Database Users

Turn off the phone part

Hi,
I noticed that the Qtek 2020 doest not turn off the phone when I press and hold the red phone button.
Is that normal?? It worked fine with my XDA ( Wallaby).
regards,
Silver

When you say "turn off the phone" do you mean turn off the radio - so the device will not make or take calls?
If so, that is done by tapping the signal strength meter on the top bar and then tapping "Turn on flight mode". Flight mode gets its name from the necessity to turn off the telephone on an airplane in flight, but continue to use the PDA.
IF not this, please explain more.

Turning off the radio
Hi,
you are right I meant the radio.
With this XDA ( Wallaby) the radio can be swiched off with pressing the red phone button for 5 seconds.
This is discribed in the qtek 2020 (Himalaya) Manual as well.
But it does not work this way for me....
I wondered If you can try it with your XDA2?
Let me know.
Thanks,
regards,
Silver

Holding down the red button on my imate (and all of its cousins) disconnects the current GPRS session, it does not turn off the radio.

Yeah holding down the hang up button just disconnects GPRS on the XDA II and doesn't turn off the phone (radio).
I prefer having to switch the phone off through the signal strength box because with my XDA it used to turn the phone off in my pocket so i'd miss calls.

Thanks a lot guys. So possible misunderstood the manual then.
Thanks again.
regards
Silver

let me add that using the flight mode with XDA II is recommended in real flights as it turns off BT and IR as well ... which can intefere with the air navigation systems if left on

Hi,
Is there anybody that can write a little script with a button that could do that?
regards,
Silver

you can try PocketZenPhone. it has an option in its profiles for turning the radio off.

Thanks boybi,
A little script that playces a phone icon in the comand bar that shuts or turns the phone on would be very useful.
Can somebody do this??
regards,
Silver

Silversurfer said:
Thanks boybi,
A little script that playces a phone icon in the comand bar that shuts or turns the phone on would be very useful.
Can somebody do this??
regards,
Silver
Click to expand...
Click to collapse
HTC did that.

And it works VERY WELL thank you!

Hi Satria,
This is great, and exactly what I was looking for.
Thanks a lot.
regards,
Detlef

Key press (by mistake) on the case

When my device P3600 received call or sms, the device is powered up, and then all the keys are active. If the device in case some key can be press (by mistake) and activate a program on this situation.
Does any one have a solution for that?

Use the Device Lock Feature in your Today Screen.

I do not like to add one more line to the dotay screen
can I use it without add it to the dotay screen?

If you don't want an additional line on the today screen then the other option is to set the device to request a password after only one minute of inactivity (under "Settings", "Personal", "Lock").

anonimo said:
If you don't want an additional line on the today screen then the other option is to set the device to request a password after only one minute of inactivity (under "Settings", "Personal", "Lock").
Click to expand...
Click to collapse
10x, but this is not help, the lock is form power up the the device, and the device is automitly powered up when received call or sms

I use a program called "device lock" that can be mapped to one of the buttons, I use button one when you hold for a few seconds. The app locks the phone and turns off the screen, so when you recieve a call or sms the screen will turn back on but the phone will still be locked.
Have a search on the forums here for it, that where i got it from.
Cheers

iMike said:
I use a program called "device lock" that can be mapped to one of the buttons, I use button one when you hold for a few seconds. The app locks the phone and turns off the screen, so when you recieve a call or sms the screen will turn back on but the phone will still be locked.
Have a search on the forums here for it, that where i got it from.
Cheers
Click to expand...
Click to collapse
in this case you can not aswers a call, when received one - because when the device is lock there is no quick way to answer that call.
or I miss someting here.

Carmi said:
in this case you can not aswers a call, when received one - because when the device is lock there is no quick way to answer that call.
or I miss someting here.
Click to expand...
Click to collapse
Yes you can answer a call, the device lock only lets you use the power, answer, and hangup buttons. When the call is finished it is still locked, unless you unlock it.
I use this one. http://www.mr2-power.com/downloads/DeviceLock.CAB

10x, GREAT, this will do the job

it is work fine - 10x

Carmi said:
10x, but this is not help, the lock is form power up the the device, and the device is automitly powered up when received call or sms
Click to expand...
Click to collapse
I am glad you found a way to solve your problem but I don't understand why my suggestion should not work. If you set your device to request a pin after one minute of inactivity if you receive a message the keys will still be blocked until you enter your pin. (I am talking about device PIN not SIM PIN).
And if you receive a call the answer button works even without entering a PIN.

anonimo said:
I am glad you found a way to solve your problem but I don't understand why my suggestion should not work. If you set your device to request a pin after one minute of inactivity if you receive a message the keys will still be blocked until you enter your pin. (I am talking about device PIN not SIM PIN).
And if you receive a call the answer button works even without entering a PIN.
Click to expand...
Click to collapse
Your solution works too, the only thing is sometimes (for example) I'm sitting on the couch using my phone for email or surfing and watching a TV program. I stop to watch something interesting for 3 minutes and my phone has locked itself with the pin lock. I have to enter the code each time this happens. It can get annoying. If I use devicelock, I lock the keys when I need to, obviously when I'm at home and my phone is on the coffee table, it doesn't need to be locked. I set my device pin lock at 2 hours, that should give the phone enough time to lock itself if I loose it...hopefully.

yeah... but when you loose your phone the device lock doesn´t matter. only reinstall a Rom and your phone can be used.

dersvenni said:
yeah... but when you loose your phone the device lock doesn´t matter. only reinstall a Rom and your phone can be used.
Click to expand...
Click to collapse
Yes, very true, but at least they won't be able to see all my contacts, appointments, notes etc. That being said, I always use FlexWallet to encrypt all sensitive information which is synchronized to my laptop.

touch screen and buttons can be locked during a call?
I followed up this thread and found it very interesting. But it does't focus all the problem:
when call's come in, your solutions are ok.
But when I want to make a call, I found there is a nasty *****, clicking to call waiting or to head speaker on, opening a note or calling my voice box etc. etc.
Then I found that it was my ear or my fingers, clicking on the touch screen or my fingers clicking hardbuttons.
I think tat during a call on the normal speaker the only buttons to be active should be "hang on" and "loud speaker on". With loudspeaker or BT on, or call terminated,s screen and buttons should come back to full function.
Anybody knows a solution to this?
Regards, and keep on, its a great forum. i love it.

iMike said:
I use a program called "device lock" that can be mapped to one of the buttons, I use button one when you hold for a few seconds. The app locks the phone and turns off the screen, so when you recieve a call or sms the screen will turn back on but the phone will still be locked.
Have a search on the forums here for it, that where i got it from.
Cheers
Click to expand...
Click to collapse
Hmm this is just "device lock" that we can see in HTCplugin. In my case it does not turn off the screen. It just locks my device. Is everyone has "turn off the sreen" functionality?

> Karl der Käfer wrote:
>
> touch screen and buttons can be locked during a call?
I lastly tried the on-off button to block screen during outgoing calls.
I never did this before because I thought it would cancel the active call, but it doesn't.
Ok, I see it's more or less doing what I want. But it's very unconfortable. When I hit it bad, or don't hit it at all, or forget to press it?
Isn't there a posibility to have the screnn sensibility off, only sensibility, until the call is either ended, passed to outer speaker, headset or BT? or perhaps simply until I give it free manually?
It would improve safe usage of that phone remarkably, I think.
If not :-( , well, I allways can press the button ;-)
curious for what solutions you'll find on your problems with incoming calls. Perhaps that will give me an Idea.
Chears

I've complained about this on just about every major forum I have found. Hopefully, someone will eventually write an app to allow personalized device locking. I would set my trinity to not wake for ANYTHING and have ONLY the power button active. I would prefer to get audible alerts (or vibrate) to incoming calls, alarms and messages. Pressing power would be the only way to turn the device on. PIN features only annoy me. This would be very useful anytime I am not willing to immediately respond to a notification - driving, having dinner, in a meeting, etc. It could significantly improve battery life. I store mine in my pocket and accidental button press is a problem as well.

Screen go off on phone call

Hi, everyone. My Tytn when is on a phone call, switch off the screen. I can't find anything like this in the forun (perhaps I don't look for on the right way).
I not find how to disconnect it on the configuaration of my Tytn. Does anybody knows how to get the screen on during a phone call.
The problem is when I'm driving, and on a phone call, lose the screen and my navigator instructions. It's is a problem, cause, I must to switch on the PDA and reconnect the navigator. (the people alwais call on the worst moment , I don't know why?)
Thanks to all.

Start>Settings>System>backlight>Battery Power, then take the tick off the selection "Turn off backlight if device is not used". Do the same under the external power tab.
At the bottom of the screen you should see a MENU option. Click on the Advanced tab then take the tick off the option "Turn off device if not used for ...."
This lot should solve your problem. The downside is you might then start to use more battery power as the device leaves itself in an always on position.
VCheers
WB

wacky.banana has offered some good advice. But IF your problem happens ONLY when a phone call comes in, then I think you might have phoneAlarm installed and configured to do this. pA includes this feature in order to let folks listen and speak, with the phone against their ear, and not fear starting up myriad applications as their ear touches the pressure-sensitive screen.
Just an idea.
-pvs

just press the button
just press the standby button, or any button to turn the screen back on,
id rather have the option to turn the screen back on, rather than having it on all the time especially if i am out and about, and as we all know, battery power on the tytn is a precious commodity :_)

Can not use speaker for phone

Hi,
I am using O2 Atom with WM5. The strange thing is Phone App does not allow to use speaker. Is there any setting I need to do? I saw one option from the menu "Turn Hands-free on" but it's disabled.
Thanks,

hi
yes quite simply really keep the green glowing phone button pressed down while in conversation utill the speaker phone comes on,to cut it long press the same button,yes I know the turn speaker on button option does not work dont know why!!
cheers

Screen Lock issue with HD2

After i hang up on a call (when the phone is in sleep mode and the screen is locked) the screen unlocks. this is quite contrary to what is mentioned in the phone manual chapter 1 page 45. this becomes an issue since i use a bluetooth headset and the phone remains in its sleeve/case and after every call, a whole bunch of applications will launch since the case is in contact with the screen. have i overlooked some settings or are there other owners who have faced this issue?
ideas and suggestions welcomed

did you check it out if any of the hardware buttons being pressed against the case hence wakening up the phone.?

i had it to only closed al my apps in taskm and it stoped flickering

My HD2 is also behaving in the same way even in controlled test conditions - the phone unlocks when a call comes in (I'm presented with slide to accept or reject call) The phone unlocks during the call, but fails to lock again on disconnect (either by pressing "end call" or hang up via bluetooth).
Can anyone verify this? Is it interacting with something I installed?

I believe I found a (complicated) workaround.
What I want: leave HD2 inside pocket, answer calls with bluetooth headset, hang up and phone will go back to lock.
Problem: After I hang up using bluetooth or press the big red "End Call" button or the other party hangs up, the phone stays unlocked! It stays powered on and all kinds of buttons gets clicked.
Practically all lock sw uses their own lock screen (which I don't want to install). CSDevCtrl does not trigger by phone. TouchLockPro uses its own transparent lock screen but can respond to phone events. Using the !SUSPEND for TAPI\Ended under settings does not seem to work when the screen dims about 50 secs into the call.
Solution: Use TouchLockPro together with LockAndOff. Get TAPI\Ended to run LockAndOff will turn phone off, whether by bluetooth, big red "End Call" button, or the other party hangs up.
BTW: I think there is some confusion on whether the phone locks when you
1. press the big red "End Call" button, or
2. the hard "End call" button
in the forums.

I noticed that HD2 have a light sensor next to the top ear speaker.
During a call, if the phone is put near the ear and cover the light sensor , the screen become non-active which is good.
If anyone can come up with a lock sceen using this light sensor , then the problem with random launch of program when phone inside pocket will be solved.
This lock screen should only activated right after an end of call, beacuse , sometime you may want to use the phone in a dark place.

linivan said:
I noticed that HD2 have a light sensor next to the top ear speaker.
During a call, if the phone is put near the ear and cover the light sensor , the screen become non-active which is good.
If anyone can come up with a lock sceen using this light sensor , then the problem with random launch of program when phone inside pocket will be solved.
This lock screen should only activated right after an end of call, beacuse , sometime you may want to use the phone in a dark place.
Click to expand...
Click to collapse
It's the proximity sensor that turns the screen on and off during a call, not the light sensor. How else would it work in the dark? (which it does)

johncmolyneux said:
It's the proximity sensor that turns the screen on and off during a call, not the light sensor. How else would it work in the dark? (which it does)
Click to expand...
Click to collapse
My proximity sensor does not work, when I am getting a call my screen turn off and when I am taking the phone out from my face it turn on only when I am out side at the sun!! the screen stay off when I am inside room. I tested it with flsh light and it is working also.

I have a T-Mobile US version of the HD2. I am having the same problem when using the bluetooth system in my car. After answering or making a call the phone stay unlocked. And then starts making random calls while I am driving!!!!
There has got to be an easy fix for this!!!

Buy pocketshield, problem solved.

i have this unlock problem with 1.48 rom and i solve it by pressing start button and lock. after that everything works fine unless i change theme in settings. then just repeat first step.

Solved
Same trouble with me until I use the following software. I tried it and it's almost perfect. unzip it and just copy to your HD2, run CallerLoc.exe and click Yes, you'll find:when you hang up, or he/she hang up a call, or a call is established, the screen will turn off.
Why say 'almost perfect', the software is in chinese, but the filename is in english. and it's a call location software but with the function we need.
To stop or before you delete the software, run Callerloc.exe and click Yes again.
Hope this will help you. Sorry I don't find a English version of this software. I esure and I'm using this software perfectlly with my Leo.

theciscokid said:
Buy pocketshield, problem solved.
Click to expand...
Click to collapse
Same for me

Greetings.
I understand this is quite an old thread I'm digging up but I need a little help as well and I didn't want to start a new topic just for that.
I've this silly problem, appeared right out of the blue:
You all know the standard manila behavior, when the phone is idle, the screen first dims and after some more time, depending on your preferences, the screen locks. It also locks if you press the power off button. This all was happening to me till this morning.
I added an event in the calendar (the only change I made today) and after that, my phone dims and then goes in sleep mode after the designated period of time, but DOESN'T lock!!! It doesn't even lock when I press the power off button. I can still lock it by pressing Start and then lock or by press and hold the power button and choose the lock phone option. So one would say that it's still operational, so why bother about it, but I kinda liked the standard function and I have to freaking idea why it changed!!!
I'd be most appreciative if you could offer some help with that.
Oh, I forgot to mention. Soft reset didn't solve the problem. Erasing the calendar event didn't either.
My phone runs the factory ROM (1.66.482.1 ELL), I haven't changed anything other than user settings (yeah, I'm a noob... )
Thanks in advance!
Nasos

Pocketshield could be the end of your problems. You can try it for 10 days and see how it goes...

But why do I need to buy third party software in order to revert my phone to it's original operation?
No, this is not the answer I am looking for. I was wondering if you know of any kind of settings that might have changed by accident and caused this undesired behavior.
Thanks.

The best to return to normal operation would be a hard reset. Or you can spend a while trying.
You can try
HKLM\Software\Microsoft\Shell\Lockscreen\Enable=1
HKLM\Software\Microsoft\Shell\Lockscreen\Active=1

Thank you very much. I opted for the hard reset option... I hope it stays ok this time!

My HD2 also had some strange unlocking and unwanted calling.
I noticed it appeared when using the android style lockscreen.
When I changed back to the original one, problem solved

i had this too. the andriod lockscreen seems to be a bit buggy last time i used it, i accidentially called 7 random numbers