Database Users

Magician: turn on only in bootloader, can't be flashed

Please, help me in the following situation
I bought Qtek s100 It turns on only in bootloader mode. What was before I don't know.
Now I try to reflash it via PC. I unpacked rom 1.12 from imate and put there file MaUpgradeUt_noID.exe and then ran it. The utility can't see the device information (it is normal) but it can't see the informatin about the rom I'd like to flash. I click @[email protected] but it says it gather information about the device and nothing happened.
I tried to run again about 20 times, but nothing helped.
I tried to flash it via card using rom-image but there is no invitation to reflash though I flashed via card more than 20 times other htc devices and then everything was ok.
I ran mtty 1.42 and gave command d2s, but it said unknown command. Then I gave d2s command then the device turned off.
I have qtek s110 with broken display. Is it possible to change rom-memory?
Is it possible to get service_manual for magician?
Thanks

First of all, did you back up your current ROM to SD before Flashing new ROM.
1. Yes. It's VERY GOOD. Disconnect your device from PC. You need to insert SD with your ROM to the device and Turn On. Press Power or Cancel button (i didn't realy remeber try all). After that device will flash ROM form SD.
2. No. It's VERY BAD. You need to know start address form what device should start after Reset. Sory here i did not know what it is.

Ñïàñèáî çà ïîìîùü!
Ñóòü â òîì, ÷òî àïïàðàò ñ êîìïà øèòüñÿ íàïðî÷ü îòêàçûâàëñÿ. Ïîïðîáîâàë øèòü îáðàçîì ÷åðåç êàðòó (îáðàç ñíÿò ñ t-mobile 1.01). Íà îáðàç íèêàêîé ðåàêöèè.
Äàëåå ïðîáîâàë ñíÿòü îáðàç ñ ïðîáëåìíîãî àïïàðàòà. Àïïàðàò âûêëþ÷àåòñÿ. Åñëè ñ mtty äàòü êîìàíäó øèòüñÿ s2d, òî mtty ãîâîðèò, ÷òî êîìàíäà íåïðàâèëüíàÿ

Hi,
Read this http://forum.xda-developers.com/viewtopic.php?t=46628 about the SD flash
M

thanks, but te problem is the device doesn't want to work with card. No reaction on the card with rom-image, turning off when typing d2s

Don't know where you bought & how much you paid for it (sure hope it's less then a new screen), but sir I guess you're scr*w*d.
Maybe you can replace your broken S110 screen with the one from the S100. There's a rar file on the board, with a detailed description & pictures on howto disassemble your magician, think it's called disassembly.rar.
EDIT You can find it here http://forum.xda-developers.com/viewtopic.php?t=44841
M

thanks, but I think the screen is alive, it shows usb or serial and etc.
As far as i know, there is some diagnostic tests to understand where is the problem. how to activate it?

Diagnostics
Sorry I don't know of a diagnostics test. But you can have a bootloader without a working rom. Since you bought the S100 in a bootloader state, that's very suspicious to me. & that's why I advised you to replace the broken screen on your S110 with the one from your S100.
Hope you can sort it out & if you happen to run across a diag. pls update the wiki with it.
Regards, M

S200 dead, ROM Update failed

hi
i have a QTEK S200. Today i tried to update my ppc with a WM6 version, but after 40min. the upgrade program crashed down.
After this it was impossible to enter in the main menu of the ppc. the ppc remains hanging on the QTEK screen. I've tried to enter in the bootloader with the color screen, to connect the ppc with my usb cable an the notebook, but my notebook does'nt find my ppc. And now the battery is empty (even connected with the usb cable on a working pc) and i can't switch on my ppc.
Any solutions?

Charge your Batterie and make Hard Reset. Charge VIA Caddy.

done. but the screen remains on the QTEK start page. Bootloader is possible and i get the 3-color screen but my notebook does'nt find my ppc... It's strange because yesterday everything was fine and the connection to my notebook was ok but in the 3-color screen i can't build a usb connection.

ok, problem solved. i've puted a new core on the ppc and now appears the old wm5.

how did you manage to get back to the old rom ? i am stuck on the qtek screnn and the only thing i can access is the USB flash 3 colors screen but my pc doesn't seem to the device...
any help greatly appreciate )
thx in advance
ben

do you have the problem with the SPL 3.08?

no I am in SPL 2.20... and IPL 2.09...
thanks for your help

please write the full ipl/spl number!

here it is :
IPL : 2.09
SPL : 2.20.0000
thx

finaly I manage to dowgrade it by changing my driver - the problem was coming from vista

important is to know, that the 3-color screen give the possibility to communicate with your computer (connected with usb).
so, you have the possibility to copy a new core on it. after that you put a new wm or you take the old one. in my case, the old wm5 was still on the ppc.
yesterday i was testing the wm6 in german but it was not really nice... so i work again with wm5 and wait till a complete wm6 solution is available.

Upgrade ROM without ActiveSync!

hi bro
My Herald have a big problem. it's freeze on the HTC spash screen and can't load the ROM. I've made a hard rest, it's done but the problem ist still present.
I've download the Windows Mobile 6 RUU on the HTC official site but it's impossible to do the rest because ActiveSync is not connected with my phone. How can i resolve my problem without ActiveSync?

see this post 6
this method work!
http://forum.xda-developers.com/showthread.php?t=340618

I've done all said in the forum you have indicate but nothing....
I fear that my device is not out!

WaveMaster1406 said:
hi bro
My Herald have a big problem. it's freeze on the HTC spash screen and can't load the ROM. I've made a hard rest, it's done but the problem ist still present.
I've download the Windows Mobile 6 RUU on the HTC official site but it's impossible to do the rest because ActiveSync is not connected with my phone. How can i resolve my problem without ActiveSync?
Click to expand...
Click to collapse
Have you placed the phone into bootloader mode before using the RUU? (Holding the camera down and pressiing the soft reset button?)

Activesyn won't recognize the phone if connected during bootloader ... but if the phone says "USB" on the bottom left, you can run the RUU and it will work.

My device display "USB" in bootloader mode when i connect it to my PC.
But the problem is that the pc can't detect a new device connected...
When i try to flash by the SD card my herald can't detect the card!
I'm affraid! Please HELP ME!!!

why you d´ont write more?
isp XXXXXXXXXX
spl XXXXXXXXXX
card formatted at FAT 32?
camera + comm + reset ?
and was see you
"card not recognized?"
i am not a profi, but if one one this read, can you help
i find this in herald forum from here, try it again, and again....
and answer.
Ciao

why you d´ont write more?
isp XXXXXXXXXX
spl XXXXXXXXXX
card formatted at FAT 32?
camera + comm + reset ?
and was see you
"card not recognized?"
i am not a profi, but if one one this read, can you help
i find this in herald forum from here, try it again, and again....
and answer.
Ciao
IPL 1.08.0001
SPL 1.08.0001
It's normal that i get same informations about IPL and SPL?
I've done the procedure to enter in bootloader mode
But my computer don't detect it and my device display "USB" in the white area
of bootloader screen (this is normal)
But i don't know why it can't read my card with HERAIMG.NBH file inside!!!
The version of my bootloader is not displayed. Is it normal?
Per aps my bootloader get to be flashed, but how can i do it if it's the source of my problem?
PLEASE YOU ARE MY LAST SOLUTION!

about ipl 1.08xxxx and spl 1.08 xxxxx (very bad problem)
http://forum.xda-developers.com/showthread.php?t=343760&page=2
1 you have original Ruu.,.,......ship.exe
try it again when you are in bootloader mode, and reply. goes or not?
2 you have your original ruu..........ship.exe
whit winrar extrat all, and you have to rename the ruusigned file (60MB or more MB not the file with 1 MB!, to HERAIMG.nbh.
if dont work i some not can help you i m sorry.
my device work after many problem again but i have no WLAN and i have not isp 1.08xxxxxxxxxx
i wish you can write very good new!

show in your computer
if you are in bootloader mode wiht herald
if you have a networkcard not active! reactive this now
i had wm5 and his sync automatic
but after data crash on herald with wm6 does not sync again,
i search in my computer and a have see that 1 windows mobile device card does not was connect and i have reconnect this. and momentanly works again good with wm5, wm6, touch flo
show, you have no other way
ciao

MDA Vario II wiht Bootscreen no Windows

Hello there,
i have a big Problem with my Vario II (Hermes) . My hermes starts not the Windows, but i can start the boot Screen with USB Connect.
I read many Wikis , but i don' t can update a new Rom.
My questions :
- in which order i must which programm start to update the ROM without ActiveSync
Herm300 IPL-1.01
Herm300 SPL-1.04
I hope you understand my english
Thanks
SpeedyGGG

Hello there,
i have a big Problem with my Vario II (Hermes) . My hermes starts not the Windows, but i can start the boot Screen with USB Connect.
I read many Wikis , but i don' t can update a new Rom.
My questions :
- in which order i must which programm start to update the ROM without ActiveSync.......................................
Click to expand...
Click to collapse
The easy way if you can get the bootscreen is to flash using a memory card,
there's plenty of guides.

copy hermimg.nbh into SD card max 1 GB and press Power+OK and rest with your pen in rest hole

Old P3300

Hi everybody,
I have searched the forum for a way to fix my old P3300, but I can't find.
I have this P3300 that was bought unlocked a long time ago.
One morning it was dead.
Now I can get to the bootloader screen (red, blue, green and white) with the following information:
IPL 3.13.0001
SPL 3.13.0000
I have USB link on the bottom and it is recognized by Windows XP.
When I try to run HTC_P3300_WWE_3.13.405.1_4.1.13.44_02.94.90_Ship_R.exe it detects the phone says that will upgrade from <blank> to 3.13.405.1. It starts but fails between 2 and 3% with error (228) invalid file size.
Am I doing something wrong or not and it's time to get a new phone?
Thanks for any assistance.

try update with sdcard,be work sure, copy nbh file from your rom into the sd card formated with fat32,rename ruu_sihned.nbh with ARTEIMG.nbh,put the card into the phone and wen open it pres down volume key

or,Remove the SD card from the phone,close activesync conection,run mtty and tipe "wdata" command,after this you can run your update utility