Hi i am new here and my hermes brick, no gsm, and splash on windows screen and i can not in in Kitl mode
I send my phone to reapair center and there want change the mainboard.
Can annybody help me? to get new mainboard?
I sent a bricked Hermes back for repair a couple of months ago and the motherboard was going to be more than 6 weeks from HTC, so I think it'll be difficult to get one from anywhere else.
But, before spending loads of cash on a new board, try posting here http://forum.xda-developers.com/showthread.php?t=286755 and someone may be able to help you fix the phone.
Give as much info as possible about your brick:
Which OS version.
IPL/SPL
Which radio before NO GSM message.
Is it hard SPL
Can you connect to PC and try to upgrade. If so, what is the error message.
Are you Super CID.
How did you brick the phone (eg power loss during upgrade etc).
There is a chance that someone can help - and it costs a whole pile less than a new motherboard (even if you pay the elf ).
Good luck.
closer66 said:
Hi i am new here and my hermes brick, no gsm, and splash on windows screen and i can not in in Kitl mode
I send my phone to reapair center and there want change the mainboard.
Can annybody help me? to get new mainboard?
Click to expand...
Click to collapse
I had befor orginal o2 rom germany, and have spl 1.09, and i want flash t- mobile hungary rom english rom, everythink runs fine flash without anyproblems. After finish phone restart and show no gsm and hang on windos mobile screen.
when my phone connect to pc in splash screen than activsync can not find. When i start in bootloader screen. 3 colors. yes than i can connect. but flashing any other rom not possible. i try all roms always same message.
My phone dont have anny CID annymore befor was super cid. But now i can not find anny cid
Related
I attemted to flash my Kjam to WM6 & it went dead. It wont start at all. Kjam Service centre says there is a problem in the mother board and it needs to be replaced for $ 300+........now if flash fails...the ROM must have gone corrupt , what has it to do with the motherboard ?
can anyone throw light on whats the real thing ?
Deven.
take out the battery for hours then re-install it. try to boot in bootloader mode first(3 colors). If it work, it's the time to re-flash the right rom now!
When you start the device up what happens?
Same Problem accured for me!!!!!!!
I installeda new rom and my device didn't power on after that.
What should i do now?
afghahi said:
I installeda new rom and my device didn't power on after that.
What should i do now?
Click to expand...
Click to collapse
Nobody here is providing any details so everything is going to be just a guess. If either of these phones were a G4 and you flashed a rom that tried to update the IPL/SPL then its very likely you have bricked your device. But again, with no information about what rom you were trying to flash, what your IPL/SPL were beforehand, or details about what it means that it won't turn on, everything is just a guess...
Bricked Kjam
its comletely dead.....i had disconnected the battery for a couple of days then connected it but it wont start....i checked the battery using multimeter it is fully charged....neither does it power ON when connected to mains...It doesnt get detected when connected to the USB port..thats obvious since it is not powering up...so cant flash it again.. now m in a fix as to whether to spend another fortune after this sweetheart or keep it in a showcase ....
Deven
( a bricked KJam )
If nothing lights up that looks pretty terminal. :-(
Maybe you could buy a broken Wizard with a working motherboard? Alternatively maybe sell off your mostly working Wizard on this forum to raise money to buy a new device?
Sorry if you can't get it going. :-(
please help! I have made a wrong ROM Update for my Artemis. The result is that it doeasn`t starts anymore. I see only the start screen no more. If i make a SW or HW reset tahn i see a 3 colored screen and USB. But i don`t get a connection via usb to my compute`! How can i wake up my Artemis ???
tell use more what did you do and how did you do it?
what artemis is it?
what rom was it
Flash went sour..
You need the original ROM which was on your device when you bought it. What version (HTC, MDA, etc..) and what language was the original ROM?
please i need help too
I guess I made the same or a similar mistake that dr.moppi did. My machine is a Dopod P800 from mainland china with the chinese operating system. I flahsed it with PDAMobiz_Dopod_P800W_AKU301_v1.1.2_PowerMap. Don't really remember what the original ROM was but now when i turn it on it freezes when it lights up. On the screen, it says
IPL 1.27.0001
SPL 1.27.0000
GSM 02.67.90
OS 1.28.0.0
DOPOD
I don't get a connection through usb to the computer either. I am not sure if I did the hard reset correctly. Didn't understand the instruction on that "press the soft key left and right and soft reset at the same time." Anyway, you guys are all experts, can you help me please?
it should be the same as my problem
if i remeber than i used the same ROM Update :-(
I hope anyone could give us a solution, please.
@dr. moppi we can only help you if we know what version you had before.
@empathyvirus you have to look for the original ROM which, in your case, should be the Chinese Dopod ROM. Install that one and your good to go.
Without the original ROM the only thing left to do is: sending your device to your provider or contact and sent it to the guys of imei-check. Either way, you'll probably have to pay to get it fixed.
how to install original rom
Thanks for your quick reply Pyth. In the case I get the original ROM from somewhere, how do I install it if I can't get a connection between the phone and my computer? Can you advice?
Put your device in bootloader by pressing the record button and reset at the same time. If you have your USB-cable connected between your PC and your phone it will indicate a connection by 'USB' in the left corner of your device. Now you should be able to run the ROM executable and update your device.
thanks anyway
i tried but it didn't seem to work. anyway, i have troubled you enough and maybe it's best i just go to the repair centre of dopod and pay for a fix. i really appreciate your help though Pyth.
Where can i find the t-mobile rom its the MDA Compact III that wont start for me
I had a BSOD on my laptop during a radio flash and was left with a phone that got stuck on boot screen, with NO GSM on the display and no KTIL possibilities. Sent it back to Brightpoint (HTC contracted repair shop) and they wanted 350 euros to replace the system board.
So before i sell as scrap on ebay - i wanted to check that i hadnt missed any miracle cure that may have been found.
Thx
try having a look in the Upgrading forum http://forum.xda-developers.com/forumdisplay.php?f=306
am sure there are a few unbrick topics there, think i remember seening some in there once
try here - http://forum.xda-developers.com/showthread.php?t=325018&highlight=No+gsm*
Thanks for the reply - have tried pretty much everything. My main issue is not having KITL
nmonger said:
I had a BSOD on my laptop during a radio flash and was left with a phone that got stuck on boot screen, with NO GSM on the display and no KTIL possibilities. Sent it back to Brightpoint (HTC contracted repair shop) and they wanted 350 euros to replace the system board.
So before i sell as scrap on ebay - i wanted to check that i hadnt missed any miracle cure that may have been found.
Thx
Click to expand...
Click to collapse
Are you on Hard-SPL ? Could you use PC to access the Hermes ? If so, try the method to flash the ROM with a memory card method.
Good luck
Memory card flash
Thanks QQ88 - I will give it ago when I get the phone back!
If that doesnt work is there anyone with serious phone skills (thinking of pof-a-likes here) wants to earn 100 euro to help get this phone back to life then PM me.
I''ll give this a shot.
nmonger said:
I had a BSOD on my laptop during a radio flash and was left with a phone that got stuck on boot screen, with NO GSM on the display and no KTIL possibilities. Sent it back to Brightpoint (HTC contracted repair shop) and they wanted 350 euros to replace the system board.
So before i sell as scrap on ebay - i wanted to check that i hadnt missed any miracle cure that may have been found.
Thx
Click to expand...
Click to collapse
This is a tricky one but I believe that you can use the same flash file that you were using and just try this:
You should know your SPL version before going too far with this. Hopefully you can get that info by trying to boot it and if it can get to the very first splash screen with the red text, it should show it there.
Turn on the phone and let it try to boot ... Hold down the Power and OK buttons at the same time and while holding those buttons down, hit the reset button at the bottom of the phone and you should then be given the multi-color weird screen that's given right before the flash. Then, connect it via USB. Load up the flash software and it should ask you which version you're running of the SPL, select it and then click next. Auto-detect won't work if I remember correctly. Then just push forward and it should go through.
If all else fails, look up Mr. Vanx's information ... he's quoted all over this site and has his own site that has a LOT of information about bricked hermes phones.
GOOD LUCK! I hope it works.
Had a similar problem last week. Download the ROM at the top of the link below and it should unbrick your phone. It worked for me
http://wiki.xda-developers.com/index.php?pagename=Hermes_Unbrick
Good Luck
Thank you to all that gave their input. Can confirm that I have tried all methods incl. SD flashing but due to corrupt CID and SPL 1.09 it is time to wave the white flag and give up.
Will keep up with the threads to see if anyone manages to find a way to resurrect TyTns with corrupt CID and SPL 1.09
I need some help!
I have a dopod C800. I have tried upgrading but have run into some difficulty.
The PDA will not go past the tricolor boot loader screen. The only writing is as follows. In the Red section.
RUU
IPL 1.09.0001
SPL 1.09.0001
I cannot get the Active Sync to go green (connect) but I know my computer can see the device as i get a sound when i plug the USB cable in.
Can help me and advise what I can do? I think i might have tried to HArd SPL.
Need help to unbricked herald
i have the same exact problem. some people say the phone is bricked.
http://wiki.xda-developers.com/index.php?pagename=PB_KITL_HERMES
i found this link, that shows that hermes can be fixed. Is there any justice or expert guru to get our phone unbricked
I went try to repair it and they say i gotta change the motherboard aka the machine. i was like ^&* since it cost $400, might as well by a new phone.
Hello
First I am many sorry if repeat but I still not know what I can do. I buy mobile and I thing is Type 2b (still on operator logo) but I don´t know how I can find solution, because I tryed flash with many roms and I tryed latest radio rom and everything done but when is finish it restart and than is still in orange logo (or HTC and etc). and about two seconds show NO GSM.
I have SPV m3100 with SPL-1.40.Olipro.
PLEASE help me I cant find solution !!!
Many thanks and many sorry if repeat threat
Try a hard reset. You DON'T have Hard SPL on your phone. It may be unlocked but it may not be Supercid. The best idea would be to flash the original carrier rom on to it and see if that fixes it THEN flash Hard SPL on it.....
Good Luck...
Its possible you may not be able to recover your radio rom...
Hello,
Thank you, but I tryed originall shipped rom and original rom from orange site. Everythings done fine. I tryed also radio rom and it done OK. I dont know what I can do.
Please can you send me links for there roms which I can flash?
I wish I can repair.
Thank you in advance.
If the shipped rom fails you are probably looking at a permanent brick. There are some other things you can try using MTTY but it may not be hopeful. This is one of the pitfalls of buying a "bricked" phone. It may not be fixable and you spent $$$ that could've been spent more usefully elsewhere...
Hello,
thank you for reply, and how I can use there MTTY and when I start it it is like other working pda and it flash led lights, only for second, like when you flash new rom and when start and then it flash light and then screen change for "tap on screen" but here only flash and dont change screen.
Do you know what I mean?
Does it say "tap on screen to setup"?
If so you may be looking at a bung digitizer. You will need to replace the LCD to fix this.
Hello,
no, it is only like it, it stay orange logo, but when "blik" "NO GSM" it blik all display and than stay in orange logo too
Do you thing if JTAG help me?
can't say, never used. You do need some technical skill to use the Jtag method...
yes I have some technical skills but I dont have any schematic of jtag cable.
EDIT: I find some pdf with two schematics:
1. Holly Gates' Schematics for the JTAG Dongle
2. Modified Schematic for the JTAG Dongle Circuit Using 74LS541
Which can I use?