Related
I got a used wizard today,it is a few weeks old I also got a cradle with it.
I pluged in the cradle to the USB port and the charger to power, after playing with it for 1-2 hours I placed the wizard on the cradle to charge and after a few mins i noticed that it was over heating. I removed it from the cradle right away and noticed that the battery was droping 1% every minute or so. After it was down to 27% i removed the charger and left only the usb connection and placed the wizard on the cradle again. it was charging fine, when it was up to 90% removed it from the cradle and again was droping fast.
When it was down to around 25-30% of the battery I did a soft reset and since then I can never get it to start again also the red charging light does not show.
What the heck is wrong with it? I also get a light burning smell from the bottom of the wizard where the connector is located.
Any help?
I need your lights guys.
Don't like the sound of the light burning smell, that sounds like an electrical fault. It looks like your battery has died and the wizard battery setup is well known to do this. You need to plug it into the official mains charger (not the usb one) as this has an output of 1A, enough to kick start the wizard battery into life and start the charging. You need to wait a short while though before the light comes on. If this fails try to get a new battery and try that. Any more light burning smells and it needs to go back to the supplier.
I would suggest that you send it back to replace/repair. The rapid dropping of the battery power suggest that it is using power somewhere (illegally). I've heard cases of battery caught on fire, etc. and I won't suggest you to use it anymore until you sort out the 'burning' smell.
First of all thanks for your replys.
I pluged the charger on it and the red charging light came on after a while.
charged for over 6 hours and its still red? I think after been charged should change to green? right?
anyways after all that still doesnt want to turn on. I got it to start a couple of times but only to the point that shows the splash screen with the rom numbers and then it turns back off.
Should I give it a smash across the room on the wall? done that with some other things and worked just kiding.
Forgot to add that up to the point when i did the soft reset the device was working fine except the charge drop. Soft reset was done while it was working ( turned on)..... if thats any help.
i thinking u need flash phone with jafwm
and here u will find 3 flashs
www.gsm-support.info
fonec said:
i thinking u need flash phone with jafwm
and here u will find 3 flashs
www.gsm-support.info
Click to expand...
Click to collapse
That ain't gonna do jack sh1t to it. If it can't start to get into bootloader, it can't flash....and it's not a flash issue.
Usually the red light means power but not charging - happens to my qtek 9100 when I let it get too flat and I have to remove and insert the battery while the mains adaptor is attached - others have to 'jump start' the battery by directly connecting to a PSU - I wouldn't do this with yours.
From what you have said it sounds like a short somewhere. Any signs of water damage? Warranty? What Wizard do you have and what country are you in?
Richard
I got the wiza 200 O2 xda mini S from a guy in UK from ebay. The idiot sold me a cradle for it with an adaptor that says 12V on it (Like an idiot that I am i just noticed that) but then again how am I supposed to think that he gave me an adaptor that its not made for it when it says on the back of it "for Imate - Kjam". Do you guys think thats what burned the **** out of the unit ?
dont forget that some times turns on shows the ROMS numbers and turns off.
No water damage... I think its on warranty... I live in Greece.
Might not be the cradle - it could be it steps down internally to 5v. Use a meter and check what it outputs to the phone. Warranty with XDA's are 2 years to the *original* purchaser. As they are only supplied with an airtime agreement then that isn't you.
Richard
have you tried changing batteries to a new one? Seriously, thats the easiest thing you could do right now and you could actually get results.
Ok this is what I did.
Removed the baterry from the device,
got a 12V 1 Amp power supply that I had lying around and give it a few shots connecting it to the battery giving it an electro shock.
(If you're going to try this be very carefull.<<<< DONT LEAVE the power supply connected to the battery>>>> just give it a few shots 1 second on and off.
That was it.
It started working, device turned on and now its charging (I think) yellow light is on.
I'm going to leave it on for a few hours and see what happens.
Wish me good luck. I'll let you know soon.
ok... this is what happend.
Battery is drained and its not charging due to a blown fust on the main board.
I open the phone and placed and solder a little wire over the fuse.
Still does not charge. ^%$#%$#$^%$*
Before I replaced the fuse or should i say short it the yellow light would come on for a few min and then red again. Now when I charge the battery with another external power supply the pda comes on for a few mins and then dies again. ( no charging light whatsoever).
Does anyone know where to get a mainboard for it and about how much it costs?
Asking for help again.
SmartMan said:
ok... this is what happend.
Battery is drained and its not charging due to a blown fust on the main board.
I open the phone and placed and solder a little wire over the fuse.
Still does not charge. ^%$#%$#$^%$*
Before I replaced the fuse or should i say short it the yellow light would come on for a few min and then red again. Now when I charge the battery with another external power supply the pda comes on for a few mins and then dies again. ( no charging light whatsoever).
Does anyone know where to get a mainboard for it and about how much it costs?
Asking for help again.
Click to expand...
Click to collapse
Hey man, sorry to hear about that.
The best you can do is to claim your money from ebay.
You probably killed it when you pluged in the 12V PSU. That's 230% of the normal Volts! Otherwise sell it for parts.
I'm in the process of claiming the money back from the IDIOT that sold it to me.
Lets see if that part of Ebay works as good.
SmartMan said:
I'm in the process of claiming the money back from the IDIOT that sold it to me.
Lets see if that part of Ebay works as good.
Click to expand...
Click to collapse
Doubt it. Did you ask the seller for help before opening the phone and voiding the original warranty on the device?
SmartMan said:
ok... this is what happend.
I open the phone and placed and solder a little wire over the fuse.
Click to expand...
Click to collapse
Not a good idea IMO as now the blame is on you as previously he may have been able to get warranty service from the original vendor.
Richard
I did ask.
He is not the original buyer.
what was I suposed to do.... track back 2-3 buyers to find the original... send it to him so he can have it repaired? Anyway it was out of warranty because of the burned fuse that says that some other charger was used with it.
I had a similar thing happen but fortunately not as bad as yours. Twice now my battery has mysteriously drained completely. The last time when I tried to turn the unit on, it flashed the boot screen for a couple of seconds then poof, no more juice. When I plugged it into the USB port, nothing, no lights, no charge, no recognition from Activesync, I thought the unit was fried. I use Tmobile and got to admit they did send me a replacement fairly quickly. Before I packed up my unit I thought maybe I should plug it in using the wall charger and presto, it came on and is working fine. I have no idea what causes this but do know that if the battery is completely discharged the USB port can not over come this to put a charge on.
Same thing happened to me, kind of strange though. The charge was perhaps 70% to the best of my knowledge. I flashed it with Mr. Clean ROM and booted it up.. it came in fine into WM5, then it started the installation of the 3 progs or whatever comes with Mr. Clean.. after the second finished the unit just died *poff*. Screen blank, no responce to power buttons or any other buttons for that matter.
I've tried taking out the battery for different intervals of time, no luck. I've tried using the AC charger, no luck. No lights, sounds, telepathy or matrix ****.. it just lies there like a dummy phone.. hmm what to do. Bought it from a guy in UK (im in sweden) on eBay, don't think I will have much luck there.. even though it's brand new...
Any thouhgts?
I have had this problem - I bought a replacement battery and all is now fine. Another thread in this group states that the battery cannot charge without the OS up - so if the battery is completely discharged then it is impossible to charge through the phone. The only solution seems to be somehow to charge the battery directly - as appears to have been done earlier in this thread.
Chris
p.s. if anyone knows of another way to do it I'd be interested to hear as I'd like to revive my old battery and keep it as a spare
Hi there,
First I apologize about my poor English, I am Brazilian and should speak portuguese, but this is the best forum ever... so I'll try my English
My story:
Four days ago my 1,5 years old 9100 running the WM6 NTS was working perfectly, the best device I ever had. But, at night, I removed the battery to get the SIM card and then I put the battery back but did not turn on the phone. I used the SIM card in another phone during the night. I was afraid to lost it.
In the morning, I removed the battery again, put back the SIM card and then the battery. When I tried to turn it on, nothing happened, just like as if it was without any power. I was surprised, because I had fully charged the battery in the night before and before I first remove the battery, it was about 80% of power. So, I decided to try to recharge again, but there was no lights on. I left it charging for about 10 minutes and got nothing.
So, as I was leaving home, I put the 9100 in my pocket, after a few minutes I tried to turn it on again and it worked. The battery meter was showing about 80%.
Ok then… It worked well on Monday. But when I woke up yesterday morning (Tuesday), the phone seemed to have self-restarted during the night. So, I typed my password and it started working well again. I checked the battery meter and it was showing about 40% of charge. After a few minutes the phone seems to be totally dead. I tried to charge it again and after 2 hours I got nothing, it was still dead, did not turn on and there were no lights on.
Later on that day, I got a multi-meter and checked the battery tension. With the positive on my left I could check that measuring the power with the wires on the 1st “slot” and on the 3rd on, I get 3.47V. Measuring the 1st with the 4th I get 3.63V and measuring the 1st with the 5th or 6th I get 3.75V. Check what I mean at http://webtennis.rg3.com.br/qtek_9100/battery.gif.
I tried to remove the battery, then put it back and then turn it on again… It started, but in a few seconds, when was showing the OS, SPL, etc… it went off. I tried that again; it started, loaded the OS and went off. Once again I tried this, but with the power cable on, so it started but in seconds was off again.
So I thought “that might be a bug, maybe if I run the update utility it will work”. I started the phone in the bootloader mode, but before I connect the USB cable and start the RUU the 9100 went off. A few more times tring to remove the battery and starting it again, it went off and never came back again!!
I plugged the power cable on the wall and on the phone and there were no lights on, but I could feel the battery a bit warmer, just like it used to get. I left on the wall all night long and today in the morning still nothing. I removed the battery for about 30 minutes and got nothing, neither the screen with the OS, SPL, IPL…
Now I am despaired, don’t know what to do, no clues. I am in Brazil and don’t know where I can take to be repaired and have no plans to get back to Canada or Europe for the next 3 months.
Can you help me with this problem? I love my phone and want it working again.
Thanks for all your help.
Battery problem...?
It seems as thought you may be having a problem with your battery, not your phone. Try buying a battery off eBay, they are pretty cheap, and that should tell you what the problem actually is.
Or if you know anyone that has a wizard, try your battery in their device. If the problem is still appearing, then you will know that you just need a new battery.
Battery or charger ?
I agree with zakhir_n, it sounds like a battery issue not the phone. My friends MDA battery died after 2 months of use, so you can never be sure. We swapped batteries and revealed it was his battery not taking a charge.
Next check that you are using the original charger. I went away on business and grabbed the nearest charger for my 8125. Needless to say I grabbed a Motorola charger and it refused to charge the dead battery. Make sure you have the original charger, as it MUST say 1000ma or 1Amp output on the plug. The Motorola one I used was only 500ma or .5Amp and it was unable to recharge a dead 8125 (MDA) battery.
New status: WORKING
Hi there,
Thanks for all the posts.
Well, I checked my charger and it is a 1A 5V and my battery gets 100% of charge.
This is what I did:
Fully charged the battery, removed it for about 1 day an then I turned it on. Surprise!!! It was working and worked for 20 minutes and went off again e seemed to be dead.
Once more I the same thing but this time I flashed it with an official ROM. Fully charged the battery and removed for about 1 day. When I tried to turn it on, it worked as it was new.
So I flashed it with the WM6 Core 2.0n. It worked perfectly. When the battery got 80% of power, it restarted itself for several tines.
Now I bought a new battery and it is working very well, no problems till now. Guess you were right… I really had to change the battery.
Thanks for all the help and sorry about my English!!!
Regards,
Arthur
Nooooooooooooooooooooo
Hi there… Got the worst birthday present ever!!! Today I woke up and my QTek 9100 wasn’t working.
I got a new battery, when I put it on my phone it was 54% of charge. I used it till it gets 13%, then I fully charged it with my computer’s USB cable. Used the phone for 1 day and the battery was again around 80% of charge (just like the other time). I put it on “flight mode” went to sleep. When I woke up……. it was not working anymore, I put back the old battery and got nothing.
Now it is with the new battery being charged with my wall charger (1A 5V), but there is no lights on.
I already tried to run the WM5, tried a new WM6, checked the charger, replaced the battery and none of this seems to solve my problem… Do you know what more I could try? Do you know where I can send it to fix in Brazil?
I don’t know what to do… I already sent e-mails to QTek and to HTC and after 1 week got no answer…
Thanks for all the help!!!
2 days ago i had my cingular 8125 plugged into a charger . when i woke up it was off and dead, still plugged in?
now when i plug it in (to the stock charger) the red light comes on, but if i take the battery out, it stays on. if the battery is in, it is on. but i cant turn it on. ive left it for 15 hours now, and still nothing
even tried another battery.
when i first put the other battery in it turned on, was booting, but then died. probably cuz the battery was dead. but i had it plugged in as soon as i turned it on.
now the same thing happens.
any ideas?
i also thought i smelled something burnt. like if you have ever had a laptop that had a bad a/c connector and would heat up a bit, or even smoke!
dont know if it was my imagination or what?
thanks in advance
dan
T mobile MDA shows RED LED
that is strange that you post this today, because I just received T-mobile MDA unit from 3bay that has a similar problem.
-The phone does not turn on when I press the power button.
-It does not respond to a soft reset or a hard reset.
-With the battery in, I connect the AC charger to the phone and for about 1-3 seconds the charging LED color is RED. THe LED turns off and I can not get the same result if I reconnect the AC charger.
The only visible sign of life this MDA unit has is:
-with the battery out and the AC charger connected, when the USB is removed to the point where it is not connected to the MDA, the charging LED light flashes red for a split second and the screen flashes white for a split second as well. [I hope this is a sign that there's still life in this MDA, but i'm thinking my unit is truly a brick..]
From all the websites I've searched, this does not seem to be an issue, although for me it is a scary one! Anybody that can help would be much appreciated because I want a working MDA not a dead one
EDIT: It turns out my non-booting MDA was due to a faulty vibrator and flashlight MDA part. After removing these two pieces that are connected to the back cover of the MDA housing, the MDA booted up with no problem.
danrw84 said:
2 days ago i had my cingular 8125 plugged into a charger . when i woke up it was off and dead, still plugged in?
Click to expand...
Click to collapse
I'm in exactly the same position - left phone on charge overnight two days ago and in the morning it was completely dead. I have managed to get it to power on for about 2-3 seconds on one or two occasions but now it won't do a thing
Not sure if this will help, but have you tried to push that soft reset button that you have to to push with your stylus when it is plugged in?
Sounds stupid, but my power button is completely dead and I thats how I have to start mine up. I also have to pop out the SD card to get the screen to come out of sleep mode!
I might not work, but hey...worth a try.
Well, I eventually got back up and running. Turns out the battery was completely dead. I used the 9v battery trick and then used my USB charger to get the battery fully charged and all is well.
This leads me to query how do I now charge my phone when I don't have access to a PC? I was using a standard AC wall charger and the phone showed that it was charging but due to the fact that the display stays lit whilst on external power, this eventually killed the battery as the charge indicator appeared to be false.
*as posted verbatim in another thread*
WHAT IS THIS 9 VOLT TRICK YOU SPEAK OF?!?
funny...i'm having the same problem with 2, what were perfectly fine, wizards.
which is what brought me to this forum post.
These two devices were turned off and sat in my desk for months as they were not needed. They were perfectly good, successfully unlocked and upgraded from the advice/steps/tools provided here (thanks!). They were my primary personal and work devices until i was given the option to try a few iPAQs.
Now that I want to go back NEITHER device will boot. On the original chargers (both wall and usb) both devices will display the red light as shown in the pic above, will not boot normally, or via the 2 or 3 button methods common for these devices. The batteries do not get warm, which tells me that they are not getting current...which makes NO sense if i'm using 4 different stock charging options (2 wall and 2 usb) in different locations. One expect some variable would work to eliminate some oddity, but nothing is working.
something odd is going here. how can 2 perfectly good devices and charges suddenly crapout? I could really believe it's the battery, but one is grand spankin new (only used for a month)! Both have the main board die? Both not recognizable on any computer?
Is it possible that the backup battery is causing this? Can it me charged same as the standard if its drained? I know i'm grasping at straws here, but this odd a coincidence.
FOUND FIX
okay..this was too simple.
for some reason the USB will not provide enough"juice" to pop these out of their sleep.
I have been using this great little charging system made by good old Radio Shack that is a single plug with different adapters for all different devices...i've been using it for my iPAQ's, Blackjacks, BB's, ect. SO as a last resort i went and got the CORRECT adapter (as there are many mini usb adapters available) and SHAZAM!!! they boot right up!
don't ask me why the stock wall chargers will not work, but these RS iGo systems are the trick!
i'm going to link to the other similar issue in hopes any other folks having the same issue can benefit from this.
Hello,
I've a Wizard that is approximately 20 months old. Yesterday, before I went to bed, I set the alarm clock on the Wizard, put it next to bed and went to sleep.
This morning upon waking up I tried to switch on the Wizard but it couldn't. Firstly, I thought the battery was discharged, so I tried charging through USB on my computer -- it wouldn't charge or start. Then, I tried charging on the default charger -- again nothing.
I tried removing battery and soft reset - nothing. It's really weird, yesterday I left it working, no-one has touched it and today it's totally non-responsive.
Any ideas what might be wrong/how can I bring it back to life? Would a hard-reset help?
Regards,
1. how much charge was in the battery last night?
2. is your battery 20 months old also?
3. do you have a spare battery to try?
4. do you have many applications, music etc. on the device?
1. how much charge was in the battery last night?
Click to expand...
Click to collapse
Unfortunately I can't remember, however I have an alarm which sounds periodically when the battery is below 20%, so I'm guessing I had at least 20 percent. Could be wrong, of course, but most likely above 20%.
2. is your battery 20 months old also?
Click to expand...
Click to collapse
Yes, this is the original battery. Aprx. 20 months old.
3. do you have a spare battery to try?
Click to expand...
Click to collapse
I don't have that. I guess I could go to mobile phone service shack and check there. Do you think it's the battery?
4. do you have many applications, music etc. on the device?
Click to expand...
Click to collapse
The Wizard came with a 64MB card I think. I had around 10MB free space. 3-4 applications, 2-3 mp3s. Nothing unusual.
Same thing (sort of) happened to mine after about 187 months. I was using mine and it hung up. I hit the reset button and that was the end of that. Even when plugged in it does nothing. Tried a hard reset... nothing. Soft reset.... nothing. Dead. Zip. Nadda.
Good news? Replaced it with a Kaiser!
vivanov said:
Hello,
I've a Wizard that is approximately 20 months old. Yesterday, before I went to bed, I set the alarm clock on the Wizard, put it next to bed and went to sleep.
This morning upon waking up I tried to switch on the Wizard but it couldn't. Firstly, I thought the battery was discharged, so I tried charging through USB on my computer -- it wouldn't charge or start. Then, I tried charging on the default charger -- again nothing.
I tried removing battery and soft reset - nothing. It's really weird, yesterday I left it working, no-one has touched it and today it's totally non-responsive.
Any ideas what might be wrong/how can I bring it back to life? Would a hard-reset help?
Regards,
Click to expand...
Click to collapse
Mine died too when i was flashing...
Leave the phone in the original charger for a while and see if it picks up...sometimes it comes back to life by doing that...
If that doesnt work, try a new battery, you might be lucky...
A somewhat strange development occurred today:
Today (3 days after it stopping working) I randomly tried to switch the Wizard on and it indeed switched on. It showed that it had 0% battery. It didn't even show 0%, basically the battery charge graph was empty - no number, no fill, nothing.
While it was on charge the charge light was on (while it was 'broken' the charge light was off when I tried to charge). So I left it to charge and when I checked back in 15 minutes it was back to being 'dead'. Can't be started, no charge light, nada.
I don't really know what's going on, however I'm highly suspicious of the battery. Currently, I'm periodically trying to switch it on again so I can backup my data.
Any ideas what might be wrong with it, do you think it's the battery or is it more serious?
Regards,
The battery won't charge if it gets to low.
There is a thread about using a 9V battery to get the battery up to a level so it will charge. I don't have the link for it, try searching for it or maybe someone else will reply.
You might have a bad battery. I bought a new battery because I didn't think I was getting the life that I should. I tried using the old battery about a month after when I had to run out and my main was low. About 15 minuets later my phone started shutting of and rebooting. That was the end of that battery.
Yep, it's possible. If the battery is to empty, you can't charge the phone. It is stupid but it's just like that. You also can't power on the phone without a battery with the charger connected.
Yesterday I received my wizard and I had to revive my battery too because it was completely empty. I used a self made 5V power supply and after 2 minutes charging I placed the battery in the wizard and was able to charge and boot with the charger connected.
Here's the 9v battery trick, connect the + from the 9v battery to the + of the phones battery and the - to the -, hold there for only 10 seconds then remove the connection for 10 seconds and then repeat the process about 8 to 10 times and then put the battery back in the phone and connect it to the wall charger to fully charge.
Thanks for the advice. I'm going to do the jump-start thing.
However, I've hard time determining which is the - and which is the + pin layout on the battery, since the label is not correctly applied.
As far as I can see the - is the one at the far right, however I'm not sure which is the + pin.
Can someone help me with this, please?
Regards,
vivanov said:
Thanks for the advice. I'm going to do the jump-start thing.
However, I've hard time determining which is the - and which is the + pin layout on the battery, since the label is not correctly applied.
As far as I can see the - is the one at the far right, however I'm not sure which is the + pin.
Can someone help me with this, please?
Regards,
Click to expand...
Click to collapse
When you take out the battery and put it back in that direction ,turn and face up the connector side fasing you,the first connector from the rightside of the battery is the ' + ' and the last is ' - ' towards the leftside.Be careful while connecting and try not to touch other connectors. Don't keep the connections longer then 10 seconds interval.
good luck
Xeno1,
My MDA battery also died and went below re-chargeable state. Your trick to use 9volt battery to jump-start it worked just fine for me. I connnected for about 20 seconds (2x times) and plugged it back into phone and connected USB cable to it and my nice yellow charging light came back on. After about 30 mins, I could use the phone.
THANKS FOR THE GREAT TIP!!!
easier fix, take a standard usb cable. rip off the smaller end with a wire cutter, expose the red and black wire. take out your battery, than connect the negative(black) wire to the negative end of the battery, than the red wire to the positive end of the battery, leave it in there for exactly 3-5 minutes for jump start. after that turn your wizard on, and quickly shove it inside a new usb cable. or the wall charger.
note:
if not done correctly, you may damage your wizard or the battery. if theres a power overload or your power goes out. your wizard will burn out!
feedback is greatly appreciated.
p.s after that my battery seem to be weak, charge barely holds for 12 hours. after 12-14 hours it will die out. so i suggest buying a new battery after couple of days.
Thanks guys! Vario died yesterday and wouldn't turn on or charge.
Tried the 9v battery recommended here and it worked! I was a little unsure which end was - and which was + but using the advise above, got it right. Wasn't too worried as found and ordered a replacement from ebay this morning for £7.
The first connector on the right hand side, nearest the end of the battery is the + the one more towards the middle and further away from its corresponding end is -, or at least, thats what worked for me.
Thanks again!
Experiencing the same issues after I set aside my Mini S as it was experiencing problems with regards to its screen alignment. Wasn't able to charge it during that time I kept in the drawer unused - due to frustration as I can't use it anymore. After downloading a guide to disassmble it so I could remedy the problem I found out that it won't power up anymore even with a new battery.
Well, haven't tried the jumpstart thing and the original battery was disposed of already to try the jumpstart idea. Could it be the internal battery is causing the problems? I opened my unit up and tested the internal battery for power and it registers a measly .2V left. Will use the 9V thing to power it up (as been doing that before on watch batteries that are hard to find replacements) before I do it on the main battery. Here's hoping it works as the Mini S has been quite useful for me until now.
UPDATE: I charged the internal battery and it now reads 1+ V and the external battery at 3+ V. No luck yet though as the unit still won't show any life. Any suggestions?
Vivanov, I know it's been a few years now, but did you end up fixing your problem? If so, how?
hey, i got the leo just over two weeks ago, and swapped my orange sim for my o2 sim (my phone is unlocked) yesterday night. This morning the phone did not charge at all and i still cannot get it to charge, i have tried via the wall plug and plugging into my PC. At the top of the phone there is a green LED flash and then an orange one.
Any ideas as to why it wont charge, im still under guarentee so if its any problems with the battery etc. i am sure i can get it replaced, Thanks in advance.
i've tried taking out the SIM then turned it on and off, that didn't work. I then tried the same but with the SanDisk card. Still no hope.
Hi, sorry to here about your troubles but it is nothing I haven't seen before. Hope this helps.
http://forum.xda-developers.com/showthread.php?t=610330
Try to release all the energy of the battery, then plug the usb cable to computer, us your PC to charge it.If it dosen't work, congrats then, you are in the same situation as me,
-order a new battery replacement see if it's sloved, if not, send it to HTC for repair.
btw, just curious, are you in Canada as well...?
hi i have the same problem solution is simple you just bend middle pin that connect battery bend it down a little and it should works
Thanks mmpl, I am gonna try that, I wish that may solve my battery drain problem as well.
nah im not Canadian, from the UK. The place i bought it from said i could send it to them and they can check it, if they can't fix it they'll send a new one to me
WOW! amazingly, i had no hope in it. But i did play around with the middle pin just a slight tap backwards and then *forced* the usb into my phone and computer, it switched on switched off i unplugged my phone is did a white screen flash, but it is now holding the solid orange LED of life! i can't understand what on earth was wrong, and it could still not charge but the LED seems to be correct!
Unfortunately i am now experiencing this with a replacement battery from China. It flashes green and orange when plugged in and won't charge. Original battery works normal. Well... back to seller.
Problem Fixed!
Thanks mmpl. The middle prong on the HD2 that connects the battery was pointing slightly up from horizontal (and it looks different than the two prongs and seems a little limp/loose); I pushed it down a little so it's just slightly down from horizontal; put the battery in and that fixed it! Thank you for posting the solution!!!
My symptoms were that the battery indicator icon in the title bar would switch to full bars when plugged in (did not show the plug icon in the title bar as it should have), but when I click on the battery indicator icon the sub screen (showing the battery) would show the actual state of the battery, e.g., 30% with one bar.
I've been also having freeze-up problems when dialing out, thereby requiring a re-boot (take the battery out or push the reset pin) once or twice every day (I'm on the phone a lot however), and maybe the daily removal/re-install of the battery weakened the prong.
Replacement battery from China...
ahdai said:
Unfortunately i am now experiencing this with a replacement battery from China. It flashes green and orange when plugged in and won't charge. Original battery works normal. Well... back to seller.
Click to expand...
Click to collapse
Hi, I also have purchased a cheap replacement battery from China as a backup for my Samsung i500. I cannot charge this battery in the phone! I get a pop window when I connect my charging cable that states; "battery is not connected"! The stock original Samsung OEM battery charges in the phone just fine.
I wonder what the problem is?
mmpl said:
hi i have the same problem solution is simple you just bend middle pin that connect battery bend it down a little and it should works
Click to expand...
Click to collapse
Thanks mmpl, I had not even considered the pin until I read your post.
I know this is the wrong thread for xperia ray, but I just wanted to say that this is something that could happen to absolutely every phone. The middle pin on my ray was stuck in, so far in that it would not connect properly to the battery. By getting a sewing needle in and tinkering it back out it now connects and charges properly.
Also, I hear that if you have flashed your phone you may need to re-calibrate it. If your phone is rooted, you can do this with the aptly named app called BatteryCalibration. Worth considering I think.