Hi,
I know it is not a big problem, but. My neo wont charge just turn on red led for a sec, and then nothing. I can't connect via USB becouse battery is empty. When it is on a charger I can get bootloader mode and I can do a hard reset. Can somebody help me with flashing from a SD card? What to use ROM dump or *.nbf file from O2 update?
IPL 2.15.0001
SPL 2.15.0001
If you can enter bootloader whilst charging through USB, you can recover it by reflashing. Check the Wiki http://wiki.xda-developers.com/index.php?pagename=Prophet_recovery for a how to.
i can not charge it through USB.
Can somebody please upload a dump rom from Xda neo, or if somebody have race edition will be much better.
Thank you,
Igor
Related
I have a new Prophet (JAMin) and it does not start, even when charged. All that happens is the lights at the top flash, the screen blinks and then no more.
Any ideas, as I need the device later!!!
Does it show any serial number on the bottom of the screen or does it just show a blank screen.
What you could do is remove the battery, SD card out and leave the device like that for about an hour or so. After an hour just insert the battery (not the SD card) and then try charging again. Let it charge for about half n hour and then try switching on the device. Most likely, your device will now wake up, if it doesn't then you will probably need to wait till the amber light turns green indicating a full charge. Try switching on the device again, if still no luck, then you will need to take it down to a service centre.
It works when using power adapter, but not on usb
The prophet does start up when using the power adapter, but not when on the USB. Have left it 'charging', but the charge light is not on.
USB only provides a trickle charge and hence is not the best solution for "waking up" a device. Always make sure that you charge your device through the provided AC adapter. Only in cases of emergency or when synchronisation allow USB charging.
No charge light
No charge light is on. Is that right?
If there is no charge light, that means its not charging to begin with. Can you check if the USB port you are charging from is functional by attaching another device to it. Incase the USB port is fine, try charging from a different USB port; if it still behaves the same way, i suggest you take it down to a service centre. Its quite possible that the charging port on the Prophet is damaged.
sam_sykes said:
I have a new Prophet (JAMin) and it does not start, even when charged. All that happens is the lights at the top flash, the screen blinks and then no more.
Any ideas, as I need the device later!!!
Click to expand...
Click to collapse
Mine used to be like that after I installed spb plus previous version, it wont start at all...I had to switch to a new machine (for free) coz it was only day-2 after i bought the device (nice service btw).
Cheers!
I Have an SPV M600 which when switched on the screen blinks and then powers off, no charging light will only power up with the charger plugged in not with the usb data cable, i used a file called hard_SPL-G4 since then this error occured i think its the software program loader.
I cant reflash via active sync because the device powers off without the AC charger. i do have SD cards, but im unsure how to flash from SD i want my original spl version back and a better OS.
IPL 2.21.0001
SPL 2.21.01ip
GSM 02.69.21
OS 7.7.7.7
I can get to the tricolour screen bootloader with charger plugged please help any advice?
these are the original settings i think
IPL 2.10.0001
SPL 2.10.0001
GSM 02.07.20
OS 2.10.1.22
Once it is in bootloader, can you switch it to the USB cable?
Q: Once it is in bootloader, can you switch it to the USB cable?
A: no it switches the power off when i unplug AC but i can get to the windows OS if i power on with AC..? but flash via activesync no AC on reset.
I do have two SPV M600s im not touching the working one. but would like to fix the other one. SD Flash would help possible corrupt OS or SPL i think?
i can gain access to bootloader but i dont know how to initialize the NBH rom,
i could start the extrom cabs which had an autorun with a list of execution
i updated the rom Mysterious_1.0 all went ok i think
then i ran hard_SPL-G4 i had a lot of errors about sleep4.exe not win32 i think.
i am running x64 pro and upon reset all i had was an occasional screen blink and weak flashing orange and blue led.
ive tried different battery and a different USB to miniUSB. the active sync does take long time looking for changes on OS.
from usb i hold camera button and click reset switch it goes to USB bootloader for a second then off
if theres anyone out there who knows how to reflash the SPL version and a new OS for an SPV M600 english lang from an SD card please link files and explain the process in as much detail please? thankyou!
i did also update the radio version GSM could that be a cause!
The radio version should have nothing to do with it...
I am fairly sure there is something on the wiki about flashing from a storage card, but you need to make the dump of the ROM from the working device, so not much help there...
If you can get into bootloader whilst it is plugged into your computer, it's a very easy problem to fix...
I have decided to find the pinouts for a 4.5V charger (it should be 5V but im not destroying original) and a spare USB-miniUSB attach the power terminals from the charger replacing the miniUSB charge terminals, which should allow me to go to bootloader with USB present. i will post my results in here soon
about accessing bootloader
Hi i have just executed the jump spl files on my problem device and its taken me to a white screen with usb data cable, which i heard is the bootloader really and used tera term pro to dump rom etc. its seems to of hanged at the minute does it take a while to write?
im guessing i could go into the white screen mode and reflash an original orange rom?
New Original OS installed
Hi ive successfully installed a new OS so i presume the white screen is a bootloader. still my problem of powering off upon boot exists, so using this method i want to change the details below
OLD SETTINGS
IPL 2.21.0001
SPL 2.21.01ip
GSM 02.69.21
OS 7.7.7.7
NEW SETTINGS
IPL 2.10.0001 check
SPL 2.21.01ip SPL 2.10.0001 wanted
GSM 02.69.21 GSM 02.07.20 wanted
OS 2.10.1.22 check
Can i reinstall the wanted SPL/GSM from the white screen loader? does anyone know where i can get the files. SPV M600
Repaired 100%
I did it, its fixed charges now from USB data cable. and can enter tricolour bootloader. the problem was something wrong with the spl flash process ive redone that no errors excellent. im happy now
Will a ROM flash now?
Hi,
after the download new ROM my MDA was fired!!
First I download a customized ITA rom and after, because the MDA work very slow, I downloaded the latest T-mobile ROM.
Now the MDA do not power up and do not charge the battery.....sems dead.
Can I recover it?
just an idea but I would start by trying to charge it with the wall plug that came with it, not a computer usb cable - if the battery is all the way dead it will not charge from the computer. If the light comes on, let it charge for a while and then try it out. If not I would try to hard reset while it is plugged in. If none of this works, enter bootloader mode and then connect it to the computer, and hopefully it will go into bootloader mode and you can flash a new rom.. If you need more details on how to do any of this, let me know, and please let me know if it works!
Hi....you fine.
I have recharge the battery and dowloaded the original Tmob rom.
Now is strange..
Same time power up...and same time no.
The ipl is 1.06 and spl is 1.03!!
My Qtek 9100 is dead also. I have the 2.24 ROM and it has been running great. I cant power it on and the light doesnt turn on when its plugged in. The battery is definitely not dead. Suggestions? TIA
try this...
try the suggestions listed here
however be warned that any of these will delete any and all data that may or may not still be on your device and restore it to just the fresh ROM...
Hi,
I have flash the rom 1.6 Tmob (IPL 1.06 SPL 1.03) but the MDA restart in loop mode!!
My phone powered up today. It's been sitting on my night stand for a week and it turned on today! Everyday I have tried to turn it on but I haven't had any luck until today...weird!
Hi There.
I really need your guys help!!!
a few weeks ago, i lost my battery and i recharged it using USB cable and battery.
It was boot up and i was testing it and keep reboot up. It was work!!
But after a hour left, can not boot up again.
I recharged my battery using USB cable ( cut it off and using red and black wire)
I did hard reset. ( Still not work)
try to flash rom, but can not do it. I was in Bootloder and when i attached USB cable to my kjam, it show off that USB on the screen with 3 colors.
I tried all the way, but still can not boot up.
My PDA show blue screen with I-Mate and
IPL 2.16.0001
SPL 2.16.0001
GSM 02.20.11
OS 2.16.9.1
Please guys help me to boot up my Kjam.
Please.
[email protected]
I tried restore ROM, but still can not boot up.
Please guys help me. T.T
Few days ago my Wizard died all of a sudden. When turned on it only gets to the point when it shows "HTC smart mobility" and stays there. So not even to the screen with IPL, SPL. I tried soft/hard resetting, playing with battery but it was all no go, same.
I can get to the red-green-blue bootloader screen however, shows IPL 3.08, SPL 3.08. If i connect via USB cable to computer, bootloader screen shows "USB" on bottom. The ROM on the device was TNT's (not sure which version), Windows Mobile 6.1. It worked for ages without any problems with this ROM before this.
ActiveSync does not recognise Wizard at all, I cannot establish connection and therefore downgrade/upgrade the ROM becouse upgrade programs (for exmaple with ROM got originally with the device) say they cannot contact the device.
What are my options, please help.
hy
in my opinion , it is normal for active sync to not recognize your phone , because it's not turn on properly ,i mean it only recognize the phone when you enter windows mobile.
if i were you i would try to flash any rom i like and see if it works. i hope this helps
But ROM upgrade/downgrade program requires ActiveSync connection to run and I can't establish it...How to solve the situation, please advise?
when you are in bootloader screen and your phone is connected to the pc by usb cable just start the downgrade/upgrade program and it should work.
i did that. rom update utility complains that it cannot connect with mobile...
that was tried with:
1. official t-mobile ROM that was on the device when I got it
2. CUSTOM__RUU_Wizard_1050412_WWE_101_11210_WWE ROM
my IPL and SPL versions now are 3.08
sorry , i can't think of anything that might help you.
same problem
phones a brick.
I can get to the bootloader , i can even perform a succesful hard reset.
But it doesnt get recognized by the computer in bootloader mode. is there any way to flash the rom if the computer doesnt recognize the device?
regards
Try this look for nbd v8.1 or v8.3 .
hold the camera button and do a soft reset but keep holding the camera button until the 3 color screen comes up it should sync your phone then run the nbd rom or original cingular ship rom like this one ** RUU_Wizard_225111_22511102_022511_CWS_WWE_Ship_1 ** i prefer original then other but that's me. Hope this help you.
I BRICK MY HTC WIZARD... CAN SOME ONE HELP ME PLEASE???? I OWN A HTC WIZARD FROM CINGULAR 8125 POCKET PC. RECENLY I TRYED TO FLASH MY POCKET PC BUT SOMETHONG HAPPEND.... IT JUST STAYS ON THE CINGULAR LOGO..
IPL 2.21.0001
SPL 2.21.O1ip
GSM 02.25.11
OS 2.18.0.0
AND IT JUST STAYS THERE.....
PLEASE HELP......
brick...
chipis said:
I BRICK MY HTC WIZARD... CAN SOME ONE HELP ME PLEASE???? I OWN A HTC WIZARD FROM CINGULAR 8125 POCKET PC. RECENLY I TRYED TO FLASH MY POCKET PC BUT SOMETHONG HAPPEND.... IT JUST STAYS ON THE CINGULAR LOGO..
IPL 2.21.0001
SPL 2.21.O1ip
GSM 02.25.11
OS 2.18.0.0
AND IT JUST STAYS THERE.....
PLEASE HELP......
Click to expand...
Click to collapse
I try to answer... (sorry for my bad english)
1. Make sure your battery up to 50%, 100% is recommended...
2. turn off u'r PPC
3. press camera,talk, and power button at the same time for a second until your display show 3 colour....
4. plug your cable data from PPC to desktopPC, and make sure your display show "USB", and try to re-flash with other ROMS.....
Good Luck
Thank for answer me and understand what i ment
Ok what software you recoment?. I do not know if i have a unlocked phone but i do know that i used it with t-moble even that my pocket pc is for cingular, i went to those stores that unlocked phones and that it
Help.
I have a Wizard G4 and I tried to install a WM6.5 ROM (TechTeamup Mega Wizard rom) from the default WM5. I did not put in the hard-spl (as I now read) before I tried to flash. Now when it boots, I go strait to the flash screen (tri-color) screen. I tried ot run the hard-spl-G4 and it says it cannot find a device. I have tried to re-flash back to WM5 ROMs that I have found, however it says it cannont complete "ERROR 296: UPGRADE ONLY, which makes me belive I need a G4 Wizard ROM that is a full (not upgrade). What steps should I take now to revert back to a WM5 so I can re-try the "unlock" hard-spl proceedure to make the phone WM6 compatible?
Anyone have any suggestions?
IPL 2.28.0001
SPL 2.28.0001
Download the original ship ROM for your phone.
Turn the phone off.
Press and hold the Camera key, now insert the USB cable, Keep holding the camera key until you get the boot loader screen.
Now run the ROM update to flash back to WM5.
ricozy said:
I try to answer... (sorry for my bad english)
1. Make sure your battery up to 50%, 100% is recommended...
2. turn off u'r PPC
3. press camera,talk, and power button at the same time for a second until your display show 3 colour....
4. plug your cable data from PPC to desktopPC, and make sure your display show "USB", and try to re-flash with other ROMS.....
Good Luck
Click to expand...
Click to collapse
I brick my wizard too... What happened was I flashed my own cook of m6r5 it say successful but on reboot, it shows htc logo then stays ay tricolor screen:
IPL 2.26
SPL 2.26
Bootloader wont work..tried many times but I cannot connect to PC...
Tried ricozy post above, can access 3 color... but still cannot connect to PC...
Please help...anyone..
IF u can enter bootloader...connect to pc...u shud c "USB" written in the left bottom corner ...then flash a rom as usual