Killed my Alpine - PDA2, XDA IIi, 2020i Software Upgrading

Hi,
Yesterday i tried to upload new firmware to my XDA11i.
During this my lappy crashed (bloody Vista)
My screen just shows "serial" when i try to power up, The green LED doesnt flash or go yellow when put in the Base unit.
Any help would be apreciated.
Chris

Your dead Alpine...
999grub said:
Hi,
Yesterday i tried to upload new firmware to my XDA11i.
During this my lappy crashed (bloody Vista)
My screen just shows "serial" when i try to power up, The green LED doesnt flash or go yellow when put in the Base unit.
Any help would be apreciated.
Chris
Click to expand...
Click to collapse
Your in bootloader mode. You may be able to resolve the problem by removing the battery and letting it set of a few hours. This will run down the backup battery and kill the memory, or try a hard reset. However, you will lose all you data. Try reading some of the posts on this website. Good luck...

999grub said:
Hi,
Yesterday i tried to upload new firmware to my XDA11i.
During this my lappy crashed (bloody Vista)
My screen just shows "serial" when i try to power up, The green LED doesnt flash or go yellow when put in the Base unit.
Any help would be apreciated.
Chris
Click to expand...
Click to collapse
HI....Bro I have the same situation like you when upgrading the firmware using vista. It just killed my alpine and then only show serial. I used mtty program and set 14 0. You have to disabled the activesync setting for no usb connection when upgrading the firmware using UpgradeUt_noID. Windows vista really sucks big time when upgrading firmware. I just revert back to XP where it is more stable.

Thanks
Still no joy, but thanks for the replys.
Vista came with lappy and as its still under warenty i can't downgrade to XP.
Does not seem to want to hard reset, Left it with battery out all night.
Getting worried now!
Any other sugestions would be welcome.
Chris

999grub said:
Still no joy, but thanks for the replys.
Vista came with lappy and as its still under warenty i can't downgrade to XP.
Does not seem to want to hard reset, Left it with battery out all night.
Getting worried now!
Any other sugestions would be welcome.
Chris
Click to expand...
Click to collapse
there is one VERY easy way, take the update files/dock/xda2i to a friends house and use there xp machine, job done, or take it to work with you and do it there. no worries. as long as its still in boot loader mode you will not have a problem.

999grub said:
Hi,
Yesterday i tried to upload new firmware to my XDA11i.
During this my lappy crashed (bloody Vista)
My screen just shows "serial" when i try to power up, The green LED doesnt flash or go yellow when put in the Base unit.
Any help would be apreciated.
Chris
Click to expand...
Click to collapse
The fix is here:
http://forum.xda-developers.com/showthread.php?p=1739989

Related

My SVP M600 phone got stuck at Starting screen

Hi Friends,
My new mobile phone SPV M600 got stuck whil starting showing four lines of messages as shown below.
IPL 2.10.0001
SPL 2.10.0001
GSM 02.07.20
OS 2.10.1.22
Can any one please help me in geting my phone to today's screen.
I also attached the screen shot for reference.
did you try a hard reset ?
Ya I tried both hard as well as soft reset but same screen is stuck again and agian.Can any one please help me in this regard as I am very new to PDA family.
Ok, first things first:
Since you are new to this, are you sure you preformed a hard reset?
It is done by holding power + camera + comm manager buttons (one on the right, two on the left) and pressing with stylus in the reset hole at the same time.
A message should appear asking you to press 'send' (green phone button) to confirm reset.
If this does not help, you may have a serious problem.
Please answer the following:
Is the device fully charged?
Phone will fail to boot if the battery is too low.
Did you install any software right before this happened?
This should have been resolved by hard reset, but just in case I am asking.
Did you change the ROM, attempted CID / SIM unlock?
This could require more serious measures than I can advise on.
I did exactly the same thing which you mentioned.But even then it is stuck at the same screen.
Ya u r right I unlocked my mobile using a software from eBay.The unlock was successfull and I tried to insert T-Mobile sim, it also captured the signal and I was able to make and recieve calls then after that I wantedly switched off the phone and then tried to start it, there got the problem.
Can any one help me in this regard please.
I am having the same problem, but my phone is not sim-locked.
I've got the same problem after attempting smart1_wm6_pp8mb.exe
I'm having the same problem with my G4 QTEK S200:
Attempted to upgrade to WM6 Rom using smart1_wm6_pp8mb.exe
After reboot the phone got stuck at the QTEK Screen
Tried Hard Reset (Camera+Power+Comm+Reset) followed the steps with the same results (bricked)
I also tried re-flashing the rom back to the factory one using RUU_Prophet_220734_2207114_024721_QtekWWE_Ship and ROMUpdateUtility-NoVendorID.exe in Windows Vista with WMDC (Windows Mobile Device Center v. 6.0.6873) and the phone in boot loader mode (tri color screen) with working USB cable, with windows firewall disabled and symantec AV disabled as well, RUU keeps saying error 260 "the update utilitiy cannot connect to your pda phone..." .
Do you think I should try this process using XP instead? No matter what i try i keep getting the error 260
Any help would be greatly appreciated
Got it fixed!
it was definately a Vista issue. once i tried it in XP with ActiveSync it worked like a charm and i got my phone back up and running. also used spb backup and restored all my settings.
ipl/spl screen
i got the same problem with new rom wm6, and the 260 eror, my problem is that i have xp and the activesync does`t connect ...
... means i cant redo the original rom ????
PLEAAASEEE HELPPPP !!
Again My phone SPV M600 got stuck at IPL/SPL screen
Please Can some one advice me how to get my phone back.
I raised the same issue 7 months back after that my phone got recovered automatically and there were no issues till last month. Last month onwards it is again got the same problem and now it is permenantly stuck at that screen what ever you do.
yekanth said:
Please Can some one advice me how to get my phone back.
I raised the same issue 7 months back after that my phone got recovered automatically and there were no issues till last month. Last month onwards it is again got the same problem and now it is permenantly stuck at that screen what ever you do.
Click to expand...
Click to collapse
A rom reinstall on xp solved my problems on that one. retry a couple of times! It may not work the first time! hard reset as well...
Try an official wm5 rom just in case
good luck
Can you please gimme step by step procedure
HI Phil,
I am new to these kind of installations . CAn you please Gimme step by step procedure for ROM installation.
mine is now also stuck, after trying to install new rom. wont connect to active sync either, have i fooked it? tried hard reset etc.
thanks
(with a turned off phone, press and hold camera button then insert USB cable)
then flash provider ROM
RECOVERING FROM ERROR IN STEP 8 WM5->WM6
1. Don't panic
2. Don't panic
3. Unplug the phone
4. Reset with stylus,and keep the Camera Button pressed.
5. A 3 color screen will appear(Bootloader Screen)
6. Connect your device with your PC,and run the NVID(no vendor) WM5 rom.
7. The device will be resetted after RUU(rom update utility)finishes
8. Repeat the WM6 upgrade,from STEP 5..
Click to expand...
Click to collapse
from here http://forum.xda-developers.com/showthread.php?t=310452
hi jay
i seen your post in n00b guys one, i fixed it!!!!, thank you so much, i couldnt remember how to get it to those 3 colours.
thanks again
Colin
Hi Iam unable to get the NVID ROM
Hi,
I am unable to get the NVID ROM. The Rapidshare link that has been provided in the other thread is not working. Can some one tell where can i get the ROM.
collywog19 said:
i seen your post ...
Click to expand...
Click to collapse
no problem mate.
..and yekanth i see what u mean about the dead links. i have the files on my computer at home but i'm posting from my prophet right now, so i can't upload. Try using the "pdaviet temp" from one of the wm6 threads?
(http://rapidshare.com/files/54265407/Prophet_PV_Temp.zip)
Hi Iam able to update the Rom but no use
Hi,
To mention my phone is from orange-UK. I got the orange rom from our FTP site and did the flashing/update what ever you say.But still it is getting stuck at the same IPL/SPL screen. Iam very much worried that I will not get a proper solution for my problem.It will be very grate full if some one resolve my problem.
just seems strange...how did you fix it last time? did it just start working again? A random guess would be that the camera button got liquid spilled on it or is stuck in.
If the camera button is pressed in the phone will go to 3 colour screen every time it is turned on.
It won't do any harm if you try to press/move that button to see if u can "unstick" it, not likely I think but u never know...

WM6 Update failed

Help, my Atom Life is stuck in the upgrade screen and won't turn off or anything unless I do the procedure for HARDreset.
It then still returns to that screen it shows while upgrading.
What do I do?
HELP!
rebeltrousers said:
Help, my Atom Life is stuck in the upgrade screen and won't turn off or anything unless I do the procedure for HARDreset.
It then still returns to that screen it shows while upgrading.
What do I do?
HELP!
Click to expand...
Click to collapse
did u disconnect the USB?
try on bootload mode. remove u,r mini-SD pres rec+volume+restart now it will enter boot load mode, try again update.......
Nope, just thought that running an update designed for compatability with vista would work!!!! (WM6)
Did the whote thing again on another XP computer and it worked fine! No problems!
Thanks heaps!
rebeltrousers said:
Nope, just thought that running an update designed for compatability with vista would work!!!! (WM6)
Did the whote thing again on another XP computer and it worked fine! No problems!
Thanks heaps!
Click to expand...
Click to collapse
BTW, I did the upgrade on a XP session in a VMware workstation 6 virtual session under Vista x64 and it even worked fine.....
Yeah I did mine on a vista laptop. LUCKY!!!!
Hmmm actually it doesn't seem to let me connect to my wireless modem at home anymore. What settings do I need to change?
All I use the wifi modem for here is the internet on my PDA and laptop. It is unsecured and always shows up but I can't get anything in the browser or get a ping to work. The self diagnostic works fine too, and everything worked fine before I upgraded the ROM.
Any help?
Fixed! YAYYY!

Atom flash ROM Success, stuck at Update Utility Screen

Dear All,
My Atom flash wm5 ROM everything successfull, but when i cold reboot or normal reset, always go to Update Utility Screen. Can't go into the system.
Anybody can help me ?
Thanks in advance,
Regards,
bennyyen said:
Dear All,
My Atom flash wm5 ROM everything successfull, but when i cold reboot or normal reset, always go to Update Utility Screen. Can't go into the system.
Anybody can help me ?
Thanks in advance,
Regards,
Click to expand...
Click to collapse
Try to reflash it again, got the same problem before. Check if you can go to bootloadler and reflash.
brian_2cool4u said:
Try to reflash it again, got the same problem before. Check if you can go to bootloadler and reflash.
Click to expand...
Click to collapse
Thanks for your reply, can u guide me how to go to bootloader and reflash ?
bennyyen said:
Thanks for your reply, can u guide me how to go to bootloader and reflash ?
Click to expand...
Click to collapse
put device in boot loader mode press "camera button + reset". If boot loader is not working. just try to reflash the unit again using DSUU, but make sure your unit still have ample enough of batt.
or try other suggestions posted in here.
but for me above mentioned steps work.
Hopes this one may help you
brian_2cool4u said:
put device in boot loader mode press "camera button + reset". If boot loader is not working. just try to reflash the unit again using DSUU, but make sure your unit still have ample enough of batt.
or try other suggestions posted in here.
but for me above mentioned steps work.
Hopes this one may help you
Click to expand...
Click to collapse
Thanks brother it helped my Atom Exec also (Oh I was sweating ).
tjkhattak61 said:
Thanks brother it helped my Atom Exec also (Oh I was sweating ).
Click to expand...
Click to collapse
No problem, I was sweating and crossed my finger when that happend to my unit before. I thought i'll say goodbye to my atom.
glad to help =)
I use Chinese Version WM6 ROM to flash it, for Step 1 CE ROM update are successfull, but Step 2 Bootloader get error, can't flash.
Without touching anything ( Remove cable or reset ), i try to use English Version WM5 ROM to flash it, Step 1 CE ROM update stuck in 0%, device screen blind. Wait for 5 min, still maintain 0%. Try to reset, can see O2 welcome pic, wait for a moment can go to setup screen, everthing is ok. Go into system try other function all can work, but when i reset. It return back to Update Utility Screen, same as previous problem again, put in battery automatic go to Update Utility Screen. Can't go into system again !
Anyone can help ?
Thanks in advance !
Where did you aquire this Chinese rom, perhaps you must ask the author or you could keep reading, try the Wiki!
bennyyen said:
I use Chinese Version WM6 ROM to flash it, for Step 1 CE ROM update are successfull, but Step 2 Bootloader get error, can't flash.
Without touching anything ( Remove cable or reset ), i try to use English Version WM5 ROM to flash it, Step 1 CE ROM update stuck in 0%, device screen blind. Wait for 5 min, still maintain 0%. Try to reset, can see O2 welcome pic, wait for a moment can go to setup screen, everthing is ok. Go into system try other function all can work, but when i reset. It return back to Update Utility Screen, same as previous problem again, put in battery automatic go to Update Utility Screen. Can't go into system again !
Anyone can help ?
Thanks in advance !
Click to expand...
Click to collapse
I had the same problem, read this it might help.http://forum.xda-developers.com/showthread.php?t=358442
tjkhattak61 said:
I had the same problem, read this it might help.http://forum.xda-developers.com/showthread.php?t=358442
Click to expand...
Click to collapse
Thank you for your help, now can go into system. But no radio, want to flash in Active Sync, show me Country ID Error, into Bootloader flash, show me connection error. Would you mind to help in this also ?
Thanks in advance !
bennyyen said:
Thank you for your help, now can go into system. But no radio, want to flash in Active Sync, show me Country ID Error, into Bootloader flash, show me connection error. Would you mind to help in this also ?
Thanks in advance !
Click to expand...
Click to collapse
if there is no radio, could have been a flash problem. try to reflash it again.
try changing USB cable aswell it can be a faulty one
brian_2cool4u said:
if there is no radio, could have been a flash problem. try to reflash it again.
try changing USB cable aswell it can be a faulty one
Click to expand...
Click to collapse
Thanks brian_2cool4u, will try later...
Already test in 4 different USB cable and in different computer also. Still display Country Error in Activesync and Connection Error in Bootloader....
bennyyen said:
Already test in 4 different USB cable and in different computer also. Still display Country Error in Activesync and Connection Error in Bootloader....
Click to expand...
Click to collapse
Hmmmmm thats odd? it should have been fix, oh well better get advice from where you got the rom or do a little reading in the wiki
Already can connected and flash any ROM, but new problem come out.
Comupter stuck at Stage 5 0% among 3 hrs still maintain 0%, but my device show Burn Radio MOT 100% completed
So i try to unplug the USB cable, my computer immediatly show Connection Error. After i hard reset my device, everything OK except No Radio ( NO GSM ).
Any advise
Thanks & Regards,

Hp 6945 Stuck at Serial and Hp invent logo

Hello Everyone
I need big time help. I just bought Hp 6945 and I tried to update GSM rom from 1.02 to 1.08, while updating it says update fail and try to restart Ipaq and start again. Now My problem is Ipaq just stuck to Hp invent logo. I tried to reset and hard reset and remove battery but notthing work.
I need help
Could some please help me to How to fix this problem?
Thank you
same BS happened to me. the only way to fix it is to load the UK 6915 ROM. thats the ONLY way to fix it. AVOID this update do not try to update the radio. I bricked my phone doing this. STILL looking for a solution. Radio stack is daamged.
where Can I find Uk 6915 rom
Thank you for reply. Where can I found the UK 6915 rom. Is there any instruction to How to load rom?
Thank you
If is FIXEDDDDDDDDDD
Ok
I got it fixed, very simple solution
found it here
http://pdaphonehome.com/forums/hp-h...dowloaded-rom-update-ipaq-dead-need-help.html
Solution:
this is what I did to get this fixed.
1) Get the battery out of the iPaq, and wait for a few minutes while the "serial" image fades away slowly.
2) In the meantime, prepare your cradle, plugged into the AC charger and plugged via USB to your PC.
3) After a few minutes, with the screen of the iPaq completely gray, put the battery and battery cap back on (with our without SIM card), and put it on the cradle immediately.
4) The iPaq should start coming back to life, as if it were being hard reset. Let is stay on the welcome screen (i.e., do not tap it or anything).
5) Restart the upgrade process, it should proceed from there OK
Thank you to origianl solution provider
No network connection
Ok everything work fine, but Now I cann't connect to tmobile. It keep showing me no service.
Any Help please
Ok It is fixed again
There is another update at HP website, which is software update. After installing that everything working fine.
can anyone help? i just bricked my ipaq 6965 too. had already followed those few instructions without any success.. what do you mean by "with or without SIM card"?
After a soft reset, mine's stuck at the initial blue/white boot screen.
Hard reset doesn't work (assuming its call + hang up + power + poke reset).
Ideas?
bring back to life hw6945
i'we tried like you to upgrade radio part and a got an freezed phone
Solution for repair was flashing firmware with this program..
Download-Link #1: http://rapidshare.com/files/96527845/Ipaq_HW69XX_ENG_ROM.zip.html
download files from rapidshare posted by me ,r tested on my phone
hi i have tried to dl the rom asi having the same prob but the file cannot be downloaded. is there any other way to get from you
garyakw said:
hi i have tried to dl the rom asi having the same prob but the file cannot be downloaded. is there any other way to get from you
Click to expand...
Click to collapse
If you are stuck on a HP Invent Screen, with G.39, etc.
And you have tried to hard reset and softreset with no luck, this is what you do.
XP Instructions:
1. Download this link http://www.mediafire.com/?3ygfbx0sjdy
2. In the taskbar area in the right hand corner, right click on activesync, bare with me, I'm using Vista and have to remember this, click connections..., you need to uncheck everything click ok or apply...
3. press ctrl-alt-delete, end process wscescomm.exe, (named something like that, end the process.
4. Extract the file you downloaded if needed.
5. Connect your device to the usb port on your computer.
6. Run Uni Exit Bootloader Application. Done
Vista Instructions:
1. Download these 2 links, and extract them if necessary.
http://www.mediafire.com/?3ygfbx0sjdy
http://www.mediafire.com/?9pmjkponfsg
2. Start Device Manager, (Start-Control Panel, Class View[Far Left Corner])
3. Connect HW6900 to USB port, you should now see a Mobile Devices (Next to + sign), Double Click
4. Right-Click on the Device, Click Update Driver Software, Choose let me pick from a list, Uncheck compatible hardware box.
5. Click have disk, Browse to location where USBAS is extracted, choose the wceusbsh.inf file, Double Click.
6. You should see Microsoft USB Sync, if not and it reverts back to the already installed file, and the box rechecks itself, uncheck it, choose microsoft, and choose the latest Microsoft USB Sync to install
GOOD LUCK
in reference to
Default bring back to life hw6945
i'we tried like you to upgrade radio part and a got an freezed phone
Solution for repair was flashing firmware with this program..
Download-Link #1: http://rapidshare.com/files/96527845...G_ROM.zip.html
its a no go here...
i get error 402.... times out and no can do.... what was that about german language... maybe i just need it spelled out. which screen does the unit need to be in. there is two... monochrome serial vs usb and there is the hp logo blue and white screen frozen indefinitely... please help i love this phone...
Hi, the rapidshare file is missing!
Could you give working link or send me the file to mail, please?
ipaq dude said:
Ok
I got it fixed, very simple solution
found it here
http://pdaphonehome.com/forums/hp-h...dowloaded-rom-update-ipaq-dead-need-help.html
Solution:
this is what I did to get this fixed.
1) Get the battery out of the iPaq, and wait for a few minutes while the "serial" image fades away slowly.
2) In the meantime, prepare your cradle, plugged into the AC charger and plugged via USB to your PC.
3) After a few minutes, with the screen of the iPaq completely gray, put the battery and battery cap back on (with our without SIM card), and put it on the cradle immediately.
4) The iPaq should start coming back to life, as if it were being hard reset. Let is stay on the welcome screen (i.e., do not tap it or anything).
5) Restart the upgrade process, it should proceed from there OK
Thank you to origianl solution provider
Click to expand...
Click to collapse
Man,r u sure the above can work well???? Confusing......I did the above like u indicated,but it's not work on my device HP6915,could u make it in details how u fixed the problem of updating ur device,thanks!
Regards,
Brose
Thanks, This help get me out of freeze
Thanks for posting this link. It brought my hw 6945 back out of the freeze. Stay away from HP's site update. Bad news
johnnynomadic said:
in reference to
Default bring back to life hw6945
i'we tried like you to upgrade radio part and a got an freezed phone
Solution for repair was flashing firmware with this program..
Download-Link #1: http://rapidshare.com/files/96527845...G_ROM.zip.html
its a no go here...
Click to expand...
Click to collapse
Thanks for UNIEXITBOOTLOADER thing, it makes my 6965 rocks again! Btw, could this file be used on other pdaphone such as O2 Atom? Thx b4.
Maybe
Most Likely Yes
bmw2320 said:
Thanks for UNIEXITBOOTLOADER thing, it makes my 6965 rocks again! Btw, could this file be used on other pdaphone such as O2 Atom? Thx b4.
Click to expand...
Click to collapse
cdguider said:
Most Likely Yes
Click to expand...
Click to collapse
I don't think so,Curtis.....But as I know most of dopod device hardly be dead....

Frozen on blue 'Windows Mobile' screen

Hi,
I've been reading through these forums and am getting very lost as to what to do.
I have the Orange SPV M3100 and it won't boot into windows. On switching it on, it does the orange bit: at the bottom - "m05 s04 b06 d1.23" and 'No GSM' flashes up briefly before the freeze on 'Windows Mobile' loading screen.
On pressing 'Ok' and power button together with a soft reset, I get to the tri-colour screen and it says "HERM100", "IPL-1.01", "HERM100", "SPL-1.04", and either "USB" or "Serial" depending on whether or not it's USB'd to a PC port.
I've tried the master reset - top two buttons and a soft reset, followed by 'R' to confirm a full reset. It immediately said 'done' or something to that effect, but still freezes on 'Windows Mobile'.
All the help threads here seem to indicate that I need to have this phone running with Active Sync on the PC to transfer files to it in order to refresh the ROM but Windows [XP] can't see the phone because it's not finished booting.
Please please please can someone give me a nudge in the right direction?
Many thanks
Dave
as you said ok and power together with soft reset action brings you tri colour screen. At that stage you plug in to active sync (4.5) and ensure you have .net framework installed on your PC.
with the tricolour screen, plug PC to phone and run the exe file from one of these ship ROM http://wiki.xda-developers.com/index.php?pagename=Available Original Shipped WM6 ROM Versions
you should then be able to get an OS back to your phone. Then get this one on to your phone
http://forum.xda-developers.com/showthread.php?t=296722
after that you can flash what ever rom you like make sure you follow the dr's suggestions here. http://forum.xda-developers.com/showpost.php?p=1990320&postcount=6
other than that, http://forum.xda-developers.com/showthread.php?t=299462 this thread is the only one I had to go on with the first time I played with my hermes.
zocster said:
as you said ok and power together with soft reset action brings you tri colour screen. At that stage you plug in to active sync (4.5) and ensure you have .net framework installed on your PC.
with the tricolour screen, plug PC to phone and run the exe file from one of these ship ROM http://wiki.xda-developers.com/index.php?pagename=Available Original Shipped WM6 ROM Versions
you should then be able to get an OS back to your phone. Then get this one on to your phone
http://forum.xda-developers.com/showthread.php?t=296722
after that you can flash what ever rom you like make sure you follow the dr's suggestions here. http://forum.xda-developers.com/showpost.php?p=1990320&postcount=6
other than that, http://forum.xda-developers.com/showthread.php?t=299462 this thread is the only one I had to go on with the first time I played with my hermes.
Click to expand...
Click to collapse
Will this remove all data from the phone, like contacts, settings?
If so, is there a way retrieve them before reinstalling OS?
Thank you.
[email protected] said:
Will this remove all data from the phone, like contacts, settings?
If so, is there a way retrieve them before reinstalling OS?
Thank you.
Click to expand...
Click to collapse
Well if your phone is semi dead, you can't really retrieve any data other than the ones on the SD card.
zocster said:
Well if your phone is semi dead, you can't really retrieve any data other than the ones on the SD card.
Click to expand...
Click to collapse
What is "semi dead"?
In my case it frozen at windows mobile screen, before it gets the animated "busy" square at the center...any hope?
[email protected] said:
What is "semi dead"?
In my case it frozen at windows mobile screen, before it gets the animated "busy" square at the center...any hope?
Click to expand...
Click to collapse
Well if you can't soft reset successfully then it is semi dead, you have to re flash
zocster said:
as you said ok and power together with soft reset action brings you tri colour screen. At that stage you plug in to active sync (4.5) and ensure you have .net framework installed on your PC.
with the tricolour screen, plug PC to phone and run the exe file from one of these ship ROM http://wiki.xda-developers.com/index.php?pagename=Available Original Shipped WM6 ROM Versions
you should then be able to get an OS back to your phone. Then get this one on to your phone
#######################################
Hi there, well, I'm back after months of forgetting about this but still hoping to get it to work. Thanks for the above reply, but that method of putting software on still relies on getting activesync to communicate with the mobile phone via the usb cable - my phone doesn't. windows sees that I've connected a usb device but active sync gives up trying to talk to it... any further ideas greatly appreciated...
Best regards
Dave
Click to expand...
Click to collapse

Categories

Resources