Orange SPV M3100 (HTC Hermes) Failed - 8525, TyTN, MDA Vario II, JasJam General

Hi
I have an orange SPV M3100 which died on me a few months back and I think its a repair job to be honest, It was running low on battery and I simply connected the charger and the phone immediately switched off and displayed a red led, i looked at the tip of the charger (Mini-usb type) and noticed that the bottom of the tip was slightly bent up as if it had been stood on or something.
Since then the phone wont switch on, charge or anything, its even stopped displaying the red led, I have tried the following.
1. Tried alternative chargers
2. Tried connecting to USB on PC
3. Tried resetting, removing battery and connecting to charger and putting battery on whiclst connected to power.
all of the above does nothing, I have thought about buying another battery but dont really want to go to the expense of buying a bettery to find that its completely dead anyhow
Any advice chaps?
Thanks
Will

I have the same problem, last night was browsing the web on wifi and the phone simply switched of, thought it might be the battery was dead so i hooked it up to the charger, the phone'sred led came up, came down this morning and it is still red..not green and it will not now power up....it must be something simple can any one help..?

ctasystems, if the red LED doesn't come on you may have fried you phone... If the power on the usb charger connected with the data part of the Hermes it may have fried the mainboard. I say this as this happened to my Imate Jam. The only thing I could suggest is if you know someone else with the same phone then try their battery and charger. If it works then its the battery &/or charger. If it doesn't then you've got something to sell on ebay - it will get you some cash to put towards a new phone...
hooperman, does sound like the battery BUT it sounds more like the battery is completely stuffed. As above, change the battery with a friends battery or go to the shop and see if they have a spare around you can try... The red LED means the hardware is still functioning so that would be my advice or purchase a cheap battery off of ebay.....
Cheers...

Related

Repair a Hermes

All,
I'm looking for a company which is able to clean and repair my HERM300 device.
It got wet and now when I want to charge it the led turns red.....
When I leave my device on a warm radiator it works and I can use the device...
But it seems to fail when it gets colder....
Any suggestions?
Cheers and thanks,
Hellejoep
hellejoep said:
All,
I'm looking for a company which is able to clean and repair my HERM300 device.
It got wet and now when I want to charge it the led turns red.....
When I leave my device on a warm radiator it works and I can use the device...
But it seems to fail when it gets colder....
Any suggestions?
Cheers and thanks,
Hellejoep
Click to expand...
Click to collapse
Can you say a bit more on "fail when it gets colder...."
I ask because soon maybe tonight I'm going to make a post on the charging and Red light problem but I'm just wondering exactly what you mean by "fail"
Cheers
Mike
mikechannon said:
Can you say a bit more on "fail when it gets colder...."
I ask because soon maybe tonight I'm going to make a post on the charging and Red light problem but I'm just wondering exactly what you mean by "fail"
Cheers
Mike
Click to expand...
Click to collapse
It blacks out as soon as I connect it to my activesync via USB....
Is it a short circuit?
Or something else?
Cheers,
Hellejoep
mikechannon said:
Can you say a bit more on "fail when it gets colder...."
I ask because soon maybe tonight I'm going to make a post on the charging and Red light problem but I'm just wondering exactly what you mean by "fail"
Cheers
Mike
Click to expand...
Click to collapse
I would like to add something, may be you already know, to red led knowledge. I have a car charger (just plain chinese USB charger with usb cable) When I connect my HERMES I could have 3 conditions: orange (charging) Nothing (not charging) or RED (?). If I soft reset, with charger connected, I ALWAYS have orange, after Windows Mobile screen, But if I disconnect and reconect I have ALWAYS No Light
connecting hermes to charger without battery also enables red light.
Charging Problems - Red Light of Death (RLOD)
Battery Charging Problems, in particular the RLOD so called because the phone refuses to charge and the red LED shows, indicating that the battery is NOT charging.
Background
Problems with charging are not HTC or Windows Mobile specific. Similar if not identical problems are reported across many models and platforms. The issues centre around the state of charge of the battery and the interpretive circuitry in the device and charger. Typically a device will show a Red light rather than an Amber charging light. (NB: RED LED always shows when battery is absent or fails to charge). see also http://forum.xda-developers.com/showpost.php?p=1076879&postcount=28
Getting the battery to start charging once this light is shown is not always straightforward and is as unpredictable and temperamental as priming a water pump (those that have done this will know what is meant). In other words, and to put it crudely, you need to kick start the system. Unfortunately those that have managed to do this have usually tried lots of things before it starts working again. This makes it hard to be absolutely certain about the solution other than perhaps the last 4 or 5 actions taken.
Those that have managed to recommence charging have not reported that the problem recurs on a frequent basis. (possible exception of in-car charging issue). This issue requires patience and time, (time maybe critical, it is possible the issue would resolve itself perhaps as charges dissipate within battery and circuitry involved). However the following points seem probable solutions and were thought to work by some who resolved the problem.
Failure to Charge (Red LED Lit when charger connected)
Causes of this problem are unclear, but in practical terms events leading up to this issue have included:
1
Leaving the phone on charge overnight (possibly but not necessarily with certain programmes or connections running) It seems a fault occurs in the charging system, which causes the battery charge to drain rather than increase. Resulting battery charge is very low. (Another Blog will be added concerning an Active Sync issue which can cause the battery to drain over-night through repeated connection attempts)
2
Through heavy use or not re-charging often enough so that the battery is permitted to reach a sub 10% charge (not precisely known but likely to be very low)
Possible Solutions:
A
1.) Remove battery
2.) Connect the phone to the charger or USB
3.) Insert the battery while connected to charger
4.) Red light should turn Amber
5.) Soft Reset
If this does not work immediately it is suggested that the battery be removed from the phone for around 1 hour and the above steps repeated.
OR
B
It has been found with some phones charging can be re-started by:
1 ) Remove battery
2 ) Connect charger (Optional. I would try this potential solution without the charger connected the first time I try this. If it fails to work then I would repeat the steps with the charger connected)
3 ) Holding the battery, line it up wiith the phone's battery contacts.
4 ) Move the battery rapidly on and off the contacts
6 ) Repeat the above until the Amber charging light comes on. So after perhaps connecting/disconnecting 20 times, insert the battery properly and give it a few seconds to see if the LED turns Amber.
7.) Soft Reset
NB: I have seen two reports where those attempting this report a fairly loud "pop" sound following which the phone began to charge. However in one case the person reported that they then had subsequent problems of signal reception on the phone and thought the popping sound may have been related to this.
OR
C
If your problems remain after trying this a few times you could always try the following to manually charge the battery a little (enough to let the phone charger circuit detect the battery is present when you put it back in)
1) Remove the battery from the phone!
2) Take 3 fresh AAA batteries in series (total 3 x 1.5V = 4.5V)
3) Connected the (+) wire to (+) on the battery
4) Connected the (-) wire to (-) on the battery
5) Hold this in place for 60 seconds.(possibly longer you are trying to charge it enough for charging circuitry to recognise there is a battery installed.
6) Put the battery in your phone
7) Switch on phone and start charging (via USB)
Hopefully you will get the Amber charging light.It may be worth repeating this a few times if not successful on the first try.
The electrical contacts are all important, poor contacts will render this a worthless exercise.
I leave it to you to decide how you connect the wires. If you have no other means you could enlist the help of someone to hold the batteries and wires together while you connect to the phone battery! Warning - Do not connect a mains based transformer to the battery with an incorrect charge rate (mAh) and voltage (V). Any attempt to force charge using mains transformers could be extremely hazardous (explosive). Only a qualified/competent person should attempt to charge the battery in this way. Similarly, even if you are using batteries to do this task, do not leave them connected for more than a few minutes and stop immediately if either set of batteries become warm.If the problem persists:The final resort - a new battery.
Mike
╤
Very good article Mike, I linked it on the Hermes problems wiki page
i just want to add my 2 cents to this, there was an earlier post on here that mentioned the car charger deal where it wont charge unless you turn the phone off, plug it in, then turn the phone.. right now i am on my 2nd 8525 and it has done this, but its not only the car charger (cheap belkin car charger) but it sometimes does this with usb cradle i got from ebay, i have opened the cradle and there isnt anything different, its a straight usb connection, hmm except now that i think about it there is a blue LED, but it shouldnt be drawing enough current to cause this. Also i have a motorola charger in my office that i used with my wizard (i believe output is slightly different, if i remember correctly its a .5 amp where as the HTC charger is 1 amp) but it also behaves in the same manner... the only 2 methods that work constantly and consistantly of plugging in without turning off is either the factory charger, or a regular usb cable on the pc..
just seems weird since all of these problematic situations worked fine on the wizard and i believe they both have the power requirements...
let me toss another idea in the fire here on this, something that just occured to me... i wonder if this somehow could be related to the factory installed driver for this. what made me think of this is how the battery meter only goes by 10%.. could this funky driver be the source of the problem?
shogunmark said:
right now i am on my 2nd 8525 and it has done this, but its not only the car charger (cheap belkin car charger) but it sometimes does this with usb cradle i got from ebay
Click to expand...
Click to collapse
If your cradle is not connected to your PC, or if your PC is off while you see the behaviour you described, then the likely reason is that pin 4 of the Mini USB connector isn't grounded on both your car charger and cradle. See here for more details.
Cheers
Daniel
pof said:
Very good article Mike, I linked it on the Hermes problems wiki page
Click to expand...
Click to collapse
Cheers pof.
Some of the type sizes are a bit strange (but readable!) serves me right for copying and pasting from Word formatting!
Tadzio's link is good/informative and I edited in a link to it in my post - though it's on this page anyway.
Mike
tadzio said:
If your cradle is not connected to your PC, or if your PC is off while you see the behaviour you described, then the likely reason is that pin 4 of the Mini USB connector isn't grounded on both your car charger and cradle. See here for more details.
Cheers
Daniel
Click to expand...
Click to collapse
cradle is connected to pc at all times, and i will deal with the car charger for now cause my HTC one should be arriving any week now, but thanks for the tip!
8525 (hermes) Charging may be voltage sensitive
I have noticed with my new 8525 (USA Cingular model of phone) that it came with a 5.5V charger. Whenever I connect to a 5.0 V USB source charging the phone is very "iffy". Given that the standard for USB is 5.0 V (4.75 - 5.25) there is a problem with the design. My question for the HTC crowd is can this be fixed via a ROM change or are we stuck with a bad design?
hellejoep said:
All,
I'm looking for a company which is able to clean and repair my HERM300 device.
It got wet and now when I want to charge it the led turns red.....
When I leave my device on a warm radiator it works and I can use the device...
But it seems to fail when it gets colder....
Any suggestions?
Cheers and thanks,
Hellejoep
Click to expand...
Click to collapse
http://www.america.htc.com/support/service-repairs.html
Since you got it wet, it is most likely not covered by the warranty, these and the numbers for out of warranty repair if you live in the U.S. I know that for cingular, you have to ship it to them yourself, and they will charge you a $28 diagnostic fee, before telling you how much is costs to fix the problem (if they even can)
heh here almost the same, providers are charging ~$29.5 USD as diagnostic fee but they are more polite, they first tell estimated costs, and only ask for the sum if you (usually) don't order the repair but need back your phone
Hellejoep:
if you are willing to send it abroad (inside EU) and you are either not need "overnight return" or such nonsense or cover the extra costs such operations really need, you may contact me. no diagnostics fee or anything such (though you will have a small loss.
about the charging problem:
the same issue occurs also in Wizard/Prophet, and Charmer (compactII) as well. though not in Magician, even so that they share the exactly same battery.
I believe it must have something to do with the charging controller. I don't have a disassembled unit at home with me now, but I suppose it should be a crap companion chip from Texas, to be interfaced with the ever-worst TI OMAP platform
(sorry, no hard feelings, pals, but someone using such one as an actual everyday phone must have some sorta mental problem )
strange battery issue
Hi all,
I've a similar issue with any charger.
It happened first with car charger (one cradle with an usb output): sometimes it charged, most of all it charged only when power was off.
Now I cannot charge with any method. (those described here: battery charging problems)
Usb cable (it's not original), original power supply, even with the y cable.
When i try to charge, it drain battery (i tried with a new one) and amber led blinks slowly instead to be firmly light.
There's anything I can do?
It's a SPV M3100 buyed two months ago on ebay.
I tried also with two roms WM6 official release ITA ver and Schap's 3.54b ITA ROM WM6
radio 1.48
Any suggestions?
Herm200/tytn problems
hi to all,
i read most of your post on possible problems with this PDA (HERM200/HTC TYTN).
i'll try to spent some few words to explain the story around my pda.
i live in italy and i bought the TYTN on december 2006 and for 6 months with his software problems i used it day by day in my business activity, untill one day, it falled down the ground from my and with all the leather cover (bundled with the pda, an hard black belt cover); then i took it and picked up a telephone number from my addres book and then putted it in charge for all the night; when, late in the morning, i took it, i noted that there was still the red light of the battery indicator and then PDA didn't turned on.
i tried to make soft/hard reset but nothing.
I carried to the italian warranty service of HTC and after 7 days they deliver to me the PDA in the same state that i carried; on the technical report there was: pcb damaged, battery connector pinouts damaged, pda not Repairable - out of warranty.
i thought: "i have had a lot of care for this PDA that still look like as new one"
and now i have a 700€ of unusefull PDA.
Last day i finally decided to open my PDA to find broken pieces and more.... but nothing.... i observed really well: NOTHING of wrong.
Now i will to know if somebody of you, can suggest me something to revive my PDA or suggest me any service center (affidable) in europe (not like the italian one) where to send it for maintenance: I DONT WANT TO THROW OUT MY PDA!
Thank you in advance for your attention and patience.
ps: sorry for my english, i hope it will be comprehensive.
therock-htc said:
Now i will to know if somebody of you, can suggest me something to revive my PDA or suggest me any service center (affidable) in europe (not like the italian one) where to send it for maintenance: I DONT WANT TO THROW OUT MY PDA!
Click to expand...
Click to collapse
If I understood you correctly, your TyTN still works - it just cannot charge the battery, right?
Then, probably one of the cheapest (although not perfect) solutions is to get a cradle that can charge a battery outside the TyTN (like this one on eBay). You will have to power down your TyTN, remove the battery and put it in the cradle every other night or so, so it's not very convenient. But it's cheap. Maybe you'll want to keep this as "plan B" in your mind while you look for a more perfect solution.
Cheers
tadzio
elehcimo said:
Hi all,
I've a similar issue with any charger.
It happened first with car charger (one cradle with an usb output): sometimes it charged, most of all it charged only when power was off.
Now I cannot charge with any method. (those described here: battery charging problems)
Usb cable (it's not original), original power supply, even with the y cable.
When i try to charge, it drain battery (i tried with a new one) and amber led blinks slowly instead to be firmly light.
There's anything I can do?
It's a SPV M3100 buyed two months ago on ebay.
I tried also with two roms WM6 official release ITA ver and Schap's 3.54b ITA ROM WM6
radio 1.48
Any suggestions?
Click to expand...
Click to collapse
Hello!
I had also a battery charging problems with my MDA Vario II (TyTN; Hermes; HERM300):
1. Charging from the AC mains supply with the original miniUSB 5V charger: no problems.
2. Charging in the car with the non-original car lighter miniUSB 5V charger: it was charged only when the phone was OFF; no charging when the phone was ON.
3. Charging with the USB-miniUSB 5V cable connected to the notebook: it is charging only when the phone is OFF; no charging when the phone is ON.
So I asked myself: what is the difference between all these three cases? They are all miniUSB 5V power sources... And I found out an answer: It should be a matter of the USB current amperage.
Original AC miniUSB 5V charger delivered with the phone is 5V/ 1A. When I have bought the car 5V miniUSB charger with the 1A (one amper) amperage - there is no problem with car battery charging anymore... ;-) The phone is charged either way: ON or OFF.
But is it possible to charge the battery correctly from the notebook? I think not, because I have no influence on the current value from the 5V notebook USB.
Previously I had MDA Vario (Wizard): in this phone there were no battery charging problems... I wonder why the are some with the Hermes...
Take care,
Przemo
Przemo_55 said:
And I found out an answer: It should be a matter of the USB current amperage.
Click to expand...
Click to collapse
This is not correct. The problem is well understood and has been discussed several times.
The key is that your device tries to sense what it is connected to:
- if there is USB data traffic, it concludes that it is connected to a computer. It will then negotiate the current (power) it can draw from the USB port with that computer.
- otherwise, your device checks if pin 4 of the connector is pulled to ground. If yes, it concludes that is is connected to a dedicated USB charger, and starts charging, consuming as much power as it needs. This mechanism seems to work only if the device is on - and sometimes not even then (bug?). I guess the mechanism is implemented in software, so it can't function when it is off.
- otherwise, it doesn't know what it's connected to. Could be a computer in stand-by that didn't power off its USB ports or something. Your device concludes it may be unwise to start charging (could, for example, drain the other device's battery).
The cheap after-market chargers do not connect pin 4 to ground (pin 5), so your device doesn't charge. If you are really good with a soldering iron, try connecting pins 4 and 5 of the charger's USB connector, and you'll see that your device will start charging with it.
Cheers
tadzio
tadzio said:
If I understood you correctly, your TyTN still works - it just cannot charge the battery, right?
Then, probably one of the cheapest (although not perfect) solutions is to get a cradle that can charge a battery outside the TyTN (like this one on eBay). You will have to power down your TyTN, remove the battery and put it in the cradle every other night or so, so it's not very convenient. But it's cheap. Maybe you'll want to keep this as "plan B" in your mind while you look for a more perfect solution.
Cheers
tadzio
Click to expand...
Click to collapse
Thank youu Tadzio,
but my PDA is DEAD !
I still don't try to charge the battery separetly.
The reason is that when i carried the PDA to service i leaved the PDA and Battery: i dont wanto to believe that service dont check the battery !??!?
However , i will try to charge the battery separetly and then i will know you the outcome.
Thanx and Cheers
Therock-htc

HTC not charging, battery dead?

Helloes guys and goils.
I have a HTC wiz, and for a good few weeks now I have had problems with it.
First off, It would NOT charge through the Wall Socket OR USB, I let it run down over XMas and it's not been the same again.
It just will not charge or come on.
When I plug it into USB it looks as if it is charging, with the Orange light and The power bar turns to the socket looking thing, but when I leave it to charge it just goes off and doesnt come back on.
When I plug it into the wall socket the HTC does not respond.
I have been asking my mate in work to put it in his and charge it via HIS wall charger, which has worked a few times, but I seem to be getting a very awful run out of my battery.
I am thinking it is the phone and NOT the battery as i first thought, I dunno, im scared of throwing up £30 notes on a new battery only to find it is the phone.
What do you guys think I should do?
I heard somewhere that it is a SOFTWARE based charge and not a hardware based charge, what does that mean?
DO u think a flash would help it? I cant see it myself.
Or is my HTC just goosed?
Well
I can speak from experience when I tell you my wizard nuked 2 batteries...
how I dont know.
Hopefully one of the gurus can shed some light on your situation
(¯`·._.·[LaZaRuS]·._.·´¯) said:
. . .
I am thinking it is the phone and NOT the battery as i first thought, I dunno, im scared of throwing up £30 notes on a new battery only to find it is the phone. . .
Click to expand...
Click to collapse
If you do replace the battery, look on eBay - I got a new 1250 mA battery (there are also 1100 mA versions, don't get that) for $13.99US including shipping - works great!
Make sure its nothing simple... Try the USB cable plugged directly into the computer without using a USB hub (if you are) and different USB ports on the back of the computer. Also try different outlets for the AC adapter. If still nothing else I'd even ask for help from your local cell phone store (put on a sad face) and see if they'll lend you a power cord and or swap out batteries to see if they can reproduce the problem on a different Wizard, battery, etc.
There has been many posts on this subject with several different fixes.. i would suggest searching and reading and you can find your answers
My case
Hi,
I had somewhat similar problem with mine. My porblem was that I bought the Wizard with a Motorola charger. It had the same mini usb plug and when I plugged it to charge, the led on the wizard was orange and the Wizard indicated its charging, but the moment I unlugg it, the battery indicator was coming back to its previous state. My solution is to use the PC USB to charge it, on a couple of occasions I had the battery completely drained and had to "jump start it" by connecting the wires from the usb directly to the + and - of the battery. Even used once my good old AA Ni-MH charger to jump start the battery and it worked.
So perhaps you are not getting power from the cable, why not try with different charger or charging from another USB source (PC).
Hope this helps
Just happened to me tonight. Thought that my Wizard was toast as well.
I merely took the battery out for 10 minutes, put battery back in, and plugged device into original wall charger. All is well now.
-Jeff

Mda will not turn on or charge

hey guys, my mda will not charge or turn on. when plugged into a/c the indication light does not come on. i have switched batteries with my other mda and still unable to turn it on. i have done searches but have not found any relevant info. does anyone have some insight?
No charge
I have exactly the same problem...
My phone was charging and my washing maching caused a power surge and the only thing that seems to have been affected is my HTC Wizard! I've ordered a new battery so I'm waiting for this in the hope that this is the problem... If not - HELLO INSURANCE!
I'm running into this also. When I plug in the charger, the LED turns green, then red and thats it.
anyone? may have to do some brain surgery on the mda
You haven't told us anything. What were you doing before it quit just turning on? Have you tried to do a hard reset on it, soft reset, or put it into bootloader? Were you trying to flash a rom when it quit working? Was it on an original rom or custom one (and which rom was it?). Did you upgrade it in any way (load software)? Did you do a soft reset and it quit working, or did it just die while you were doing stuff? Or did it just not turn on the next time you tried to use it?
Like I said, you haven't told us anything other than it won't turn on with your battery or another battery. Information is a good thing
For me...I didnt do anything. It was on and sitting on my desk. The battery was a bit low. I went outside to check the mail, came back and it was dead. I tried turning it on, the boot screen came on and then off...never to turn on again at all.
No custom roms or software or anything. I couldnt find my wall charger so I took my old razr charger plugged it in, nothing, LEDS wouldnt even come on.
So I took it to a Cingular store and they had an OEM charger there. They plugged it in, the Orange LED came on for a second, then turned red and would just sit there. Not even turning on.
But what ROM were you on? THere were numerous issues with the early Cingular (and other) ROMs where once the battery got below a certain percentage it would not charge anymore. There are tricks here and in HowardForums for how to jumpstart your battery (using a 9V battery or a wall charger with bare wires). Can't say if thats what this issue is, but it might help.
So you said you took yours to the Cingular store. Did they replace it? You didn't finish your story.
i know, im sorta interested in what happened
OK here's the solution.
First of all, be aware that the MDA can NOT charge unless the OS is fully loaded. If for whatever reason your battery gets fully depleted, you have to do the following (it involves ruining a 5 $ cable and doing some surgery):
- first, go out and buy a new USB-to-mini-USB cable, unless you have 2 already (or one and the original charger)
- take out the battery
- take the USB-to-mini-USB cable, cut off the mini-USB plug and expose the four wires
- strip the red (+) and black (-) wire and twist the copper ends of each wire
- now CAREFULLY attach the right wire to the right connector on the battery (so + on + and - on -) and tape it there so it stays firmly on
- put the cable in your (running) PC or put the charger in the wall socket
- let the battery recharge for an hour or so, then put it back in the Wizard and reboot
- now when it is fully rebooted, you need the second cable to charge your Wizard completely, the way you're used to.
Worked for me! I've kept the ruined cable, just in case it happens again.
Good luck!
fixed
Luckily enough an old friend of mine had an 8125 that finally broke to crap, so he gave me his battery. I popped it in, voila! Not only did it load, but it comtinues to charge. I was worried the phone was bricked.
But this is definately a battery issue. Thanks for all the help and info guys. It's good to know this thing wont charger unless the OS is fully loaded, didnt know that.
May I just check, is this charging issue (when the OS is loaded) only an issue on the 8125's? I have an o2 Mini S and just as a check powered it down by holding the power button but while in this state if I connected it to a charger the orange LED still came on to indicate it was charging but in the off state.
hey guys sorry i did not respond earlier i have been away for sometime. well my phone was working all night but when i woke up it would not turn on. i plugged in the charger into the wall and none of the lights came out. took the battery from my broken screen mda and still did not turn on. the phone had the xelencin 2.26 rom update. programs i had installed were:
spb shell
spb diary
spb pocket plus
battery status - overclocked @ 195 i believe
most programs were installed on a 2gb minisd card.
again the phone was working fine the night before and upon waking up it owuld not turn on or even charge. i am currently at work but i will try out the previous suggestions as soon as i am home and will post back.
SteRo said:
OK here's the solution.
First of all, be aware that the MDA can NOT charge unless the OS is fully loaded. If for whatever reason your battery gets fully depleted, you have to do the following (it involves ruining a 5 $ cable and doing some surgery):
- first, go out and buy a new USB-to-mini-USB cable, unless you have 2 already (or one and the original charger)
- take out the battery
- take the USB-to-mini-USB cable, cut off the mini-USB plug and expose the four wires
- strip the red (+) and black (-) wire and twist the copper ends of each wire
- now CAREFULLY attach the right wire to the right connector on the battery (so + on + and - on -) and tape it there so it stays firmly on
- put the cable in your (running) PC or put the charger in the wall socket
- let the battery recharge for an hour or so, then put it back in the Wizard and reboot
- now when it is fully rebooted, you need the second cable to charge your Wizard completely, the way you're used to.
Worked for me! I've kept the ruined cable, just in case it happens again.
Good luck!
Click to expand...
Click to collapse
i see 6 connectors on the battery and left is red and right is black but there r 6 connectiors so which 1 i should plug in the neg and pos sign is like right in between..so can u upload a pic so i can see?
The pins that you need to connect it to are the end ones, the red wire goes to the one thats at the end with the plus symbol, and the black at the opposite end with the minus symbol. I just tried it and it works great.
doesnt work, maybe i bricked my phone
Klong4 said:
The pins that you need to connect it to are the end ones, the red wire goes to the one thats at the end with the plus symbol, and the black at the opposite end with the minus symbol. I just tried it and it works great.
Click to expand...
Click to collapse
I just recovered two regular batteries and and extended battery using this process. Too late though. I have another battery coming in from WM Experts. Any way the process is flawless and the charge time would depend on how long the battery has been low. Another possibility is may be the battery has run its life.
Fixed it!
as stated elsewhere the charger has to be 5v ish and 1A i'd tried other ch1argers nd everything nd then i found a charger 4 my old phone which was an spv c550 which was 1A plugged that in and after a couple of seconds the good 'ol orange charging indicator came on.. after which it booted up perfectly! so happy it's working now hope this helps some1!
Callum

XDA Mini S....Dead....no really

Hi all,
Right, the battery on my XDA Mini S was getting low, so I plugged it into the wall charger (not an official one, its a motorola mini usb charger 5v, 850mA)
It was left charging for a couple of days. I think? Someone could have turned off the switch? But the switch was on this morning
Anyway.....It doesn't boot, no signs of life at all, if i plug it into the wall charger then there's no lights.
Doesn't even go to boot loader.
No response when plugging it into USB.
I've tried hard reset, no nothing.
It's weird because its been working perfectly.
I've been googling and reading the forums here.
I've had a go at "jumping" or reviving the battery. Maybe I'm doing it wrong?
I bought a 9v battery, took apart a mini usb cable and removed the red and black wires. I've been holding the wires from the 9v battery connecters to the tips of the + and - plates.
Still nothing.
Can anyone suggest anything?
Surely it can't just become a paper weight suddenly?
This hasn't happened from flashing either.
I've also tried another charger, which didn't work, so the charger isn't the problem.
Wohoooooooooooooooooooooooooooooooooooo!
Fixed it.
I tried "reviving" the battery again.
Except this time I tried connecting the + and - to different plates.
My sticker on the back of my battery lies, and tells me the wrong + and -
So I googled what an XDA Mini S battery should REALLY look like....voila!
better buy a 1AMP Wall charger and don't let the battery completely discharge.
Yeah, I heard this problem with a friend of mine as well. Battery ran out completely and it wouldnt charge at all (seems that it only charges if the phone is on, so, yeah, figures).
My suggestion on that case would be to try something else to charge the battery alone, dont know a specific charge but sometimes little things like putting it in the freezer for some time works to give it a tiny little life back, enough to turn on the phone, you never know.
hey i have same problem with that
im using 9 v batteries and connect to mda batteries
but still nothing
what must i do. . . . . .
would someone help me
i try all but still nothing
2 days a go my mda can on but only bootloader and then off
till now im so confused
please help me
i run out of battery too and now can't find anyway to turn on my mobile to charge. need some help too. hix
someone help us........................
ok, found the way and revive my phone
1, take a usb cable and cut it
2, there are 4 wires: red,black,white and green
we need red and black so cut those white and green
3, see on your pin, there are 6 bronze square, the frist and last have + and - icon on it
4,connect usb cable to r computer
5,red wire to the square has (+) icon
black to other
wait about 30s
6, place pin to yout phone and power on, u have some second to recharge it
nice, i'm charge my phone
it's not work for me
stiil freeze

Atom life only recharges when turned off

Hello,
my problem is strange.
When I turn off my Atom Life it can be charged (USB, External Power Supply).
Red indicator light on.
When turned on (in use) it does not charge. The charging symbol in the status line shows the unit is connected to external power, but the red indicator light is off, and power continuously goes down.
I already tried a hard reset, but that did not help.
Does anybody have an idea?
Sorry, I forgot to mention that everything with charging went fine earlier (until some weeks ago)
charging
same thing with my XDA ATom dude
I have ordered a new battery for mine at ebay (did not arrive yet).
Maybe it helps.
Otherwise ...
Ok, the battery came in and it does not change anything.
Still the same issue.
So I am gonna litter it...
bye bye
New info,
there seems to be a bad contact at the USB connector.
If I connect the USB cable and hold the plug in a specific angle, then the charging light (red led) turns on).
Brought the device to a friend of mine. He's good at electronics and tries to figure out and fix the usb connector.
wait and see
Siyan said:
New info,
there seems to be a bad contact at the USB connector.
If I connect the USB cable and hold the plug in a specific angle, then the charging light (red led) turns on).
Brought the device to a friend of mine. He's good at electronics and tries to figure out and fix the usb connector.
wait and see
Click to expand...
Click to collapse
any news for your problem ??
i'm having this problem too
i brought used one and seems the battery is almost dead and can't charge when device is ON
Thanks!
I got a used atom life and bought a new main battery for it. Charging via USB cable connected to my notebook is working fine. Using the (wall socket plugin) power supply with the same cable it behaves the same way you described it. It starts charging only when the device is turned On and back Off. In my opinion the power supply is the reason. Maybe it is to week ar has some sort of security switch build in, which is protecting it against to high power consumption.
In my case it was definitely not the charger. I tried several ones and they behaved all the same (the original one wrked for long time).
It is the device itself.
I had it sent to a friend who was able to open it and a have a look at it.
The USB plug itself was a bit loose. But soldering it again did not fix the problem.
There seems to be a micro break of a wire on the mainboard (which is multi layered). So no real chance to repair.
I replaced my device by a HTC Desire which was available in Germany very very cheaply (you don't want to know the price because it wuld be too frustrating).
So goodbye Atom Life.

Categories

Resources