tried to update my phone with 4.1.0 the screen comes with plain white and doesn't do anything. after some research i got to kn that i should run HSPL4. But when i tried to do so, after flashing hspl v3. somthing the screen wont open. when i start my phone it vibrates for once but dose not start the screen also can't go in boot loader while pressing vol "-" button with power on button.
plz somebody help me to get out of this problem. Its freeing me out.

Yours phone is dead like mine..somebody says its dead motherboard, someone says phone must go on JTAG BOX but its to expensive!