I've installed the newest version of Pocket Bluetooth Tools on O2 XDA II with latest O2 ROM release. Two problems:
- the XDA II does not go into standby mode after answering a call
- bluetooth remains active instead of switching off after x minutes (the clock on the screen is white).
What am I doing wrong ?
Thanks,
Can I just bump up this question again. I'm very happy with Pocket Bluetooth Tools, accept for the powerdrain caused by bluetooth being on. PBT is supposed to switch is off automatically after a minute, but I find, even when it goes all the way around and goes completely white, bluetooth does not switch off.
Has anyone else found a solution to this problem? Im using the latest rom from O2 (1.66 I think).
Regards
Surur
I just installed the BT tools few days ago.
Didn't notice about the phone does not go to standby after answer the call as it has been doing it since new even before I install the BT tool.
I found there are 2 ways to get the timmer to work probably. 1) push the button on the headset after the white stop at sbout 5 min position 2) make the headset out of range.
At first, I thought I am doing something is not right, but now I know I am not alone. Hope someone can find a solution since it is useless if I have to pushh the botton to turn off the BT after the 55 seconds goes by. If I forget to do so and if I accidentally hit the button on the headset 2 or 3 times, it will dial the last number.
Also, I can't get the battry icon thing to work. Anyone know how to use it?
I am also using 1.6 rom.
Quote this FAQ from myxda.com :
Q. Is it possible to activate the loudspeaker on my xda before choosing a telephone number? Is it possible to permanently turn the loudspeaker on loud, so i do not have to press the green button?
A. There is a way for doing this. The only disadvantage: after a soft-reset this setting is not activated anymore and must be readjusted. Dial any number, for example the Voicemail Box, so that nobody is disturbed by a phone call. Then disconnect and tip onto the signal symbol in the title bar. Tip onto the disconnect telephone button and then immediately press the green button (accept telephone call) keeping it pressed until the note appears: The loudspeaker is activated. The telephone then disconnects, without establishing a connection. The information that the loudspeaker is activated remains. The next step is turning on the telephone. The loudspeaker is turned on instantly with each dialled number. However, you can always turn the loudspeaker on or off by pressing the green button a little longer BEFORE dialling.
I've tried it and there is no response, even I can not get first step (Tip on the disconnect button ). May be this FAQ is only for XDA I ...
Has anybody tried it on an XDA II ?
Has anybody a way to permanently activate loudspeaker on XDA II ?
Yes, I've tried it, it works.
But sometimes could be difficult to activate due to some lag or slow response time for taps ... Once activated, the screen will look like this:
Can yo please explain it step by step ?
I've tried a lot of times, withou results. Thanks
ok, i found this easier:
- Turn on flight mode.
- Press green button for a few seconds until it says "Speakerphone is on". (Don't worry, as you're on flight mode, no call is made)
- Now, turn off flight mode to use the phone and have the speakerphone always on.
Enjoy.
No way !!
Turn On fligth mode.
--Press green Button while in TODAY opens Phone Screen
---Press green button while in PHONE screen shows Buuble "The phone is currently off. Dou you want to turn Wireless on?
I have ROM 1.60.00 WWE
-- Radio Version 1.10.00
You'll have to PRESS DOWN AND HOLD the green button for about 2 seconds. Not just one click.
Of course I did it
Have you been able to activate speakerphone during a call before?
The procedure is the same, press and hold down the Green button should activate, except that this is done when flightmode is on.
It's strange why your unit doesn't behave the same? Try hold down longer perhaps..
@chriswo
sorry for OT, but PLEEEEASSSE let me know the name of that software you're using for the today screen. i've been desperately looking for something like this for ages now.
thanks
regards ize|man
if you mean
chriswo's screenshot
then do you mean the signal strength
or ?
if you're talking about the launcher, it's called cLaunch, it's free.
Yes I can activate it during a call, and as I like it (it works 'sufficient' for me as a hands free for the car) is because I wanted to have it always activated.
May be there is some installed software. Will try to uninstall what is not essential. Can you post your rom & radio versions ?
boyz boyz you're fast as lightning
i just updated the screenshot. pls reload this page.
and YES it's cLaunch i just googled and it seems to be what i need (BIG buttons on the today screen)
thanks a lot
regards ize|man
Alrught, if you find it difficult to activate Speakerphone while on flight mode. try this:
On PHONE display, turn on flight mode and immediately PRESS AND HOLD DOWN the green button. Don't let it go completely on flight mode, so you got to do it while the radio was shutting down.
try that and let us know.
OK, this one WORKED without problem.
Now I have a 'perfect' and 'cheap' handsfree for my car.
THANK YOU very much !!!
Chriswo?
Where did you get that signalstrenght today plug in from ? looks really good
That's HudsonMobile PhoneDashboard.
Anyone notice if you cancel the speakerphone, then enable your bluetooth headset and make a call, the headset stays connected even after you end the call?
I don't know if this really is an advantage or not, I'll see how much more the battery drains if any.
Also, I notice that after activating the speakerphone "always-on", my ringetone gets almost silent. :?
Is somebody now how to do speakerphone from XDA....I think its need only software update....
If know something about subj please email me.
Press the green phone button and hold for 3 seconds during a call.
The speakerphone turns on.
Repeat process to turn it off.
I have htc wizard with wm6 by faria. Yesterday I bought bt8010 and it all works good, but i realised that i don't have speed dial. I searched forum and install "Voice_TRI.cab" but it didn't work with the button on headset. So i've tried next "CVSD_for_WM6_v1.2_build_61226_1.cab" and this work very good. But after reset i have half icon of connections, and don't see volume and clock icon, but they are there, becouse when i click there i see menu with options to it. Do anyone know how to repair it ? i've tried deleting and installing next time but it didn't work out my problem...
wacki4 said:
I have htc wizard with wm6 by faria. Yesterday I bought bt8010 and it all works good, but i realised that i don't have speed dial. I searched forum and install "Voice_TRI.cab" but it didn't work with the button on headset. So i've tried next "CVSD_for_WM6_v1.2_build_61226_1.cab" and this work very good. But after reset i have half icon of connections, and don't see volume and clock icon, but they are there, becouse when i click there i see menu with options to it. Do anyone know how to repair it ? i've tried deleting and installing next time but it didn't work out my problem...
Click to expand...
Click to collapse
I´ve the same problem with my htc hermes (o2 trion).
I´ve installed LVSW(2007/04/08) RUU_Hermes_WWE_3.24.0.4
Anyone an idea?
My Diamond is about to go in the bin!!!
If anyone knows how to edit the registry to "switch off" the volume keys on the Diamond then please, please, please help me.
The volume screen is permanently flashing on my screen, and seems to be stuck on the up button which means I can't use the phone. it's not a hardware issue as the buttons aren't stuck or won't work, it's from a bad flash (according to HTC!) - i've tried stock roms/MTTY etc but the problem still persists from one rom to another.
Any registry experts willing to help