Related
Hello everibody,
I have an annoying problem: my Qtek sometimes prevents waking up! And only a soft reset can power it on!!!
But the crappiest thing, is that the device doesn't power on when it's cold! I have tested it!!! :shock:
PLZ HELP
It's an hardware prob? It's better to send it to repair? Thx
Oh, another thing :twisted: when the device is power off (and I can't power it on) the green led is still acting like normal, it even stops when no coverage is present. If I try to call to the S100, it rings but I can't do nothing? :?
Great forum, anyway. I have solved nearly ALL of my Qtek probs.
I will add these infos:
ROM: 1.06.04 ITA
RADIO: 1.05.00
Note: I have already tried with an Hard Reset. Nothing resolved. The device simply won't power up when it's below 20° C. And I don't know why.
Your Magician seems to be a candidate for the repair shop of for an exchange. Never heard about a problem like yours
Cheers
Uff... Nobody (except me) have this prob? Can someone try this? Before sending it to repairing, I would figure this s**t out! And maybe find a valid solution...
AND: How can I do the BigStorage trick on my ITA ROM? I know how, but with the other languages... Don't want a foreign ROM only for 20+MB...
I think upgrading the ROM can't change anything, if it's an hardware problem... I want an active device in this winter, cannot reset it all the time!
Possible Solution?
Yet nobody seems to have my prob. But before sending my S100 to the pocket pc heaven, I will explain a possible scenario. I've read that cold can reduce the battery charge dramatically. So what I am thinking:
1) The unit is absolutely normal when warm.
2) When the unit is cold, is STILL normal.
3) When I shut down the unit, the LED is STILL blinking.
4) But then -what the hell- it seems CAN'T turn it to the active status.
5) The only thing that I can do is to RESET the unit. Then when I control the battery status is ALL ok: same level as before. But there isn't the missed calls of who have called me when the unit is in this state!
I think that the low temperature affects the internal battery, reducing it to zero. When the S100 is on this effect couldn't be noticed, because the external battery constantly charges the the internal one. But the charge is not provided when in standby. And so the charge in the internal battery drains... making impossible to turn on the device! But when resetting, the external battery is give power to the internal one, and the device is now fully functional as before.
According to this mess, then I only need to replace the internal battery with anything better, and the device MUST work EVEN if cold...
Now I would like to listen to others, just to convalidate this theory...
Otherwise, the device will make a good and comfortable travel to the repairing center, hoping they will send me a completely new one ( I have accidentally scrachted it one time. And another.)
Hope that you will understand my Huff-Puff post. Hope that someone will see this post.
Cheers,
MocciJ
Yet no replies...
This damn thing has taked too time, and so I'm sending the device to the centre tomorrow...
I've tried to upgrade my old qtek rom to the 1.11 of the I-mate: nothing resolved...
Is it ok to send a device with an imate rom to a qtek centre? Lemme know...
my friend has same problem, I flash radio whit 1.13, 1.12 (rom is 1.12)
I shell open it ....
Click here to read of a similar problem
As far as sending your phone back, which judging by your signature you already have, you need an official rom to be installed if you want it covered by warranty. Not sure on Qtek's policies. Have you sent it yet? What did they say about your Jam rom?
Don't try to make the same thing I did. When try to changing to ANOTHER Rom Manufacturer to see if the problem vanish, remember (at least before sending it) to PUT THE ORIGINAL ROM IN IT!
THEY (AT REPAIRING CENTER) WILL SAY THAT THE SOFT IS CORRUPTED!
This way I avoided my warranty. Hope this info will help.
I'm deciding what to make now. Do I have to pay for this prob, or do I cover my qtek with warm clothes?
Or better find a solution?
If anyone has suggestions, I'm glad to listen. I want my pda back (it stayed out for a month, I miss it!).
Do not make hazardous moves with ur pda when it's in warranty. Or U will pay that the double it's price!
Don't try to make the same thing I did. When try to changing to ANOTHER Rom Manufacturer to see if the problem vanish, remember (at least before sending it) to PUT THE ORIGINAL ROM IN IT!
THEY (AT REPAIRING CENTER) WILL SAY THAT THE SOFT IS CORRUPTED!
This way I avoided my warranty. Hope this info will help.
I'm deciding what to make now. Do I have to pay for this prob, or do I cover my qtek with warm clothes?
Or better find a solution?
If anyone has suggestions, I'm glad to listen. I want my pda back (it stayed out for a month, I miss it!).
Do not make hazardous moves with ur pda when it's in warranty. Or U will pay that the double it's price!
Is there any way you can take it to another repair shop? If I had your problem, ie turning it in with a wrong ROM and being rejected, I would just reflash and drive to another city to have it fixed. They would never know the difference.
If that isn't an option in your country, I guess you will have to pay for the repair, even though it is very unfair, because a 'wrong' ROM can't be the cause of this problem
Thx for this suggestion. Currently I have an Qtek rom perfectly working. But they delivered my Qtek to French for repairing (and I am from Italy), guessing that I haven't that option.
The only thing that I can do to riesumate my warranty is to declare that that rom is OK, downloaded from an official site. The cause is that when the Qtek hasn't made upgraded roms, the imate did. In case, I will say that the problem was there EVEN before the upgrade (it did).
There is currently NO SOLUTION to this problem (it's an hardware problem, and should be repaired by the repairing center -of course-)
-----
I will report what the World Startel Communication (the repairing center) has said (transcribed from italian to english):
1)The product is in delivering phase.
2)The product resulted to be irreparable. It will delivered back.
3)The repairing service has resulted to be out of warranty. We are waiting the consumer to pay the reparation (They said they sent me the price. Currently they seemed to haven't sent nothing).
4)The product has come to our labs.
5)The requested reparation is inserted in our knowledge system.
And that is. The Qtek has delivered, considered irreparable, and when out of warranty is ok for repairing? That's something odd... Considering that I've retrieved how to reach the tracking service only by calling the operator... Now that the S100 is in their labs, they say that the prob is in their knowledge system, which I ignore what it means. Now I suppose that the product reached French before checking the warranty, and this would be to pay something around 10-20€, IF I decide to not repairing the unit...
Ok, that's all. Hoping that this winter isn't getting cold.
Cheers,
MocciJ
Ok, the S100 is in repairing again. They will send me repaired with a price of 50€.
Hope that they will explain me what happened. Otherwise, sending it seems to be the only solution avaible.
They will raise up my warranty, almost that's what I've heard.
So this can be the end of the topic...
Cheers,
MocciJ
They are sending it back, but non-repaired. No cost, but nor warranty at all. They SIMPLY deleted my warranty taking it for 2 months.
Now, what's the real mess with the warranty? Oh yes, the ROM was changed from Qtek to an Imate one, official. They find out that there's a mix between these 2 software, and that they CAN'T upgrade or downgrade it at well: is this possible? Incredible!
They "sincerely" said that changing ROM required a new motherboard, which cost the godness of 200+€... Exactly half the original S100 cost!
QTEK CUSTOMER SERVICE SUCKS! LONG TIME WAITING! NONE REGARDING OF THE CUSTOMER!
Now that my S100 is out from it's warranty, we'll return on how to resolve this TINY, LITTLE prob...
Do we have to cover our Magician with warm clothes? Just let me know your ideas...
Best Regards,
MocciJ
I have a tmobile wing and I had it for awhile but just started using it again recently but when i put my sim card in the phone and turn it on it just keeps saying Searching...
I get service for like 2 minutes then it would just go away. This would happen when I leave the sim in the phone, it would get service once in awhile, like for 2mins every 2-3 hours, but never consistently.
My sim card works perfectly on other phones and when i insert a friends sim card into the wing it still has the same problem, it keeps saying Searching... I don't think its a problem with the sim card since it works fine with other phones.
I tried soft reseting it and hard reseting it but it still seemed to have the same problem. Does anyone have any idea what the problem could be or what I can do to try and fix it?
what radio rom does your phone have and what rom are you using?
you can check your radio rom by going to settings>system>about ( i believe). If not that, then settings>system> device info.
also, if you don't know what rom you're using, it's probably the stock rom.
It might also be that the particular spot you are in is just unlucky for reception and that other phones have better reception by design.
fzzyrn said:
what radio rom does your phone have and what rom are you using?
you can check your radio rom by going to settings>system>about ( i believe). If not that, then settings>system> device info.
also, if you don't know what rom you're using, it's probably the stock rom.
It might also be that the particular spot you are in is just unlucky for reception and that other phones have better reception by design.
Click to expand...
Click to collapse
It says Radio version: 02.83.90
And i believe it is the stock rom since i never changed it or anything. and I doubt it is the area because I tried using it in several other towns.
anyone have any idea what could be wrong?
p4350
well on my p4350 over the past 2 weeks i have been receiving little signal like every 5 - 7 hours i mite get it for a bit but only for a sort time. i was wondering if it needs its radio updating?
any help?
Hi, I just want to share my story. maybe it could help you out.I had a wing for more than a year now. recently it had the same problem. it just don't have any signal at all, just keep searching. I tried what you did before. hardreset, softreset, and update the firmware. Nothing helps. since my phone is out of warranty, i can't send it to t-mobile. So i went to a local repair shop. They told me it could be hardware problem. I paid $50 to get it repair and no problem since. I don't know what they did, maybe replacing something inside. So don't just look at the software side, it could be hardware problem.
I have the exact same problem, and it's really pissing me off.
benjin89 said:
Hi, I just want to share my story. maybe it could help you out.I had a wing for more than a year now. recently it had the same problem. it just don't have any signal at all, just keep searching. I tried what you did before. hardreset, softreset, and update the firmware. Nothing helps. since my phone is out of warranty, i can't send it to t-mobile. So i went to a local repair shop. They told me it could be hardware problem. I paid $50 to get it repair and no problem since. I don't know what they did, maybe replacing something inside. So don't just look at the software side, it could be hardware problem.
Click to expand...
Click to collapse
what kind of repair shop was it?
i have my dopod 838 pro running on Schap's WM6 Pro 4.30 ROMs. it had been all right for pass 5 month since i upgrade the original WM5 to WM6. and since then i never flash it.
Yesterday afternoon, i can still use it to receive call. but at night. i found out that the phone doesn't have any signal on GSM network. when i double check it, it asking me to key in sim card password and said "unknown sim status"
if i key in the wrong password, it will state that my password is wrong. but if i key in the correct password, it still asking me for password. and stay on the same page no matter how many times i key in the password.
i already do hard reset. but the problem still exits. these were info when i start the phone.
M 05
S 04 NO GSM
B 06 D3.62
and these were info from bootloader
HERM 100
IPL-1.04
HERM100
SPL-2.10.Olipro
i very confuse with a lot of help over internet in thread for those no GSM problem. but i can't seems find any similar problem with mine.
WIFI and bluetooth were working fine. i can still goes into the Today screen and access every other things normally.
Please help me.
Do you know what Radio was on the device before the no GSM?
If you try to update your radio more than likely it won't update and freeze at a low percentage of completion. Sorry to say the radio on the motherboard is dead or dying. Happens frequently on the Hermes and the only way to fix it is to get a new motherboard. Happened on mine - would work fine then the GSM would start dropping out and reconnecting during the day. Upon reboot it would get the NO GSM message. Turn off leave battery out then try again - sometimes would start up then it would just die. After replacement of motherboard it just works.
No amount of flashing of ROMS including or not including the radio will fix it - the chipset in the HERMES is the weak link and they eventually just go. Either the solder has developed cracks from charging (heat) or flex.
Sorry.....
Wam7 said:
Do you know what Radio was on the device before the no GSM?
Click to expand...
Click to collapse
i not pretty sure . but it was original radio. i didn't flash radio before.
but i had downloaded the new version radio. successfully flashed it. but still no GSM.
STIM141: i think you are quire right. i had inquiries some shop of phone repair and have describe them my problem. since my phone die without me doing anythings to it. they pretty confirm it's the mother board die. they said the only way is to repair it and replace motherboard.
The best way to fix it cheaply is to find a donor phone thats confirmed working with a guarantee on eBay. Something that beat up, maybe the screen has problems and swap it out yourself. Its pretty easy to replace and you can do it in about 10 to 15 minutes tops. Need a couple of tools but they can be found locally. Should cost no more than about 30-35 dollars if you are patient. Next would be to scrap the phone for parts - but if the motherboard is bad you probably won't get very much unless you part it out and just wait for individual buyers.
Hello guys, I am having a problem with my unbranded x10i bought in UK (I am currently using it here in the philippines with a local sim card) . After I did an OTA two days ago, it just keeps on restarting/booting! I have tried the "repair" option twice in the PC Companion software but still no luck.
What's strange though is that when I tried switching the phone on WITHOUT a sim card in, it booted up with no problem (and I checked the build number, it says R2BA020 which probably means the OTA update was a success). I put the sim card back in and the problem came back, it kept on restarting.
What seems to be wrong? Any suggestions on fixing it? I would really appreciate your help guys. Thanks!
Update: I successfully rooted my phone hoping that rooting would solve my issue, but unfortunately it still keeps on rebooting/restarting whenever i put ANY sim card in.
Have you tried using another SIM-card?
yes. I have used different sim cards...
Try flashing back the original firmware.. and make sure the sim card is inside the x10 while doing it. Worth a try..
I have the same problem too and I have just updated my phone to R2BA024 and the firmware version is still 1.6. I have hard-reset so many times and reinstall some many times. The problem still there. I have contact Sony Ericsson customer service and bought my phone to fix. Got it back, problem hasnt been solved. I have waited for 3 weeks for a reply from them and end-up they said they do not have any new phone or spare-parts to fix my phone. Until then, I have contacted them almost 10 times and still no one has the right answer and just keep asking me to wait. They dun even have an exact date when the parts will arrive. I am very piss off now and I dunno what I should do next.
Its the same problem here with me too. Bought the phone from a friend about 3 days ago. was going all good when it just started to keep booting itself. While the sim is inside, it'll restart just as it finishes booting. Without the sim, its fine. I have tried other sim cards too, and format/reset my phone many times but it just isnt working for me anymore. HELPPPP!!!
cvg_guy said:
Hello guys, I am having a problem with my unbranded x10i bought in UK (I am currently using it here in the philippines with a local sim card) . After I did an OTA two days ago, it just keeps on restarting/booting! I have tried the "repair" option twice in the PC Companion software but still no luck.
What's strange though is that when I tried switching the phone on WITHOUT a sim card in, it booted up with no problem (and I checked the build number, it says R2BA020 which probably means the OTA update was a success). I put the sim card back in and the problem came back, it kept on restarting.
What seems to be wrong? Any suggestions on fixing it? I would really appreciate your help guys. Thanks!
Update: I successfully rooted my phone hoping that rooting would solve my issue, but unfortunately it still keeps on rebooting/restarting whenever i put ANY sim card in.
Click to expand...
Click to collapse
Is it 32K sim or 64K???
hi techguru, can u tel me wot the diff is between the 32k and 64k sim ? many thanks
ISSUE SOLVED here.
BTW : my sim is 64k.
anyways, i found out that the problem was because of the faulty battery. what i guess is that the voltage couldnt get to the requirements of the phone, and everytime the sim radio (whatever its called) switched on, the phone just turned off.
I reinstalled/repaired my phone many times, GOT the exclamation mark of death one time also, but the phone just didnt turn on.
Later i noticed that the phone would just turn on itself when i attach the phone to the charger, otherwise it wouldnt turn ON. So what i did was just change the battery, and walla, the phone is ALIVE again.
Sim is working, phone is working.
BUT i see some signal losses from time to time, otherwise the phone is good enuff.
FOR me , the change of battery did the trick, I hope it works for u guyz aswell.
Cheers ...
Shonan_ said:
hi techguru, can u tel me wot the diff is between the 32k and 64k sim ? many thanks
Click to expand...
Click to collapse
64k sims draws more power than normal ones.
Sent from my X10i using XDA App
Cheers fella this mite be worth me lookin in to
Sent from my X10i using XDA App
addictivesundew said:
ISSUE SOLVED here.
BTW : my sim is 64k.
anyways, i found out that the problem was because of the faulty battery. what i guess is that the voltage couldnt get to the requirements of the phone, and everytime the sim radio (whatever its called) switched on, the phone just turned off.
I reinstalled/repaired my phone many times, GOT the exclamation mark of death one time also, but the phone just didnt turn on.
Later i noticed that the phone would just turn on itself when i attach the phone to the charger, otherwise it wouldnt turn ON. So what i did was just change the battery, and walla, the phone is ALIVE again.
Sim is working, phone is working.
BUT i see some signal losses from time to time, otherwise the phone is good enuff.
FOR me , the change of battery did the trick, I hope it works for u guyz aswell.
Cheers ...
Click to expand...
Click to collapse
This also mite be worth a look too
Sent from my X10i using XDA App
hmmm. sounds interesting. I might try changing my battery. btw, i have tried using both 64 and 32K sim cards but the phone keeps restarting with any of the sim cards in. without both the sim cards, the phone works fine. how much does an x10 battery cost?
here, i get the cheap chinese battery. it isnt expensive, but its working great. almost better than my previous battery.
cost me around 2.5$.
but.. i am still getting lots of SIGNAL DROPS. i dont know why it is happeneing. I tried swapping the battery with the original battery of another X10, but no change. Signal loss is not a battery issue then.
Any idea what it could be ??
Signal loss?
Maybe a weak signal, or radio related?
or maybe its because i updates it to R026 is causing the signal loss issue ??
@techguru
I am also using airtel, but with a 64kb sim.
In my case it does not start.
It start if with no battery or with a 128kb sim of TIM.
I tried to recharge the firmware but nothing seemed to change.
I know that someone solved the problem swithcing off the phone in airplane mode, but this is not the case for me.
I also noticed that in some cases the led is green and is slowly blinking.
I am ready to change the battery if this helps, but I am not sure. Even if I put it under charge it does not switch on and the battery seems not to charge
As I bought the phone only since one day I wonder if they will change it.
HI
this has been some 4 days i got issue with my phone show no service or emergency call only the imei basbnad is ok
i have also flashed it with stock rom latest version but when put sim gives no service message done imei repair with z3x
but still have this problem how to get sorted this issue ? and is there anyway way via that i can check whether its hardware issue ?hoping for prompt reply.
thanks an advance .
If your IMEI was ok, then all you did is waste time with using the riffbox to rewrite it. You have a hardware problem, and it's one of two possibilities.
1. The SIM card tray is damaged.
2. The motherboard is damaged.
For your sake, let's hope that it's item 1, because the part is readily available on Amazon for 10USD plus shipping. That part is also really easy to replace. If the SIM tray isn't the culprit, then your other alternative is to replace the motherboard.