Error 260??? Rom upgrade--what am I doing wrong? - P3600 General

Hi all
I keep getting Error 260 when trying to run the Dopod ROM on my trinity.
So far I
- hooked up Trinity to USB
- Synced
- ran SSPL on Trinity to get to Bootloader mode
noted on screen is
TRIN100
IPL-SSPL by Des
TIN100
SLP-1.07.ds
- I run The WWE Dopod ROM
- Click ALLOW (running Vista Business)
- Click I Understand and NEXT
- Click I Completed and NEXT
I wait....and....ERROR {260}: Connection
Anyone else have this issue?

Try to run the SSPL before putting in the USB Cable. As soon you can see the mentioned screen:
TRIN100
IPL-SSPL by Des
TIN100
SLP-1.07.ds
put in the USB-Cable and wait until the Letters "USB" show up in the lower part of the screen. Now your Phone is connected and you should try again to update.

Borbosch said:
Try to run the SSPL before putting in the USB Cable. As soon you can see the mentioned screen:
TRIN100
IPL-SSPL by Des
TIN100
SLP-1.07.ds
put in the USB-Cable and wait until the Letters "USB" show up in the lower part of the screen. Now your Phone is connected and you should try again to update.
Click to expand...
Click to collapse
On my laptop, when I plugged in the USB cable after running the SSPL, Windows had to load a new USB driver, it loaded automatically, then showed "Ready to use new hardware". Then the serial on the Trinity screen changed to USB. If it doesn't work, reboot your phone and your computer and try again.

I have Started SSPL prior to connecting via USB -- Waited until USB appears on the trinity. Error 260 -- still
I noticed in the device manager it installs HTC USB Sync. It may have something to do with that -- i will try -- try again.

Try to disable USB connection in ActiveSync so that it doesn't interfere.
Also, make sure Trinity shows "USB" and not "Serial" on the white stripe in SSPL boot.

I tried disabling the USB in active sync. I also tried turning the USB connection in the Settings part of the Trinity -- still the same error.
I have to try this on an XP system.

Success! I tried it on an XP Machine -- and it worked. I guess there are issues still with Vista/Sync/Rom upgrades.
Thanks for everyone's help!

Related

Prophet Keeps Crashing My PC

Hi,
My Prophet has caused my PC to crash more than 3 times and I need some help.
I have read a lot of threads on the forum, but haven’t come across anything that sounds like the problem I am having.
My PC usually crashes right after I plug in my Prophet through USB or if it is plugged in, right after I unplug it.
Immediately after, I get the Blue Screen of Death with the message which references the following:-
DRIVER_IRQL_NOT_LESS_OR_EQUAL
It also has the following Tech Info.
*** STOP: 0*0000000D1(0*BA741E10, 0*00000002, 0*00000001*0*A8293BEB)
*** RNDISMPX.SYS Address A8293BEB base at A828F000, Datestamp 43584898
It seems that I do not have the correct USB drivers on my PC for my Prophet. Where can I download the most recent drivers to stop my PC from crashing?
Anyone able to send them to me?
Also, Activesync fails to recognize my PPC when it is plugged in with the USB, it goes through the sequences where it says “connecting” forever but never connects to the device.
The BT connection has been working well for me so far, but without a stable USB connection to Activesync, I cannot upgrade my Prophet to WM6.
I have turned off the firewall and install, re-installed Activesync, I have Hard Reset my device a couple of times. In the end Activesync fails to connect to my device and then I usually end up crashing my PC.
I am open to some suggestions, thanks
Prophet Specs:-
IPL:- 1.00
SPL:- 2.20.0000
ROM:- 2.20.7.34. WWE
Model:- PM 300
PC Specs:-
XP SP2
Activesync 4.1 and 4.5
Remove the drivers from the pc for the prophet, plug prophet back in and let windows sort it out for you.

Very Urgent update to WM6 fail

Dear all
I try to update my PPC 6600 from WM2003 2nd edition to WM6. I download and run WM6 OS 5.2.2000 (Build 20000.1.0.0.PV.HAT). After I try to finish the last step of the installation which is to cool reset the PPC, there are 4 color bands and only show "NO GSM", "D 5.70.11 WWE". I try to turn it off, but doesn't work. I try to connect back to PC, but PC can not find this device
Please help
http://wiki.xda-developers.com/index.php?pagename=BA_FAQ_STUCK_AT_STARTUP
imatrix said:
http://wiki.xda-developers.com/index.php?pagename=BA_FAQ_STUCK_AT_STARTUP
Click to expand...
Click to collapse
I have tried, but not work, no format, no reset, stay the same
here is the message from the program. please help
USB>
USB>set 14 0
HTCST ÚÈHTCEUSB>set 14 0
HTCST ÚÈHTCEUSB>task 28
DOC_format_HW+
DOCInfoTableinitHW+
Binary0:dwSize=80000
BINFS0:dwSize=0
FAT0:dwSize=1000000
FAT1:dwSize=EA0000
All:dwSize=1F20000
USB>task 0
USB>
I am very sorry, but I need help.
I am unable to fix this.
I am trying my best to follow the instructions and dont know where am i going wrong.
Like U said,
I went again with the Multi Port TTY utility and in the new USB text file window, ((stopped the wcescomm.exe application from taskbar)
I tried entering
set 14 0
USB>task 28
USB>task 0
USB>
Saved the file as USB
The phone in the cradle was still showing USB v1.02
I took the phone out of the cradle, removed the battery and inserted it back into the cradle
and i again starts showing USB v1.02
Where am i going wrong..
I also tried
USB>set 14 0
USB>task 28
USB>task 0
USB>
but in vain...
Please help in resolving this
I found http://forum.xda-developers.com/archive/index.php/t-273871.html online and the problem is almost identical as mine. Please help
i think u can flash it again
woi700 said:
i think u can flash it again
Click to expand...
Click to collapse
What do you mean flash it again?
It can not be detected by activesync
cables
Something like that happened to me a while back where i couldnt connect. The problem wasnt the BA but was the cable connections- usb cable connections. It stills happens today where i get a bad connection and i have to play around with the usb that is plugged into my laptop. Maybe you should check out how loose your usb connection is--try moving the cable around.
shazzy84 said:
Something like that happened to me a while back where i couldnt connect. The problem wasnt the BA but was the cable connections- usb cable connections. It stills happens today where i get a bad connection and i have to play around with the usb that is plugged into my laptop. Maybe you should check out how loose your usb connection is--try moving the cable around.
Click to expand...
Click to collapse
I have tried many time, but not work
reflash
get into boot loader mode, connect directly to pc with good direct usb connection, (screen should state, USB from SERIAL on connection), reflash.
ensure SD card is removed beforehand.
AbuGWM5 said:
get into boot loader mode, connect directly to pc with good direct usb connection, (screen should state, USB from SERIAL on connection), reflash.
ensure SD card is removed beforehand.
Click to expand...
Click to collapse
What do you mean reflash?
Does it mean that Reinstall the WM6, or install other OS like WM5?
However,Without activesync how can I do that?
OR reflash mean formart?
I try to fomart my ppc, but stuck in the white screen
Note: I have tried the following
http://wiki.xda-developers.com/index...UCK_AT_STARTUP
If you can get USB connection to your device, you can just try to reflash with same WM6. best of lucks.
restart your PC
Try reinstalling active sync on your PC or laptop and then shutdown your PC or laptop and then restart it. Then try connecting your BA afterwards.
shazzy84 said:
Try reinstalling active sync on your PC or laptop and then shutdown your PC or laptop and then restart it. Then try connecting your BA afterwards.
Click to expand...
Click to collapse
I did what you said, but my PC is still unable to detect my pocketPC.
In the pocketPC bootloader mode, I can see it change from serial to USB after I connect the usb bundle. What should I do?????
king2004c said:
Dear all
I try to connect back to PC, but PC can not find this device
Please help
Click to expand...
Click to collapse
try to disable windows firewall and any other firewall then try...
i have same problem my device can't connect to pc when i disable ISA firewall my ppc connected .
AddAn
addan said:
try to disable windows firewall and any other firewall then try...
i have same problem my device can't connect to pc when i disable ISA firewall my ppc connected .
AddAn
Click to expand...
Click to collapse
I have followed what you say, but still not work
I hear some people say that I can reflash the rom.
But
1. I don't know which rom they mean, my orginal one or updated one?
2. How can I get my original rom?
Someone say that if I try to connect via activesync under PPC bootloader mode, I could not see any connection in activesync, but I will hear some connection sound, then I can reflash my rom
But
1. How can I do anything if I can not see any connection in activesync
I have done what people say about using mytt1.24.
But,
What should I expect to see?
king2004c said:
Dear all
I try to update my PPC 6600 from WM2003 2nd edition to WM6. I download and run WM6 OS 5.2.2000 (Build 20000.1.0.0.PV.HAT). After I try to finish the last step of the installation which is to cool reset the PPC, there are 4 color bands and only show "NO GSM", "D 5.70.11 WWE". I try to turn it off, but doesn't work. I try to connect back to PC, but PC can not find this device
Please help
Click to expand...
Click to collapse
go here ftp://xda:[email protected]_1.15_Type_II/BA Radio 115 THIS WORKS.rar then use this to load your gsm extract BA Radio 115 THIS WORKS.rar somewere on your computer put your ba it to bootloader mode then put i into its craidle then run MaUpgradeUt_noID.exe wait till upgrade is done then take out of the craidle press reset button dont worry about activesync connecting
or not
update information
I tried to upgrade my win2003 2nd edition in ppc 6600 to WM6, but it seems that WM6 won't work with ppc 6600. Then,
1. I download the WM5 rom from http://wiki.xda-developers.com/index.php?pagename=Helmi
2. Try to reflash the PPC
3. I see that the PPC response
4. Try to do the reset after finished upload rom
5. Four color strip screen & "NO gps" and "5.02... WWE"
6. Try to restart again, and wait, result is the same
7. Try to go to bootloader mode, use mtty, do "set 14 0", "task 28", "task 0", PPC still keep the same. I have tried all reset, hard reset, etc
8. *** Try to reflash the PPC again, I find out that there is no current ROM when the ROM upload program try to read my current PPC condition.
PPC6600 is a CDMA device and not a GSM, so you tried to flash a wrong ROM, sorry friend.
April 1 said:
PPC6600 is a CDMA device and not a GSM, so you tried to flash a wrong ROM, sorry friend.
Click to expand...
Click to collapse
could you please tell me where I can find the corret rom?

Done all, can´t syncronize!!! Help

Hello to everybody!
After all I have to say that this is a fantastic forum for users of Qtek S200 (Prophet). I bought one last week and started to see what I could do. Therefor... I'm a newbie
This is my first thread, hope that some one can help.
After trying to understand the world of Prophet, I first changed the ROM to an official Qtek ROM.
Now I what to sincronize with my PC to transfer photos and put some software and apps in the card. Like I read here, I downloaded the activesync from microsoft site, instaled it and plugged the cable to my pda. Nothing happened. Than I went to activesync connections enabled USB connection and tapped in connect. After a search, the pda was simply not found. Even after turning down de AntiVirus and Firewall, nothing happened.
What happened? I have to do something in the PDA? Couldn't find that info in here.
Thank's in advance for the help
Heurd
Does the LED in the speaker at the top change to orange?
Does the computer react at all? (any sounds etc.)
If not, try putting the device into bootloader: Press and hold the COMM button and then soft reset, and then plug it into your computer and see if anything at all happens.
If nothing happens, the USB cable is damaged. If the computer responds when the device is in bootloader but not when it is in, the ROM may not have the required software installed in it.
Hi,
Yes, the Led turns orange. I can charge the battery with that cable. But i also read that it's possible in some cases to charge but the part to syncronize can be damaged!!!
But what really intregues me is that I used that cable to put the ROM that I have. Supposedly it's a Qtek official ROM, i don't know if you can conclude something with this:
IPL 2.10.0001
SPL 2.20.0001
GSM 02.47.21
OS 2.20.7.29
In PDA appears the active sync icon and tapping it only appears a window that says to install AS in PC and connect. So I suppose that it has something.
thanks to l3v5y for the sugestion... I will try and than post here what happened.
does anyone has anymore suggestions... I will try everything to put this at work.
In PDA appears the active sync icon and tapping it only appears a window that says to install AS in PC and connect. So I suppose that it has something.
Click to expand...
Click to collapse
This seems to say you haven't successfully installed Active Sync. Try restarting your computer and seeing if it works then.
l3v5y said:
This seems to say you haven't successfully installed Active Sync. Try restarting your computer and seeing if it works then.
Click to expand...
Click to collapse
That is surelly not the problem because I installed AS 4.5, restarted the computer more than once, removed that and reinstalled and nothing... I even had put de AS 4.2 to try and see if it worked - nothing.
Now I'm not in my computer... I will try what you suggested when I go home.
I think it may be something to do with the USB cable...
Had that problem a while ago, my solution was to reinstall windows xp and it worked. so backup your pc, format your hard drive and then install the os (windows xp/vista). i guess it was usb-driver related.
REALLY
Unbelieveble...
well, It's easier to try in another pc before formatting mine. I'm not in the mood (too much time to put like I like)
That way I will check and see if my cable and ROM are allright.
Thanks for the tip croco_64
Hope to tomorrow come in here and wright that it's everything ok
Hi there!
Well... I've tried what you proposed. It is probably a problem of the cable. I tried with a cable of a digital camera and finally the computer detected the phone (with mine it only went orange light in the top, but never recognized - despite I changed the ROM with it ). However it gives an error - the instalation is not complete!!! I went to device manager in the PC and there was a yellow (!) in the windows mobile device.
Is it of the cable!? Do the cable have to have specific properties to sync the pda and the pc? The camera cable isn't enough?
yes... I had put activesync 4.5 in the PC!!!
thanks again for the help

Need urgent help plz...

Hi, I tried to get answer for my problems, but none any specific
so I`m startin a new thread...btw
My JASJAR has the same problem as lots of folks around here like it shuts off at any hard work like starting the camera or charge at 60%. I came to an end that as it works ok with the charger on, then the problem must be on battery. Well I'll try that
But the another problem is PC connectivity...it doesn't recognize the device
I tried MS Active Sync 4.1, 4.2, 4.5, windows 2000 SP4, xp SP2, different computer...just no luck, in bootloader mode it shows "serial" and "0.60" and whenever I plug in the USB, it shows USB, and then same, device not recognized...what to do?
And when I start the device, on blue background imate logo..it shows Radio 0.00.00, what does it mean..I can't even upgrade it as USB is not recognized...waiting for flash from SD, but no luck. Can any one sort these things out
First problem, almost definitively the battery.
Second and third problems could even be correlated, first the third problem/doubt, even if I'm not a complete expert, this means that your device was "unlocked" with the aid of a specific program that does just that (if you're interested in knowind how, go to the uni's wiki and read about unlocking), the Radio version 0.00.00 is just a "by-product" of that process.
So, if you're asking about this, you didn't do this by yourself, so you don't know what and how much has been done to your PDA, then for your second problem, first try a soft reset (this is always windows, remember it!), the re-connect the device (to the PC) and see what happens, then verify that you have the active sync program installed properly (and running) in your PDA, just when you connect the PDA to the computer, the active sync should become available as a running program, so, connect the PDA to the computer, the PDA turns on and says connecting, even if it does not connect to the computer you should see active sync running in your PDA, go to settings, system, memory, running programs and verify that it's there.
Another cause could be hardware (on your PDA), this means, cables and port or even internal (but this is quite unlikely).
Perform these tests and see what happens, then we'll see what else can be done.
Thnz, I trued several soft reset even hard reset,
I tried connecting to the computer with ActiveSync on, with some other software which changes the active sync connection to something like USB serial (from RNDIS ...), even advance networking off, taking out the SIM and memory card...running the device search..no luck.
and btw in computer after installing active sync it gives a window with all menu disabled except "File>Connection Setting". I tried by using bluetooth connectivity. No luck.
I read the thread about unlocking..and tried to do the rest..I mean the second step of unlocking, it showed device successfully unlocked..but all the same.
Any help....
mamaich method
Try this,
Step by Step :
get the tools at attachment , as mamaich told, you have to use it in bootloader mode , (Power + Light Bulb + Reset)
1. Stop Activesync USB connection
2. Uni : Reboot Bootloader then Connect USB
3. PC : Run mtty1.42.exe
4. Choose USB in "Port" (Reconnect if can't find/reconglize USB and try remove sim and sd card)
5. type : task 28 55aa
6. Press Enter
7. Cause DOC reformatted, so there's no rom in DOC ,try reflash any rom that you like .
For task 28 55aa in mtty success , will show the message (attachment )
DONE .

Unable to update ROM on HTC TouchHD

Hi all,
I have an HTC Touch HD (1.56). It was tied to Orange Poland, but I have SIM unlocked it with a web service. Now I wanted to try some different ROM (my main language is italian, but english would be fine as well -> as of now I've only been able to partially set language to italian changing registry code, but most of WM6.1 is still in polish). I have tried the HSPLWrapper_Blackstone_156OliNex.exe with no success.
If I just plug the HTC to PC USB cable, ActiveSync wakes up and connects.
I can browse inside, move files, install apps.
When I start the wrapper this is what happens:
1) with advanced USB settings ON (on HTC) the tricolour screen does NOT appear and the wrapper says Connection Error [202]. ActiveSync is ON and ready. -> if I start SSPL-Manual-TouchHD on HTC, the tricolour screen appears, the USB text appears, and on both wrapper and HTC I can see the progress bar at 0%. After a minute or so, the wrapper says there was a problem and shows the recovery procedure (I was never locked on tricolour screen, I just had to remove battery and everything was back to normal). If I try again the wrapper while the tricolour/USB screen is still there, nothing happens, and I get connection error.
2) with advanced USB settings OFF (on HTC) the tricolour screen DOES appear automatically when I start the wrapper, but no matter how fast I am pressing YES on HTC, the USB connection gets killed and ActiveSync disappears.
I have tried 2 different USB cables on different ports (no hub), rebooted PC several times. I have read the 3 wiki pages (HTC_Blackstone_Flash) and the OliNex procedure. What can I do? Can somebody please help me?
EDIT: I am trying this from Windows XP Pro up to par with WinUpdate (.NET 3.5 and everything else is there)
Thanks
You can always try USPL.
But first make sure you follow this exactly:
http://forum.xda-developers.com/showthread.php?t=505377
Hope it helps
A thread already exists for flashing difficulties. Please post your query within this thread
Ta
Rick

Categories

Resources