How to use the MTTY.exe ?? - 8525, TyTN, MDA Vario II, JasJam General

After many tries I think i´m to stupid th use this little program.
I´ve connected my Vario II in bootloader mode ,Activesync is disabled.USB is selected.All other checkboxes are default.
I´ve got the "USB" prompt.
If I use the "rtask b" command to enter the GSM AT command interface, I can´t make any inputs in MTTY.I can´t even go back with "returoR" to normal bootloader.
If I disconnect the USB cable the Hermes didn´t change from USB to serial.
What did I wrong?
It´s Hermes 300; IPL-1.01; SPL-1.04
Thanks for your replies
scorpio16v

When you type 'rtask b' and go to GSM bootloader you have no "local echo", that means what you type is not printed on the screen.
To enable local echo you have to type "ate 1" and press enter, also it is good to type "atv 1" for better responses.
To exit, you have to type "retuoR", but sometimes 3 times before it exits.

pof said:
To exit, you have to type "retuoR", but sometimes 3 times before it exits.
Click to expand...
Click to collapse
Thanks pof
The word "returoR" semms to be a mistake in the Wiki.

thanks, fixed

not sure why .. all i got is "cmd" instead of "usb" ... ?

when i try to conect mtty with my hermes, it open a window when usb is selected and all other radio default..it shows CLIENT CLEINT
and doesnt allow to enter any command..i can copy paste but command has no effect..what is wrong..i have disabled usb connection from active sync

Related

get wizard connected to mtty for call timer reset

i want to clear my call timers, i got this method -
Code:
1) put device in bootloader mode
2) disable activesync usb connections
3) connect to bootloader using mtty.exe
4) when you see "USB>" prompt type this (DO NOT COPY-PASTE):
USB> rtask b
0 <--- wait until you see a "0" here
ate1 <--- enable local echo
atv1 <--- verbose output for return values
[email protected]?1 <--- get outgoing call time
[email protected]?0 <--- get incoming call time
[email protected]=<value1>,<value2> <--- set incoming and outgoing call
its for hermes but i think it will work for wizard(supercid) too,
when i connect device in bootloader mode, select usb from drop down, it gives me a CMD> prompt instead of USB> prompt, also when i type usb and press enter in usb prompt it says "I already connect to USB!" anyway to get the usb prompt ? or clear lifetimer, i need to sell this at good price and get a hermes
(nevermind)

Four colors screen after radio 1.58.25.14 upgrade

Hello,
After I tried to upgrade my Polaris Radio Rom to version 1.58.25.14, instalation stoped at 99%.
Now when I just turn on my device without USB cable connected I get always the Four colors screen. ( POLA100 ; SPL-1.25.0000; CPLD-2)
I already tried to upgrade many times the radio rom, the full rom, according with the described on 'How to guide: HardSPL ' but when I try to upgrade the info about Image version at the 'Step 4' doesn't appear, and at this step the device already presents the evolution bar stopped at 0% and doesn't pass this...
After a while I get always the same message 'ERROR [262]: UPDATE ERROR'.
What can I do to RESOLVE THIS PROBLEM ?
PLEASE HELP ME !?
Thank you in advance !
i think u shuld wait, coz it takes somtime on 99%
sorry ... you havent read all threads about radio rom flashing carefully!
download the programm mtty and use the command "boot" to start you OS again. then you must flash hardspl. after that ... you can flash a radio rom.
your device isnt bricked or damage!
You can try this....
1. Stop ActiveSync
2. Open Task Manager (press Ctrl + Alt + Delete) on your PC and
stop these two processes rapimgr.exe and wcescomm.exe
3. Plug in your device via USB. Your computer should be asking install a driver. Install and continue.
4. Now Run mtty and choose USB in 'PORT'
4. type "set 16 0" without the quotes to tell bootloader to boot the OS after reset.
5. type "task 8" to get your device formatted.
6. Now unplug your device and manually reset it.
Should work... I used it a while back with a Hermes and I just guided someone else with the same problem as you through it.... and it worked.
I can confirm that the method indicated by Christonge works fine
PQillu,
Thanks mates !
It worked, I finally have my Polaris alive !
disable under Vista
I would like to disable the Center of synchronisation under Vista and I have no idea how to do.
epsimax said:
I would like to disable the Center of synchronisation under Vista and I have no idea how to do.
Click to expand...
Click to collapse
Welcome to the forum, mate, but please post specific questions
in specific threads meant for that (not being offensive 2U though)
In your case I would suggest THIS ONE
Cheers, Olioaglio
christonge said:
You can try this....
1. Stop ActiveSync
2. Open Task Manager (press Ctrl + Alt + Delete) on your PC and
stop these two processes rapimgr.exe and wcescomm.exe
3. Plug in your device via USB. Your computer should be asking install a driver. Install and continue.
4. Now Run mtty and choose USB in 'PORT'
4. type "set 16 0" without the quotes to tell bootloader to boot the OS after reset.
5. type "task 8" to get your device formatted.
6. Now unplug your device and manually reset it.
Should work... I used it a while back with a Hermes and I just guided someone else with the same problem as you through it.... and it worked.
Click to expand...
Click to collapse
Nice one, mate!!!
christonge said:
You can try this....
1. Stop ActiveSync
2. Open Task Manager (press Ctrl + Alt + Delete) on your PC and
stop these two processes rapimgr.exe and wcescomm.exe
3. Plug in your device via USB. Your computer should be asking install a driver. Install and continue.
4. Now Run mtty and choose USB in 'PORT'
4. type "set 16 0" without the quotes to tell bootloader to boot the OS after reset.
5. type "task 8" to get your device formatted.
6. Now unplug your device and manually reset it.
Should work... I used it a while back with a Hermes and I just guided someone else with the same problem as you through it.... and it worked.
Click to expand...
Click to collapse
how can i get mtty and how its work?
christonge said:
You can try this....
Very very cool!!!
I have my Polaris back now !!!
Tanks !!!
Click to expand...
Click to collapse
>> type "task 8"
this step is really optional. no need to re-format if you stucked in bootloader mode usually. device will boot after "set 16 0". this command sets device to use normal mode instead of bootloader mode upon reset.
ommiting the task 8 will save you from reinstalling all you programms again and form other data losses associated with hard reset.

Upgrade without usable Mail button

Hello
I want to upgrade my MDA3 from WM2003se to WM06.
After i have read the upgrade artikel, i have seen, that im must change this
"Enable KITL” must be NO, “Clean Registry Hive” must be YES, “Format Storage” must be YES"
And here is my problem, my 4 buttons (Mail, Explorer, Windows, ok) in front of the MDA are Defect. So i can´t confirm the Options.
Are ther other ways to do this.
MFG Kleinepelle
PS: I know my english is very bad
Logically if you map the mail button to any of the top buttons, that should work as BA still keeps the entire software prior to pressing mail button. However an expert should confirm. Dont take risk.
Upgrade without usable mail button
kleinepelle said:
Hello
I want to upgrade my MDA3 from WM2003se to WM06.
After i have read the upgrade artikel, i have seen, that im must change this
"Enable KITL” must be NO, “Clean Registry Hive” must be YES, “Format Storage” must be YES"
And here is my problem, my 4 buttons (Mail, Explorer, Windows, ok) in front of the MDA are Defect. So i can´t confirm the Options.
Are ther other ways to do this.
MFG Kleinepelle
PS: I know my english is very bad
Click to expand...
Click to collapse
Hi there ... I have the same kind of problem with my O2 XDA IIs Blueangel. The mail button along with the other 3 (home,ie,ok) are not working or not responding anytime.I was not able to upgrade my rom and format the registry hive
But then i found a much simpler way to do it..
Try the following to format your rom,clear registry hive and upgrade to a new rom-all this even with the mail button not working.
You will need the program MTTY(Attached with this post).
1) Kill activesync processes: Ctrl+Shift+Esc in Windows to bring up Task Manager. Kill wcescomm.exe and WCESMgr.exe (by selecting the task on the processes tab, and clicking the End Process button below)
2) Phone needs to be POWER + Record + Pen Reset and on Serial/USB screen. COnnect it to the PC, and it should show USB, with the backlight remaining off.
3a) Run mtty1.42.exe
b) Select USB from first list (where COM1 is displayed. Don't press USB button). If USB (or a list item containing USB) isn't in the list, then you have't connected to the PC properly.
(Leave default parameters: 8 bits / Flow Control NONE / Stop bits 1 / Parity None / Local Echo No)
c) Click OK
3) Run following commands:
[press enter first to get USB> prompt]
USB>
5. type "set 14 0" without the quotes to tell bootloader to boot the OS after reset.
USB>set 14 0
HTCST ÚÈHTCEUSB>
6. type "task 28" to get your device formatted
USB>task 28
DOC_format_HW+
DOCInfoTableinitHW+
Binary0:dwSize=80000
BINFS0:dwSize=0
FAT0:dwSize=1000000
FAT1:dwSize=2BA0000
All:dwSize=3C20000
USB>
7. type "task 0" to ask your device reboot
USB>task 0
USB>
8) Exit the program, then re-hard-reset (POWER + Record + Pen Reset), leaving on USB screen in order to run ROM Flasher
9)Now be back to the Usb/Serial screen and run your favourite ROM upgrade-A clean installation
Please let me know if this worked for you too. I believe this was my great geeky work i did with my BA. Was so frustrated when the buttons were not
working.
P.S: This is not my own work. I got the Mtty app from this same forum and the steps too. I am terrible sorry if i have repeated a post or done something i should not
Thank you very much.
It runs very good.
MFG Kleinepelle
Great advice! this should be placed in the wiki as well
Thanks to you and to all others <ou mwntioned for this help. Dtipex
thanks, it works!
thanks, it works!!
crabiorc said:
Hi there ... I have the same kind of problem with my O2 XDA IIs Blueangel. The mail button along with the other 3 (home,ie,ok) are not working or not responding anytime.I was not able to upgrade my rom and format the registry hive
But then i found a much simpler way to do it..
Try the following to format your rom,clear registry hive and upgrade to a new rom-all this even with the mail button not working.
You will need the program MTTY(Attached with this post).
1) Kill activesync processes: Ctrl+Shift+Esc in Windows to bring up Task Manager. Kill wcescomm.exe and WCESMgr.exe (by selecting the task on the processes tab, and clicking the End Process button below)
2) Phone needs to be POWER + Record + Pen Reset and on Serial/USB screen. COnnect it to the PC, and it should show USB, with the backlight remaining off.
3a) Run mtty1.42.exe
b) Select USB from first list (where COM1 is displayed. Don't press USB button). If USB (or a list item containing USB) isn't in the list, then you have't connected to the PC properly.
(Leave default parameters: 8 bits / Flow Control NONE / Stop bits 1 / Parity None / Local Echo No)
c) Click OK
3) Run following commands:
[press enter first to get USB> prompt]
USB>
5. type "set 14 0" without the quotes to tell bootloader to boot the OS after reset.
USB>set 14 0
HTCST ÚÈHTCEUSB>
6. type "task 28" to get your device formatted
USB>task 28
DOC_format_HW+
DOCInfoTableinitHW+
Binary0:dwSize=80000
BINFS0:dwSize=0
FAT0:dwSize=1000000
FAT1:dwSize=2BA0000
All:dwSize=3C20000
USB>
7. type "task 0" to ask your device reboot
USB>task 0
USB>
8) Exit the program, then re-hard-reset (POWER + Record + Pen Reset), leaving on USB screen in order to run ROM Flasher
9)Now be back to the Usb/Serial screen and run your favourite ROM upgrade-A clean installation
Please let me know if this worked for you too. I believe this was my great geeky work i did with my BA. Was so frustrated when the buttons were not
working.
P.S: This is not my own work. I got the Mtty app from this same forum and the steps too. I am terrible sorry if i have repeated a post or done something i should not
Click to expand...
Click to collapse
very well explained . good job

Hermes (TyTN) Call Duration Reset

Hi. Please tell me a metod to reset call duration at HTC TyTN.
This is for personel use, not to resell on ebay as "NEW"...
How to reset call timer (if you want to know reason why you want to do this, please do additional research)
a). Please make sure that you are SuperCID and you understand the importance of hard spl as this maybe a dangerious operation for you.
b). Make sure that you have SPL 1.10 Olipro (this one works for me, higher version seems not work)
c). Download Mtty.exe and save it to your computer.
d). Open connection setting of your activesync or WMDC on your PC and disable "Allow USB connection".
e). Put your device into Bootloader mode and connect to your PC via USB
f). Run Mtty.exe from your PC
g). Select "USB" in port box and then click OK
h). Press Enter once or twice to let the screen dispay "USB>" or "CMD>"
i). Type "rtask b" and Enter then it should show result "0"
j). then type "ate1" and Enter then it should show result "0"
k).then type "atv1" and Enter then it should show result "OK"
l). then type "[email protected]=270f,270f" and Enter then it should show result "OK"
Restart you PPC.... you call timer should be 00.00.00
Cheers....
Where I finde Mtty.exe? Please help.
On the top bar is a little thing called "search", try there....
hello can you say me if this method work for htc tytn 2? thank you
thanks ultramag ...quick answer... some months ago i was curious and had to read many threads to even undestand. thanks

[Q] hw6915 wm6.1 rom

Ok..so first of all thanks for clicking on my thread.I hope somebody can help me flash a rom.I can't post the link because I'm new....I added a text file with the link(yes, it's on xda)
Post #9 describes a process of flashing this rom.
My device: HW6915 vG.39 G4(flash chip)
I am having trouble with this step pdocwrite spl -n0 -b 0x20000 0 0x80000.
Yes I know what the bootloader is and I know how to get into it.So after I connect the device via usb(while in BL mode) i run the command mentioned above.The problem is that nothing happens(screenshot included),it just stays at the same command and does not progress at all.CPU usage is little to none.And if I do try to flash the rom anyway the progress bar on sable_RUU gets stuck at 1% and after a few minutes gives an error.I tried this on XP 32 and on 7 64.
Yes, this is my first post, so take it easy.
Thanks for any help.
hello. i have the same problem but my sable ruu progress bar freezes at 51% and then pop up error:201. help?
For you it's stuck at 51% because you also flashed the bootloader(CEBL.nbf).I chose not to as it's optional.Even so I'm still stuck on the original problem.
Anybody know the answer to this?
my problem is identical. i am also having trouble with pdocwrite spl -n0 -b 0x20000 0 0x80000.after i run the command nothing happens,it just stays at the same command and does not progress at all as in your case. then when i run sable_ruu it freezes at 51%
did you try...
did you try opening the command prompt as administrator?
Code:
1. Click on start
2. Type command
3. Then either right click and then pick run as administrator or just CTRL + SHIFT + Click
If that doesn't work you can try disabling UAC by clicking start, typing UAC pick the first option then dragging the slider to the bottom and restart computer
You need to write SPL when phone is on and connected with ActiveSync, not in bootloader.
Spiaatie said:
You need to write SPL when phone is on and connected with ActiveSync, not in bootloader.
Click to expand...
Click to collapse
Ok it works thanks guys for all the help.
Will report back to your thread and tell you about my findings
Thanks,appreciate it
Thanks from me too. On the first look wm 6.1 runs faster than 5.0 and gps does not work (igo 2006 plus-can not find gps com port).
my suspicions on gps is it might be driver related in asset viewer (Settings/System/MyCPL 7) under GPS it used to state whether it was on or off in WM5 but now it says N/A
jambongo said:
my suspicions on gps is it might be driver related in asset viewer (Settings/System/MyCPL 7) under GPS it used to state whether it was on or off in WM5 but now it says N/A
Click to expand...
Click to collapse
Yes the driver is indeed missing as this is ported from a hp without gps(i guess so anyway).First clue is that it doesn't include any base navigational software.
Second igo 8 reports ''gps driver not found''
n can you! help???
you seem to know how to proceed to tryin' roms on you hw6915;
......i don't!
can u help me, i'm really a newbie on this!!!
i wish there was an "upgrade your ipaq verson for dummies" or somthing!!
i got the hp ipaq hw6915, an usb connector, Internet access!! anything else?
oussahoo said:
you seem to know how to proceed to tryin' roms on you hw6915;
......i don't!
can u help me, i'm really a newbie on this!!!
i wish there was an "upgrade your ipaq verson for dummies" or somthing!!
i got the hp ipaq hw6915, an usb connector, Internet access!! anything else?
Click to expand...
Click to collapse
Beware dude this is higly experimental.There is no GPS for example.The rom is wm6.1.This is just for people who want to test and no it obviously not official.All files can be found at the link in the TEXT file I attached to my first post.
1.Connect your device to activesync(suggest a hard reset first,however it's optional)
2.Extract SPL vG.39.7z anywhere you want.
3.Run ''Command prompt'' (if using vista/7 RUN AS ADMINISTRATOR)
4.Enter this command pdocwrite spl -n0 -b 0x20000 0 0x80000 (WAIT UNTIL IT FINISHES).This command replaces a file in the ROM which allows you to flash ''non-original roms'' basically software CID unlocking which allows flashing of ''cooked roms''
5.You will get warnings on your hp regarding a dll file(itsutils.dll) PRESS YES
6.Put your device in bootloader mode.[hold the two buttons next to the joystick(the round thingy) and shortly tap the reset button with your stylus
7.Open activesync,go to connections and untick allow USB connections
8.Extract 6915_ENG.7z and run Sable_RUU
9.Press on the big ''Upgrade button''
10.There will be a progress bar, when it's done it should say something like '' Update finished !!''
11.Go back to activesync and re-tick allow USB connections
I wrote this for everybody who's got trouble flashing roms on their hw69xx.Yep I had this problem too.
This detailed enough?
jambongo said:
did you try opening the command prompt as administrator?
Code:
1. Click on start
2. Type command
3. Then either right click and then pick run as administrator or just CTRL + SHIFT + Click
If that doesn't work you can try disabling UAC by clicking start, typing UAC pick the first option then dragging the slider to the bottom and restart computer
Click to expand...
Click to collapse
A question ....
but it happens to me the same error in XP and not out of the 1% resulting in the error 201
Can you help me!
hi
I have the hw6915
to me the procedure doesn't go
he/she writes me "client_initialize Fail Error 601"
a question: what I write on the Command Pront
thanks
for further information
the cell doesn't connect him to activesync
it is jammed on screens her/it USB - LOGO HP INVENT and in low vG.39
THANKS
@spiaatie
mine is in bootloader
however it doesn't connect him with Activesync
what do I have to do?
which procedure do I have to do?
thanks
can't program ipaq 6945
When ever I push upgrade button, it just hangs and afer a while I get the message:
client_getosver Fail !! Error :501
I'm using it on windows XP,
could someone help me!!!
Thanks!
rra_pn said:
client_getosver Fail !! Error :501
Click to expand...
Click to collapse
Did you install SPL?
Yes, I did de pdcowrite on command prompt, then it gave me the warning on my ipaq and then it finished.
After that I unticked the allow usb connections on active sync
then I press the two buttons next to the joystick and press the reset
I run sable
and then it does what i Posted
Thanks!

Categories

Resources