hello, can anyone help me?
my mda compact just soft resets constantly.
I switched it on and the t-mobile screen appeared then my password screen appears and then it soft resets immediately. There is nothing i can do. It just constantly refreshes. I cant even switch it off, without removing the battery. Nothing appears to stop it.
Can anyone help?
Thanks
Euan
did u try to hard reset it cuz that would solve any problem of software conflicts u would lose all the info u have on the set ( storage card will remain unchanged) but atleast ur set will be working again
and if u dont know how to hard reset there is a small depression on the right hand side of the usb port on ur set using the Stick that came with ur set press the button in there and at the same time press the power switch located on the right hand side of the set that would cause it to hard reset
Alternativly u can take out the main battery and let the internal batterys charge run out(taking approximatly 30 min) after the batter is fully dead reinsert ur main battery ur set will have hard resetted
Related
My O2 xda mine refuse to start-up. I'm traveling this week without mobile phone, so any helps will be highly appreciated.
Problem description:
- Using the camera/video mode and acidently forgot to turn off mobile for a while.
- It was hange with screen changed to very strange color like negative film colors
- Press reset in the bottom of the phone, try to restart but then couldn't start-up succesfully. keep hang at the start-up screen only.
- Have to take-out the battery cover to turn it off, and turn-on by pressing the power button.
- Problem was even worst when it couldn't even show up the start-up screen anymore. If i press power button the blue light will blink once and then nothing happend.
P/S: not sure about the ROM version, since i couln't turn-on my phone at the moment. Cldn't find this info from O2.com website either.
Most probably you're battery is bad. Have your tried a hard reset?
How to do a hard-reset?
I've tried the reset button in the bottom. Is it the correct way?
If this is xda battery issue then could be fairly easy to check-out by a brand new battery.
kalau nak hard reset, press power button + tekan lubang reset.
try hard restart the cellphone, maybe it will solve the problem, if not, contact the local service for repair
What is address of local service in Kuala Lumpur?
What is address of local service in Kuala Lumpur?
Imbi or Low Yat Plaza?
Hard reset by press power + reset buton simunteneously?
I'm not Malaysian so I don't realy understand writing in Malay
To do a hard reset you need to press and keep pressed the camera and power switch while pushing the reset button.
Plug it into the wall charger rather than the PC USB.
Hard reset & recharging the battery solved problem
I've tried the hard reset and the re-charging the battery by using USB connetor.
It took about more than 15' minutes to re-charge and once the power is sufficient the installation process starting.
My cell phone is working properly now. All Microsoft Outlook related data was restored succesfully
Thanks a lot
Was working OK...went to install spb clone..asked if I wanted to make a clone of the device on my existing mini-SD card..I said yes. Now it hangs at the "Windows Mobile" screen...
I tried the Hard - Reset (push the two buttons and hold in the soft-reset button, press green phone button...) and also taking the battery out.
It boots up with Cingular screen with info about ROM then goes to Windows Mobile screen...that's it. The BT and green power light flash (I had on BT before it crashed)...
Anyone have any ideas...? I hope it's not fricked up...of course I could always take it back I think...
TIA...
--Jack
did you hard reset without the sd card in the device :?: :?
I left the card in and waited for some time the first and second times...now I have the card out and also the battery out hoping it will boot when I put the battery back in..
Any way to "re-ROM" this sucker?... :shock:
dont know about re-rom, but my guess is it should load fine without the sd card, i suspect the card may have become corrupt which is causing the device to hang, had similar problem myself after installing pocket mechanic it took a hard reset and a format of the card to solve it :roll:
heres hoping it works for you after hard reset :wink:
been trying to hard reset it for a while now...still hangs at the blue windows screen. hooked it up to the pc and will try to install a diff rom and see what other type of damage i can do. :roll:
Can you get your wizard into USB mode by holding down the voice command button, hitting the reset button with your stylus, and continuing to hold the voice command down for a couple seconds until you get a three-color screen?
If you can get to this screen, your bootloader is intact, and there is still definite hope for your device.
Got it working...weew...
Left the battery out all night..did a hard reset and got the "format complete" on the black screen..after that...it was ok.
thanx for all the help guys..
hi guys, this might seem to be posted a lot of times but i havent found anyone who experienced the same problem as me. ive flashed a custom rom (not found in xda dev) and the phone went well for 3 weeks to a month.however, today(lunchtime) i had a problem i soft reset my device and i was stuck at the 2nd splashed screen. i dont think my hermes is bricked because i can do anything a normal hermes do before. (pda function, calls, sms) really no problem at all until today. ive done what the wiki said like
Problem 2: stuck on windows mobile screen
Try to soft reset with stylus and wait 5 minutes on the windows mobile screen to see if OS boots
If all you get is same windows mobile screen, remove the battery for some time (about 20 min should be enough) and put it again.
Again, if all you get is same windows mobile screen do a hard reset.
If doesn't solve the problem do a hard reset, but do not press spacebar to reboot after. Instead, do a soft reset with stylus when the device asks you to press spacebar.
Check if you might have the NO GSM Problem
well i cant go pass the 2nd splash screen so what i did was hard reset it. and problems gone. my concern is ive lost a lot of documents because of what happened. so i just wanna ask you guys what could be the problem and the solution to prevent this from happening again.
much respect to all here!
TIA
What do you do just before the problem occur?
best thing to do is hard reset you phone this will reinstall you OS and resolve the problem. You need to old the 2 top soft key and press the reset but with your stylus. This will then bring then take u into the hard reset mode. follow the prompts on ur screen by using your keyboard .
This will work as i have experienced the same problem
kind regards
Ash
Did u happen to
a) disable the bottom tray
or
b) set PIE cache to storage card?
Both tend to cause this, tho not in every case.
hi guys
Did u happen to
a) disable the bottom tray
or
b) set PIE cache to storage card?
Both tend to cause this, tho not in every case.
ive done both of this in my ppc. hehehe
@sir mikechannon
yeah that was my badd. havent done bckup and all. hehehe
@sir ghz
hmmm nuthin, just the usual... havent installed anything prior to the problem.
well guys... thanx for the comments my ppc doing good now, i just hope it wont happen again. hehehe. much respect!
recently my xda neo been working so slow. The peak is when i was playing a game on it, it hanged. I thinked its just my neo take some time to load so just let it on. After several mins, it suddenly went off and i cant turn it back on. And the saddest thing is i lost my usb cable and cant connect my device to my pc. I heard about bootloader, whats that actually do? Any idea how to solve this? Help will be much appreciated. Thanks in advance.
Hard reset
Try hard reset....i also have a xda neo & have similar problem after i installed hangman(i know...lol)....hard reset & done....to hard reset go 2 clear storage in setting & press 1234...if u have tried it...i read it one thread...user had similar problem & found out battery died...
RieLL said:
recently my xda neo been working so slow. The peak is when i was playing a game on it, it hanged. I thinked its just my neo take some time to load so just let it on. After several mins, it suddenly went off and i cant turn it back on. And the saddest thing is i lost my usb cable and cant connect my device to my pc. I heard about bootloader, whats that actually do? Any idea how to solve this? Help will be much appreciated. Thanks in advance.
Click to expand...
Click to collapse
Dude,
You can Hard Rest your device through Clearstore only when the device is running. I assume your device is not powering on, so Hold the Camera Button and the Third button i.e, the Comm button and with your stylus push the reset button. Hold the first two buttons till your get factory reset message on the screen. Once on that screen, press the green button, ie. the call making button. The device will restore itself to the factory settings.
Good luck.
Please help me, nothing happened my qtek s200 is dead i have the same problem suddenly it turned off and never went on again, i replaced the battery and nothing happened just a red light turn on when i connect it to the wall charger. Please help
Hi all
first post and i got an interesting problem with my phone which i qualify as stupid. It all started when when my virtually keyborad started becoming unresponsive and when i tried to do a factory reset, i could not enter the 1234 number to start it. i left the phone for a while and then i could not get into the setting even . But i could receive calls but i could not call since i could not access any numbers on the dial pad( by pressing on the numbers of coruse but from dial log screen i could)
Anyway long story short while fiddling with the phone , i thought the lock feature was on that is why some of the touch functions was not totally responsive but to my sadness, i activated the lock and now the phone is stuck on the front page and i cannot access anything since i must press unlock at the far corner of the down screen but stupidly, while pressing on the unlock, since it is unresponsive, i cannot unlock the phone to get to the normal menu and so on.The only thing working is the square pad which tells me to press cancel then unlock to free the phone for normal use
By the way the lock feature is the one that blocks the phone so that you do not accidentally press on the touch screen and activate a program and not the lock thing operators put to limit your phone
I want to know if anyone can help me unlock the screen so that i can reset the phone or alternatively any other method via usb to reset my phone to factory settings. Any special buttons on the phone i can do to do that?
I tired leaving battery out for 24 hours but that did not work to unfreeze the touch buttons
Was thinking to reload the windows mobile completely via the micro card (which i read here) but i am not sure it will work or i fear it might brick my phone
Any suggestions will be welcome please.... thanks
Use myMobiler to control device from Pc through usb
Good luck
Ps: you'll probably have to change digitiser afterwards
Well tried the mobiler but the thing is that it asks the phone to allow the program to conenct and i cannot press yes on the touch screen since it is frozen or something so i am stuck again.
Very strange, it doesn't ask anything on my device...
Why don't you hard reset: press green and red buttons and while pressing, poke the stylus shortly in the reset hole then release the 2 buttons. It will ask something that you probably won't see, just press the action button and wait for it to restart.
Don't flash another on just yet - it may well cause issues as it sounds like your digitizer is broken. Don't hard reset either
Does it pick up anything at all? Have you tried tapping all over the place in that region to try and get a response, sometimes just under the screen also works. Do you use a screen protector? If not, try it with one, if yes, try it without, it may be interferring with it, or it may help the touch be picked up by the phone (Stupid, I know, but this is something I found to work before with my elfs, and omnias)
When it is locked, is activesync picking the phone up? You may be able to put the remote.exe into the windows folder (for myMobilier) and do it that way.
A digitizer costs about £6-£10. But due to the age of this device, as sad as it is, I would suggest trying a new phone out if funds allow for it.
ok so far i tried the hard reset (red button and green and pressed the on off button but nothing. When i press on off button alone it switches off but not hard reset. I did not know i had a reset hole at the bottom of the phone.I did that with red and green button but nothing. Only when i poke the hole alone it does a hard reset i think but when i switches back on it is still unresponsive and locked screen
I tried poking under screen protector nothing. Also i think screen is still responsive because when i tap on it, the screen lights brighter
I tired putting remote exe file on the phone( active sync is working and i can read files on the phone) but i have two remote files..which one to use ? the one that ends with 40 one or 50 .Also where to put it specifically..which folder.I tried my windows mobile based device but nothing.Also tried program files and data application nothing.
Mobiler cannot connect since from pc alone because it asks my phone permission
and i cannot tap yes to accept program.
so any more suggestions please
Hi
Maybe I wasn't clear enough, here's the exact procedure, it should work since you have to use only hardware buttons:
Hold down send/reject buttons (green/red at the front) and reset with the stylus; release the stylus but keep holding the buttons till you get 'this will erase all your personal data' message, then press 'action' (big front button) to hard reset.
If Hard reset doesn't work then your device hardware is faulty.
If he hard resets he will liekly not be able to align the screen on initial setup tito12.
Avanisha. If you try to run one of the remote.exe it will say this is not a valid windows application, thats the one that needs to go into windows on your phone.
captainstu72 said:
If he hard resets he will liekly not be able to align the screen on initial setup tito12.
Click to expand...
Click to collapse
Hi captainstu72, i was under the impression that he messed up something in his system so a hard reset would hopefully solve the problem. In case he still can't align the screen after HR then he has to replace the digitiser. Mymobiler will not solve anything, pls read the 1st post: he wanted to do a factory reset. He just have to sync before HR.
thks tito 12..problem was solved with your help.J ust did not get the steps of hard reset right. Phone is working ok now and screen is ok as well as tap function. thank god i don't need a digitizer. thanks to captainstu72 for the help as well .You were right tito..seems i ran a program and then all hell broke on my phone. I wanted to factory reset but as you know the pad was locked.
Glad I could help, enjoy your device
Ahh okay, guess i mis read something! Sorry
Glad its all sorted though, I was just concerned he may end up in an annoying align screen loop