cingular 8125.
I need the original rom file (original firmware )can anybody help plz right now my fone stuck on the RUU mode can anybody help
If it is realy a brick without any chance of life I need a part of it: the keypad.
Thats really rude.
not a complete brick yet
not a complete brick yet is in loader mode red,blue ,green screen
All the cingular roms are here ftp://[email protected]/Wizard/Roms/Cingular/
user name xda password xda
which rom do you have?
It looks like you are in bootloader (multicolored) mode so that is good
connect via usb - you dont need to activesync to update rom. You should get a usb sign bottom left of screen and then start update.
Upgrading without activesysnc
After a interruptus ROM upgrade my s200 d'ont start . after the HTC i have a white screen but not more.
The activesync don't connect and i can't put the ROM another time.
I obtain the multicoloured screen with usb in the left botton.
Please, could anybody help me to update the rom in this situation , mayby without activesync ??
Regards.
You can flash a rom from the 3-colored bootloader mode (hold voice button when turning device on). When it says usb you can just flash without activesync.
Yes thank's i found a ROM that don't need activesync , after that i had changed that rom by my rom and at the moment my s200 y ok.
Thank's.
Related
I have updated my Radio ROM to 2.24.10 (T-Mobile-US_2.24.10_Radinly) but it crashed. Windows is starting but the phone is not working, and I can't connect with activesync to install the backup.
Please help me!
I have kind of the same problem, I allso didn't find a solution yet...
If you find one, could you tel me?
thanx...
3s
Restart the phone and keep pressed the camera button while the phone will go in the bootloader mode With the USB-cable connected, on your phone screen will apper "USB" in one of the corners... Now you cand install the radio ROM for your device. I suppose that you know where you can find the radio ROM you need...
anymore. :--(
Yesterday i^ve make a setup for the ext_rom but with a wrong update. It was been not for the Artemis..my fault.
Now i see only th et-mobile start screen and no more.
What can i do? Thanks in advance..
hmm, please flash your p3300 whith the original software with hope that it will be alive again. otherwise you can take an hardreset on your phone but i'm sure that there will not happened.
is your PDA an original fom HTC or from any other Provider?
it`s from t-mobile
and a hardreset doesn`t work and it`s not successful.
How can i flash it again...how i get usb connection to do it?
dr.moppi said:
and a hardreset doesn`t work and it`s not successful.
How can i flash it again...how i get usb connection to do it?
Click to expand...
Click to collapse
hello there!. i have the same problem, did you manage to get a usb connection? i can't flash it...
Try to get it into bootloader ( Read the Artemis wiki as to how to get into bootloader) and if you are successful then try flashing it with the t-mobile stock rom.
arvind09 said:
Try to get it into bootloader ( Read the Artemis wiki as to how to get into bootloader) and if you are successful then try flashing it with the t-mobile stock rom.
Click to expand...
Click to collapse
Please tell me how can i get the t-mobile stock rom or can you give me the link, thanks
Shipped ROM's in English - http://wiki.xda-developers.com/index.php?pagename=Artemis_Upgrades
To get into bootloader - hold down the record/voice command button (top left along the side of the phone) and use the stylus to press the recessed reset button on the lower left side of the phone (same side as the other boutton you hold down) Keep holding the record button as you hit and release the reset button, you will eventually see a screen with color bars on it. At this point you will be able to get a USB connection, but not an active sync. Try to start the ROM file when the phone is in this state and connected to your computer.
What is the original language/carrier for your phone?
MDA Compact III stops in T-mobile logo screen
I manage to enter bootloader and start flashing a ROM but I allways get a error: image file corrupted.
I think I need the original Dutch T-mobile ROM.
Anyone know where to find it?
Hi I have the same problem. I have the B&B3.7 and get stuck in the splash screen. I could enter to the bootloader mode and use some commands of the mtty.
I have my old rom, how may i load it to the pda? I have a SD and a tytn to load something in it.
Thanks!
Hernan
ftsv said:
I manage to enter bootloader and start flashing a ROM but I allways get a error: image file corrupted.
I think I need the original Dutch T-mobile ROM.
Anyone know where to find it?
Click to expand...
Click to collapse
run uspl first!!! you can then run installation from any provider of your choice.
http://forum.xda-developers.com/showthread.php?t=311403
USPL cannot be run if your phone is stuck into bootloader?
It starts counting, askts to copy the same information again several times, and get stuck at 50... how is this possible, anyone has the original HTC Dutch rom ? May be the WM5 also! Thanks!
same problem but with no display
i have done the same mistake
have tried to upgrade my T-MOBILE MDA COMPACT III(aka htc p3300) with the HTC TOUCH ROM
it started to upgrade and an error occured
then i have lost the display and all
when i connect it to my laptop using USB i hear a beep in my computer but active syn didnt find any device
i dont know what to do now..please help me it has to be recovered
there must be some way pls pls anyone help me to get my working phone back
will appreciate your concern
thanks
Regards
Faraz Feroz
well you have to get the original ROM for your device.. see their website.. it should be there for free. or try to get it from anyplace.. (the original rom)
and then flash it using SD Card flashing
info for flashing it by that are here:
http://wiki.xda-developers.com/index.php?pagename=Artemis_SD_Card_Flashing
hope it will work
y_bother said:
well you have to get the original ROM for your device.. see their website.. it should be there for free. or try to get it from anyplace.. (the original rom)
and then flash it using SD Card flashing
info for flashing it by that are here:
http://wiki.xda-developers.com/index.php?pagename=Artemis_SD_Card_Flashing
hope it will work
Click to expand...
Click to collapse
thanks Y_Brother
i have downloaded the new rom but it doesnt seem to work too
please help! I have made a wrong ROM Update for my Artemis. The result is that it doeasn`t starts anymore. I see only the start screen no more. If i make a SW or HW reset tahn i see a 3 colored screen and USB. But i don`t get a connection via usb to my compute`! How can i wake up my Artemis ???
tell use more what did you do and how did you do it?
what artemis is it?
what rom was it
Flash went sour..
You need the original ROM which was on your device when you bought it. What version (HTC, MDA, etc..) and what language was the original ROM?
please i need help too
I guess I made the same or a similar mistake that dr.moppi did. My machine is a Dopod P800 from mainland china with the chinese operating system. I flahsed it with PDAMobiz_Dopod_P800W_AKU301_v1.1.2_PowerMap. Don't really remember what the original ROM was but now when i turn it on it freezes when it lights up. On the screen, it says
IPL 1.27.0001
SPL 1.27.0000
GSM 02.67.90
OS 1.28.0.0
DOPOD
I don't get a connection through usb to the computer either. I am not sure if I did the hard reset correctly. Didn't understand the instruction on that "press the soft key left and right and soft reset at the same time." Anyway, you guys are all experts, can you help me please?
it should be the same as my problem
if i remeber than i used the same ROM Update :-(
I hope anyone could give us a solution, please.
@dr. moppi we can only help you if we know what version you had before.
@empathyvirus you have to look for the original ROM which, in your case, should be the Chinese Dopod ROM. Install that one and your good to go.
Without the original ROM the only thing left to do is: sending your device to your provider or contact and sent it to the guys of imei-check. Either way, you'll probably have to pay to get it fixed.
how to install original rom
Thanks for your quick reply Pyth. In the case I get the original ROM from somewhere, how do I install it if I can't get a connection between the phone and my computer? Can you advice?
Put your device in bootloader by pressing the record button and reset at the same time. If you have your USB-cable connected between your PC and your phone it will indicate a connection by 'USB' in the left corner of your device. Now you should be able to run the ROM executable and update your device.
thanks anyway
i tried but it didn't seem to work. anyway, i have troubled you enough and maybe it's best i just go to the repair centre of dopod and pay for a fix. i really appreciate your help though Pyth.
Where can i find the t-mobile rom its the MDA Compact III that wont start for me
Hi Wizards,
Im having a Qtek 9100 and using a ROM cooked by Mfraazz. The phone application seems to hang and i have to reset in order to make it functional...the problem does not end here. When the phone boots up, the start menu bar is not visible...I have to hard reset my device 3 -4 times..thats whn the start menu is visible..
I have only one application(Good Link) running...plz help me guyzz
it is time to donate to XDA-developers!
Just reflash the ROM, friend. Seems to be a bad flash to me.
deleted this post
wiztek said:
Hi Wizards,
Im having a Qtek 9100 and using a ROM cooked by Mfraazz. The phone application seems to hang and i have to reset in order to make it functional...the problem does not end here. When the phone boots up, the start menu bar is not visible...I have to hard reset my device 3 -4 times..thats whn the start menu is visible..
I have only one application(Good Link) running...plz help me guyzz
Click to expand...
Click to collapse
try another cooked ROM or an official one and see if problem persists...
the mfrazzz crossbow reloaded made my kjam hang on the bootloader as well n my fone cant b detected by active sync either plz help how m i suppose to flash another rom wen active sync itself dont detect my rom
z0d1ak said:
the mfrazzz crossbow reloaded made my kjam hang on the bootloader as well n my fone cant b detected by active sync either plz help how m i suppose to flash another rom wen active sync itself dont detect my rom
Click to expand...
Click to collapse
Rom has got nothing to do with Activesync not detecting your phone,it's most probably the problem of Activesync application or your USB cable not establishing connectivity.Check the usb connectivity for problems.To verify the connectivity,check if it gets charged via usb connection.
secondly,get your phone into bootloaders and connect it to your Pc via usb cable,see if usb appears at the bottom of the bootloader mode (multicolor screen),if it then it's connecting.
You don't need Activesync for flashing a Rom to your phone,it's done via usb cable,and while flashing activesync is automatically turned off by the Ruu.So if you are able to establish connectivity via usb cable in bootloaders (multicolor screen) you can flash to any Rom.
Cheers
Hi,
Il from Belgium. SORRY FOR MY BAD ENGLISH
I have a Qtek S100
R 1.01.00
G 133.38
D 1.03.02 FRE ( French i think )
I tryd to change my Extended Rom from French to Dutch or English... with some file i dont know... im new it this stuff and i F**kt it up!!!
My Qtek just goene black and on the screen u can see USB 1.0.0
After open the baterycover and plug in back the qtek starts BUT after starting install the original app. it goes back to thr BLACK screen and nothing happens.
If I plug in the USB and connect it with my pc, it comes on the screen USB 1.0.0 ....
SO PLA HELP ME PLS!!!
I tryd hard / soft reset, NOTHING!
I look at XDA alredy 4 days everyday 4-6 hours I tryd SO MUCH, I take a day off work, so to can fix it!
IM GOIN CRAZY PEOPLE!!! PLS PLS HELP ME!
Best thing to do is go to bootloader mode and installing a new flash.
Bootloader mode can be found on the forum, but to help you out:
press simultaniously: camera button + power + soft reset (last one with the stylus)
Then start the rom update on your pc (do not use this from vista it wont work (or you have to find the fix online..)
Easiest way is to flash from windows xp works like a charm.
I have the same problem than rocky_gent but I can get the bootloader mode
i'm stack in bootloader mode ! And when i connect the usb cable doesn't display the "USB" but insists with "Serial V1.00".
I want to upgrade my rom from a secure digital (sd) cause i don't have another choice!
I 've been surfing through forums but i only found how to make an sd to upgrade your phone when you have an mda or xda (.nb1 files) . Qtek's roms have .nbf files !!! So i'm looking instructions to make an upgrade sd card with .nbf files (Qtek , Htc Magician) and not .nb1 (Xda)!!
http://forum.xda-developers.com/attachment.php?attachmentid=24569&d=1127232848
?
where can i get new flash? and yes im with vista, why it wount work???