Hi, I have a xPhoneII with (in bl mode):
TYPHOON IPL 1.00
TYPHOON SPL 2.05.0123
TYPHOON
Why I cannot upgrade it to wm5?
I have tried to use the instruction from ronswens, but there is an error, infect in step 4/5 I cannot see any "Need an UI (0)?" !!
Can you help me?
Daniele
4. Press Camera button and holding it insert USB connector (or holding Camera button press Power button for 1-2 seconds)
5. When "Need an UI (0)?" appears on the screen press [0] immediately.
6. You will see tricolor screen, in the blue zone there will be "Typhoon IU" message, if you see "Typhoon XIP" you were late to press [0], start from beginning.
Related
hi my new dopod has a problems
after soft reset it struck on HTC BOOT Screen
i hard reset it using 1]camera button 2]connection 3]reset
and press green key
but stiil struck on HTC screen
please i want om update
thanks
Hi, u might try this
step 1
camera + connection + reset
step 2
hold camera + connection, just release reset only
step 3
still hold camera + connection + green button
should be ok, there is mistake on the manual, the way u do should be still performing soft reset, I think
ok i tried that ant it says format complete but still stuck on HTC
tried rom update but error 260
please help
what is the send button ?
A black screen tells me "press send button to format".
but i don't know what the send button is...
help !
send buttom is the "green phone" buttom
in other word, the buttom you make call...
I have dopod c 800 which is broke wjile install the WM 6 ,now the condition just the startup screen with :
- dopod logo
- ipl 1.09.001
- spl 1.09.001
-gsm 02.69.90
i'm trying to get into bootloader by pressing camera and stylus or camera+comm manager + Stylus , but the screen was goin back to the logo of dopod again.see the figure
i think after get into bootloader i can install the original rom first then install again the wm 6
some body help please
Try holding the Camera Button after Reset, until Bootloader Screen appears, this must work out !
You have to hold both buttons (camera and commanager) until the bottscreen appears. only teh softreset button is pushed once.
DOn´t left the other bottons before bootscreen appears.
Good luck
Thanks
papamopps said:
You have to hold both buttons (camera and commanager) until the bottscreen appears. only teh softreset button is pushed once.
DOn´t left the other bottons before bootscreen appears.
Good luck
Click to expand...
Click to collapse
Thanks it works but pls find the way to make the gsm work after ugrading to WM 6 , nice system ..but sad always searching signal for the handphone.
Thank you
I just got x01ht from japan. It's stuck at windows mobile screen.
Herm200
ipl-1.01
spl-1.09
radio 1.14.00
Advices or just point me in the right direction
Thx in advance.
1st of all, try to remove battery for 10minutes and then switch on.
Thx, but that didn't work.
Hello,
Can you explain what was the last think you've done... because my crystal ball didn't work today I really hope that you didn't start to flash something before HardSPL, which you don't have.
Try to Hard reset the device:
Code:
Press and hold the Left SOFT KEY and Right SOFT KEY, and at the same time, use the stylus to press the RESET button at the bottom of your device. You will be presented with a menu saying 'press R to reset, X to exit', if you press R Your device will be set back to factory default settings. (The L/R soft keys are the "- -" keys just above the start and OK buttons)
If it still doesn't boot, continue with reading
The best thing you can do right now (if your device is still in warranty) is to take it back. If it out of warranty, then start reading here. Check SPL column where point at:
Code:
[B] 1.06, 1.09, 1.11 or 2.02 [/B]
Good luck
Hey guys,
I have a big problem with my HD2. I tried to install the NAND Android system but following problem occured.
I updated the ROM with the MAGLDR111 and on the PC it showed me the message, that everything´s ok.
But when the phone reboots it always show a white screen with the green HTC logo. Even when I hold the "end call" button, it will always shows the same.
When I try to update the ROM again, the phone won´t by found.
PLEASE help me out of this mess!!!!!
there's an entire forum dedicated to this. it's called HD2 Android Q&A
(edit)
be sure to hold the power/red button all the time. press and hold to start the phone and do not release it until you see the menu.
You do have HSPL 2.08.hspl on there, right??
best way to check is to go into bootloader mode
(take out battery, wait 10 sec. put it back in. HOLD volume down and briefly press the power/red button.)
the spl version is shown on the third or fourth line of text you see on the tricolour screen
Hi all,
I have this problem:
1) I tried install MAGLDR 1.13 on my phone and started ROM update utility. Update run everything ( On the screen was update from 3.15 to 2.00 ROM????? I dont understand)
2) After restart the white screen with HTC Logo is displayed and nothing - no response
3) The bootloader by pressing vol. down+ power does not work. I press everything (vol + and -) and still same - white screen with logo.
4) I cant use standart flash by PC conection, because phone didnt connect to PC.
Please, is there any help how to install bootloader and new ROM from SD card? Or other way how to repair it.
Thanks for any hint (except throw the phone from window )
PS: Please use some kind of easy English, my English is little poor and some technical words should be problem
Ive had the same problem, your bootloader is kind of broken! In 1 out of 50 tries you will reach the bootloader and then immideatly flash original spl and a stockrom.
Then send it to htc for warranty
Sent from my HTC HD2 using XDA App
boot
pres first on volume down button and then pressing power button . volume down button hold on to you in the colored screen. Once on colored screen with usb on pc and wm rom flashing.
DO this:
go to this : http://forum.xda-developers.com/showthread.php?t=945427
do step 1- 5 . Make sure you have HSPL 2.08 !
feel free to ask questions.