Related
Hi,
I have tried to upgrade my HTC 3300. I get as far as a white screen on my PDA, but after this i loose the connection with Windows Mobile Center and the machine automatically disconnects.
Then i get the error on my PC:
Error 260
Please help and e-mail to [email protected] if you have a sollution.
Kind regards
Michael
miriedl said:
Hi,
I have tried to upgrade my HTC 3300. I get as far as a white screen on my PDA, but after this i loose the connection with Windows Mobile Center and the machine automatically disconnects.
Then i get the error on my PC:
Error 260
Please help and e-mail to [email protected] if you have a sollution.
Kind regards
Michael
Click to expand...
Click to collapse
Update UPSL v0.1 by Pof
Link here :
http://forum.xda-developers.com/showthread.php?t=311403
And try again..!
Cheers...!
Hmmmm.
What do you mean with:
Update UPSL v0.1 by Pof
Michael
Pof is a user
UPSL is an unlocker utility so you can flash alternative ROM's
check the link - very informative.
reflashing your phone usually takes a weeks worth of reading if you care for your device.
And read it :
http://forum.xda-developers.com/showthread.php?t=312052
maybe it help you..!
Is there an easier way to explain this - Sorry i'm quite good working with my PC, but this was a bit greek:
All you need to do is:
1. Remove your SD card
2. Do a hard reset or clean storage (some programs like battery status block full access to your device)
3. Connect your mobile to PC and make sure that activsync connection is established
4. Start to flash your device with USPL, when DOS part end and your mobile switch to bootloader mode vista will find new device and start instaling new drivers.
5. Wait till vista finish installing new drivers and unplug your device, do a soft reset
6. Next step is to change vista drivers to xp, to do this you need to fallow this instruction:
http://www.mrvanx.org/cms/index.php?option=com_content&task=view&id=23&Itemi d=27
7. After switching the drivers plug your artemis again and install USPL, there should be no more problems with connection lost (errors 260, 270)
8. When USPL instalation will finish you can flash any rom you want to your arte
Succesfully tested on my T-Mobile MDA UK now I've got WM6 WWE.
Thanks pof for your great release
That explination is about as clear as it gets in 'phone talk'.
Perhaps elaborate a bit on what is exactly, or what step is, throwing you off.
Windows XP
Hi again.
Would i solve the problem if i just installed it from an Windows XP machine at work?
One final thing - Do you know if the GPS will still be working afterwards.
Have a good night from Oslo - Norway
Kind regards
Michael
I am using Windows Vista Ultimate and O2 Orbit trying to upgrade to WM6 and have a problem
I have turned off all my running programs on the pc
Have set up a Sync with the O2 orbit.
When I run the USPL utility all goes ok while in the Dos part when it switches to the second part Graphical it losses the sync connection and I am unable to resync.
I have had to disconnect the orbit from the pc and turn on and off to get it working agn
So I am at this moment unable to upgrage any help would be app.
thanks
s2tephen said:
I am using Windows Vista Ultimate and O2 Orbit trying to upgrade to WM6 and have a problem
I have turned off all my running programs on the pc
Have set up a Sync with the O2 orbit.
When I run the USPL utility all goes ok while in the Dos part when it switches to the second part Graphical it losses the sync connection and I am unable to resync.
I have had to disconnect the orbit from the pc and turn on and off to get it working agn
So I am at this moment unable to upgrage any help would be app.
thanks
Click to expand...
Click to collapse
READ THIS TREAD IT WILL HELP YOU
http://forum.xda-developers.com/showthread.php?t=317589
Dear all
I try to update my PPC 6600 from WM2003 2nd edition to WM6. I download and run WM6 OS 5.2.2000 (Build 20000.1.0.0.PV.HAT). After I try to finish the last step of the installation which is to cool reset the PPC, there are 4 color bands and only show "NO GSM", "D 5.70.11 WWE". I try to turn it off, but doesn't work. I try to connect back to PC, but PC can not find this device
Please help
http://wiki.xda-developers.com/index.php?pagename=BA_FAQ_STUCK_AT_STARTUP
imatrix said:
http://wiki.xda-developers.com/index.php?pagename=BA_FAQ_STUCK_AT_STARTUP
Click to expand...
Click to collapse
I have tried, but not work, no format, no reset, stay the same
here is the message from the program. please help
USB>
USB>set 14 0
HTCST ÚÈHTCEUSB>set 14 0
HTCST ÚÈHTCEUSB>task 28
DOC_format_HW+
DOCInfoTableinitHW+
Binary0:dwSize=80000
BINFS0:dwSize=0
FAT0:dwSize=1000000
FAT1:dwSize=EA0000
All:dwSize=1F20000
USB>task 0
USB>
I am very sorry, but I need help.
I am unable to fix this.
I am trying my best to follow the instructions and dont know where am i going wrong.
Like U said,
I went again with the Multi Port TTY utility and in the new USB text file window, ((stopped the wcescomm.exe application from taskbar)
I tried entering
set 14 0
USB>task 28
USB>task 0
USB>
Saved the file as USB
The phone in the cradle was still showing USB v1.02
I took the phone out of the cradle, removed the battery and inserted it back into the cradle
and i again starts showing USB v1.02
Where am i going wrong..
I also tried
USB>set 14 0
USB>task 28
USB>task 0
USB>
but in vain...
Please help in resolving this
I found http://forum.xda-developers.com/archive/index.php/t-273871.html online and the problem is almost identical as mine. Please help
i think u can flash it again
woi700 said:
i think u can flash it again
Click to expand...
Click to collapse
What do you mean flash it again?
It can not be detected by activesync
cables
Something like that happened to me a while back where i couldnt connect. The problem wasnt the BA but was the cable connections- usb cable connections. It stills happens today where i get a bad connection and i have to play around with the usb that is plugged into my laptop. Maybe you should check out how loose your usb connection is--try moving the cable around.
shazzy84 said:
Something like that happened to me a while back where i couldnt connect. The problem wasnt the BA but was the cable connections- usb cable connections. It stills happens today where i get a bad connection and i have to play around with the usb that is plugged into my laptop. Maybe you should check out how loose your usb connection is--try moving the cable around.
Click to expand...
Click to collapse
I have tried many time, but not work
reflash
get into boot loader mode, connect directly to pc with good direct usb connection, (screen should state, USB from SERIAL on connection), reflash.
ensure SD card is removed beforehand.
AbuGWM5 said:
get into boot loader mode, connect directly to pc with good direct usb connection, (screen should state, USB from SERIAL on connection), reflash.
ensure SD card is removed beforehand.
Click to expand...
Click to collapse
What do you mean reflash?
Does it mean that Reinstall the WM6, or install other OS like WM5?
However,Without activesync how can I do that?
OR reflash mean formart?
I try to fomart my ppc, but stuck in the white screen
Note: I have tried the following
http://wiki.xda-developers.com/index...UCK_AT_STARTUP
If you can get USB connection to your device, you can just try to reflash with same WM6. best of lucks.
restart your PC
Try reinstalling active sync on your PC or laptop and then shutdown your PC or laptop and then restart it. Then try connecting your BA afterwards.
shazzy84 said:
Try reinstalling active sync on your PC or laptop and then shutdown your PC or laptop and then restart it. Then try connecting your BA afterwards.
Click to expand...
Click to collapse
I did what you said, but my PC is still unable to detect my pocketPC.
In the pocketPC bootloader mode, I can see it change from serial to USB after I connect the usb bundle. What should I do?????
king2004c said:
Dear all
I try to connect back to PC, but PC can not find this device
Please help
Click to expand...
Click to collapse
try to disable windows firewall and any other firewall then try...
i have same problem my device can't connect to pc when i disable ISA firewall my ppc connected .
AddAn
addan said:
try to disable windows firewall and any other firewall then try...
i have same problem my device can't connect to pc when i disable ISA firewall my ppc connected .
AddAn
Click to expand...
Click to collapse
I have followed what you say, but still not work
I hear some people say that I can reflash the rom.
But
1. I don't know which rom they mean, my orginal one or updated one?
2. How can I get my original rom?
Someone say that if I try to connect via activesync under PPC bootloader mode, I could not see any connection in activesync, but I will hear some connection sound, then I can reflash my rom
But
1. How can I do anything if I can not see any connection in activesync
I have done what people say about using mytt1.24.
But,
What should I expect to see?
king2004c said:
Dear all
I try to update my PPC 6600 from WM2003 2nd edition to WM6. I download and run WM6 OS 5.2.2000 (Build 20000.1.0.0.PV.HAT). After I try to finish the last step of the installation which is to cool reset the PPC, there are 4 color bands and only show "NO GSM", "D 5.70.11 WWE". I try to turn it off, but doesn't work. I try to connect back to PC, but PC can not find this device
Please help
Click to expand...
Click to collapse
go here ftp://xda:[email protected]_1.15_Type_II/BA Radio 115 THIS WORKS.rar then use this to load your gsm extract BA Radio 115 THIS WORKS.rar somewere on your computer put your ba it to bootloader mode then put i into its craidle then run MaUpgradeUt_noID.exe wait till upgrade is done then take out of the craidle press reset button dont worry about activesync connecting
or not
update information
I tried to upgrade my win2003 2nd edition in ppc 6600 to WM6, but it seems that WM6 won't work with ppc 6600. Then,
1. I download the WM5 rom from http://wiki.xda-developers.com/index.php?pagename=Helmi
2. Try to reflash the PPC
3. I see that the PPC response
4. Try to do the reset after finished upload rom
5. Four color strip screen & "NO gps" and "5.02... WWE"
6. Try to restart again, and wait, result is the same
7. Try to go to bootloader mode, use mtty, do "set 14 0", "task 28", "task 0", PPC still keep the same. I have tried all reset, hard reset, etc
8. *** Try to reflash the PPC again, I find out that there is no current ROM when the ROM upload program try to read my current PPC condition.
PPC6600 is a CDMA device and not a GSM, so you tried to flash a wrong ROM, sorry friend.
April 1 said:
PPC6600 is a CDMA device and not a GSM, so you tried to flash a wrong ROM, sorry friend.
Click to expand...
Click to collapse
could you please tell me where I can find the corret rom?
After I read http://wiki.xda-developers.com/index.php?pagename=HTC_Blueangel_WM6_WizzardUpgrade4
It says The WM6 does not work on PH20A2 (Harrier) (Audiovox PPC-6600 / PPC-6601 / XV6600)/ CDMA device! <-- that is my mistake
My mistake steps:
1. upgrade 2003 2nd edition to WM6 (I see 4 color strip with "NO GSM" at the bottom, stuck in there. The PPC will stop if I remove the battery for a few seconds and put battery back)
2. use mytt <-- may not hurt (I see 4 color strip with "NO GSM" at the bottom, stuck in there. The PPC will stop if I remove the battery for a few seconds and put battery back)
3. Do hard reset, format the PPC (stuck in white screen, then do soft reset. The PPC will ""NOT"" stop if I remove the battery for a few seconds and put battery back)
reflash
Have you tried re-flashing with the original ROM?
AbuGWM5 said:
Have you tried re-flashing with the original ROM?
Click to expand...
Click to collapse
What do you mean reflash?
Does it mean that Reinstall the WM6, or install other OS like WM5?
However,Without activesync how can I do that?
OR reflash mean formart?
I try to fomart my ppc, but stuck in the white screen
You got to revert back to WM 2003 SE with your original OS.
April 1 said:
You got to revert back to WM 2003 SE with your original OS.
Click to expand...
Click to collapse
I try to connect my phone under bootloader mode. However, both my computer and my notebook can not detect my Pocket PC.
king2004c said:
I try to connect my phone under bootloader mode. However, both my computer and my notebook can not detect my Pocket PC.
Click to expand...
Click to collapse
put you ppc into bootloader mode then put it into the craidle then go to startmenu on you computer
then go to computer then right ckick youll see properties click it
then system properties sould show click hardware then device manager
do you see windows CE USB Devices if you do then click it then you sould see microsoft USB Sync
if it dose then go here
http://wiki.xda-developers.com/index.php?pagename=BlueangelFAQhave
rickwyatt said:
put you ppc into bootloader mode then put it into the craidle then go to startmenu on you computer
then go to computer then right ckick youll see properties click it
then system properties sould show click hardware then device manager
do you see windows CE USB Devices if you do then click it then you sould see microsoft USB Sync
if it dose then go here
http://wiki.xda-developers.com/index.php?pagename=BlueangelFAQhave
Click to expand...
Click to collapse
I tried to upgrade my win2003 2nd edition in ppc 6600 to WM6, but it seems that WM6 won't work with ppc 6600. Then,
1. I download the WM5 rom from http://wiki.xda-developers.com/index.php?pagename=Helmi
2. Try to reflash the PPC
3. I see that the PPC response
4. Try to do the reset after finished upload rom
5. Four color strip screen & "NO gps" and "5.02... WWE"
6. Try to restart again, and wait, result is the same
7. Try to go to bootloader mode, use mtty, do "set 14 0", "task 28", "task 0", PPC still keep the same. I have tried all reset, hard reset, etc
8. *** Try to reflash the PPC again, I find out that there is no current ROM when the ROM upload program try to read my current PPC condition.
Btw, I post the question to the FAQ too
try to take out first SD Card and SIM CARD from your BA first before connect to your notebook/PC
king2004c said:
I tried to upgrade my win2003 2nd edition in ppc 6600 to WM6, but it seems that WM6 won't work with ppc 6600. Then,
1. I download the WM5 rom from http://wiki.xda-developers.com/index.php?pagename=Helmi
2. Try to reflash the PPC
3. I see that the PPC response
4. Try to do the reset after finished upload rom
5. Four color strip screen & "NO gps" and "5.02... WWE"
6. Try to restart again, and wait, result is the same
7. Try to go to bootloader mode, use mtty, do "set 14 0", "task 28", "task 0", PPC still keep the same. I have tried all reset, hard reset, etc
8. *** Try to reflash the PPC again, I find out that there is no current ROM when the ROM upload program try to read my current PPC condition.
Btw, I post the question to the FAQ too
Click to expand...
Click to collapse
You did very stupid thing, you have flashed GSM based rom to a CDMA device, the only thing you can do is to use WM2003SE, flash your device with its original or any CDMA (Harrier) based WM2003SE rom
Quick Howto:
Put your device in bootloader mode, put it on the cradle, start the upgrade including radio (the same version can be flashed on top of the previous one), this will fix your device, if it does not then after successful WM2003SE upgrade do the MTTY "set 14 0", "task 28", "task 0".
Keep me posted if you have problem
P.S.
WM5 and WM6 does not work on Harrier (CDMA Blueangel) device, i hope my instructions to help you to have at least usable device
xplode said:
You did very stupid thing, you have flashed GSM based rom to a CDMA device, the only thing you can do is to use WM2003SE, flash your device with its original or any CDMA (Harrier) based WM2003SE rom
Quick Howto:
Put your device in bootloader mode, put it on the cradle, start the upgrade including radio (the same version can be flashed on top of the previous one), this will fix your device, if it does not then after successful WM2003SE upgrade do the MTTY "set 14 0", "task 28", "task 0".
Keep me posted if you have problem
P.S.
WM5 and WM6 does not work on Harrier (CDMA Blueangel) device, i hope my instructions to help you to have at least usable device
Click to expand...
Click to collapse
I can reboot my device now, but the bluetooth does not work (all other main function seem works OK). I hope there is some solution that help me to fix the bluetooth becuase I have a external bluetooth gps receiver which I need to use it with my ppc all the time. Please help
king2004c said:
I can reboot my device now, but the bluetooth does not work (all other main function seem works OK). I hope there is some solution that help me to fix the bluetooth becuase I have a external bluetooth gps receiver which I need to use it with my ppc all the time. Please help
Click to expand...
Click to collapse
Please understand what xplode wrote to you, you can not use the GSM ROM on your device, so dont try to check bluetooth etc, go back and reflash your device with the original ROM following what explode said above. Dont you want to save your device?
April 1 said:
Please understand what xplode wrote to you, you can not use the GSM ROM on your device, so dont try to check bluetooth etc, go back and reflash your device with the original ROM following what explode said above. Dont you want to save your device?
Click to expand...
Click to collapse
I have already find a CDMA rom. Now the only problem in my phone is bluetooth
Well describe the exact problem, BT does not turn on at all, or maybe it returns error of some kind?
Please be more specific
xplode said:
Well describe the exact problem, BT does not turn on at all, or maybe it returns error of some kind?
Please be more specific
Click to expand...
Click to collapse
So far, I can use the phone without any problem. Previously, I tried to upgrade my phone because I want to use bluetooth headset to listen music. That can only be done in WM5 or later. Now I reinstall my CDMA version of WM2003. I find out that the bluetooth does not work due to expire of lincese key. Does anyone have any suggestion how I can over come it? I just want my phone back to exact a few day ago. Thanks
thanks
lincese
Someone has posted the attached file and said that it can fix BT license expired error. I have not tried it myself since I dont face such prob, so use it on your own risk.
To use it - extract archive to your PocketPC and run EXE file.
meehaa said:
Someone has posted the attached file and said that it can fix BT license expired error. I have not tried it myself since I dont face such prob, so use it on your own risk.
To use it - extract archive to your PocketPC and run EXE file.
Click to expand...
Click to collapse
Thanks, but does not work on my PPC6600
Hi
I'm new to all this so please be gentle.
I have a Orange spv m500 that I'm trying to upgrade. I run the Rom upgrade and it connects, tells me that it is upgrading from one version to the new version. The phone then goes into the bootloader mode. Usb at the top of the screen and v1.00 at the bottom. After about 2 mins I get a 101 connection error.
Phone now just stuck in the bootloader.
Please help
Kerr
mccollk said:
Hi
I'm new to all this so please be gentle.
I have a Orange spv m500 that I'm trying to upgrade. I run the Rom upgrade and it connects, tells me that it is upgrading from one version to the new version. The phone then goes into the bootloader mode. Usb at the top of the screen and v1.00 at the bottom. After about 2 mins I get a 101 connection error.
Phone now just stuck in the bootloader.
Please help
Kerr
Click to expand...
Click to collapse
try to Kill/end process "wcescomm.exe" on Windows Task Manager, and reflash again
Thanks for replying. I have checked the Task Manager and I do not have wcescomm.exe running. My OS is Windows Vista.
Cheers Kerr
use windows xp, windows vista is not compatible
mccollk said:
Thanks for replying. I have checked the Task Manager and I do not have wcescomm.exe running. My OS is Windows Vista.
Cheers Kerr
Click to expand...
Click to collapse
so your PC using Windows Vista OS, no wonder you did not find wcescomm.exe !!
for synchronization you could use WMDC 6.1 for Windows Vista
here, report the successful flash the rom in Vista ~ http://forum.xda-developers.com/showpost.php?p=2640169&postcount=6
upgrade done
Hi Thanks to all that provided advice. I managed to get an old xp laptop and got connected and upgraded. Cheers