Sorry if these questions have been asked before, but i need clear answers please...
1) Will Upgrading my ROM to B&B 4.1 invalidate my warranty?
2) Do i need to USPL my P3300? - it's a HTC branded device (not from other networks)
3) The following instruction were for B&B v.2.0 , will they work for 4.1?
Code:
1. download the file Artemis_USPL.zip
2. unpack into the folder c:\USPL
3. download the file ARTEMIS_Black_Blue_v2.zip
4. unpack into the folder c:\ROM
5. soft reset your phone and have it charged over 50% (I have it fully charged)
6. wait until the system starts on your Artemis
7. turn on flight mode (probably not necessary, but I wanted to minimize any risks)
8. connect your Artemis to PC with a USB cable
9. wait until ActiveSync icon in your tray (lower right corner of your windows desktop) turns from gray to green. If you connect your Artemis for the first time to PC, you do not need to set up synchronization, just click "cancel" on the first screen of "Synchronization Setup Wizard"
10. while ActiveSync icon is green, run c:\USPL\start_uspl.exe
11. a DOS screen will pop up with the text "Initializing: 0.." in the bottom indicating probably seconds from the start (it stopped around 70 in my case after about 1.5 min)
12. DOS screen disappears and PDA Phone ROM update utility pops up
13. at the same time, your Artemis turns blank (orange/green LED turns off as well)
14. tick the check box next to " I understand..." and then click Next
15. tick the check box next to " I completed..." and then click Next
16. a box saying "Verifying information on your PDA..." pops up
17. on the next screen click Update button
18. next screen says "Upgrade to ... image version 9.99" - click Next
19. Next screen says "You are now ready to update..." - click Next, a window with a blue progress bar appears with a text "Updating ROM image..", it quickly runs to 100%
20. next screen says "Congratulations! ..." - click Finish
21. your phone turns on and boots into your old system, however it should be CID unlocked now
22. your Active Sync should reestablish and icon turns green again
23. do not touch anything (phone or USB cable) and run C:\ROM\ROMUpdateUtility.exe (make sure activesync icon is green)
24. PDA Phone ROM Update utility window appears, tick the check box next to " I understand..." and then click Next
25. tick the check box next to " I completed..." and then click Next
26. a box saying "Verifying information on your PDA..." pops up
27. on next screen click Update button (says "Current information...")
28. next screen says "Upgrade to ... image version BnB2.0" - click Next
29. Next screen says "You are now ready to update..." - click Next
30. a window with a blue progress bar appears with a text "Updating ROM image..", your Artemis will have light gray screen with blue progress bar showing the progress of flashing - do not touch anything and wait (it took 2-3 minutes on my 3 years old PC)
31. next screen says "Congratulations! ..." - click Finish
32. your Artemis turns on and starts booting, you can disconnect it from PC now
33. the boot screen remains the same (T-Mobile in my case), so do not panic!! it is normal
34. wait until calibrate the screen appears, calibrate, choose time zone and you are ready to use your new OS
35. let me know if this manual was clear enough, whether it helped you and please suggest potential changes for improvement
4) If i brick my device, will i be able to reflash the original ROM back on to it?
5) If i do upgrade will the GPS work properly? - and how would i get TOMTOM on it?
Sorry if you have seen these questions many times before,
All help will be greatly appreciated, Thanks
1) Yes
2) I don't know... but I think you'll must do it
3) Lastest ROM are easyer... just an setup file whitch to all...(your instructions are OK, i did it with my first Upgrade)
4) Yes, IF YOU HAVE THE ORIGINAL ROM FILE (I did it)..
5) Some ROM can have a problem on GPS device... there a patch... i found it in this forum.. TOMTOM or Ather GPS SoftWare are work properly (tried with TOMTOM 6.0&6.03 / iGo 2006 / MioMAP..)
PS : PDA soft ware are faster on WM6, but i find GPS synchronization is Slower..
thanks for the reply, you helped me out loads.
Related
good day to you all
i want to backup my kjam and i downloaded the wizbackup and there is somthing worng:
i am connecting my kjam to the computer with the windows mobile device center ( the new program that come's with vista) and it says "connected" and then run the wizbackup :
1.the first step it says to choose the option i want , i choose 1(backup rom(auto cid unlock)).
2.it says please connect your wizerd to the computer make sure activsync is connected and press enter....
3.now i wait untill i see another menu (the screen is showing some 4 colers like red green blue and in the res section it says IPL 2.16 nad RUU and SPL 2.16 and in button it says USB)...and in the menu it says "when mtty will start choose usb and press enter......nothing happend so i press enter....
and then i see some pop up that named "open port setting" so i serch for usb but there is no usb there only com1 and com2.....??????? so after a long story someone can help me?
I am in the same exact boat that you're in and I really hope that someone answers your post. In the mean time I will continue to search for an answer and if I find it, I'll return to this thread and post it for you. If you should happen to find the answer, could you please do the same?
Happy searching.
I have a cid and sim unlocked T-mobile mda running Wm5. Problem is now when I boot up the device it hangs @ the T-mobile boot screen. I have
ipl 2.26
spl 2.26
Gsm 02.25.11
os 2.26.10.2
Any help plz guys
EDIT... FIXED THE PROBLEM Found this in and it worked...
Ok here´s how I done it.
First, I must explain what was the problem.
After update the firmware (not actually upgrade, I had the phone full of trash, so I decided to reflash same firmware v2.18 PTG), the Qtek 9100 / HTC Wizard freezed at 2nd splash screen (the one that shows OS versions IPL version, ect). Tried many different versions, upgraded to 2.24, 2.25, downgraded even to 1.6.7.3, but always same problem, freezed on second splash screen. I read many topics on xda-dev, and seen some people with same problem. Apparently there was 2 solutions. 1- send phone back to warranty. 2- write backup ROM from SD in bootloader.
Passed more then 15 hours asking for this SD backup everywhere, and COULDN´T find any help. Apparently no one had this "SD dump ROM Backup".
So here´s how I solved my problem
1- I tought that a SD backup was needed, and yes it is. But u can use your own phone and your own SD to do it.
2- Get a clean SD card (in qtek 9100 / Htc Wizard case is MiniSD) with 128MB (some people say 64MB, but I personally used a 128MB, maybe a 64MB is enough)
3- Kill (task manager) wescomm.exe (this is related with activesync installed on your PC). Insert the blank SD card on the phone.
4- Get your phone in bootloader mode. Like this : Phone powered off, press Camera button + Power On, will enter in bootloader mode (RGB screen).
5- Now connect your USB cable to your phone. And start MTTY_updateROM.exe (http://wiki.xda-developers.com/uploads/romupdate.rar). After open, on Port selection, choose \\.\WCEUSBSH001 and press OK. A window will open with a blank sheet.
6- Type "r2sd all" and hit enter... wait to the end (at end shows "cmd>"). On your phone screen u can follow backup progress... small bar will appear down the RGB screen.
7- Power off the phone (or remove battery), enter bootloader mode (camera button + power on) and this time RGB won´t appear right away. Will ask if u want to "download SD image", press voice dial button to agree, and writting will begin. Wait to the end. Power off and power on normally. Now your phone should be working ok. Not even needed to reflash the phone after this.
Thanks to all and hope this helps more people with this problem
5- Now connect your USB cable to your phone. And start MTTY_updateROM.exe (http://wiki.xda-developers.com/uploads/romupdate.rar). After open, on Port selection, choose \\.\WCEUSBSH001 and press OK. A window will open with a blank sheet.
The only Port Selections available are:
COM1
COM2
COM3
COM4
COM5
What am I doing wrong?
i got the same problem too
only com1 and com2 r there
pleace help me
Yes please someone help!
I want to try this, too, but my mtty tool only shows some com-ports and not WCEUSBSH001 ! what's wrong?
Does this work with mini sd cards bigger than 128 mb, too? is there a limit?
ok, I have the right port in mtty tool now, but...
when I enter "r2sd all" and press enter it says this:
r2sd all
***** user area size = 0x77F00000 Bytes
R2SDBackup() - Download type = 5
usTotalBlock = 1 sizeof(SDCARD_SIGNATRUE_TABLE)=512
You didn't get the proper security level to download a specific image
Cmd>
what can I do?
any help is greatly appreciated!
Guys,
I have a standard O2 Orbit here and I am looking at installing this TouchFLO ROM I've seen on this forum. However I'm a bit worried about bricking my phone.
Can somebody just give me a few steps to follow. I've searched but I have to say I got a bit confused when reading about CID locks etc...
Any help greatly appreciated.
You have to run USPL first (USPL by "Pof")
You will find it at STICKY Section.
Mostly all the ROM here lately allready built in USPL. so it will automatically takes you to the next DSUU windows.
but if you really wants Step by Step:
-----------------------------------
1. Make sure your Activesync is version 4.5 (or Above).
2. Refresh your PC by "RESTART" and enter WindowsXP again (just to make sure your PC running fresh).
3. Refresh your PDA by "Soft reset" your PDA, wait until finish (just to make sure your PC running fresh).
4. Make sure you have 80% or more Battery.
5. Connect your device to PC via activesync using USB only.
6. wait until "connected" or "Syncronized".
7. Enter folder USPL.
8. Double click "start_uspl.exe" (small yellow ball icon).
9. Black screen will appears... start uploading 10%..20%.... until 100%
10. Update windows will appear... Follow instruction by clicking "NEXT" or tick "YES I AGREE..bla bla" check box.
11. The progress bar will appear... wait until Finish.
12. Do not unplug the USB cable or your PDA become brick.
13. When finish your PDA Restart itself... and normally enter the today screen.
14. If not working try it again from Step: 5 (sometimes need to try more than one)
13. If your PDA restart itself and Show the SPL number is changes then CONGRATULATIONS you have finish install the USPL.
Next step is to Upgrade your ROM using DSUU (its on the ROM folder)
14. install DSUU is simple just double click "ROMUpdateUtility.exe"
15. Update windows will appear & follow instructions.
I Hope it helps..
best regards,
Wens
I'm assuming it won't differ if I'm using Vista as my client and not Win XP?
Also, is it possible to do this Via Bluetooth as my bloody USB cable isn't working correctly!
Vista not using Activesync, but WDMC
you can download at microsoft Website.
Upgrade ROM only can be done using USB cable. other won't work.
Good Luck!
- Install Windows Mobile Device Center 6 for Windows Vista
- On your artemis launch Bootloader and connect with your PC using usb cable. (For bootloader press Voice Dial + On/off button at the same time till you see a multi colored screen)
- Do exactly what the tutorial describe here: http://www.mrvanx.org/cms/index.php?option=com_content&task=view&id=23&Itemid=27
- Your driver is changed so you can cid unlock your artemis now, do this by using USPL. (download below + manual). Remember to use the same usb port where you changed the driver from, otherwise the connection get lost and you have a update error.
- You can now search for a cooked rom of your choice and simply flash it by running the RUU.exe.
I did Slider's
...I followed the instructions but after step 9
(9. Black screen will appears... start uploading 10%..20%.... until 100%) nothing happened on my phone.
Any ideas. No "Next" or anything...the update rom utility just fired off (running the USPL from the Touch Rom directory
the prob seems to be vista......
or it could be the o2 offical WM6 rom
mine will upload the offical O2 rom but everything else fails.
people tell me im doing it wrong but have followed the driver swap step by step on 2 diff vista machines with no joy.
just borrow somebodyelse Windows XP Machines.. that'll do.
I need help .
When i start my 02 atom pure, it opens but it stops on the WINDOWS MOBILE page and it asks me to 'tap the screen to set up your mobile-based device". if i do this it goes to the 'align screen" then i follow the instructions. but it just goes on and on....
I also did the "press camera+reset" wherein it goes to the black with white text asking to choose 1 or 2
If i choose #1: Module rebugging mode. it will say reboot for next usage. then I would reboot. I reboot by doing the soft reset. Then it goes to Windows Mobile - but it would say again Tap the screen to set up your windows mobile-based device.
If i choose # 2 (Jump to DM). it goes to the Windows Mobile page again and asks me to do the.... tap the screen
Other things I did were:
1. I tried reinstalling again the XDA-Atom-Eng (i did this when i first had my 02 phone).
2. I also tried to download the Windows phone 6.5 from http://forum.xda-developers.com/showthread.php?t=629499 I saved it in my storage card. But it seems it didn't apply when i opened my 02.
need HELP terribly. Thanks!
maybe that ROM you have been Install....not for o2 XDA-Atom Pure...that's your problem
hi
my name is shekhar
please get me wm 6.5 to my htc diamond
i want to upgrade from wm6.1 to wm 6.5
please
How to Install or Update your Windows Mobile?
Please Follow Below Orders :
Please Follow Below Orders :
1. you need a PC
2-1. If you have Windows XP -> Setup ActiveSync 4.5 from Here
2-2. If you have Windows Vista or 7 -> Setup Windows Mobile Device Center from Here
3.If you use manufactured ROM(Orginal WM6.1 ROM OR Official ROM) -> Install Touch_Diamond_-HardSPL_OILNEX From Here
How To Install HardSPL on Touch Diamond?
-> After Downloading and Extracting this file
you Must connect your Touch Diamond to your PC with its Cable
Let your PC Connect to your PPC with ActiveSync or Windows Mobile Device Center
Find HardSPL Folder and Run ROMUpdateUtility.exe
At Appeared Windows Page By ROMUpdateUtility.exe Accept Check Box and Click Next Button
Warning : Don't Unplug in Touch Diamond's Cable , Diamond's Battery Must be Charged More than 50%
Then you can see this Message on your PC->"verify the information on your PDAphone...Please wait"
After That you can see Setup Page on your PPC with 4 colors and on the White Color Part ,you can see USB (Notice : You can See Setup Page with Holding Sound Decreasing Button and Pressing Restart Button togather and Release Sound Decreasing Button Until Appearing That Screen)
Clicking Update Button And Next Button After That
And in Finally you can See Two Process Bars are Processing in the Same Time One of them on your PC and Another on your PPC and Restart your Device automatically.
I congratulate, your Touch Diamond Has Been Unlocked now you can install any ROMS That you Want
4. Downloading WINDOW MOBILE 6.5 WITH HTC SENSE 2.5 from Here ( you can See its Pic Here)And Extract this file
5. you Have this folder With two Files CustomRUU.exe And a File With NBH suffix , IF this Folder Dosn't have CustomRUU.exe Download it from Here And Put it to this Folder
5. Run CustomRUU.exe -> Keep Clicking Check Box Button and Next Button until Appearing That Message Again : "verify the information on your PDAphone...Please wait"
6. Clicking Update Button And Next Button After That
7. you can see again Two Process Bars are Processing at the Same Time On your PC and PPC
8. After Finishing ->your PPC Restarts Automatically Again And you Have WM6.5+HTC SENSE 2.5 ON YOUR TOUCH DIAMOND
9. Enjoy. (This ROM Has Been Made And Cooked by donsalari So Much Fast and Stable and Also Really Nice)
Hi guyz!
I have heard it said some of the ROM updates cause some technical failure...like GPS failure or G-sensor....
I wanna ask someone, who have tried this ROM if its ok and will not make any defection!
Thanks in advance!
workes great