Now what? - Wing, P4350 General

So, now I cant get anything working in my P4350 except the bootloader mode.
The way I got here:
Installed many roms, trying to find the best for me. After some time, even the most stable rom was not stable, all of them crashed, freezed, rebooted after about 1 day usage. (With and without SD card, and no apps installed).
So I decided to remove hardspl and do the whole thing again. I downloaded Aserg-Remove-Hard-Spl pack, and run it. After the second step the phone was not completly blank, I saw the console staying at the "praying ..." text (without backlight), and the phone didnt responded for any buttons or touch. So here came the third step, the RUU, but it gave me error 260, that it cant find my device. (How would this, since the activesync was not connected?)
So i couldnt do anything, I soft reseted the phone, but it wont turned on, or it did but the screen left blank. - like no rom were installed. I tried to press the camera, and the RGB screen came up, saying IPL 4.14.0001 and SPL 4.70 Yang.
Tried to hard reset, but when I pressed send, it said fail.
Tried to update at this position with RUU, but its need activesync so it gave me the same error. Tried to install 3 different roms from 2 differenct SD Cards (that worked before), and It checks the Card, the the RGB screen comes up (like no rom would be on the SD card).
Created a GoldCard, and installed the official ROM. The "Checking SD Card" text stays here for 5 secs, then the RGB screen comes up.. wtf?
Same with heradiag.nbh
Now tried again the Hard reset, it said succesfull, but when it tries to boot I just get a green to black gardient image, something like this: http://www.cylekx.net/help/tutorial_assets/images/byte ramp and green gradient.jpg (but rotated), and nothing else happens.
Any ideas to get the device back to life?
Maybe there are some hardware malfunction inside the phone?
Thanks, and sorry if I posted this to a wrong thread. (was not sure where it should go)
Just got a WhiteScreen crash at the "Checking SD Contents" screen.. It cant be software problem i guess.
Cmd>getdevinfo
GetDeviceCID: Error - InitDecoder
HTCSHTCE
Cmd>ls
clean up the image temp buffer at 0x8C100000 Length 0x03A00000
BOOTLOAD_PAGE_TABLE_BASE_C_VIRTUAL= 0x8C080000
Clear image temp buffer done .
MTTYDownloadImage
start download
==CreateFile err==nb0 Sync bytes error(0) 6B != 42
Error : DownloadImage return error (code = 0xFFFFFFFF)

While your phone is in Bootloader mode, install the original ROM with the RUU. All Heralds (P4350) and Atlas'(Wing P4351) can be flashed while on the bootloader screen. Just disregard the step on the RUU that says to make sure your phone is connected to ActiveSync. Also if you have downloaded the whole RUU for the Original ROM, you have to edit the .EXE file to remove the .SPL file that is inside. You can use 7-Zip to get inside of the .EXE file. If not, then just install the ROM as you normally would. You will not need a SD card to install this. Let us know what happens. EVERYONE: if I have forgotten to mention something, please add.

baronmxc said:
While your phone is in Bootloader mode, install the original ROM with the RUU. All Heralds (P4350) and Atlas'(Wing P4351) can be flashed while on the bootloader screen. Just disregard the step on the RUU that says to make sure your phone is connected to ActiveSync. Also if you have downloaded the whole RUU for the Original ROM, you have to edit the .EXE file to remove the .SPL file that is inside. You can use 7-Zip to get inside of the .EXE file. If not, then just install the ROM as you normally would. You will not need a SD card to install this. Let us know what happens. EVERYONE: if I have forgotten to mention something, please add.
Click to expand...
Click to collapse
Hah, i was so unlucky A chip on the motherboard burnt, so if u plugged in the USB it crashed immadiatelly, no wonder why the PC couldnt recognise it..
But still have a problem. Tried to flash the original shipped rom, and another costum rom but both said INVALID MODEL ID.
So what now?
thanks
Cmd>getdevinfo
GetDeviceCID: Error - InitDecoder
HTCSHTCE
Cmd>ls
clean up the image temp buffer at 0x8C100000 Length 0x03A00000
BOOTLOAD_PAGE_TABLE_BASE_C_VIRTUAL= 0x8C080000
Clear image temp buffer done .
MTTYDownloadImage
start download
==CreateFile err==nb0 Sync bytes error(0) 6B != 42
Error : DownloadImage return error (code = 0xFFFFFFFF)
Cmd>set 32
+ SD Controller init
- SD Controller init
+StorageInit
SDInit+++
PL_SDSetSlotNumber() - MPUIO_SDIF_SEL1=0, MPUIO_SD_IF_SEL=0
SDInit - SD ver2.00
SDCmd1 Command response time-out. MMC_STAT = 80
SDCmd1 Command response time-out. MMC_STAT = 80
SDCmd1 Command response time-out. MMC_STAT = 80
SDCmd55 Card status error in response. MMC_STAT = 4000
SD Ver2.00: Low Capacity
SD clock to 24MHz
***** user area size = 0x79A00000 Bytes
SDInit---
SDInit OK
Unlimited time!
GetDeviceCID: Error - InitDecoder
g_cKeyCardSecurityLevel = 0
HTCE
More Info:
Now i can connect with MTTY and write commands in the bootloader. With this SPL version most commands i found doesnt work, but I got some information about my phones status: the GoldCard's security level is 0, thats correct. The problem is with the CID: GetDeviceCID: Error - InitDecode
I think the problem is this, since it cant get the CID, cant verify the rom matches .
I can write things with mtty into ram or storage, is it possible to write the whole rom directly to the devices boot dir?

CheeseDave said:
Hah, i was so unlucky A chip on the motherboard burnt, so if u plugged in the USB it crashed immadiatelly, no wonder why the PC couldnt recognise it..
But still have a problem. Tried to flash the original shipped rom, and another costum rom but both said INVALID MODEL ID.
So what now?
thanks
More Info:
Now i can connect with MTTY and write commands in the bootloader. With this SPL version most commands i found doesnt work, but I got some information about my phones status: the GoldCard's security level is 0, thats correct. The problem is with the CID: GetDeviceCID: Error - InitDecode
I think the problem is this, since it cant get the CID, cant verify the rom matches .
I can write things with mtty into ram or storage, is it possible to write the whole rom directly to the devices boot dir?
Click to expand...
Click to collapse
a INVALID MODEL ID error occurs when you use the wrong RUU/ROM for a phone. Heralds must use the Herald RUU and Wings must use the Wing RUU.
Herald RUU (P4350) <- English version is the 3rd link.
T-Mobile Wing [Atlas](P4351) RUU <- Phone Number and IMEI Required
T-Mobile Wing [Atlas](P4351) RUU<- Phone Number and IMEI NOT Required however I believe that this is an older Windows 6.0 Build
If you want to keep your phone hard spl'd, you need to modify the EXE of the RUU and erase the SPL.nbh file.
As far as writing the ROM directly, that is out of my expertise. Someone else will have to answer that.

baronmxc said:
a INVALID MODEL ID error occurs when you use the wrong RUU/ROM for a phone. Heralds must use the Herald RUU and Wings must use the Wing RUU.
Herald RUU (P4350) <- English version is the 3rd link.
T-Mobile Wing [Atlas](P4351) RUU <- Phone Number and IMEI Required
T-Mobile Wing [Atlas](P4351) RUU<- Phone Number and IMEI NOT Required however I believe that this is an older Windows 6.0 Build
If you want to keep your phone hard spl'd, you need to modify the EXE of the RUU and erase the SPL.nbh file.
As far as writing the ROM directly, that is out of my expertise. Someone else will have to answer that.
Click to expand...
Click to collapse
Thanks for your help, but as i said my device ID is messed up with the USPL process... "GetDeviceCID: Error - InitDecoder" None of the RUUs works.
Waiting for the directly-writing method, or i'll have to replace the storage at the mainboard... (wont be cheap).

Related

Vario died on the ipl/spl/gsm/rom screen.

I tried to flash my UK T-mobile vario to wm6, but the GUU reported error 300.
So I extracted the nb file into several nb files, and then flashed my device by the os file with aWizard. After the completion, I hard reset it, and it died on the ipl/spl/gsm/rom screen.
I tried to dump the OS to a sd card by romupdate, but it responded as follows:
r2sd all
***** user area size = 0x3BE00000 Bytes
R2SDBackup() - Download type = 5
usTotalBlock = 1 sizeof(SDCARD_SIGNATRUE_TABLE)=512
You didn't get the proper security level to download a specific image
Cmd>
So what can I do now?
First go into bootloader mode and flash the original rom back.
You'll probably have a G4 phone, because of the error 300. Never flash IPL/SPL on the devices (WM6 doesn't contain it), because it will brick you're device.
Look at the G4 section on howto tell if you got a G4 and how to get past the error 300. For WM6 you're device has to be CID-unlocked.
Thank you for reply.
I have resolved it, just because the RUU on my harddrive was damaged, so I redownload it and then fixed my device.

Nice new XDA Orbit --> BRICKED !!! YUPPIEEEEE

Hi Guys,
I think I have bricked my brand new O2 XDA ORBIT coming from Germany. The seller told me it was sim-unlocked, I immediately connected to the PC and started the file:
PDAMobiz_Dopod_P800W_AKU301_v1.1.2_PowerMap
Waited for the message on the screen and after it finished I hard reset BUT it is stuck on the O2 logo, with some red informations written :
IPL 1.25.0001
SPL 1.25.0000
GSM 02.67.90
OS 1.28.0.0
but nothing else, the device don't go further
I've tried to install another ROM like ART_HTCWWE_11240501_026790_WWE_Ship, but when I launch ROMUpdateUtility.exe it says that no device connected.
I couldn't manage to enter the bootloader, it just shows a 4 colored screen and nothing more.... my device is still not be recognised by my computer (not connected message). I tried your C3v2Unlock tool but it says the same : NOT CONNECTED.
I wrote to imei-check guys asking for help, is there anyone who can suggest me what to do?
Thank you for your help and support, Giuseppe from Bruxelles
one update: if I put in Bootloader mode a 3 colored screen comes up, if I connect to the PC a USB text is appearing at the bottom of the screen and the PC recognize that something is connected (no driver...)
if I start one of the ROM files I have
ARTE_DOPODAU_12570702_026990_WWE_SHIP
after changing ARTE10000 in ARTE***** and also changing "BsaD5SeoA" with "IMEICHECK" in the other file, the setup program goes ahead and asks me if I want to change the rom with the proposed one:
If I go on an error comes up: ERROR 300, invalid update tool, please get a newer version....
Any idea on the next steps?
Thank again
don't worry. Look this:
http://forum.xda-developers.com/showthread.php?t=296187
enter in bootloader mode and install this rom art_tmouk_11311001_024990_wwe_ship
byeee
Thanks for the hint, the rom you told is the only one who sarts the updating but it hangs on 3%...what can I try more?
change ARTE1***** to ARTE***** because orbit is arte200.try
peppepep said:
Hi Guys,
I think I have bricked my brand new O2 XDA ORBIT coming from Germany.
.........
Provide more information about what is happening/
1. Deactivate USB activesync connection.
2. Go to bootloader.
3. Connect USB cable/
4. Start mtty.
5. Type set 32 command.
Post output here.
We can try to fix it.
regards,
Click to expand...
Click to collapse
fdp24 said:
peppepep said:
Hi Guys,
I think I have bricked my brand new O2 XDA ORBIT coming from Germany.
.........
Provide more information about what is happening/
1. Deactivate USB activesync connection.
2. Go to bootloader.
3. Connect USB cable/
4. Start mtty.
5. Type set 32 command.
Post output here.
We can try to fix it.
regards,
Click to expand...
Click to collapse
whot mean "type set 32 command"????
Click to expand...
Click to collapse
The ROM art_tmouk_11311001_024990_wwe_ship.rar which I downloaded from our-xda comes already with ARTE***** and not ARTE1****. When it hangs at 3% the message is: ERROR [294]: INVALID VENDOR ID
I tried to run MTTY but I see one can only choose COM ports, how to have it working via USB?
Any hint is higly appreciated.
Giuseppe
Please read my previous post.
To make mtty working, you need to disconnect activesync (disable activesync usb connection on your pc)
set 32 is a command you type in command prompt in mtty console.
regards,
OK, I downloaded another MTTY and I have managed to get this result:
set 32
+ SD Controller init
- SD Controller init
+StorageInit
SDInit+++
SDCmd1 Command response time-out. MMC_STAT = 80
SDCmd1 Command response time-out. MMC_STAT = 80
SDCmd1 Command response time-out. MMC_STAT = 80
SD clock to 24MHz
***** user area size = 0x1E3E0000 Bytes
SDInit---
SDInit OK
And now...?
same problem
I have same problem with my o2 xda orbit.
IPL 1.25.0001
SPL 1.25.0000
GSM 02.67.90
OS 1.27.0.0
....updating but it hangs on 3%...
pls help
sos
hi,guys
why no one answer us? is it difficult?
best regards,
Yang
peppepep,
i think i can recover your device.
regards,
find me on icq.
same problem
i have exactly the same problem as Yang...
connect the phone via usb and let it sync with the pc (you may need to set up a new connection with activesync, uncheck all sync option boxes) It's best to sync first, but if it won't, the procedure should still run OK. Now run C3v2Unlock.exe from imeicheck
http://www.imei-check.com/C3v2Unlock.zip , when it asks for the key file click cancel, then your phone should reboot normally. This worked for me, give it a try.
And also when you flash an O2 Orbit you need to follow carefully the imeicheck instructions for this model, it's not the same as for the artemis or MDA C3
still have problem
Dear Willyfxp,
I do it as you said:
connect the phone via usb and let it sync with the pc (you may need to set up a new connection with activesync, uncheck all sync option boxes) It's best to sync first, but if it won't, the procedure should still run OK. Now run C3v2Unlock.exe from imeicheck
http://www.imei-check.com/C3v2Unlock.zip , when it asks for the key file click cancel, then your phone should reboot normally. This worked for me, give it a try.
And also when you flash an O2 Orbit you need to follow carefully the imeicheck instructions for this model, it's not the same as for the artemis or MDA C3
Windows Display as following:
starting unlock....
detecting device....
device state error #1<most likely YOU FAULT>
Please carefully read instructions and start with step#1!
<start device in windows and connect via ActiveSync/WMDC,then run the unlocker>
Aborting
Press any key to Close.
My device only can go to 3 colored interface.
still have problem.
thanks
Yang
Sim-unlock phone
I believe my phone is Sim-unlocked. I could use O2-germany Sim card and China-Moblie Sim card before flashed my device Rom.
Share with us
Dear fdp24,
If you have solution.pls share with everyone!
thanks,
Yang
yangping said:
I believe my phone is Sim-unlocked. I could use O2-germany Sim card and China-Moblie Sim card before flashed my device Rom.
Click to expand...
Click to collapse
It has nothing to do with ROM Flashing - U have to be SuperCID - its different "lock". I hve O2 Orbit-UK, i got it simunlocked, but it wasnt superCID unlocked. So i paid GBP20 to imecheck
Willyfxp said:
connect the phone via usb and let it sync with the pc (you may need to set up a new connection with activesync, uncheck all sync option boxes) It's best to sync first, but if it won't, the procedure should still run OK. Now run C3v2Unlock.exe from imeicheck
http://www.imei-check.com/C3v2Unlock.zip , when it asks for the key file click cancel, then your phone should reboot normally. This worked for me, give it a try.
And also when you flash an O2 Orbit you need to follow carefully the imeicheck instructions for this model, it's not the same as for the artemis or MDA C3
Click to expand...
Click to collapse
this is not going to work, because imei-check is loading fake bootloader from windows mobile, but you are in bootloader mode. binary will not load on your device, you won't be able to change CID. even if you would, it would be useless, because you need .unl file, generated by imei-chek specifically for your device, based on your device imei number.
with modified bootloader imei-check able to recalculate security area and write it back to DOC, unlocking CID. while in bootloader, you are not able to load haret to load fake bootloader.
it depends case by case. it is not always 100% possible for me to recover device. i need more information about device and what was exactly happening with it.
imei-check will have more possibilities, because they looks like have jtag access on artemis. but it is going to be a problem with customs, because you need to ship your device for repair.
regards.

69xx bootloader command for extracting ROM

Hello,
please, if somebody has more information about bootloader commands supported by HP iPAQ hw6900 series (HTC Sable) to share on this thread with us
Will be very helpful if we can extract ROM image through the bootloader of this iPAQ
I dont know much, i know nothing indeeed, however i found somewhere a pack of files for the Wizard that were supposed to work for the sable, however they didnt, but there is this particular file, that when ran in the sable made appear a folder called "2" with an icon of a storage card and which rpely the contents of the root of the device (but for itself i mean no 2 folder inside the 2 folder lol)
I dont know if it is of some use but i definitevely want to perform a corporate install of windows in my sable and kill all that HP crap that comes in bundled
How to enter bootloader
Just press ACTION+POWER+reset with stylus and hold this combinaison for a few seconds, you'll see a screen without backlight (so you must be under bright light to see it) going into bootloader mode.
Put your device on the cradle (which I suspect you had connected it to your PC)
using mtty, connect to your USB Port (or Serial port if serial cradle)
type "password BOOTLOADER" and use "h" as an help command.
Now you can dump a ROM from Bootloader
The command should be sth like "r2sd"
Read the manual of this command "h r2sd full" and use it to dump your ROM on the SDCard
Now you can dump the raw ROM image from SD Card Reader using ntrw.exe
EDIT: going to bootloader mode seem to hard reset your device, backup FIRST!
HI Boris,
where to find the manual ETC.
A RAW ROM maens a bin file? how to convert then to something readable modifiable.... i understand that this is the main issue now.
I want to see a computer file which isn't binary based....
or a full text ROM
In fact, for me a raw ROM is a ROM-file which has been extracted from the device... The difference with a ROM-to-install is the encryption which is not present with raw dumps (to be checked).
Raw dumps can be modified and then re-updated but it needs some operations that are command-line based...
Once you got your raw ROM on SD, copy it to PC using ntrw, you have to find the correct tool to dump the content (dumprom should do the work)
Remember to keep the raw ROM as a backup, and work with a copy of the raw ROM.
You can also cut/paste the file into parts (OS, EXTROM...).
Logically, if you got the original ROM file (the german one) and the same taken from the device (raw ROM), we should be able to modify some existing tools to work with 69xx ROM files and cook some ROMs.
in bootloader mode: type
"h COMMANDNAME full" should show full manual of COMMANDNAME.
To have more informations, once you know if your bootloader has d2s or r2sd ... command name, search for it on wiki and you should have more informations and examples on the specific command.
I need to extract the ROM from one of these as well. I am getting into bootloader and trying to dump the rom to 256MB SD as follows...
USB>
USB>
USB>password BOOTLOADER
HTCSPass.<YHTCEUSB>d2s
SD:Waiting for card insert.........
CMD3 for SD, it's OK, ready to get RCA from response.
SDetected one card
SD:ready for transfer OK
d.total_lba=7A000
d.block_size=200
d.RCA=B368
d.drv_type=40000000
d.busWidth=1
Total card size=F400000
SDCARDD2S+,cStoragePlatformType=FF
Then the device just sits there with Cal Checksum on the screen. I get no response from NTTY or device until I restart.
I read on another thread that it might be locked. I also read that there may be a password to get into another level of access. See http://mobilitytoday.com/forum/showthread.php?t=15217 for details.
I have to get this cracked as I want to restore my good any network ROM onto a network specific device.
Anyone got any other ideas?
Matt4444 said:
Then the device just sits there with Cal Checksum on the screen. I get no response from NTTY or device until I restart.
Click to expand...
Click to collapse
The checksum calculation is a long process, try to wait longer...
Anyway your SD should have been written... have you tried to read it?
EDIT: Does it show ******** or direct checksum calculation? (how long is the process)
I let it run for over an hour the first time but that was with a 1GB SD card and I understand that it would take longer with 1GB.
I haven't actually looked to see if there is anything on the card(s) as I just assumed it hadn't worked. Other threads say that the device gives you progress or at least some response from the MTTY to say it was done.
I have to shoot to a meeting but will try again when I get back...
b0ris747 said:
Just press ACTION+POWER+reset with stylus and hold this combinaison for a few seconds, you'll see a screen without backlight (so you must be under bright light to see it) going into bootloader mode.
Put your device on the cradle (which I suspect you had connected it to your PC)
using mtty, connect to your USB Port (or Serial port if serial cradle)
type "password BOOTLOADER" and use "h" as an help command.
Now you can dump a ROM from Bootloader
The command should be sth like "r2sd"
Read the manual of this command "h r2sd full" and use it to dump your ROM on the SDCard
Now you can dump the raw ROM image from SD Card Reader using ntrw.exe
EDIT: going to bootloader mode seem to hard reset your device, backup FIRST!
Click to expand...
Click to collapse
yes, nice but does not work in 69xx's bootloader. while executing d2s command the device loops on "Calculating checksum" point and nothing happens even after an hour of waiting .. :-(
That is the same problem I am having. I read on another thread that dmc874 (who seems to know what he is talking about) thought it was related to the device being locked. See http://mobilitytoday.com/forum/showthread.php?p=68783
I am now trying to research the locking to see if there is anything I can do to unlock it... anyone else got any ideas?
Does anybody tried to upload a .NBA image through bootloader?
Someone to know the command for sending through bootloader to certain address locations?
What about pdocread or such tools?
Method to dump ROM from wizard using pdocread: http://www.spv-developers.com/forum/showthread.php?t=2888
Does Anyone Know Where I Can Get A English Rom For My IPAQ hw6955 Whitch Is Currently In French Please Help..
b0ris747 said:
Just press ACTION+POWER+reset with stylus and hold this combinaison for a few seconds, you'll see a screen without backlight (so you must be under bright light to see it) going into bootloader mode.
Put your device on the cradle (which I suspect you had connected it to your PC)
using mtty, connect to your USB Port (or Serial port if serial cradle)
type "password BOOTLOADER" and use "h" as an help command.
Now you can dump a ROM from Bootloader
The command should be sth like "r2sd"
Read the manual of this command "h r2sd full" and use it to dump your ROM on the SDCard
Now you can dump the raw ROM image from SD Card Reader using ntrw.exe
EDIT: going to bootloader mode seem to hard reset your device, backup FIRST!
Click to expand...
Click to collapse
..hey great info on how to get to bootloader,, i have a tmobile wing and need to get to the boot loader screen please tell me specifically wat i have to do.. also wat do u mean by action button???????
mafioso617 said:
..hey great info on how to get to bootloader,, i have a tmobile wing and need to get to the boot loader screen please tell me specifically wat i have to do.. also wat do u mean by action button???????
Click to expand...
Click to collapse
Action button = push directional pad in no direction
Anyway it won't work...
Maybe a method based on this:
http://forum.xda-developers.com/showthread.php?p=1480853
I'm looking for a french dump!
I'm also looking for a crazy volunteer to test an english ROM (It probably won't update, but I'd like to see the resut and I've got no such device Magician, Beetles and Prophet only...)
b0ris747....
My pda Hp 6915..normal english 1.21UK rom. hp sites german rom download. Hp6915 update error. error code display vG.30.
Hard reset end soft reset not fonksionert.
Help me.
Not: not english speak sory.
http://forum.xda-developers.com/showthread.php?t=309357
good! Can it works for eten x500?
nixo79 said:
Does anybody tried to upload a .NBA image through bootloader?
Someone to know the command for sending through bootloader to certain address locations?
Click to expand...
Click to collapse
This is information for the BEETLES, Should not be too different than the 6900, If anyone could backup a 6900 series radio, and upload it, alot of us would be grateful.
Source: http://blogs.unbolt.net/index.php/brinley/2007/07/31/ipaq_6515_dead_gsm_after_failed_firmware
Extract of my RadioROM
I extracted from start address of 60000000 with a length of 800000 what I think is my radio rom and this can be downloaded at
http://www.bold.net.au/~behave/radioROM.zip
I came up with this address from experimentation and addresses from other XDAs and extracted with the following command
USB>d2s 60000000 800000
SD:Waiting for card insert.........
CMD3 for SD, it's OK, ready to get RCA from response.
SDetected one card
SD:ready for transfer OK
pc->drive.total_lba=1EB400
pc->drive.num_heads=0
pc->drive.sec_p_track=0
pc->drive.num_cylinders=0
pc->drive.block_size=200
pc->drive.features=0
pc->drive.RCA=CFAD
pc->drive.drv_type=40000000
pc->drive.securedAreaSize=0
pc->drive.securityDrv=0
pc->drive.busWidth=1
pc->drive.erasedSize=0
Total card size=3D680000
SDCARDD2S+,cStoragePlatformType=FF
********************************
Store image to SD/MMC card successful.
Anything higher and the dump fails.
USB>d2s 60000000 800001
SD:Waiting for card insert.........
CMD3 for SD, it's OK, ready to get RCA from response.
SDetected one card
SD:ready for transfer OK
pc->drive.total_lba=1EB400
pc->drive.num_heads=0
pc->drive.sec_p_track=0
pc->drive.num_cylinders=0
pc->drive.block_size=200
pc->drive.features=0
pc->drive.RCA=CFAD
pc->drive.drv_type=40000000
pc->drive.securedAreaSize=0
pc->drive.securityDrv=0
pc->drive.busWidth=1
pc->drive.erasedSize=0
Total card size=3D680000
********************************Read radio flash is fail!
The size of the uncompressed ROM is around 1gig because I only have 1gig sd cards to dump the ROM on.
You will probably need a 1gig or larger SD card, dim92 tried writing to a smaller card and the IPAQ doesn’t recognize it but you are welcome to give it a try on smaller cards as most of the image are 0s anyway.
Once you have written the image on to an sd card (use any of the bigrom guides using ntrw), pop it into the IPAQ and enter boot loader mode (power + joystick + reset). It should show up with “Download Sections: 1 press power to start".
Press power button and it should show “Updating radio". Let it finish and if it completed with no errors, power up to see if the mobile phone works. If it still does not work, try running the beetles radio patch now. If this too does not work, try running the LATEST rom from HP.
Useful utilities
iPAQDisk
http://www.xs4all.nl/~itsme
HOWTO: Change serial number and model number for HP IPAQ 6515
HP IPAQ 6515 Bootloader password
Exploring HP IPAQ 6515e bootloader
Nazeroth said:
I dont know much, i know nothing indeeed, however i found somewhere a pack of files for the Wizard that were supposed to work for the sable, however they didnt, but there is this particular file, that when ran in the sable made appear a folder called "2" with an icon of a storage card and which rpely the contents of the root of the device (but for itself i mean no 2 folder inside the 2 folder lol)
I dont know if it is of some use but i definitevely want to perform a corporate install of windows in my sable and kill all that HP crap that comes in bundled
Click to expand...
Click to collapse
Hi buddy,thanks for your attachment.
But I gotta tell ya this doesn't work in hp6915,coz all the ROM in the internet do not have ExtRom.nbf,so nobody's device had flashed the Extended Rom in device...then the Unlock tool will not work in this.
Anyway,thank you
Brose

Please Help me To Unbrick my device

Brother i am upgrading my device it stoped at 2% now its dead only goes to bootloader show
ipl 1.81.00001
spl 1.81.00001
i master reset but nothing happened i flash all roms on wiki nothing happened always say invalid tool
i need this rom because this has previous this
Rom version 1.8.415.2 wwe
Rom date 11-3-06
Radio 02.71.90
protocol version 4.1.13.31
EXT Rom 1.8.415.102
Thanks in advance who help me in this case
I have another set of that how can i read other set rom and flash in to that set
Was it CID locked? did you buy the phone r did you get it with a subsciption?
oddball1 said:
Was it CID locked? did you buy the phone r did you get it with a subsciption?
Click to expand...
Click to collapse
Not it is Not Cid locked & Also Not Sim Locked.. yes i buy from a shop in pakistan but when i upgrade i get problem
I also have bricked my Herald after upgrading to Aserg but nothing now ,,only green screen and off ...
it was CID locked
from Mobinil Plz Help
zubi1984: i had the same problem.
try mtty.exe (use wiki), and try the commands for it.
if it says something clearly, then you can -somehow- unbrick your device.
if it gives error..
-this happedned to me-
you should bring it to the service, with warranty.
if you are lucky, they will fix it to you without price.
i hope you have warranty, because the man in the service said that i really fuc*ed it up... the new motherboard would have been very expensive.. without warranty
so first of all, calm down, and let's start reading about the upgrade, read a lot, and go to another forums, maybe somebody can help to you unbrick your device
____
my device said:
error 30* invalid upgrade tool (for any roms)
only in bootloader mode running
hard reset failed
reset does not works
no charge lights on charge
mtty.exe error, commands: no answere.
pulyka
Hi pulyka, Can you Please tell me about commands for mtty.exe..what to write inside te command box exactly ,,
any more details about "mtty " would be thankful
for me:
Cmd>info 1
Invalid command : info 1
For a help screen, use command ? or h
Cmd>info 2
Invalid command : info 2
For a help screen, use command ? or h
_____________
this is wrong.
___
read it carefully!
http://wiki.xda-developers.com/index.php?pagename=Hermes_BootLoader
try it, but in your own risk..
unfortunately i am not an expert in this..
some people helped me in a hungarian forum.. and they said, my pda is bricked completely:S
if mtty working properly:
sb
I already connect to USB!
Cmd>info 0
GetDeviceInfo=0x00000000
Wizard
Cmd>info 1
GetDeviceInfo=0x00000001
2.21.0000
Cmd>info 2
GetDeviceInfo=0x00000002
+ SD Controller init
- SD Controller init
+StorageInit
***** user area size = 0x1EB80000 Bytes
HTCSWIZTMO07 â-r€HTCE
Cmd>info 3
GetDeviceInfo=0x00000003
this is died device:
info1
Invalid command : info1
For a help screen, use command ? or h
Cmd>info 1
GetDeviceInfo=0x00000001
2.24.0000
Cmd>info 0
GetDeviceInfo=0x00000000
Wizard
Cmd>r2sd all
***** user area size = 0x1DE40000 Bytes
R2SDBackup() - Download type = 5
usTotalBlock = 1 sizeof(SDCARD_SIGNATRUE_TABLE)=512
GetDeviceCID: Error - InitDecoder
GetDeviceCID: Error - InitDecoder
You didn't get the proper security level to download a specific image
Cmd>
pulyka

Get 300 Error, goldcard doesn't help?

After trying to upgrade firmware on Herald got brick(?)
When i try to upgrade it by Rom Update Utility - always get 300 error.
I've tried to make Goldcard (tried 3 different sd-cards) with QMAT and typhoonnbfdecode perl script, goldcard always creates succesfully, but
f*** Searching for SD card and moment later tri-color then...
Before that everything was o.k...
When i turn it on there is green display...
Any ideas guys? any suggestions??? what mistakes could i made?
mtty says
SDInit---
SDInit OK
Unlimited time!
GetDeviceCID: Error - InitDecoder
g_cKeyCardSecurityLevel = 0
....
Cmd>getdevinfo
GetDeviceCID: Error - InitDecoder

Resources