Database Users

FallBack Qtek ROM Upgrade....

Hello all,
I have upgraded my Qtek 1010 form its original Rom lvl to T-Mobile 4.00.21 Eng,
I had couple of problems with this Upgrade, so I decided to fallback the changes but whenever I run PROGRAMM A I got the following msg in the DOS session:
ERROR: GetConnectionType - An existing connection was forcibly closed by the remote host.
error getting connectiontype
I don't know where the problem is!!!!
Please help me to move on.
Thanks in advanced.
Best regards,
John. :roll:

Hi ..
if you took the time to read through this forum before upgrading you should have found that by upgrading to either 4.00.16 or 4.00.21 you have no way to change the ROM except using the SD card method.

Thank you for fast response,
Could you please point me to the right document/Procedure to prepair the ROM on SD and boot from there.
...
John

I managed to download the ROM to SD Hardrest the device, but which ACTION key should I press to accepts the Load from SD?
I've pressed "Power button" and got 4 colors screen "Whit, Red, Green, and Blue" with the title WALLABY Bootloader V5.15 and at the bottom GSM OK......
Guys What should I do? Wait.... Reset.....
I've been waitting more than 5 mints and nothing chane!!!!!!!
Please help.
Thanks to you all. :shock:

The "Action" key is activated by pressing the middle of the 4-way joypad switch.

Ohhhhhhh,
No I'm Back to xda-developers.com ROM Image......
Thank you all for your support.
I'm so glade to join such a forum.
Again Thank you all.
:lol:

T-mobile Mda stuck on boot screen

I have a cid and sim unlocked T-mobile mda running Wm5. Problem is now when I boot up the device it hangs @ the T-mobile boot screen. I have
ipl 2.26
spl 2.26
Gsm 02.25.11
os 2.26.10.2
Any help plz guys
EDIT... FIXED THE PROBLEM Found this in and it worked...
Ok here´s how I done it.
First, I must explain what was the problem.
After update the firmware (not actually upgrade, I had the phone full of trash, so I decided to reflash same firmware v2.18 PTG), the Qtek 9100 / HTC Wizard freezed at 2nd splash screen (the one that shows OS versions IPL version, ect). Tried many different versions, upgraded to 2.24, 2.25, downgraded even to 1.6.7.3, but always same problem, freezed on second splash screen. I read many topics on xda-dev, and seen some people with same problem. Apparently there was 2 solutions. 1- send phone back to warranty. 2- write backup ROM from SD in bootloader.
Passed more then 15 hours asking for this SD backup everywhere, and COULDN´T find any help. Apparently no one had this "SD dump ROM Backup".
So here´s how I solved my problem
1- I tought that a SD backup was needed, and yes it is. But u can use your own phone and your own SD to do it.
2- Get a clean SD card (in qtek 9100 / Htc Wizard case is MiniSD) with 128MB (some people say 64MB, but I personally used a 128MB, maybe a 64MB is enough)
3- Kill (task manager) wescomm.exe (this is related with activesync installed on your PC). Insert the blank SD card on the phone.
4- Get your phone in bootloader mode. Like this : Phone powered off, press Camera button + Power On, will enter in bootloader mode (RGB screen).
5- Now connect your USB cable to your phone. And start MTTY_updateROM.exe (http://wiki.xda-developers.com/uploads/romupdate.rar). After open, on Port selection, choose \\.\WCEUSBSH001 and press OK. A window will open with a blank sheet.
6- Type "r2sd all" and hit enter... wait to the end (at end shows "cmd>"). On your phone screen u can follow backup progress... small bar will appear down the RGB screen.
7- Power off the phone (or remove battery), enter bootloader mode (camera button + power on) and this time RGB won´t appear right away. Will ask if u want to "download SD image", press voice dial button to agree, and writting will begin. Wait to the end. Power off and power on normally. Now your phone should be working ok. Not even needed to reflash the phone after this.
Thanks to all and hope this helps more people with this problem

5- Now connect your USB cable to your phone. And start MTTY_updateROM.exe (http://wiki.xda-developers.com/uploads/romupdate.rar). After open, on Port selection, choose \\.\WCEUSBSH001 and press OK. A window will open with a blank sheet.
The only Port Selections available are:
COM1
COM2
COM3
COM4
COM5
What am I doing wrong?

i got the same problem too
only com1 and com2 r there
pleace help me

Yes please someone help!
I want to try this, too, but my mtty tool only shows some com-ports and not WCEUSBSH001 ! what's wrong?
Does this work with mini sd cards bigger than 128 mb, too? is there a limit?

ok, I have the right port in mtty tool now, but...
when I enter "r2sd all" and press enter it says this:
r2sd all
***** user area size = 0x77F00000 Bytes
R2SDBackup() - Download type = 5
usTotalBlock = 1 sizeof(SDCARD_SIGNATRUE_TABLE)=512
You didn't get the proper security level to download a specific image
Cmd>
what can I do?
any help is greatly appreciated!

Upgrade ROM without ActiveSync!

hi bro
My Herald have a big problem. it's freeze on the HTC spash screen and can't load the ROM. I've made a hard rest, it's done but the problem ist still present.
I've download the Windows Mobile 6 RUU on the HTC official site but it's impossible to do the rest because ActiveSync is not connected with my phone. How can i resolve my problem without ActiveSync?

see this post 6
this method work!
http://forum.xda-developers.com/showthread.php?t=340618

I've done all said in the forum you have indicate but nothing....
I fear that my device is not out!

WaveMaster1406 said:
hi bro
My Herald have a big problem. it's freeze on the HTC spash screen and can't load the ROM. I've made a hard rest, it's done but the problem ist still present.
I've download the Windows Mobile 6 RUU on the HTC official site but it's impossible to do the rest because ActiveSync is not connected with my phone. How can i resolve my problem without ActiveSync?
Click to expand...
Click to collapse
Have you placed the phone into bootloader mode before using the RUU? (Holding the camera down and pressiing the soft reset button?)

Activesyn won't recognize the phone if connected during bootloader ... but if the phone says "USB" on the bottom left, you can run the RUU and it will work.

My device display "USB" in bootloader mode when i connect it to my PC.
But the problem is that the pc can't detect a new device connected...
When i try to flash by the SD card my herald can't detect the card!
I'm affraid! Please HELP ME!!!

why you d´ont write more?
isp XXXXXXXXXX
spl XXXXXXXXXX
card formatted at FAT 32?
camera + comm + reset ?
and was see you
"card not recognized?"
i am not a profi, but if one one this read, can you help
i find this in herald forum from here, try it again, and again....
and answer.
Ciao

why you d´ont write more?
isp XXXXXXXXXX
spl XXXXXXXXXX
card formatted at FAT 32?
camera + comm + reset ?
and was see you
"card not recognized?"
i am not a profi, but if one one this read, can you help
i find this in herald forum from here, try it again, and again....
and answer.
Ciao
IPL 1.08.0001
SPL 1.08.0001
It's normal that i get same informations about IPL and SPL?
I've done the procedure to enter in bootloader mode
But my computer don't detect it and my device display "USB" in the white area
of bootloader screen (this is normal)
But i don't know why it can't read my card with HERAIMG.NBH file inside!!!
The version of my bootloader is not displayed. Is it normal?
Per aps my bootloader get to be flashed, but how can i do it if it's the source of my problem?
PLEASE YOU ARE MY LAST SOLUTION!

about ipl 1.08xxxx and spl 1.08 xxxxx (very bad problem)
http://forum.xda-developers.com/showthread.php?t=343760&page=2
1 you have original Ruu.,.,......ship.exe
try it again when you are in bootloader mode, and reply. goes or not?
2 you have your original ruu..........ship.exe
whit winrar extrat all, and you have to rename the ruusigned file (60MB or more MB not the file with 1 MB!, to HERAIMG.nbh.
if dont work i some not can help you i m sorry.
my device work after many problem again but i have no WLAN and i have not isp 1.08xxxxxxxxxx
i wish you can write very good new!

show in your computer
if you are in bootloader mode wiht herald
if you have a networkcard not active! reactive this now
i had wm5 and his sync automatic
but after data crash on herald with wm6 does not sync again,
i search in my computer and a have see that 1 windows mobile device card does not was connect and i have reconnect this. and momentanly works again good with wm5, wm6, touch flo
show, you have no other way
ciao

Another Can't-Flash-Rom post. Please help.

I upgraded the ROM to 6.1 awhile back.
Now, I would like to upgrade to the PDAVIET ROM WM6.5 (Core 21502) by TranMinhMan.
However, I'm running into this problem:
I get stuck with the screen showing 4 colors: Red, green, blue. & White.
The red screen saying:
POLA100 MFG
SPL-2.20.OliNex
CPLD-2
Green: nothing
Blue: nothing
White: USB.
& the RUU shows Error 260.
ERROR [260] : CONNECTION
This error occurs when there is an “open port error” before upgrading the CE ROM image.
Solution: You can reset the device and run RUU again. If you still encounter an “OPEN PORT ERROR” again, reset your computer and try again.
I hard reset the phone, reinstalled HardSPL, pretty much did everything but cant get pass that screen.
Thanks for any help.
D

Try this...
Replace only the ROMUpdateUtility file from some other previous flashed ROM (which you know it worked) over the existing one in the PDA Viet 6.5 ROM file folder. It should be the same size in all ROM's files (1416k or something) and then try again.

dizzyvampire said:
Replace only the ROMUpdateUtility file from some other previous flashed ROM (which you know it worked) over the existing one in the PDA Viet 6.5 ROM file folder. It should be the same size in all ROM's files (1416k or something) and then try again.
Click to expand...
Click to collapse
Hi dizzyvampire,
My previous ROM update (6.1) was directly downloaded from HTC 's website, so it's: _HTC Touch Cruise_RUU_Polaris_HTC_WWE_3.13.405.0_radio_sign_25.85.30.07_1.59.42.15_Ship.exe
How do I seperate that 1 ROMUpdateUtility?
thanks,
D

does it show in the right up corner RUUNBH ?
if so visit:
http://forum.xda-developers.com/showthread.php?t=382447
also read:
http://forum.xda-developers.com/showthread.php?t=512071
i had the same problem kind of this might help.
I hope so.

dsymbol said:
Hi dizzyvampire,
My previous ROM update (6.1) was directly downloaded from HTC 's website, so it's: _HTC Touch Cruise_RUU_Polaris_HTC_WWE_3.13.405.0_radio_sign_25.85.30.07_1.59.42.15_Ship.exe
How do I seperate that 1 ROMUpdateUtility?
thanks,
D
Click to expand...
Click to collapse
well...you have to read first the "How to have ..." post at the beginning of this Polaris Upgrading.You have to "Hard spl" your device first etc, etc ...tought you've done that already after you'll do that it will work much better if you stuck somewhere just post here...

[Q] Vanilla upgrade failed, USB out on TYTN

Hello,
I've tried to reload my TYTN with Vanilla Rom to resolve the 'no gsm' message on it. During the flash, Usb link is lost and now when I turn on the PDA, I've just the screen above.
Now, the USB port don't work, when I connect the PDA on PC it don't see it. Maybe it is possible to restore it with SD card but how?
Thank you for your help an sorry for my bad english (french...)

Hello,
Nobody coud help me?
Or is that mean than my TYTN is definitely out?
Thanks.

get a storage card less than 2GB, format it and in your PC rename the Signed.nbh file to HERMIMG.nbh. Insert the storage card and put the device in bootloader mode it will start the flash from the sd card

Thanks a lot +QuePPC.
I 've execute your instructions, it better but after bootloader, I have wrote in blue on white screen 'loading', few seconds after 'checking' and finally '00028002' 'not allow'.
After that, the pda return on 4 colored blocs, on the upper (red) there is writting :
in white : HERM200 IPL-1.00
in yellow : HERM200 SPL-1.04
On the lower bloc (white) 'Serial'
When I reset the pda, I have these instructions at the bottom of the screen :
M 05
B 04 No GSM
B 05 D 3.22.0.0
Maybe this malfunction is due to a wrong rom but how identifie the right rom and where found it ?
Maybe it's due to the hardspl not installed but how install it wihout usb connection. ActiveSync don't connect the pda.
Thanks a lot for your help, have a good day.

Hello,
After researchs on the forum, to restore my tytn, first I must reinstall the original rom but ... i haven't it in archiv.
Is somebody could tell me where find the french rom htc tytn wm5 (3-22-0-0 I think)
Thanks a lot.

Sisise said:
Hello,
After researchs on the forum, to restore my tytn, first I must reinstall the original rom but ... i haven't it in archiv.
Is somebody could tell me where find the french rom htc tytn wm5 (3-22-0-0 I think)
Thanks a lot.
Click to expand...
Click to collapse
you can start searching at .... http://shipped-roms.com/shipped/Kai....0_radio_sign_25.83.40.02_1.65.17.56_Ship.exe