When connecting my MDA Pro II to my laptop the connection via bluetooth gets established alright and I can surf the internet for a few minutes. But then the connection breaks down, as the phone has switched off bluetooth by itself! I cannot switch it back on, and I will have to reset the phone altogether to start anew. Does anyone have the same problem or a solution? Thanks!
Same here!!!
Turn off Pushmail and other apps
Turn off any app that might use the NET.
I got so freakin' frustrated with this before I had a bright moment
(first one ever)
Turn of activesync, pushmail etc on your device, SPB GPRS monitor, any app that tries to connect.
Your modem function just can't stand that.
Hi
Is anyone experiencing the following problem on T mobile UK or any other network? [t mobile touch plus]
Using your handset as a modem 'internet sharing' the handset will intermittently stop charging for 15 minutes, after using the connection ‘internet sharing for anything up to 30 minutes (connected to a desktop pc or laptop)
Secondly when the phone reaches 100% fully charged using the internet sharing, the handset stop charging and subsequently the phone switches to battery power and as a result you are working against the standby time, which when empty in let say just over an hour you will have to charge the phone again, before you can resume using internet sharing.
Radio version of handset is 1.58.21.24 it’s
The page results from surfing is fine on desktop and handset just the above problem and heating.
Any thoughts would be much appreciated
yes i get that isssue to on my niki on tmobile uk but its only just started doing it recently
try to soft reset it
All my devices, Qtek S100, Qtek S200, HTC Touch dual - they all stops charging in "Internet Sharing" mode.
internet sharing and charging..... the fix
does your handset stop charging then restarts after a little while using internet sharing, if so read below
a few things to check is to try internet connection on another laptop at the location where it is happening,if the fault is present then you have identified the fault is with the handset or network.
your next step is to try internet sharing at a different location from where you are experiencing the fault and see if the fault reoccurs, for me it wasn't until i decided to try internet sharing in another area that i discovered that the fault was network related, even though tmobile were adamant it wasn't (this fault is also related to cases where the handset gets very hot within a short of time whilst using hspda/gprs).
if the above test is carrried out and you identify that it's location based then speak to tmobile (but be persistant)
today my handset can sit idle or surfing for xyz and it is barely warm....
hopes it help
Hi everyone.
I always uses GPRS connection for my daily habits continuously connected.
I don’t know why suddenly sometime my msn disconnected & keep asking to retry & same goes with Opera or other Programs related to internet.
Every time I need to restart the hand held to refresh the connection sometimes happens twice a day.
No such problem with TYTN II in the past, I wonder where is the problem?
I have checked all the settings.
Hope someone can help me out.
Hello everyone
I'm noticing that too often when connected wirelessly to the x10 (line fastweb home) connection takes a few minutes or a few seconds and then falls wrapped the line ... Is there a way to solve this problem? Or there is a program that allows me to use the wi-fi on your laptop?thanks
Hi all!
I started again a new thread where i write down my findings in the MR2 release of the X2. It's originally on the Esato-forums, so i just put the link over here:
http://www.esato.com/board/viewtopic.php?topic=196737
Nice THKS.
7. When hanging up a phonecall, the phone makes three loud beeps via the rear speaker. WHY???
same here... but only if the person u talk to hangs up first. its so annoying.
Lerka said:
7. When hanging up a phonecall, the phone makes three loud beeps via the rear speaker. WHY???
same here... but only if the person u talk to hangs up first. its so annoying.
Click to expand...
Click to collapse
YEp, and having the phone on silent does not make things better either...
Fix
i used registry editor and changed the value of calldrop from p(play) to none.
Rene,
when you hear 3 tones after call finish - is bluetooth activated in this moment for your x2? For example, do you use BT connection to your X2 in your car (handsfree)? Do you think that there is some special requirements for BT headset using to generate this sound on main unit if call was finished?
when you see bad power consumption results - is wifi activated in communication manager in your X2? I think that if you activate wifi - it can be reason for huge additional current if unit can't find appropriate wifi network for some reason.
For example, I found that if I activate wifi - I always should connect unit to charger every day. Then I found that this is specific issue only for me. The specific way of my wifi using is followed - I use 2 different wifi connections to my X2 (on home - secured network through router and in office - open wifi network). I do have connection issues every morning in office and every evening in home. Even if my X2 reports that it's connected to office network - I can see in status bar in Today screen that it's trying to conect again and again - and also I can't use browser or Goggle maps because no data connection is available through wifi. After I power off/on my unit - it can really connect to office wifi network and I can use browser and receive mails e t.c. When I return to home, I see that unit still be connected to office network - but it's impossile. And again - I can't use browser or receive mails by using my X2. After I power off/on unit - it can connect to home network. I can't fix issues in office and in home just turn off/on wifi in communication manager - issue still be actual after this. So, what I do every day - I turn off/turn on my unit every morning after arrive to office and again power on/ power off unit every evening when arrive home So I should spent 2 minutes every morning and 2 minutes every evening to reboot unit. On other hands I think that this is step to avoid more serious issues after couple of days of Windows using - you know usially you can see performance degradation after 1 week of using of any WinMob device - looks like this is result of lot of memory leaks, memory corruptions inside MSFT SW.
if we are talking about unexpected password issue or issue when you can't unlock unit by LOCK icon sliding left or right after press on power on button - for me it looks like memory is corrupted in MSFT lock app. As result some password is requested even if user never activates this password for lock screen. But it's clear that in reality, unit doesn't story in memory any password to compare with entered one - otherwise after power off/on sequency unit still ask password from you. But as I see in the same situation with my X2 - after I remove/insert battery and power on unit - I never see again this issue just after unit goes to Idle.
I think that memory, which is used by MSFT Lock code, can be corrupted only in scope of the same Windows process (of cause if memory is isolated for all processes in WinMob - I hope it's true) - so only other MSFT code can corrupt this memory. Do you know about any public forum where we can ask help from MSFT to see in this issue? I never see that Aaron wrote anything about any contacts in MSFT - but I think that MSFT should be also responsible for any product if Windows logo is applyed to device with WinMob?
To reduce the probability of this issue I never use AutoLock and always lock unit by click on Lock icon in Today panel or by long press on right HW kwy (with key sign).
darkbuster5 said:
i used registry editor and changed the value of calldrop from p(play) to none.
Click to expand...
Click to collapse
IT WORKED!!!
thank youuu
wifi
Hi! I have a similar issue with the wifi that PanichUS described.
The phone sees the network, tells that it's available, but I am not able to connect to it (so I can not do internet browsing, read the emails, etc.)
This happened to me while switching from one network to another, which were in two different places (and the phone was showing the network still available of the place I have already left). But in my case rebooting the phone did not help.
This is not the only case. The same thing also happens to me after I use bluetooth. The phone is connected to the wifi network (I could do internet browsing, etc.), I use bluetooth, and after that I can no more recover the connection. Again it shows that the network is available, but I can not connect to it.
The only thing which helped by now was restarting my house router.
Is the MR2 the last release of the firmware by date? I have bought my phone recently, and for me it seems that it was updated: I have radio, and the theme with grey background (X2 Titan) was activated in the very beginning.
MR2 is last update for X2. Don't wait another update.
Try turn off Wifi in Communication manager before power off and turn on Wifi back in Communication manager after power on.
Wifi
I have discovered that in fact I don't have problem to connect when using an open network, while with the protected one is always an issue.
Reboot of the phone doesn't change anything even if before doing it I switch off wifi in the connections manager and delete all the settings. Nothing - only reset of the router what helps.
I also tried to use other software (Wifi Monster) - the same thing.
The phone is really wonderful, it really has it's spirit with all these panels and generally the interface, but the wifi issue is really annoying!
My advice - don't install Resco Photo manager on X2.
Great app but works very bad on X2.
I instaled older version Resco.Photo.Manager 7.03. This work good.
Wisbaradvance 4.05 is verry unstable,problems and problems.