Few days ago i did that this manual (http://www.pcdemano.com/phpBB2/viewtopic.php?t=13789&postdays=0&postorder=asc&start=0) says, but something was wrong because, after reset, my alpine didn't work, even i'm not be able to get it in bootloader mode, i am very afraid about this....i need help please....
P.D:There is another way to reinstall bootloader or flash rom by other chance?
Related
lastnight when i downgrade from WM5 to WM2003SE without having sd image, i used typhoontools to flash the bootloader from the french orange rom then reinstalled the lastest Qtek 8020 rom under bootloader mode. everything seem going well.......BUT when it get to 100%, the phone restart itself, and on windows saying something like "Successfully............you may now retart your smartphone....."
after the phone restarted it go straight to the bootloader mode (3 colors screen) and i try to hard reset........it dosen't work.....
then i try to flash the rom again........same thing happen
Could anyone have any idea??? plz help me..........otherwise.........my phone will never be able to use..
many thanks in advance
lastnight when i downgrade from WM5 to WM2003SE without having sd image, i used typhoontools to flash the bootloader from the french orange rom then reinstalled the lastest Qtek 8020 rom under bootloader mode. everything seem going well.......BUT when it get to 100%, the phone restart itself, and on windows saying something like "Successfully............you may now retart your smartphone....."
after the phone restarted it go straight to the bootloader mode (3 colors screen) and i try to hard reset........it dosen't work.....
then i try to flash the rom again........same thing happen
Could anyone have any idea??? plz help me..........otherwise.........my phone will never be able to use..
many thanks in advance
you're ****ed mate.
problem solved, for those who Stuck in SPL1.xxx SPL 2.xxx after WM2005, please go to http://www.spv-developers.com/forum/showthread.php?p=3576#post3576
for how to get back to WM2003
I already try with official rom, but my herald is still brick, i can not syncronize the herald with pc to run the official rom.
It is freeze in inicial boot with HTC logo.
help, please anyone....
Try turning the phone off and then turn it back on by holding the camera and communication button. This should bring you to the boot loader screen at which time you can tehter to your pc and run the OEM RUU. That should do the trick.
[Thanks, problem resolved.
German Vodafone Herald bricked
Hello,
could anyone here give me an Original Vodafone Rom to unbrick my Herald? It must not be WM6, WM5 would be sufficient. I only want my device to alive
Or is there another way to unbrick this phone? I only can get in bootloader modus and so i can not start the phone to CID unlock so that i can flash with another ROM like HTC Original.
So Have anyone a possibility to unbrick the phone or CID unlock from bootloader?
For any idea, thanks very much.
Hello
First I am many sorry if repeat but I still not know what I can do. I buy mobile and I thing is Type 2b (still on operator logo) but I don´t know how I can find solution, because I tryed flash with many roms and I tryed latest radio rom and everything done but when is finish it restart and than is still in orange logo (or HTC and etc). and about two seconds show NO GSM.
I have SPV m3100 with SPL-1.40.Olipro.
PLEASE help me I cant find solution !!!
Many thanks and many sorry if repeat threat
Try a hard reset. You DON'T have Hard SPL on your phone. It may be unlocked but it may not be Supercid. The best idea would be to flash the original carrier rom on to it and see if that fixes it THEN flash Hard SPL on it.....
Good Luck...
Its possible you may not be able to recover your radio rom...
Hello,
Thank you, but I tryed originall shipped rom and original rom from orange site. Everythings done fine. I tryed also radio rom and it done OK. I dont know what I can do.
Please can you send me links for there roms which I can flash?
I wish I can repair.
Thank you in advance.
If the shipped rom fails you are probably looking at a permanent brick. There are some other things you can try using MTTY but it may not be hopeful. This is one of the pitfalls of buying a "bricked" phone. It may not be fixable and you spent $$$ that could've been spent more usefully elsewhere...
Hello,
thank you for reply, and how I can use there MTTY and when I start it it is like other working pda and it flash led lights, only for second, like when you flash new rom and when start and then it flash light and then screen change for "tap on screen" but here only flash and dont change screen.
Do you know what I mean?
Does it say "tap on screen to setup"?
If so you may be looking at a bung digitizer. You will need to replace the LCD to fix this.
Hello,
no, it is only like it, it stay orange logo, but when "blik" "NO GSM" it blik all display and than stay in orange logo too
Do you thing if JTAG help me?
can't say, never used. You do need some technical skill to use the Jtag method...
yes I have some technical skills but I dont have any schematic of jtag cable.
EDIT: I find some pdf with two schematics:
1. Holly Gates' Schematics for the JTAG Dongle
2. Modified Schematic for the JTAG Dongle Circuit Using 74LS541
Which can I use?
Hi all,
I have a iMate SP3 here that I'm trying to get working for a coworker. Long story short they did this once before and I re-flashed it with some ROM (no clue which one) to get it working. Well, they broke it again and it's at the bootloader screen.
Problem is, I have no clue what CID lock is on the phone. The SPL is 1.01.0107 and I can't really find any mention of it. The phone doesn't boot any further than the bootloader screen and needs to be flashed, but I'm not sure with what. So far it's rejected all the ROMs I've tried.
Info 2 in MTTY gives me the output below:
HTCSCDL___01 4š«@HTCE
Can anyone tell me what I can flash this phone with to get something booting on it again? Thanks
please visit ftp://ftp.clubimate.com
choose the appropriate rom for you