Database Users

Prophet IPL/SPL 3.08 won't Downgrade

Hello everyone,
I am here to ask for some help from the experts.
I already read a lot in this forum but could not find any working solution.
My Prophet was upgraded to IPL/SPL 3.08 and won't turn on unless I connect +5v pn pin 1 and ground on pin 6. Doing this I can go to tricolor screen.
I tried to flash IPL/SPL 2.20 but after the reboots it comes back with IPL/SPL 3.08.
Any ideas how to downgrade the IPL/SPL ?
Best regards to you all and a warm thank you for the quality post in this forum.
Adias

Downgrade IPL/SPL 3.08 sorted
I sorted this in a moment of clarity.
Steps:
1. Got a working WM5 rom into the Prophet
2. Connected ActiveSync
3. Got prophet SOFT SPL into the phone device root.
4. Run SOFT SPL. Got a white Screen (Witch is normal. This is the SSPL bootloader screen)
5. Flashed IPL 2.20... OK
6. Flashed HARDSPL... OK (I supose SPL 2.20 can also be flashed)
Thevice unbricked and working fine.

congrats and well done
its even more satisfying when you solve it your self yes?

Can you please provide links for the SOFT SPL and HARDSPL files? Thanks men
asrdias said:
I sorted this in a moment of clarity.
Steps:
1. Got a working WM5 rom into the Prophet
2. Connected ActiveSync
3. Got prophet SOFT SPL into the phone device root.
4. Run SOFT SPL. Got a white Screen (Witch is normal. This is the SSPL bootloader screen)
5. Flashed IPL 2.20... OK
6. Flashed HARDSPL... OK (I supose SPL 2.20 can also be flashed)
Thevice unbricked and working fine.
Click to expand...
Click to collapse

Question hard spl
I already have de SPL 2.26 before I had 3.08. the question is, Do I have to run the hard slp? Thanks.

Did I brick it....???

Hello all!
I need urgent help with my T-Mobile MDA Vario I (Wizard 200) G4 (2006):
I wanted to upgrade to WM6 and used Hard SPL to do that. Read all the tutorials.
After applying Hard SPL the boot screen read:
IPL: 2.21.0001
SPL: 2.21.Olip
GSM: 02.19.11
OS: 2.24.2.5
Then I flashed the ROM with "RUU_WM6_XB_FUSION" .....
Result: At reboot it hang in the old T-Mobile boot screen stating:
the above IPL and SPL but
GSM: 02.47.21
OS: 10.0.0.0
The only thing I can do now is:
go into boot loader mode by pressing camera and stylus
and reflash it with the same RUU: it still hangs....
Not possible to reconnect to Active Sync anymore so cannot remove Hard SPL to go back to original OS with Soft SPL....
SO WHAT NOW???? Please Help, I am at a loss, just bought it...

you need to install a non official windows mobile 5 rom that doesnt have spl / ipl built into them (ex: wizard love rom) google it.

Brought back to life!
Many thanks: I did what you suggested and it's back amongst the living!
Now I need a stable G4 proof WM6 RUU....any suggestions???
fhjmgb72

elf reboot over and over

i flashed with swiftblades V4 blue. the flash worked good, as it was suppost to but now the elf reboots itself ever 5 to 10 minutes or so. Also there is no entry for Rogers Data Plan in the network wizard. is there a way I could add that to the wizard?

Sorry, I have no much ideas to help, but talking about Wizard setup..
Can you download a more recent rom like onyx?
Cheers.

I had the same problem, if you have IPL and USPL 3.07 or higher you just have to downgrade the IPL and USPL tot 2.28.0000 or lower

Yes the problem in IPL this rom is an upgradre of an old rom (i think based on WM6) so you have two choices either change IPL or change rom

IPL 3.14 makes my ELF battery dried after power-off?

I've been reading on the upgrade to 6.1 with various cooked rom, and decided to go with Tessa 4.5. Since it is required to go with IPL 3.10/SPL 3.10, i went from original ROM and upgrade one step at a time, to 1.17, 2.26 and 2.28, and 3.10 (both IPL and SPL). Then I noticed after 3.10, i cannot boot up. This is before I upgrade to Tessa, just upgrading IPL/SPL.
When in 2.26, everytime upgrade completed, reboot went fine. But after 3.10, it went wrong. I tried to fix it with upgrading IPL only to 3.14.
It still wont boot up after power down.
So I downgrade to IPL/SPL 2.28. The SPL went down, but IPL stays at 3.14, and the problem continues. I can upgrade to Onyx, but everytime I power down, i have to flash with IPL/SPL 2.28 to make the ELF boot up. When I get to the OS, i check my battery is 0%.
Is IPL 3.14 the culprit? If yes, how do I downgrade it? using elf-uspl and/or Rom Utility gives same result: IPL stays at 3.14.
Help?

Update:
i was able to flash with elf-uspl using ipl/spl 2.27/2.28.
Now i have onyx junior with the ipl/spl combination above.
But it is still having problem when I turned off the device. It won't go pass smart mobility, instead it just shut down again. I have to take out the battery, put it back in, then reflash with rom utility (with any spl/ipl below 3.0) then it would restart and go pass smart mobility and enter the OS.
What gives?

Update2:
After trying to downgrade and upgrade, I use the original HTC Touch ROM, Windows 6.0. Still the problem appear. So I decided to go with elf-uspl and get the SPL back to 1.11000 (which was the initial working setup). Then I flashed the IPL to 1.17002.
Now, with IPL 1.17002 and SPL 1.1100, everything went back to normal.
Is this mean I cannot use SPL above my initial setting? Obviously the newer cooked rom won't accept these number, as it needs to have 3.10 minimum?

Update2:
After trying to downgrade and upgrade, I use the original HTC Touch ROM, Windows 6.0. Still the problem appear. So I decided to go with elf-uspl and get the SPL back to 1.11000 (which was the initial working setup). Then I flashed the IPL to 1.17002.
Now, with IPL 1.17002 and SPL 1.1100, everything went back to normal.
Is this mean I cannot use SPL above my initial setting? Obviously the newer cooked rom won't accept these number, as it needs to have 3.10 minimum?
I finally settled with IPL/SPL 1.19 since this is the only setting that would still boot to OS after I Power Off the device. Now looking for Win 6.1 coked rom that would accept these IPL/SPL setting...

Update2:
After trying to downgrade and upgrade, I use the original HTC Touch ROM, Windows 6.0. Still the problem appear. So I decided to go with elf-uspl and get the SPL back to 1.11000 (which was the initial working setup). Then I flashed the IPL to 1.17002.
Now, with IPL 1.17002 and SPL 1.1100, everything went back to normal.
Is this mean I cannot use SPL above my initial setting? Obviously the newer cooked rom won't accept these number, as it needs to have 3.10 minimum?
I finally settled with IPL/SPL 1.19 since this is the only setting that would still boot to OS after I Power Off the device. Now looking for Win 6.1 cooked rom that would accept these IPL/SPL setting...

[Q] i-mate K-JAM stuck at windows mobile 6 splash screen

as above, it has
IPL 2.26
SPL 2.26
GSM 02.25.11
OS 10.1.0.811
i tried soft resetting but still the same problem, is it bricked??
please help

Your phone is not bricked.
Try hard resetting the phone if that don’t work install the original ROM and start over.[FONT=&quot][/FONT]