Database Users

Charmer no signal :( any info or help

Hi to all in this forum.
I have one T-Mobile MDA Compact II PM200. In this forum i hound that his name is Charmer. I try to unlock it with Lokiwiz03a. Program give me a code but device says that code is wrong. I try with other software to unlock it and after that mobile work with SIM card but no signal
I reflash mobiele with WM6 founded her in the forum, not it have English (before have German) but again no signal. I try now to unlock it with Lokiwiz02a and choose CID unlock. Again no signal.
When device in Automatic search mode no found network. If in Manual mode found but unable to register in network. When i put mobile to my computer speakers no outgoing signal from mobile that's not normal.
What is the problem ?
Can onyone help me with information ot needed software ?
In moment mobile information is:
ROM version: 10.2.0.8 WWE
ROM date: 2/03/07
Radio version: 01.12.20
Protocol version: 4.0.13.23
Identity:
Model No.: WIZA200
Platform: PocketPC
IMEI: 35703700051525500
Hardware:
CPU: OMAP850
Speed: 195 MHz
...
I try to found information about this problem here in forum but w/o result.
10x in advance

Did you try to flash a new radio? 2.69 or 2.19?

No.
I found this files:
BREEIMG.zip
breeze.zip
inside breeze.zip are:
SSPL.exe
spl
breezessplv1.nb
inside BREEIMG.zip is:
BREEIMG.nbh
is this needed files for radio flashing ?
if not then what files I need to try with other radio version ?

I download Radio from ftp on this form for Prophet. And try with Prophet_G4_RadioRom_v2.47.11 but now mobile not start. Go to splash screen and after few seconds restart.
I try to put it in bootloader mode but ActiveSync can't make connection and for that flash software can't wreit new radio or flash into mobile.
I ry with:
1. dowenload this t-mobile official rom (http://www.tm-phonedownloads.com/files/RUU_Compact ll_2060227_20602110_021921_T-MobileUK_Ship.exe)
2. enter your Charmer into bootloader mode by pressing power + camera + reset, let go of the reset, but keep holding power + camera until the three colur screen will show up (that is bootloader mode).
3. connect the Charmer to your pc (make sure your battery is fully charged)
4. run the t-mobile rom.
5. good luck!
but ActiveSync can't make conection.
?

If you are in bootloader Active Sync wont make a connection. Just plug in the usb cable into your phone while in bootloader and run RUU.
Cheers,
vlodeck.

I try with this 2:
1. T-Mobile official rom RUU_Compact ll_2060227_20602110_021921_T-MobileUK_Ship
2. Prophet_G4_RadioRom_v2.69.21
T-Mobile official rom RUU_Compact ll_2060227_20602110_021921_T-MobileUK_Ship
===================================
inside are this files:
EnterBootloader.exe
nk.nbf
README.doc
ROMUpdateUtility.exe
RUUGetInfo.exe
RUUResource.dll
Prophet_G4_RadioRom_v2.69.21
========================
inside are this files:
EnterBootLoader.exe
nk.nbf
ROMUpdateUtility_G4.exe
RUUGetInfo.exe
RUUResource.dll
phone not start normaly. just start and after 5sec restart. i put it in Bootloader mode (press Camera, Power_buton and Reset. then release Reset and after few sec. mobile goto in Bootloader mode). when conect USB cable ActiveSync not find mobile and this file not make upadte/conection: ROMUpdateUtility.exe and ROMUpdateUtility_G4.exe
if I try to start RUUGetInfo.exe windows says that this is not valid Win32 application.
then what RUU to start ?
how to flash other Radio into this mobile or to reflash it again to be alive ?

anyone will help me for my problem ?
in moment when i start my pocetpc it displays:
IPL 1.12
SPL 1.12.0000
OS 10.2.0.8
the row GSM .... missing.
in moment i can't make connection with ActiveSync. then how to flash again mobile ?
now i try to flash it with RUU:
http://www.tm-phonedownloads.com/download_manager_mda_com2.html
http://www.t-mobile.de/downloads/?r...ku3.3_38222_382117_026921_tmo_de_ger_ship.zip
but it gives a error

i try with this:
http://www.my-audio.net/xda/Univers...s/Universal_Upgrade_v1.30.68_radio_1.09.0.zip
but when software start flashing says that this Utility is not for my device and to find right
?????

I'm guessing that this universal radio upgrade is for universal
Download this:
http://www.mobione.pl/pliki/ruu_252_eng.zip
Extract it, copy the .nbf of the rom you want to upgrade your device with to the extracted RUU folder. Once copied - run RUU.
P.S. The problem with your device is that you have upgraded wm6 on 1.xx bootloader. Thats why the system doesnt start. If the method I described above doesnt work. Post me.
Cheers,
vlodeck.

now i can bootloader mode,
i did it but got this error while i upgrade my rom to newest rom 3.3...
i got this "invalid command 326": please check your NBF data, this NBF data cannot be used for your PDA Phone.

hi again to all
after long time i try to play agian with this brick-PM200 that haven't signal.
last time (before more 2 years) i write ROM and after that PM200 not start, only in Bootloader mode (3 color lines).
today i revive it when flash this:
HTC_charmer_upgradeut_noid.rar
(
EnterBootloader.exe
nk.nbf
ROMUpdateUtility.exe
RUUGetInfo.exe
RUUResource.dll
)
PM200 start, in begin fave full signal. after 30-40 seconds signal gone (but not test in/out call). i try to restart mobile, try hardreset, try manual search on operator - all no result.
on start i put near radio but power amplifier not work. i think that this is harware problem.
but not 100% sure.
is possible this problem to be from wrong radio settings ?
i try to write different radios for Prophet but every time get message "Invalid tool" and radio flashers stop.
i try with universal radio thata Vlodeck says but again this message.
what to do ?
before two days i repair one HTC Touch Elf100 and read that can sniff USB comunication to check Vendor ID and other ID.
but in my PM200 this not work. on Elf100 work easy like is writed here in forum.
when start wyty (or what's name is) make connections with mobile but after write:
ruurun 0
says that need password. if try with password for Elf100 not accept it.
what is the password for Charmer (PM200) ?
or if there is other way to get Vendor ID and other ID how ?

I can help you maybe. You need to downgrade to Aku 2.2 using the original utulity. Then the Radio will be downgraded too. But nobody knows the exact way on how to do that. (Maybe Vlodeck knows that?) I'll try to get it this week and tell you then.
As for the password try CHARMER. I have never been able to test it with MTTY cause I don't get in the right mode but I think the olny possibility is CHARMER. Just try it with whatever tool you want.
Hope that was helpfull

10x for answer.
next day will test password and post result.
how to downgread to aku2.2 ?
if you find solution please post it.

today i try but w/o success:
Cmd>password charmer
Cmd>ruurun 0
Cmd>getdevinfo
Invalid command : getdevinfo
For a help screen, use command ? or h
Cmd>
i try and with passwrod CHARMER. result is same.
what are commands for MTTY that supported Charmer ?

OK you have the same problem I have. You have Cmd> in the window. To get the comands and the password working you need USB> instead of Cmd>. That is the same problem I have and I don't know how to fix it.

in moment i use MTTY 1.42
before 3-4 days i repayr one HTC Touch Elf100. and this MTTY work find. no problem that write CMD not USB.
terminal show CMD> i write commands and mobile answer w/o problem.
but in my Charmer not answer.
possible reason is access password. but not sure.

There are simple comands. And for them you don't need SuperCID. I tried them and they haven't worked too. So I think there is something else with it. Maybe the Bootloader locks all comands and you need a password for that too. But I don't know about that.

@ChrBeck
you try to make SuperCID SD card to have full access to mobile. and after that to try flash it with RUU ?
next morning will try this.
p.s. now find this:
http://www.tm-phonedownloads.com/
http://t-mobile.iris-global.com

Well, we can't SuperCID and Security unlock a Charmer with a bootloader over 1.x at the moment. This is surely impossible. That won't work using a SD Card too. So I think you will not have any luck.

replace gwes.exe

Who can assists me replacing the gwes.exe on a Toshiba G500 smartphone?
I was so silly to buy this phone instead of trusting in htc's
No updates available from Toshiba, no helpfull email replies.
Many applications are not working due to gwes.exe error.
Toshiba just replies : no this software and the other asked doesn't run on G500.
So i have to help myself to get the most out of the misery.
On the phone is WM5 with AKU 3.2
Does someone have the files gwes.exe and gwes.exe.0407.mui from another WM5 release and can upload them.
How can i replace them? Due to the fact that gwes is running in the background i can't delete or rename it.
Also the files in the windows dirctory are protected.
Who can help me?

xda-graphite said:
Who can assists me replacing the gwes.exe on a Toshiba G500 smartphone?
I was so silly to buy this phone instead of trusting in htc's
No updates available from Toshiba, no helpfull email replies.
Many applications are not working due to gwes.exe error.
Toshiba just replies : no this software and the other asked doesn't run on G500.
So i have to help myself to get the most out of the misery.
On the phone is WM5 with AKU 3.2
Does someone have the files gwes.exe and gwes.exe.0407.mui from another WM5 release and can upload them.
How can i replace them? Due to the fact that gwes is running in the background i can't delete or rename it.
Also the files in the windows dirctory are protected.
Who can help me?
Click to expand...
Click to collapse
Sell your Toshiba, and buy a HTC.

xda-graphite said:
Who can assists me replacing the gwes.exe on a Toshiba G500 smartphone?
I was so silly to buy this phone instead of trusting in htc's
No updates available from Toshiba, no helpfull email replies.
Many applications are not working due to gwes.exe error.
Toshiba just replies : no this software and the other asked doesn't run on G500.
So i have to help myself to get the most out of the misery.
On the phone is WM5 with AKU 3.2
Does someone have the files gwes.exe and gwes.exe.0407.mui from another WM5 release and can upload them.
How can i replace them? Due to the fact that gwes is running in the background i can't delete or rename it.
Also the files in the windows dirctory are protected.
Who can help me?
Click to expand...
Click to collapse
Hi,
I don't know what you can do replacing such files, ( I think you must first make a dump of the rom, reconstruct it with the new files and then repack an flash again ) anyway you can try to extract gwes.exe and gwes.exe.0407.mui from the localized emulator on Microsoft web site... search with google for that if you don't have the link, I don't remember it now...
Really hope this help

Do you try to do a hardreset?

Surely you could use pput from ITSUTILS to drop the replacement files in, and then do a soft reset?
As for the files themselves, you'll just have to hope someone sends them to you

a majority of these errors was not caused by gwes.exe itself, i think. if you installed any software recently, uninstall them and try again

Hey guys, thank You for Your help. Never expected this resonance after the first reply
@[email protected]
you can try to extract gwes.exe and gwes.exe.0407.mui from the localized emulator on Microsoft web site...
Click to expand...
Click to collapse
just extracted it from WM5, but complete crash after replace
@THEVK
Do you try to do a hardreset?
Click to expand...
Click to collapse
a few times with no success
@Aquilo
Surely you could use pput from ITSUTILS to drop the replacement files in, and then do a soft reset?
Click to expand...
Click to collapse
just replaced the files with pput, but after soft reset complete crash of the phone.
@dandycheung
a majority of these errors was not caused by gwes.exe itself, i think. if you installed any software recently, uninstall them and try again
Click to expand...
Click to collapse
after a hardreset just installed tomtom -> crash
TomTom 5.21 / 5.20 both worked on my old xda graphite with WM5 but with another AKU version, i think 2.xx (don'T know bc. it's in the cellphone-heaven)
Don't know further, i have no ideas, maybe you guys

sell this and DO NOT buy htc!

gwes.exe is device dependant, so your phone wil never work with another device's version.

gwes.exe is device dependant, so your phone wil never work with another device's version.
Click to expand...
Click to collapse
no. it's device independent, but can have different components.
Also you can't replace it directly.
just extracted it from WM5, but complete crash after replace
Click to expand...
Click to collapse
it contains relocations. Do you fix it?
Also it must be signed.

Maybe this is interesting for someone:
left software button + power on
RUU update!
Waiting USB Connection ......
connecting usb cable
Updating
Receive call + power on
Factory update!
udc_enable
usb connect
Error occured, usbdev ep0 stalled!
and on Windows -> Driver installer -> TFW USB Download DR/V -> no driver found
(1 + power on) or (vol + power on)
PB Update!
Connecting...
INFO: Trying to initialize USB RNDIS...
HostMINIlnit:: !!
Rndis:: initialization: with addr=0
Rndis:: initialization!
Rndis:: Get MAC address yyyy,yyyy,yyyy
Rndis:: initialization: Fail!
ERROR: Failed to initialize Bulverde Rnd is USB Ethernet controller.
ERROR: Failed to detect and initialize Ethernet controller.
usb connection + 1 + battery connect
PB Update!
Connecting...
INFO: Trying to initialize USB RNDIS...
HostMINIlnit:: !!
Rndis:: initialization: with addr=0
Rndis:: initialization!
Rndis:: PDDInit Success!
Rndis:: Get MAC address XXXX,XXXX,XXXX
xxxx -> maybe device specific numbers
.
.
and on Windows -> Driver installer -> Microsoft RNDIS KITL for Intel PXA27x no driver found
.
.
Rndis:: initialization: Fail!
ERROR: Failed to initialize Bulverde Rnd is USB Ethernet controller.
ERROR: Failed to detect and initialize Ethernet controller.
4 + power on
KITL Enable...
Cellphone remains in "Toshiba Startscreen"
* + power on
SDCard update!
.
.
TFW Windows Mobile PDA SW DOwnload!
Initilization T-FLASH Card... SD Card CMD: Card Response timed out: 0x2142Initlization card fail!
Initilization T-FLASH Card... SD Card CMD: Card Response timed out: 0x2142Initlization card fail!
with MiniSD Card in slot:
* + power on
SDCard update!
Sectors per cluster: 32
First FAT Sector: 98
FatSectors: 31
First Dir sector: 160
First Data Sect : 192
Root DIR Entry Count: 512
...Dirctoy listing...
Search root dir fail!
fat search sector: Fail (fat_locate)
Find file fail!
Open file Error
Upgrade Fail!
0 + power on
------------------------
Xloader Version: MDOC4(mcp25) V1.00
Eboot Version: Eboot-1.02-00
(1) Download with USB_RNDIS
(2) Boot from IPL KITL enable
(3) Boot from IPL KITL disable (default)
(4) Test Key Value
(5) Test Memory
(6) Run ULDR. default FALSE
(7) Clean Reboot
(8) Abnormal Reboot
(9) Goto Sleep
----------from oallog------------
-----------------------------
Enter your selection:

This is your bootloader menu. All devices have some version of it.
Though all manufacturers put an option to upgrade in to their devices (just in case and for internal test purposes) few bother actually releasing updates.
There is no way to just replace gwes.exe and have the system working. What you need is a whole new ROM, so unless you can find someone cooking one I guess you are out of luck.

Thanks levenum,
i agree, there is no way just replacing it.
Just spoke to Toshiba support.
I asked for a hardware reset -> he searched and searched -> and told me "on this phone no way to do a hardware reset"
I ask myself WHO is working on toshiba support?
Why couldn't he say: press "0" + power on and then press 7
Does somebody know how to backup the rom e.g. on sd-card.
Flashing from sd card is possible with * + power on, but i don't know the filename the phone is requiring, and dont have one. Maybe after rom-dump the file will be known.
Toshiba also upgrades the G900 modell only by sending it in. There is no rom-update on the net. Maybe if someone tries (and knows) to backup the G900 rom maybe there is a chance to kook to WM6 for the G500.

Toshiba G500 Call outgoing problem
Toshiba G500 Call outgoing problem.But Idid formeted it "Format user partition" system. After have same problem & all incoming call ok.
any 1 will can give me solution for this problem ?

Error 260 on SVP M3100 HERM100

Hi, I hope someone out there can shed some light onto this problem. This is what I have: Orange SVP M3100; Operator: 14.123.1.614; ROM Ver.: 1.23.61.4; ROM Date: 07/13/06; Radio Ver.: 1.06.00.00; Protocol Ver.: 32.37.7010.01H.
I've downloaded and successfully (I think) flashed Hard-SPL-V7.
Bootloader used to read: HERM100; IPL-1.01; SPL-1.04.
Bootloader now reads: HERM100; IPL-1.04; HERM100; SPL-210.Olipro.
The phone still works and syncs. properly, but when I try running SPV_M3100ROMUpdate_0407, it eventually returns Error 260 (Update utility cannot connect to your PDA Phone.) This happens in Vista Ultimate and in XP Pro.
The program will go as fare as identifying the current image as Ver.: 1.23.61.4 and suggests to replace it with image Ver.: 2.11.61.1 however, when I click on OK, it puts the phone into Bootloader mode, disconnects the USB connection and unable to reconnect again. After this I have to do a soft reset and everything goes back to normal.
I'd very much appreciate any ideas to help me get around this conundrum. Many thanks.

put device into bootloader and try flashing from there, otherwise try sd card

OK, I could not flash from Bootloader either; same error message.
Extracted the SVP_M3100ROMUpdate_0407.exe onto the SD card.
Ended up with the following files: EnterBL.exe; GetDeviceData.exe; README.doc; ROMUpdateUt.exe; RUU.dll; RUUUI.dll; RUU_signed.nbh.
None of the above files will run on the PDA. What do I do next? Sorry for being such a novice and thanks again.

commnet said:
None of the above files will run on the PDA. What do I do next? Sorry for being such a novice and thanks again.
Click to expand...
Click to collapse
Correct, the files are not run from the device.
The hermes wiki has the directions for flashing from an SD card, go check it out.

Thanks for that jdc. I found the information you have suggested and here is what I did so fare:
-Formatted the SD card.
-Renamed the ROM image file to HERMING.nbh
-Inserted the SD card with the renamed image file into the phone.
-Restarted the phone and confirmed that it was reading from the card.
-Put the phone into Bootloader mode by pressing PWR+OK+Reset.
The multi-colour Bootloader screen comes up and nothing else happens. I'd tried pressing the PWR button just in case, but it had no effect.
Any more ideas? THANKS!

SPV m3100 upgrade - error 260 - connection drops when allowing enterBL.exe to run on
Hi - am going through the same process to upgrade my SPV m3100.
I've followed Mr Vanx's guides to the letter - ROM update from 1.23.61.4 to Hard-SPL-2.1 - as soon as i click 'yes' on the phone to allow enter.BL.exe to run - the connection between phone and laptop immediately drops.
I've tried using different USB ports as suggested in different threads = but to no avail
Am running Vista Home Premium.
I'm a novice so sorry for sounding stupid - any help would be really appreciated.

I had the same error until I disabled the phone lock. Worked ok after that

I had this problem for awhile, and I'm using Vista. I can't remember the problem to explain it, but I did one of 3 things to fix it.
1. Follow Mr Vanx's Vista Guide. The most important part is downloading his attached drivers and getting Vista to detect your phone as an "HTC USB Device" or "HTC USB Sync" or something like that.
2. Then I would recommend installing the official ATT Rom, you can download it off of HTC's website.
3. Install Schaps Advanced Config cab, and disable "security warnings"
After this done, you should be able to install a cooked rom from here.

Help needed

I just bought a used TMobile MDA. I was told that the phone was unlocked. When I tried to flash the phone it losses connection and I get the error ROM UPDATE UTILITY MFC APPLICATION failed. Can someone help me figure has what is causing this problem and how can I correct it so I can update the ROM on my phone.
IPL 3.08
SPL 3.08
GMS 02.69.11
OS 2.26.19.2
Any help will be wonderful.

Is your phone in Bootloaders or boots up into a working OS,if its working,download WST_4.2.2 tool and run the 'CIDAction' button to verify its CID lock/unlock status,then do accordingly.

zabardast_1 said:
Is your phone in Bootloaders or boots up into a working OS,if its working,download WST_4.2.2 tool and run the 'CIDAction' button to verify its CID lock/unlock status,then do accordingly.
Click to expand...
Click to collapse
When I tried to run the CID Action on my phone I got this:
Error! No device detected!
Try reading again; if it fails again then check cable
connection and be sure that ActiveSync's icon is
green.
Be sure to enable RAPI communications and
Applications Policy!!
I made sure that the phone was connected and then I tried to make sure RAPI communication and Applications policy was enabled. I got the same connection failure error. I don't know what to do to correct this error.

Does the phone establish connection or activesync through usb ? if it does,than,there are two files in the installation folder of WST_4.2.2 in the 'files' folder 'EnableRapi' and 'Cert_SPCS' copy these both zipfolders anywhere in your phone and execute them in the phone,then run the WST Tool.

zabardast_1 said:
Does the phone establish connection or activesync through usb ? if it does,than,there are two files in the installation folder of WST_4.2.2 in the 'files' folder 'EnableRapi' and 'Cert_SPCS' copy these both zipfolders anywhere in your phone and execute them in the phone,then run the WST Tool.
Click to expand...
Click to collapse
Yes, the phone does establish connection throught activesync. I did install both files, EnableRapi and Cert_SPCS, and excuted them the phone. WST still gave me the same error.

which windows are you using and what version is Activesync ?.
'MFC' (Microsoft Foundation Classes) failure is usually ,when certain application/program fails to initialize.
Do this all on winXP SP2 and use latest version of Activesync 4.5.Close/disable any Antivirus/Firewall running and try to end as many applications/programs running in the background through 'Windows Task Manager'.End Process 'WCESCOM' something running in the Task Manager.

[Q] Is there a tool for checking the nand memory for bad blocks ??

Is there a tool for checking the nand memory for bad blocks ??
My htc hd2 cant boot. NO WAY to boot in Android or WM. I tried to flash Everything. Now there are bad blocks and something like that. I think my nand memory is corrupted and i want a tool which can check that.
PLS hELp me! I want my htc hd2 back ...

Quick help .. but "measure twice and cut once"
Driver: http://www.kyou.cz/prg/hd2/as_drivers.zip
Program MTTY : http://www.kyou.cz/prg/hd2/mtty1.42.zip
(You can try to find newer versions, if you want ..)
1. How to check and repair bad block
a). Please make sure that you are SuperCID and you understand the importance of hard spl as this maybe a dangerious operation for you.
b). Downloan Mtty.exe file in the attachment below and save it to your computer.
c). Open connection setting of your activesync or WMDC on your PC and disable "Allow USB connection".
d). Put your divice into Bootloader mode and connect to your PC via USB
e). Run Mtty.exe from your PC
f). Selec "USB" in port box and then click OK
g). Press Enter once or twice to let the screen dispay "USB>" or "CMD>"
h). Type "info 8" to check if your device has bad blocks. And if there are any,
i). Type "task 2a" to fix the bad blocks.
Then go to bootloader and flash official winmo.
And other info here:
http://forum.xda-developers.com/showthread.php?t=1189544 (HD2)
http://forum.xda-developers.com/showthread.php?t=1033526

cubexe said:
Quick help .. but "measure twice and cut once"
Driver: http://www.kyou.cz/prg/hd2/as_drivers.zip
Program MTTY : http://www.kyou.cz/prg/hd2/mtty1.42.zip
(You can try to find newer versions, if you want ..)
1. How to check and repair bad block
a). Please make sure that you are SuperCID and you understand the importance of hard spl as this maybe a dangerious operation for you.
b). Downloan Mtty.exe file in the attachment below and save it to your computer.
c). Open connection setting of your activesync or WMDC on your PC and disable "Allow USB connection".
d). Put your divice into Bootloader mode and connect to your PC via USB
e). Run Mtty.exe from your PC
f). Selec "USB" in port box and then click OK
g). Press Enter once or twice to let the screen dispay "USB>" or "CMD>"
h). Type "info 8" to check if your device has bad blocks. And if there are any,
i). Type "task 2a" to fix the bad blocks.
Then go to bootloader and flash official winmo.
And other info here:
http://forum.xda-developers.com/showthread.php?t=1189544 (HD2)
http://forum.xda-developers.com/showthread.php?t=1033526
Click to expand...
Click to collapse
Thank you for your answer. Now i started mtty.exe as Admin (I have Windows 7) and i have done all the steps you said. But there is no USB in the port box. I can only select COM1 or COM2 but then mtty gives me an error. Any Solution?
Thanks

Did you use the driver that I mentioned in my last post? The situation that you described happens when you don't use the driver.
(If you are using windows 7, you need to install this driver instead of original HTC Sync driver. But it should be a little problem. Maybe the most easiest way is to find some PC with Win XP, there should be no problem ..)

cubexe said:
Did you use the driver that I mentioned in my last post? The situation that you described happens when you don't use the driver.
(If you are using windows 7, you need to install this driver instead of original HTC Sync driver. But it should be a little problem. Maybe the most easiest way is to find some PC with Win XP, there should be no problem ..)
Click to expand...
Click to collapse
Thank you i tried it on Windows XP and i could connect to my htc hd2 but mtty.exe cant remove the bad blocks and the phone wont boot.
Then i saw another command (TASK 8) in a forum and hoped that this would help but now i have a white screen !! No HTC LOGO... pls help...

Not really sure, but the white screen (without HTC logo) should be normal after this task .. but now you are able to go to bootloader (VolDown), right? So just try flashing official winmo directly from SD card via bootloader (<4GB).
Just for information what was an ouput of the "info 8" command (h.)?

cubexe said:
Not really sure, but the white screen (without HTC logo) should be normal after this task .. but now you are able to go to bootloader (VolDown), right? So just try flashing official winmo directly from SD card via bootloader (<4GB).
Just for information what was an ouput of the "info 8" command (h.)?
Click to expand...
Click to collapse
Yes i can enter the bootloader )
Ok now i tried to flash the official winmo rom but the phone is stuck at HTC Logo and wont boot into winmo.
mtty report(info8):
BLOCK 1686 (0x696) is bad block
BLOCK 2392 (0x958) is bad block
BLOCK 2409 (0x969) is bad block
BLOCK 3393 (0xD41) is bad block
Partition(0), type=0x20, start=0x2, total=0x63E
Partition(1) type=0x23 start=0x640 total=0xA40
partition(2) type=0x25 start=0x1080 total=0x1D340
partition(3) type=0x4 start=0x1E3C0 total=0x197C0
CE Total Length(with sector info)=0xF2D1E00
CE Checksum Length(without sector info)=0xF1E0000

The output looks fine and task 2a should repair it. If not, try other threads here on xda for other HTC devices (e.g. Diamond). You can copy output from task2a here.
Maybe somebody else will take a look on this problem.

cubexe said:
The output looks fine and task 2a should repair it. If not, try other threads here on xda for other HTC devices (e.g. Diamond). You can copy output from task2a here.
Maybe somebody else will take a look on this problem.
Click to expand...
Click to collapse
I really tried now all commands with mtty i think the nand memory is totally damaged. But anyway i really really ThAnK yOU for your support !! Thank you cubexe )

Worked
Saved my butt.
I had to get my HD2 to service and restore it to stock after flashing Android.
Problem was that by flashing every version of WM I never got past the startup orange screen (it kept rebooting).
Now it installed fine after checking and fixing memory errors.
I'm curious if it fixes the other problem too but not gonna keep my fingers crossed, seems to be a temperature problem.

Can't install driver
How do you install the driver?
I get the error message: "the inf file does not support this method of installation" when using the "right click > install" method.
I also tried to update the HTC sync driver in device manager and pointing it to the driver files but that didn't work.

hmm.. I have only windows 7.. any other alternative way to check would be great.
Thanks in advance.

sbhas2k said:
hmm.. I have only windows 7.. any other alternative way to check would be great.
Click to expand...
Click to collapse
Run XP in a virtual machine using Windows Virtual PC?
http://www.microsoft.com/windows/virtual-pc/

This is my log..failed! :/
--- 2K bytes sector version ---
DEVICE NAME=hynix_h8BES0UQ0MCP
DEVICE ID=0xBC
DEVICE MAKER ID=0xAD
PAGE SIZE=0x800
TOTAL PAGE SIZE=0x840
BLOCK COUNT=0x1000
BLOCK PAGE=0x40
Checking block information
BLOCK 0 (0x0) is reversed block
BLOCK 1 (0x1) is reversed block
BLOCK 2 (0x2) is reversed block
BLOCK 3 (0x3) is reversed block
BLOCK 8 (0x8) is reversed block
BLOCK 10 (0xA) is reversed block
BLOCK 11 (0xB) is reversed block
BLOCK 12 (0xC) is reversed block
BLOCK 13 (0xD) is reversed block
BLOCK 14 (0xE) is reversed block
BLOCK 15 (0xF) is reversed block
BLOCK 28 (0x1C) is reversed block
BLOCK 29 (0x1D) is reversed block
BLOCK 30 (0x1E) is reversed block
BLOCK 31 (0x1F) is reversed block
BLOCK 126 (0x7E) is bad block
BLOCK 2428 (0x97C) is bad block
BLOCK 3547 (0xDDB) is reversed block
Partition[0], type=0x23, start=0x2, total=0xFE
Partition[1], type=0x0, start=0x0, total=0x0
Partition[2], type=0x0, start=0x0, total=0x0
Partition[3], type=0x0, start=0x0, total=0x0
CE Total Length(with sector info) = 0x80800
CE CheckSum Length(without sector info) = 0x80000
Cmd>task 2a
Format ALL start
backup SPL OK
backup MISC configuration OK
SPL start start block=497, total block of CE=3599
erase_page - error bad status: 0xB791E960
ERASE block 126 FAIL !!!
erase_page - error bad status: 0xB791E960
ERASE block 2428 FAIL !!!
Write 0xFF start page=0x7C40, total page=0x383C0
restore SPL OK
restore MISC configuratoin OK
restore MFG configuratoin OK
Format ALL end