Frustrating problem - HTC Typhoon

I am stuck on the bootloader screen... I have IPL 1.00 and SPL 1.00.0006 I am unable to flash it because active sync wont detect... I have search and have found nothing (maybe Im searching for the wrong thing) can someone point me in the right direction? Thank you!

When I use the multiport-tty This is what I keep getting. WHat am I doing wrong?
Cmd>l c:/os.bin
clean up the image temp buffer at 0x8C080000 Length 0x01B00000
MTTYDownloadImageNot allow operation!
Error : DownloadImage return error (code = 0xFFFFFFFF)
Cmd>

Related

T-mobile SDA WM6 Bad Flash ?

Hi all,
I've tried to refresh my old SDA ROM from wm5 to wm6 this morning but after follow steps from http://forum.xda-developers.com/showthread.php?t=317209&page=9 my mobile start with typical tricolor screen with :
IPL 1.00
SPL 1.01.0064
I've tried to flash with mtty1.42 but program return :
l c:\wm6.bin
clean up the image temp buffer at 0x8C080000 Length 0x01B00000
MTTYDownloadImageNot allow operation!
Error : DownloadImage return error (code = 0xFFFFFFFF)
Could you help me ?
Thanx
Hi!
You have need it spl flashing!
http://www.geocities.com/gggbitonti/typhoon.htm
Follow the instructions!
Thanx for your reply Dibi,
I need to have my SDA working to use Patched_RUU.exe, but mine still start with tricolor screen :-(

Please Help me To Unbrick my device

Brother i am upgrading my device it stoped at 2% now its dead only goes to bootloader show
ipl 1.81.00001
spl 1.81.00001
i master reset but nothing happened i flash all roms on wiki nothing happened always say invalid tool
i need this rom because this has previous this
Rom version 1.8.415.2 wwe
Rom date 11-3-06
Radio 02.71.90
protocol version 4.1.13.31
EXT Rom 1.8.415.102
Thanks in advance who help me in this case
I have another set of that how can i read other set rom and flash in to that set
Was it CID locked? did you buy the phone r did you get it with a subsciption?
oddball1 said:
Was it CID locked? did you buy the phone r did you get it with a subsciption?
Click to expand...
Click to collapse
Not it is Not Cid locked & Also Not Sim Locked.. yes i buy from a shop in pakistan but when i upgrade i get problem
I also have bricked my Herald after upgrading to Aserg but nothing now ,,only green screen and off ...
it was CID locked
from Mobinil Plz Help
zubi1984: i had the same problem.
try mtty.exe (use wiki), and try the commands for it.
if it says something clearly, then you can -somehow- unbrick your device.
if it gives error..
-this happedned to me-
you should bring it to the service, with warranty.
if you are lucky, they will fix it to you without price.
i hope you have warranty, because the man in the service said that i really fuc*ed it up... the new motherboard would have been very expensive.. without warranty
so first of all, calm down, and let's start reading about the upgrade, read a lot, and go to another forums, maybe somebody can help to you unbrick your device
____
my device said:
error 30* invalid upgrade tool (for any roms)
only in bootloader mode running
hard reset failed
reset does not works
no charge lights on charge
mtty.exe error, commands: no answere.
pulyka
Hi pulyka, Can you Please tell me about commands for mtty.exe..what to write inside te command box exactly ,,
any more details about "mtty " would be thankful
for me:
Cmd>info 1
Invalid command : info 1
For a help screen, use command ? or h
Cmd>info 2
Invalid command : info 2
For a help screen, use command ? or h
_____________
this is wrong.
___
read it carefully!
http://wiki.xda-developers.com/index.php?pagename=Hermes_BootLoader
try it, but in your own risk..
unfortunately i am not an expert in this..
some people helped me in a hungarian forum.. and they said, my pda is bricked completely:S
if mtty working properly:
sb
I already connect to USB!
Cmd>info 0
GetDeviceInfo=0x00000000
Wizard
Cmd>info 1
GetDeviceInfo=0x00000001
2.21.0000
Cmd>info 2
GetDeviceInfo=0x00000002
+ SD Controller init
- SD Controller init
+StorageInit
***** user area size = 0x1EB80000 Bytes
HTCSWIZTMO07 â-r€HTCE
Cmd>info 3
GetDeviceInfo=0x00000003
this is died device:
info1
Invalid command : info1
For a help screen, use command ? or h
Cmd>info 1
GetDeviceInfo=0x00000001
2.24.0000
Cmd>info 0
GetDeviceInfo=0x00000000
Wizard
Cmd>r2sd all
***** user area size = 0x1DE40000 Bytes
R2SDBackup() - Download type = 5
usTotalBlock = 1 sizeof(SDCARD_SIGNATRUE_TABLE)=512
GetDeviceCID: Error - InitDecoder
GetDeviceCID: Error - InitDecoder
You didn't get the proper security level to download a specific image
Cmd>
pulyka

Help...I'm the freshman in playing X01HT Softbank

Cmd> lnbs SPL-1.01.nbs 50020000
:F=SPL-1.01.nbs
:A=50020000
:O=00000000
:L=FFFFFFFF
start NB image downloadS
Load ADDR: 50020000 Length: 402C4
H***
SPL flag is incorrect, please check your SPL is correct.
Write NAND error, addr=0x50020000
Error !! The image must be in ROM area.
BTW
I want to update my sys to WM6.1
What does this mean?
I wanna to change my spl to 1.01
my herm200
IPL-1.04
SPL*2.01.olipro
I am being online to wait your answers
thanks

Get 300 Error, goldcard doesn't help?

After trying to upgrade firmware on Herald got brick(?)
When i try to upgrade it by Rom Update Utility - always get 300 error.
I've tried to make Goldcard (tried 3 different sd-cards) with QMAT and typhoonnbfdecode perl script, goldcard always creates succesfully, but
f*** Searching for SD card and moment later tri-color then...
Before that everything was o.k...
When i turn it on there is green display...
Any ideas guys? any suggestions??? what mistakes could i made?
mtty says
SDInit---
SDInit OK
Unlimited time!
GetDeviceCID: Error - InitDecoder
g_cKeyCardSecurityLevel = 0
....
Cmd>getdevinfo
GetDeviceCID: Error - InitDecoder

Now what?

So, now I cant get anything working in my P4350 except the bootloader mode.
The way I got here:
Installed many roms, trying to find the best for me. After some time, even the most stable rom was not stable, all of them crashed, freezed, rebooted after about 1 day usage. (With and without SD card, and no apps installed).
So I decided to remove hardspl and do the whole thing again. I downloaded Aserg-Remove-Hard-Spl pack, and run it. After the second step the phone was not completly blank, I saw the console staying at the "praying ..." text (without backlight), and the phone didnt responded for any buttons or touch. So here came the third step, the RUU, but it gave me error 260, that it cant find my device. (How would this, since the activesync was not connected?)
So i couldnt do anything, I soft reseted the phone, but it wont turned on, or it did but the screen left blank. - like no rom were installed. I tried to press the camera, and the RGB screen came up, saying IPL 4.14.0001 and SPL 4.70 Yang.
Tried to hard reset, but when I pressed send, it said fail.
Tried to update at this position with RUU, but its need activesync so it gave me the same error. Tried to install 3 different roms from 2 differenct SD Cards (that worked before), and It checks the Card, the the RGB screen comes up (like no rom would be on the SD card).
Created a GoldCard, and installed the official ROM. The "Checking SD Card" text stays here for 5 secs, then the RGB screen comes up.. wtf?
Same with heradiag.nbh
Now tried again the Hard reset, it said succesfull, but when it tries to boot I just get a green to black gardient image, something like this: http://www.cylekx.net/help/tutorial_assets/images/byte ramp and green gradient.jpg (but rotated), and nothing else happens.
Any ideas to get the device back to life?
Maybe there are some hardware malfunction inside the phone?
Thanks, and sorry if I posted this to a wrong thread. (was not sure where it should go)
Just got a WhiteScreen crash at the "Checking SD Contents" screen.. It cant be software problem i guess.
Cmd>getdevinfo
GetDeviceCID: Error - InitDecoder
HTCSHTCE
Cmd>ls
clean up the image temp buffer at 0x8C100000 Length 0x03A00000
BOOTLOAD_PAGE_TABLE_BASE_C_VIRTUAL= 0x8C080000
Clear image temp buffer done .
MTTYDownloadImage
start download
==CreateFile err==nb0 Sync bytes error(0) 6B != 42
Error : DownloadImage return error (code = 0xFFFFFFFF)
While your phone is in Bootloader mode, install the original ROM with the RUU. All Heralds (P4350) and Atlas'(Wing P4351) can be flashed while on the bootloader screen. Just disregard the step on the RUU that says to make sure your phone is connected to ActiveSync. Also if you have downloaded the whole RUU for the Original ROM, you have to edit the .EXE file to remove the .SPL file that is inside. You can use 7-Zip to get inside of the .EXE file. If not, then just install the ROM as you normally would. You will not need a SD card to install this. Let us know what happens. EVERYONE: if I have forgotten to mention something, please add.
baronmxc said:
While your phone is in Bootloader mode, install the original ROM with the RUU. All Heralds (P4350) and Atlas'(Wing P4351) can be flashed while on the bootloader screen. Just disregard the step on the RUU that says to make sure your phone is connected to ActiveSync. Also if you have downloaded the whole RUU for the Original ROM, you have to edit the .EXE file to remove the .SPL file that is inside. You can use 7-Zip to get inside of the .EXE file. If not, then just install the ROM as you normally would. You will not need a SD card to install this. Let us know what happens. EVERYONE: if I have forgotten to mention something, please add.
Click to expand...
Click to collapse
Hah, i was so unlucky A chip on the motherboard burnt, so if u plugged in the USB it crashed immadiatelly, no wonder why the PC couldnt recognise it..
But still have a problem. Tried to flash the original shipped rom, and another costum rom but both said INVALID MODEL ID.
So what now?
thanks
Cmd>getdevinfo
GetDeviceCID: Error - InitDecoder
HTCSHTCE
Cmd>ls
clean up the image temp buffer at 0x8C100000 Length 0x03A00000
BOOTLOAD_PAGE_TABLE_BASE_C_VIRTUAL= 0x8C080000
Clear image temp buffer done .
MTTYDownloadImage
start download
==CreateFile err==nb0 Sync bytes error(0) 6B != 42
Error : DownloadImage return error (code = 0xFFFFFFFF)
Cmd>set 32
+ SD Controller init
- SD Controller init
+StorageInit
SDInit+++
PL_SDSetSlotNumber() - MPUIO_SDIF_SEL1=0, MPUIO_SD_IF_SEL=0
SDInit - SD ver2.00
SDCmd1 Command response time-out. MMC_STAT = 80
SDCmd1 Command response time-out. MMC_STAT = 80
SDCmd1 Command response time-out. MMC_STAT = 80
SDCmd55 Card status error in response. MMC_STAT = 4000
SD Ver2.00: Low Capacity
SD clock to 24MHz
***** user area size = 0x79A00000 Bytes
SDInit---
SDInit OK
Unlimited time!
GetDeviceCID: Error - InitDecoder
g_cKeyCardSecurityLevel = 0
HTCE
More Info:
Now i can connect with MTTY and write commands in the bootloader. With this SPL version most commands i found doesnt work, but I got some information about my phones status: the GoldCard's security level is 0, thats correct. The problem is with the CID: GetDeviceCID: Error - InitDecode
I think the problem is this, since it cant get the CID, cant verify the rom matches .
I can write things with mtty into ram or storage, is it possible to write the whole rom directly to the devices boot dir?
CheeseDave said:
Hah, i was so unlucky A chip on the motherboard burnt, so if u plugged in the USB it crashed immadiatelly, no wonder why the PC couldnt recognise it..
But still have a problem. Tried to flash the original shipped rom, and another costum rom but both said INVALID MODEL ID.
So what now?
thanks
More Info:
Now i can connect with MTTY and write commands in the bootloader. With this SPL version most commands i found doesnt work, but I got some information about my phones status: the GoldCard's security level is 0, thats correct. The problem is with the CID: GetDeviceCID: Error - InitDecode
I think the problem is this, since it cant get the CID, cant verify the rom matches .
I can write things with mtty into ram or storage, is it possible to write the whole rom directly to the devices boot dir?
Click to expand...
Click to collapse
a INVALID MODEL ID error occurs when you use the wrong RUU/ROM for a phone. Heralds must use the Herald RUU and Wings must use the Wing RUU.
Herald RUU (P4350) <- English version is the 3rd link.
T-Mobile Wing [Atlas](P4351) RUU <- Phone Number and IMEI Required
T-Mobile Wing [Atlas](P4351) RUU<- Phone Number and IMEI NOT Required however I believe that this is an older Windows 6.0 Build
If you want to keep your phone hard spl'd, you need to modify the EXE of the RUU and erase the SPL.nbh file.
As far as writing the ROM directly, that is out of my expertise. Someone else will have to answer that.
baronmxc said:
a INVALID MODEL ID error occurs when you use the wrong RUU/ROM for a phone. Heralds must use the Herald RUU and Wings must use the Wing RUU.
Herald RUU (P4350) <- English version is the 3rd link.
T-Mobile Wing [Atlas](P4351) RUU <- Phone Number and IMEI Required
T-Mobile Wing [Atlas](P4351) RUU<- Phone Number and IMEI NOT Required however I believe that this is an older Windows 6.0 Build
If you want to keep your phone hard spl'd, you need to modify the EXE of the RUU and erase the SPL.nbh file.
As far as writing the ROM directly, that is out of my expertise. Someone else will have to answer that.
Click to expand...
Click to collapse
Thanks for your help, but as i said my device ID is messed up with the USPL process... "GetDeviceCID: Error - InitDecoder" None of the RUUs works.
Waiting for the directly-writing method, or i'll have to replace the storage at the mainboard... (wont be cheap).

Categories

Resources