U can check if u have this problem and see the resolution by visiting this link:
http://forum.palmislife.com/viewthread.php?tid=69825&highlight=
Enjoy it
ASZ
looks like a fairly complicated procedure
This is nothing new and has been covered previously in this forum. Check the Wiki, and you'll find a very simple and painless solution to the screen alignment problem...
goestoeleven said:
This is nothing new and has been covered previously in this forum. Check the Wiki, and you'll find a very simple and painless solution to the screen alignment problem...
Click to expand...
Click to collapse
Yep, that's right and also keep in mind that there is NO solution that has worked for everybody. It is hit or miss, lots of folks use the business card method - didn't work for me. I took mine apart but it took several attempts to adjust things just right. (And others have said theirs ended up in a worse state, one I saw even ended up with the screen so far out of alignment it refused to align at all!!
If it's under warranty send it back
Mike
Related
Don't know if this has been posted yet or not (I went 3 pages back and saw nothing) but the problem with the screen alignment is that there is a sponge pressing against the digitizer.
You'll have to open your device and remove this sponge strip and the screen alignment issue will be gone.
If you have warranty on your device, it is suggested that you get it repaired through your warrant, but if your a DIY person, then go ahead and do it (opening your device will void yoru warranty).
Since i don't have a TyTn myself, i can't do a step by step guide but check this link out, there are some pictures of the process.
If this process indeed fixed the issue, then it's good to know!
Anyone here has tried it ?
I am still waiting my MDA Vario II !
Caution
gogol said:
If this process indeed fixed the issue, then it's good to know!
Anyone here has tried it ?
I am still waiting my MDA Vario II !
Click to expand...
Click to collapse
I have posted elsewhere on this board my solution - which is similar but whilst I removed the gasket I replaced it with a thicker one and firmed up the retaining clips on back of screen. Mine is still fine, but there is a lot of trial and error involved with these solutions. One site I saw was similar to the solution above - a japanese site where he found just taking out the original seal and not replacing it with anything made the problem even worse!
To be honest my personal view is (even though I did my own fix) is get it fixed/replaced under warranty. Slack keyboard maybe a different matter as the fix is rather more certain, but again if you dismantle a device to fix a slack keyboard and you did not have an alignment problem - beware the dismantling may create an alignment problem!!
Mike
What is the fix for a slack keyboard? At least half of my keys don't register after the "click".
Keyboard
rrentrop said:
What is the fix for a slack keyboard? At least half of my keys don't register after the "click".
Click to expand...
Click to collapse
Sorry when I say slack keyboard I'm not refering to the missing keys or hard press issues but to the loose sliding and clicking into place mechanism of the keyboard.
Mike
When it's cold it usually works.
but after a while it just works less and less until finally it's not working @ all.
I've returned it twice now. They just send it back after having supposedly replaced the screen. But i have my doubts.
Now I'm going to have to return it for a 3rd time. I have more than one of these phones and I do love them. This one however is just crap.
Apparently vodafone hasn't got a clue. Maybe I can give them some instructions on what to do with the damn thing. What would you tell them in my place?
I've had the thing for a few months now but it hasn't worked properly @ all during this period.
I even created a lovely video to show vodafone my problem
http://www.youtube.com/watch?v=wpQyH3i7RQk
http://waalre.pwnz.it/tytn.avi
(might not work immediately because I only just uploaded it to the site)
p.s. thanks and keep up all the good work
yfniyfni said:
When it's cold it usually works.
but after a while it just works less and less until finally it's not working @ all.
I've returned it twice now. They just send it back after having supposedly replaced the screen. But i have my doubts.
Now I'm going to have to return it for a 3rd time. I have more than one of these phones and I do love them. This one however is just crap.
Apparently vodafone hasn't got a clue. Maybe I can give them some instructions on what to do with the damn thing. What would you tell them in my place?
I've had the thing for a few months now but it hasn't worked properly @ all during this period.
I even created a lovely video to show vodafone my problem
http://www.youtube.com/watch?v=wpQyH3i7RQk
http://waalre.pwnz.it/tytn.avi
(might not work immediately because I only just uploaded it to the site)
p.s. thanks and keep up all the good work
Click to expand...
Click to collapse
First welcome to XDA-Dev
You don't know it b ut the problem has been reported here umpteen times. If you use the Search Google Sticky post near the top of the messages postings you will usually find what you are looking for.
There are recent threads on this probably not more than one page back!
Regarding the servicing. Actually I can believe they have replaced the screen. BUT we here probably know more than they on some matters. We know that this problem is not caused by a faulty screen - it is not the more traditional Screen Alignment problem (though it is related to it). We also know that to test this after any servicing is done, you need to leave the device on using power hungry apps to warm the device up.
I always recommend anyone with a warranty to insist on a Replacement and NOT a repair for this problem. There is an interesting recent thread taht suggest slackening casing screws and even internal screws can alleviate the pressure causing the problem. BUT if you have a warranty get another device - new screens are NOT the answer.
Here as a welcome is a saved version of my search. Please use an existing thread if you wish to post on this matter.
http://www.google.com/search?as_q=p...rum.xda-developers.com&as_rights=&safe=images
Cheers
Mike
Hi there, my phones screen will not work, my friend kept opening and closing they keypad quickly after which he gave me the phone back and the screen did not work!
The problem im having is that the touch screen dont work, nothin else is wrong, the screen is not cracked, jus that it dont touch sceen no more.
The bad thing is I put it on boot mode and erased the phone memory, and since the touch screen dont work i can allign the cross thing.
Does anyone know a way in which i could fix this?
Cheers.
pod8 said:
Hi there, my phones screen will not work, my friend kept opening and closing they keypad quickly after which he gave me the phone back and the screen did not work!
The problem im having is that the touch screen dont work, nothin else is wrong, the screen is not cracked, jus that it dont touch sceen no more.
The bad thing is I put it on boot mode and erased the phone memory, and since the touch screen dont work i can allign the cross thing.
Does anyone know a way in which i could fix this?
Cheers.
Click to expand...
Click to collapse
Mmmm. Tricky perhaps. A hard reset will either cure or leave you stuck. If you hard reset and the screen is indeed dead (touch wise) then you'll never get past the alignment stage. If the touch issue is software related then you would be sorted with the hard reset.
A gamble I think!!
However you are stuck at the moment so in a sense you have nothing to lose. If it ends up being useless then you are faced with a warranty (hopefully) repair otherwise some DIY though it's not entirely obvious what has broken/come loose - possibly just a ribbon connector.
Mike
Maybe the ribbon cable came loose on the LCD side?
myztikal47 said:
Maybe the ribbon cable came loose on the LCD side?
Click to expand...
Click to collapse
Yeah i think its that as well, i hard reseted it a few times with no effect, in the begining of the day, it could still reconise the screen taps around 2/3 times before it totally went dead.
Are there any tutorials on how to open it up to check the ribbon?
Thanks.
This maybe the hardware problem with the mainboard itself. I read about this on here a few times, most people had the get their phones exchange....
myztikal47 said:
This maybe the hardware problem with the mainboard itself. I read about this on here a few times, most people had the get their phones exchange....
Click to expand...
Click to collapse
Yes, I am equally unsure that this is just a simple loose connector. It may be, but it appears to be fine for a short while and only then goes off.
Like you myztikal47, I suggest going for warranty replacement if at all possible. Only if you have no warranty shuld you attempt a repair yourself - this is a notoriously ellusive fix and indeed I would say there is no 100% works for all answer. Certainly do not assume it's the screen - most probably it isn't and you'll waste your money.
There are dismantling links in this forum - but you'll find them on my small Hermes site http://michael-channon.spaces.live.com- go to the loose keyboard section and you'll see the links.
Mike
my 8525 had the same exact problem, and i swapped the LCD and still doess the same thing...
I dont know what the problem could be, and i dont have a warranty.
What could be going on????
Any 1 know where 2 find the service manual????
Jorge
[email protected]
mikechannon said:
Yes, I am equally unsure that this is just a simple loose connector. It may be, but it appears to be fine for a short while and only then goes off.
Like you myztikal47, I suggest going for warranty replacement if at all possible. Only if you have no warranty shuld you attempt a repair yourself - this is a notoriously ellusive fix and indeed I would say there is no 100% works for all answer. Certainly do not assume it's the screen - most probably it isn't and you'll waste your money.
There are dismantling links in this forum - but you'll find them on my small Hermes site http://michael-channon.spaces.live.com- go to the loose keyboard section and you'll see the links.
Mike
Click to expand...
Click to collapse
Ok my best bet is to take it to carphone, i got my screen replaced there a few months ago, think i still have a 1 year warrenty
Thanks for all your help anyways
Tytn Service manual
jblandon1024 said:
my 8525 had the same exact problem, and i swapped the LCD and still doess the same thing...
I dont know what the problem could be, and i dont have a warranty.
What could be going on????
Any 1 know where 2 find the service manual????
Jorge
[email protected]
Click to expand...
Click to collapse
Here you can found the manual
http://www.megaupload.com/?d=0GD472TP
Roby
Aaaaghh. I am on a trip overseas and the backlight of the LCD screen on my Dopod 838 Pro just went out. Under a bright light I can make out the screen changing as things happen, but it kind of makes it hard to read (impossible!!). Luckily TomTom kept talking to me, although not as good without the picture of the map to follow!!
Anyone heard of this before? Have read of a few "white screens", but this seems different to other posts.
Would appreciate any tips on fixing or replacing the screen. I plan to try to pull the machine apart and make sure a connector hasn't come loose when I get home, but am hoping I am not up for a new machine just yet.
Although this may be an excuse to upgrade to the Touch HD when it available in Australia!!
Thanks in advance.
3 things
try 1st
make sure your brightness is turned up, settings/system/backlight
try 2nd
backup device, hard reset, see if this works. ( the backlight should not be a software issue, but it is possible)
try 3rd (although I would try this 2nd if you can, because if this works will not lose your personal data like you will in step 2)
take apart and check the flex, (common cause of this problem)
Thanks, time to find my torx screwdrivers!!
Have been playing with as many settings as I could see with a bright torch, and then tried a hard reset (fortunately it was still able to connect to my PC for backing up data).
Even loaded a new ROM OS.
It happened to my Jasjam and I found the scroll wheel circuit board was the culprit (don't ask me how). I managed to get a "broken" Jasjam off ebay for a fair price and cannabalized it for the part I needed. Fixed it nicely.
I don't know if your is the same thing but if you can get a hold of a "broken" Hermes it might be worth a shot. Found the "broken" Jasjam had nothing wrong with it either. Good buy for $120AUD...
Cheers...
ultramag69 said:
It happened to my Jasjam and I found the scroll wheel circuit board was the culprit (don't ask me how). I managed to get a "broken" Jasjam off ebay for a fair price and cannabalized it for the part I needed. Fixed it nicely.
I don't know if your is the same thing but if you can get a hold of a "broken" Hermes it might be worth a shot. Found the "broken" Jasjam had nothing wrong with it either. Good buy for $120AUD...
Cheers...
Click to expand...
Click to collapse
Oh thanks heaps man I just fixed my JasJam backlight problem by replacing the scroll wheel circuit with another one!!! This was definately the issue, i would have never thought of trying this! This should be added to the wiki.
afaast said:
Oh thanks heaps man I just fixed my JasJam backlight problem by replacing the scroll wheel circuit with another one!!! This was definately the issue, i would have never thought of trying this! This should be added to the wiki.
Click to expand...
Click to collapse
how exacly to do that, i have a backlight problem to please help
backlight only turned on when i slide my hermes
http://www.youtube.com/watch?v=N8MmIErLhag
and my 2 videos showing the same problem.
http://www.youtube.com/watch?v=MVgFCV3boX4
http://www.youtube.com/watch?v=cFZhWS5jEik
Weird! Mine doesn't have this issue, I've tried the Notes line drawing test.
Neither do I..
Go get a replacement, it might be a faulty device. Not sure what's the point here. It is not a problem with the device, it's a problem with YOUR device.
To be fair mine did do it every once in a while, thought it was perhaps sumthing I had on my finger (oil/grease/water/sweat whatnot) however, desensitised the screen and popped a screen protector on it and it's 100% reliable now..
The first video is not mine so it is NOT my device problem and i tested on another hd2 and it made the same thing. That's why i came up with the touchscreen tweak you find on the tips and tweaks sticky but even that do not solve it 100%.
It has been confirmed has software problem like the pink camera here.
http://wmpoweruser.com/?p=10735
and original post
http://translate.google.pt/translat...htc.ru/2009/11/u-htc-hd2-eshhe-odna-problema/
the_ape said:
To be fair mine did do it every once in a while, thought it was perhaps sumthing I had on my finger (oil/grease/water/sweat whatnot) however, desensitised the screen and popped a screen protector on it and it's 100% reliable now..
Click to expand...
Click to collapse
that was my exact thought but with a screen protector i could make it do that so i quitted on it at the end.
Good to know i'm not alone here.
Same problem with mine, have applied the touchscreen tweak and aligned the screen which does make it a little better. Maybe the 1.48 rom will fix it and the camera when its officially released.
dude that is exactly what i got. its hard to write one word without the need to correct it. the keyboard is such a horror. it was easier to write on my diamond. im still thinking about to get money back, ask for a replacement or wait for an update.
Unfortunately rom 1.48 does not solve touchscreen problem nor camera pink issue.
So it's a hardware problem ?
adolfotregosa said:
Unfortunately rom 1.48 does not solve touchscreen problem nor camera pink issue.
Click to expand...
Click to collapse
Why don't you take your phone back and go get an iPhone instead? Complaining about it here isn't going to help any and it's not, as far as I can tell, a general issue as plenty of people do not see this effect (myself included).
just tried 2 of the tests on mine and i do not get any of the problems.
I just got an HD2 a couple of days ago on O2 in the UK. I have the stock 1.43 ROM at the moment and have this keyboard jitter really bad too . Should I ring O2 and get a replacement, or is a new ROM likely to fix it?
Cheers.