XDA lli Dead - Srceen onlu USB 1.0 - PDA2, XDA IIi, 2020i Software Upgrading

I try to upgrade my rom and it go dead. all it got on the screen is black and white with word, USB on top v1.01 on the bottom...
What can i do??? help help

wrong forum it's no xda1
your device is in bootloader mode try
flashing it again

Related

urgent, Have a Blue screen in my O2 XDA

Here is the situation:
Tried to upgrade my XDA to Wallaby, the final result is I have what they called a blue screen (White screen with a red bar in the top).
Urgently need to let the phone work again, even with the normal 2002 WM
Any help with details please, I have both USB and serial cable and I do not have SD card now.
no worrrrries looooks like ur in booooot loader mode....try a hard reset....try a soft reset....if both dont work download any rom (latest thats come out for xda) and if you have xda II then go for mysteryman rom and try an upgrade you will be fine......
regards
jeetz

Bricked m600

ok i think iv killed my m600
i flashed it with the older imate rom the 1.0.9 version
it installed 100% and rebooted and from ther it was stuck on the imate screen for like 10 minutes and i see the following text in red on the top left corner
---------------------
IPL 2.10.0001
SPL 2.15.0001
GSM 01.14.20
OS 1.0.9.25
-------------------------
i tried removing the battery and restarting the fone. still the same thing. can someone please please please help me with this?
what do i do?
im sure orange wont help me out since i flashed it with a non-orange rom.
never mind fixed itby goin into the bootloader
funky_Saggi said:
never mind fixed itby goin into the bootloader
Click to expand...
Click to collapse
hi there i seem to have the same problem as you with the boot screen. top left corner say's
IPL 2.10.0001
SPL 2.10.0001
GSM 02.07.20
OS 1.0.13.21
can you please tell me how you fixed yours please it would be a great help
What you could do is flash it with an newer rom
Hold camera button AND reset (be asure that it hold it while resetting)
Then... you are in you bootloader... connect the PDA with your PC..it will recognized it!
Then run the romupdate ;-)
Hi thanks for trying to help me i got my phone in to the 3 colour screen but my computer does not pic it up at all. is there another way to save my M600
crossy4life said:
Hi thanks for trying to help me i got my phone in to the 3 colour screen but my computer does not pic it up at all. is there another way to save my M600
Click to expand...
Click to collapse
Aren't you getting "USB" written in the bottom left corner of the 3 colour screen when you connect it to USB?
Yes i get the USB come up at the bottom of the screen my computer does not do anything. can you tell me which ROM i will need as the ones i have to run the ROM update but it comes back saying connect to ActiveSync which i can not do is there a way round this?
Final got my SPV M600 Working with the ROM from the download area thanks for the help anyway
cheers
just change the usb port to another one and start rom it should pick it up

Help for my dopod 818pro

my dopod 818 pro when i turn phone on , it will blink like lcd goes wrong , when i go into bootloader mode , its only show IPL 3.08 AND SPL 3.08 , what should i do now . please help !
Did the three color appear?
owleng said:
Did the three color appear?
Click to expand...
Click to collapse
when I connect the device to the charger the 3 colors appear
but when I connect it to the usb cable the screen is flicking with no responce
in the activesync.
Sorry I have the same problem and I even thought this is my post
yes i can go into bootloader mode , the 3 colour can be appear

colored bootscreen

Hello guys, I hope you can help me.... In the middle of a ROM update my (!#@#[email protected]#) PC rebooted.... (while in the white screen on my Qtek 9100) Now the only thing it will come up with is the colored screen saying: IPL 2.21.0001,SPL 2.21.0lip and the USB is on. Active sync isn't able to connect to my device so now what?? Is it bricked?
Hope sombody can help me.... the colored screen means something's still working isn't it?
thanx in advange,
NEVSKI
what update were you trying to install? WM5? WM6? Official or cooked?
What windows xp/Vista are you using?
How far had the update gone
Have you tried running the update again,just tick the i have an active sync connection ,even though you dont and see if it will update? While in the bootloader screen the coloured screen. Hopefully it will do it for you
NEVSKI said:
Hello guys, I hope you can help me.... In the middle of a ROM update my (!#@#[email protected]#) PC rebooted.... (while in the white screen on my Qtek 9100) Now the only thing it will come up with is the colored screen saying: IPL 2.21.0001,SPL 2.21.0lip and the USB is on. Active sync isn't able to connect to my device so now what?? Is it bricked?
Hope sombody can help me.... the colored screen means something's still working isn't it?
thanx in advange,
NEVSKI
Click to expand...
Click to collapse
Its a bad flash as your PC crashed,the update did not finish and you don't have a working OS on your device.As long as you are getting into Bootloaders (multicolored screen) the phone is working,it's definitely not 'Bricked'.,but bad flash might have corrupted the bootloaders (IPL/SPL) on your phone.
Therefore to recover it back to it's default status,download the official carrier's Rom from it's website and flash it in bootloader mode(multicolored).You don't need to establish Activesync connection as Activesync will not work in bootloaders.Just get the phone in bootloaders ,connect your phone with the pc via usb cable,check usb appear at the bottom of the bootloader screen in the phone and run the Ruu in the rom,let it finish and reboot,hope it'll recover to it's default working status and than do what ever you want to do.
Good luck
still a No Go......
well, I still got the 3 (with the white 4) colored screen saying: RUU, IPL 2.21.0001, SPL 2.21.0lip and USB in the white...... I tried a RUU but that didn't work. I had this phone flashed with WM 6 DUTCH and it worked like a baby untill I tried to SIM unlock it... doing that the PC crashed.... Explain please how to get the right ROM and maybe some more info on how to do it after I got the ROM downloaded.... I want my Qtek so bad....
NEVSKI
Yeeeeeeehaaaaaaa!!!!!!! I got it 'up 'n running'....
NEVSKI
igot the same problem
it comes up with the 3 colourd screen usb at the bottem in the white when i put usb cable in but wont connect to active sync i dont no whare to get the 02 rom from can any on help please

is there something to do 4 thos wizard

I had a wizard and trying to fix it.
When switch on, blue cingular screen appears and show ipl spl gsm os numbers.. and halts on.... it stays like this...
i enter RGB screen it says ONLY `ipl 2.25 spl 2.25` ...
when i connect it to usb.. USB text appears but when I try to install `love ROM` RUU says, it is not connected check computer check usb cable.. so it is invisiable for computer but in device manager it s shown as winCE syc device when I connect..
do u think it is bricked.. Or theres some to do....
thanks
it wasnt dead...
thanks to this forum!!
m_carleone82 said:
I had a wizard and trying to fix it.
When switch on, blue cingular screen appears and show ipl spl gsm os numbers.. and halts on.... it stays like this...
i enter RGB screen it says ONLY `ipl 2.25 spl 2.25` ...
when i connect it to usb.. USB text appears but when I try to install `love ROM` RUU says, it is not connected check computer check usb cable.. so it is invisiable for computer but in device manager it s shown as winCE syc device when I connect..
do u think it is bricked.. Or theres some to do....
thanks
Click to expand...
Click to collapse
Hi,all,i have this problem........ipl 2.17 spl 2.17....please help.......
m_carleone82:
press Camera+reset to enter RUU mode, then flash with Cingluar original ROM.
starkwong said:
m_carleone82:
press Camera+reset to enter RUU mode, then flash with Cingluar original ROM.
Click to expand...
Click to collapse
Hi Starkwong.....i have the same problem .....can i reflash to original rom even my MDA is not recognized by my PC?.....thanks for your reply
ichiban said:
Hi Starkwong.....i have the same problem .....can i reflash to original rom even my MDA is not recognized by my PC?.....thanks for your reply
Click to expand...
Click to collapse
Yes ! if it gets into Bootloaders mode(tricolor screen) with ipl/spl display and when hooked up with pc via usb,a small usb appears at the bottom of the Bootloaders,it means it has connectivity with the pc,You can flash the official rom in the Bootloaders.
ahhh, hardreset. the pumpkin in my eye.
"m_carleone82:
press Camera+reset to enter RUU mode, then flash with Cingluar original ROM."
I´m right now on the RGB screen , and how can now put the original ROm????
please help me
thx
hugomalheiro said:
"m_carleone82:
press Camera+reset to enter RUU mode, then flash with Cingluar original ROM."
I´m right now on the RGB screen , and how can now put the original ROm????
please help me
thx
Click to expand...
Click to collapse
While in Bootloaders (RGB) screen,hook up the phone with pc via usb cable,watch small usb appear at the bottom of the Bootloaders,run the RUU in the Rom you downloaded,follow the instructions,it'll start to flash.let it finish and the phone will reboot.

Categories

Resources